Can't Connect Directly To Wifi But Can Using IPhone As Hotspot - Limited Access, Changing It To Public Network Etc

Feb 8, 2012

I have been using my home internet in my new place for a couple of weeks fine, yesterday morning when I tried it it had the limited access yellow triangle and wouldn�t connect.I reset the router and connected to the wifi on my iphone which worked fine, I checked the DNS numbers were the same as on my iphone which they were and I had not changed any settings. I spent the entire day yesterday online looking for solutions, I�ve reset the adapter, disabled it etc, set the ip and dns to automatic and back again etc etc.
When my wifi tries to connect to my home internet it takes a LONG time to identify and then identifies it either as an unidentified network and/or public. Even when I change it to home it changes it back to public or just doesn�t let me change it to home and says try again later.

Ps- I just tried disabling then re-enabling the protocol 6 on the wifi which isn�t working and it just said �in order to configure TCP/IP, you must install and enable a network adapter card. But then it just let me configure it and is still connected but with limited access and public network.

View 9 Replies


ADVERTISEMENT

Unable To Connect To Wifi - No Network Access/limited Access

Nov 10, 2011

Last night I was on the internet at home absolutely fine and my laptop automatically downloaded an update, since then I have been unable to connect to my wi-fi. I deleted the updates and was still unable to connect, so I tried to used a system recovery restore point and every one I use starts but fails to complete.So, I did a factory reset after around 8 hours of trying to sort it out today and I STILL have the same problem. I can plug in the cable to connect and my housemate is having absolutely no issues connecting and neither is my phone so now I am at a total loss what I should do to resolve this. Prior to the factory reset I was able to connect to the wi-fi but it was stating no network access/limited access and now it simply won't connect to my internet at all. It finds my full strength signal but will not connect.My drivers for the Broadcom 4313 802.11b/g/n card are the most up to date and the laptop (HP G62) says it is working fine.

View 2 Replies View Related

Cannot Connect To Network - No Cable Plugged In / Limited Access

Jul 19, 2012

My laptop suddenly stopped being able to connect to the network in my house and for that obviously it doesn't have any internet. It doesn't work either by connecting a cable or trying to use the wireless, here are the detaills for each case: When I connect the cable, the laptop detects it, but doesn't detect any network, it doesn't seem to even be trying. I checked on the network adapters, and it clearly says "enabled" when connected and when disconnected it changes to "No network cable plugged in". When I try to connect to my network, it always ends up saying "Limited access", when I tried troubleshooting, it said that there may be an error with the network drivers, I tried the fix there, and then it says that there must be an error with the network adapters.

Here's what I have tried so far:
-Reinstalling the devices and drivers, when I check them in device manager, it says that both the wireless and network driver are working properly.
-I tried resetting the router.
-Tried resetting the bios of the computer to it's factory ones.
- Tried resetting IPv4 and IPV6, along with the IP/TCP using the command prompt, still no go.

When I try to ipconfig /release or ipconfig /renew, I get an error saying the next thing: "An error ocurred while releasing interface Loopback Pseudo-Interface 1: they System cannot find the file specified. The operation failed as no adapter is in the state permissible for this operation."

Here is my info when using ipconfig /all:
Host name... : Jorge -NB
Primary Dns Suffix : Empty
Node Type : Hybrid
IP Routing Enabled: No
Wins Proxy Enabled: No

Tunnel adapter teredo tunneling pseudo-interface:
Media state: Media disconnected
Connection-specific DNS suffix: empty
Description: Teredo Tunneling Pseudo-interface
Physical Adress: 00-00-00-00-00-00-00-E0
DHCP Enabled: No
Autoconfiguration enabled: Yes

View 2 Replies View Related

Modem And Router Will Not Connect To Computer Only Shows Unidentified Network/public No Internet Access, Wired Connection

Nov 11, 2010

For some reason my router and modem will not show correctly on my dell inspirion one desktop. Im running windows 7 and here are the net work connection deatils

Connection -specific DNS Belkin
Description Realtek PCIe GBE Family Controller
Physical Address 00-00-00-00-00-00
DCHP Enabled Yes
Ipv4 Address 192.168.2.2
Ipv4 Subnet Mask 255.255.255.0
Lease obtained Wednesday, November 10, 2010 9:45 PM
Lease Expires Sunday, December 18, 2146 4:17 AM
IPv4 Default Gateway 192.168.2.1
Ipv4 DHCP Server 192.168.2.1
Ipv4 DNS Server 192.168.2.1
IPv4 WINS Server
NetBIOS over Tcpip enabled Yes

The Connection was working about ten days ago and then suddenly stopped and read as an unidentified network no internet access. at one point is was not receiving packets but now it is but it still says no internet access on the IPv4 Connectivity. Media state is also enabled and the speed is 100.0 Mbps when i troubleshoot it says windows cant identify problem but in the details it says default gateway is available. when i use the cmd prompt ipconfig/all my local ethernet adapter has a physical address of all zeros.

View 9 Replies View Related

Network Constantly Changing Between Unidentified Public Network And Home

Aug 30, 2012

Home network with Wifi and ethernet. Using 3x Notebooks and 3x workstations. One of the workstations (W7 ultimate) keeps changing between Public and Home. When this happens, the internet connection dies. I cannot see other workstations either when on public network. Workstation using wifi. Does the same on cable. When it changes to Public, it disconnects from the internet and I cannot get to the router even though it has the workstation has an IP(DHCP or static). Default gateway and subnet is correct. TCP v4 is being used and nothing else is enabled.

Why is this happening?
- I have tried DHCP as well as Static addresses
- Reconfigured NIC(Netgear WG311T), uninstalled and reinstalled it.
- Removed Wifi connection and re-added it.
- Changed auth type, encryption type and keys to connection

Have I covered everything? The only thing different is that I installed a new router - Duo Plus 300wr. It cannot be the router because all the other notebooks connect to it wireless and so does my iPad, Android device and tablet...so it rules that out?

View 3 Replies View Related

Wifi Has Limited Access?

Sep 30, 2012

im having trouble with my wifi. The day before it works fine but then the next day i turned on my Vaio laptop and it says Limited Access to my home wifi. I tried connecting to other wifi but same thing. I tried resetting the router, disabling and enabling the wireless connection but all didnt work. I tried connecting it with the cable directly still cannot connect. Finally i did a system restore to the day before where its working fine, it worked. The next day it says Limited Access again! So im guessing 'something' made my wifi error after that 1 day and i dont know what to do

View 3 Replies View Related

Windows 7 Starter Won't Hotspot With IPhone

Sep 6, 2011

I have Win 7 Starter on an Akoya/Median Netbook and I can't get the system to accept my iPhone as an internet 'Hotspot' either in Bluetooth, or with the USB cable.

I have Vista and XP on other machines and it was relatively easy to setup.

View 2 Replies View Related

Unable To Ping IPhone On Any WiFi Outside Home Network

Sep 7, 2011

There's a program I use (Pocket Informant iPhone Outlook Sync) which requires that my PC and iPhone be on the same network in order to sync.

The problem is that it works only when using my home network. When I'm at home, from my PC I am able to successfully ping my iPhone, which is connected to my WiFi network. This works whether myh PC is also ethernet-connected or WiFi-connected.

When I travel, however, even though I successfully connect to the WiFi network on my iPhone and PC, I am unable to ping my iPhone.

I have tried disabling the Windows Firewall and I get the same result!

I can't believe that all these different WiFi networks I connect to (airport, hotel, work) that they all have a configuration issue, so I'm thinking that the reason for the discrepancy must be because of some setting/configuration on my PC/home network.

Is there anyhing else besides disabling the Windows Firewall that I can try?

View 9 Replies View Related

Wireless Connection Limited Access After Changing Router Setting MCS?

Jan 5, 2013

I have found a wireless connection near me and connected to it. I saw that my speed is kind of good (about 14 Mb/s), I tried to get this speed higher.I went into the router setup from my browser, and changed some settings from thereOnce changed, I reboot the router to see if it changed my speed.The one setting that blocked my access to internet is MCS. I don't remember if that was off/disabled, but i changed it to MCS7, the last option available for MCS... thing.

View 4 Replies View Related

[WiFi] Limited Access (Dell Laptop) ?

Jul 17, 2012

I have a Dell Inspiron laptop that won't connect wirelessly to my network. ALL other devices in the house (iPhones, iPads, iMac, 1 laptop and another desktop) work fine, no problems. I've tested the laptop at my girlfriend's house using her wifi and still the same problem: Limited Access.

I've ran the troubleshoot, re-booted the router & laptop, checked device manager for any exclamation marks against any drivers (none), tried disabling/enabling the driver, checked for driver updates (none), done a system restore and uninstalled my antivirus software but all to no avail.

Edit: I've tried plugging in the ethernet cable which, although not particularly straight-forward, eventually works.

View 6 Replies View Related

Can't Connect To Home Wireless / Limited Access

May 12, 2012

A few hours ago I installed a Windows update, so my ACER Aspire 5733 restarted. I shut it down after the restart, not paying attention to the wireless. When I went to turn it back on, I couldn't get online because my home wireless connection has "Limited access."The icon signifying signal strength on the taskbar has a small yellow star-shaped dot on it. When I click on it, it pops up and says "Not connected. Connections are available. It then says my wireless network name and says "Limited access" next to it. The signal strength is excellent.When I disconnect and then reconnect it says the connection was unsuccessful because the computer has limited connectivity.The same network is working on my other laptop and on my iPod, but not on my Aspire 5733.

View 9 Replies View Related

Limited Access Wireless? Cannot Connect To Internet On Only One Machine?

Jun 17, 2011

So yesterday my internet was working fine, but today when I returned and got it out of standby, I could not connect to the internet. It says "limited access" when I try to connect to the wireless, and when I try to connect with an ethernet cable nothing happens.If I troubleshoot, Windows is unable to resolve it. The problem it says is:There might be a problem with the driver for the Wireless Network Connection adapter.There might be a problem with the driver for the Local Area Connection Adapter.

View 9 Replies View Related

Cannot Access Network Location %PUBLIC%Desktop

Nov 21, 2011

I'm trying to open and download apple, itunes. I've downloaded the program and its giving me a cannot access network location %PUBLIC%Desktop. ive also found a microsoft

View 5 Replies View Related

Unidentified Network, No Network Access, Limited Access

Dec 29, 2009

I have a brand new acer aspire notebook and I'm trying to connect to my airport extreme card built into my iMac desktop. The laptop sees the signal just fine, but it will not connect to the Internet and I get "limited access". What can I do to connect?

View 1 Replies View Related

BSOD - Limited Access On Wireless Network

Mar 29, 2012

A few days ago I booted up my HP Pavilion dv4-2049wm laptop. Windows update needed to reboot, due to my postponing it for a few days, so I let it reboot and I started getting blue screens. After a few restarts (getting the BSOD every time), I booted into the last known good configuration. It booted up fine, but now I can no longer connect to my network (wired and wireless). It sees my wireless connection, but states "Limited Access."

Things I have tried:
- Uninstalled/Updated network drivers from HP's site, specific to my laptop model.
- Uninstalled all windows updates that were installed before BSOD
- Flushed, registered, renewed dns via command prompt
- Reset Winsock via command prompt
- Tried a "clean" boot
- Ran Windows Check Disk
- Ran Windows Memory Tester (Unsure of exact name)

On the day of the crash I attempted to do a restore, but the earliest restore I could do was at the time of the windows update (same time as BSOD). One thing I did notice is that the "Teredo Tunneling Pseudo_Interface" listed under network adapters is no longer there. Not sure what that might have to do with anything. I ran this tool (Who Crashed/Crashdump) and here is my log:

Code:
System Information (local)
computer name: DECARO
windows version: Windows 7 , 6.1, build: 7600
windows dir: C:Windows
CPU: AuthenticAMD AMD Turion™ II Ultra Dual-Core Mobile M620 AMD586, level: 16
2 logical processors, active mask: 3
RAM: 4022542336 total
VM: 2147352576, free: 1925451776
Crash Dump Analysis .........
[Code] ....

On your computer a total of 26 crash dumps have been found. Only 21 could be analyzed. Only 15 are included in this report. 2 third party drivers have been identified to be causing system crashes on your computer. It is strongly suggested that you check for updates for these drivers on their company websites. Click on the links below to search with Google for updates for these drivers:

atikmpag.sys (AMD multi-vendor Miniport Driver, Advanced Micro Devices, Inc.)
athrx.sys (Atheros Extensible Wireless LAN device driver, Atheros Communications, Inc.)

If no updates for these drivers are available, try searching with Google on the names of these drivers in combination the errors that have been reported for these drivers and include the brand and model name of your computer as well in the query.

View 9 Replies View Related

Network Wireless Adapter - Limited Access

Jan 27, 2012

My new Samsung laptop has just stopped allowing me access to the internet. Its not a problem with the router as I have a wired connection to a desktop that is fine. My laptop has been working ok but now I just get 'Limited Access' from the status bar. All the other checks have been made with ISP the Intel(R) Centrino(R) wireless N130 is supposed to be working according to the network properties dialogue box. Also have wired the ethernet from desktop to laptop and still the same response so narrowing it down to the possible driver software.

View 1 Replies View Related

'Limited Access'- Wireless Network Connection?

Jul 25, 2010

I cannot access my internet and don't know why. When i try to access the internet it says I have 'limited access' although I have a full internet connection. Does anyone know how to fix this please? I have a Windows 7 operating system

View 9 Replies View Related

Limited Connectivity Over Public Wi-fi

Feb 3, 2012

I just recently purchased my Asus X53SV-MH71 laptop. For the first week I was able to connect to internet/wifi at my school perfectly fine. But now it keeps coming up as "Limited Connectivity." I've read some solutions over the web but none have seem to solved my problem. At this moment I am currently connected through an ethernet cable. If anyone can help me that would be great. I will provide the "ipconfig /all" cmd below.

View 1 Replies View Related

Wireless Network - Limited Access Message Comes Up For No Reason

Jun 17, 2011

I have an issue with my wireless. It comes up now (for no apparent reason) that the network has Limited Access.

View 1 Replies View Related

Limited Access To Wireless Network, Automatic Update Error?

Sep 13, 2011

I have this problem with my new Asus laptop which was fine yesterday, but cannot connect to any wireless network now. When I click the Network connections button on my task bar it shows me my internet connection with the words Limited Access next to it. I've been on google for a good 2 hours and can't really find the answer. I may know what's wrong, however. Yesterday I pressed the shutdown button on my laptop and then it starts those automatic updates that happen when you shut down. It said something like "Updating 1 of 1 updates". It took a while so I put thelaptops screen down, and when I checked on it again 5 minutes later... Blue screen. I held the power button down on my laptop and shrugged it off.. but now I can't connect to any wireless network.Assuming the network driver is the thing that was updating last night, I searched up what to do, Rollback the dri

View 1 Replies View Related

"Limited Access" WiFi Connectivity After Virus Removal, Registry Edit?

Sep 6, 2011

I'm trying to fix my girlfriend's Windows 7 laptop after she had a virus/malware infection. I'm pretty sure we've successfully cleared the virus (an updated/full scan with Malwarebyte's Anti-Malware in safe mode comes up clean). However, we have had no Internet access since the infection. The wireless router/connection itself is fine (I connect to it daily with my laptop, as I am to write this post) but her laptop won't connect to it, we can't browse any web pages.I may have made the problem worse in trying to resolve it. I stupidly followed the advice on a forum for some registry edits for Windows XP--deleting WinSock and WinSock2 from the registry and then restarting the computer in hopes they'd re-register themselves. Unfortunately, WinSock2 re-appeared but WinSock did not. I'm wondering if this has created a new problem (or compounded the problems we were already having).In diagnostics, we currently get the following report: "Wireless Network Connection doesn't have a valid IP configuration." I just ran an ipconfig in the command prompt and got the following results:

Windows IP Configuration

Host Name . . . . . . . . . . . . : Elizabeth-PC
Primary Dns Suffix . . . . . . . :
Node Type . . . . . . . . . . . . : Hybrid
IP Routing Enabled. . . . . . . . : No

[code]....

View 2 Replies View Related

Can't Connect To Home Wireless Signal ("Limited Access") - Windows 7?

Dec 23, 2009

I am setting up a new Acer laptop and cannot access the internet via my home wifi network. I have 2 other laptops connected to the network and running fine. The new pc is running 64 bit Windows 7 (the others run XP) and has an Atheros AR5B93 Wireless Network Adapter. When I pan over the wireless icon in my taskbar, it says "Limited access" beside my home wifi signal.

View 9 Replies View Related

Internet Disconnects, Won't Connect And Shows "Limited Access"

Feb 9, 2012

My internet is connected to a laptop downstairs as well as mine (sometimes but rarely). I often cant connect. It comes up with a box that says "Connect to a Network" and for options, "Troubleshoot problems" or "Tell me more about Internet connection problems". I click "Troubleshoot problems" about 5,000 times a day (no joke) and about 20 of those times it fixes the problem. The other times it does nothing and I have to go shut off the downstairs computer and unplug and plug back in the router about 10 times. Then sometimes is works for 10 minutes or so, and sometimes it doesn't. If I ever do get it working, it never ever stays working. Most times when the internet does connect, it works for about 30 seconds then shows a yellow triangle warning said with an exclamation mark stating "limited access". My SGS2 phone connects just fine. So does the laptop downstairs and any other gadgets except for my desktop! This is frustrating as anything!

View 7 Replies View Related

How To Turn Pc Into Wifi Hotspot

Aug 31, 2011

i got 2 samsung galaxy devices and i can use one of them to act like a wi-fi router with the internet connection from my pc, my question is, how do i do it? i installed virtual router manager and it doesnt work

View 9 Replies View Related

Unable To Connect Use Internet. 'Limited Internet Access'

Nov 17, 2011

i recieved my new lenovo z570 ideapad yesterday...i'll just put some of the spec down incase you want to know.

proccessor: intel i5 (second gen)
graphics: nvidia geforce
os: windows 7 64bit
yadayadayada...

anyway, after charging it up and turning it on, i started to install programmes and other bits and bobs. e.g ituens, flash player. just the usual essentials. i used the laptop to watch videos on Internet, genenral browing such as facebook, so in short, the internet was working fine. just before i went to bed that night i installed avg security (free version) and ran a full scan. when the scan finished, i put the laptop into hibernate, and went to sleep! happy in the knowledge my new gizmo was running smoothly!

just before i woke up i heard the laptop turn off as it had run out of charge. so i plugged it in and charged it up, then turned it on. this is where the problem starts...i connected via wifi however the logo at the bottom right of the screen showed the signal strength meter on empty, with a yellow star covering it. i clicked the icon, and it said, 'not connected, connections are available' and below shows im connected with 5/5 signal strength, but on 'limited access'.

1) there might be a problem with the driver for the local area connection adapter

2)there might be a problem with the driver for the wireless network connection adapter

there are 28 updates, but im unable to update them as i have no internet connection. i also cant connect via the ethernet cable.i cant roll back the drivers as there are no previously installed ones, and i cant update them as i am already up to date.my other laptop (acer aspire 5630 running on vista) works perfectly fine using wifi and the ethernet cable, so i honestly dont know whats wrong. after reading things on my acer about ways to fix the problem i came to the decision to restore the laptop to the time of my first installation which was adobe flash player (which i installed the day before.) i was unable to do a full factory reset as the only options available are to either restore to a backup, or re-install windows (which requires a disc, which i dont have). i also didnt configure a backup as i had only had the laptop a day!

View 9 Replies View Related

URL Not Found When Surfing On Hotspot Wifi?

Sep 30, 2012

I've been trying to setup my own personal hotspot wifi, but it seems the internet connection is always limited and it always displays the "URL is not found on this server" page.

I am using Intel MyWifi Technology, and then tried using connectify, to no avail.
I did an Intel PROSet Wireless manual diagnostic to found it failing at the association test.

I can connect to the wifi hotspot, but just have no access to the internet.

View 1 Replies View Related

Computer Connect To Wifi But Show No Internet Access?

Dec 30, 2012

I have sony laptop, i have install the internet driver, but i cant access network. i connect through wifi and i have all info of wifi eg. Username and pasword but that shows no internet access so

View 1 Replies View Related

No Internet After Turned Laptop Into Wifi Hotspot

Oct 12, 2012

How to turn your Windows 7 laptop into a wireless hotspot.I thought, "Hey, that's cool". So I did everything mentioed there to the letter. It worked, my laptop was able to create its own hotspot, which was well cool. I connected my tablet to the new wifi connection. It did work, but I had no internet connection.

View 9 Replies View Related

Turn Windows 7 Laptop Into A Wifi Hotspot?

Dec 14, 2012

I have a windows 7 Dell laptop and using USB modem for internet.

I would like turn my laptop as wifi router so that i can share the internet to my mobile devices.

Also, I heard that we can share the internet via that intel my wifi technology too.

View 1 Replies View Related

Wifi Hotspot Software Compatible With Hp Dv6000?

Aug 7, 2012

i have installed windows 7 on Hp dv 6000 SERIES...originally it had Vista. now i want to make wifi hotspot to get internet on my cell phone via laptop....but software like " Connectify and Maryfi" show a wireless cadr error..

View 1 Replies View Related

Can Only Connect To Home WIFI, Possibly Due To No System Icon Access

Dec 28, 2011

About 3 weeks ago, I was using a public WIFI connection. *something* went wrong, my computer froze up, and ever since, my system icons have been disabled and I can only connect to my home WIFI connection - by going to the control panel and manually connecting. Since I no longer have my connectivity icon, I can not view the available networks, and therefore cannot select one to connect to. Only my home WIFI connection works.This is bad, since I will be moving soon and leaving my home network. I have tried every tutorial I have found.....my last resort would be reinstalling the OS...but I'm not even sure that would work. I am running Windows 7 Home Premium.

View 9 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved