64Bit Ult Won't Boot When 'Memory Remap' Is Enabled To Use All 4GB RAM
Mar 12, 2012
I will start off by stating my relevant PC Specs for this thread:-
Asus P5B Deluxe MoBo
Intel Dual Core E6600 @ 2.40GHz
GeForce 7900 GS 512Mb
2 x 1GB DDR2 800MHz Corsair Value RAM (original) in Yellow Slots A1 & B1
2 x 1GB DDR2 800MHz Corsair Gaming RAM (NEW) in Black Slots A2 & B2
So I have just installed 2 extra GBs of RAM to bring my total to 4GB. After a successful boot and then checking my 'System' info Windows states 4.00GB of memory is installed but only 2.94GB is usable.Therefore I went ahead into my BIOS to enable the 'Memory Remap Feature'.However on reboot the PC gets to the 'Starting Windows' screen and doesn't get any further. The Windows logo doesn't start to appear. It just restarts going through all the usual screens again, eventually giving two options of:-
Launch Startup Repair
or
Start Windows Normally.
The repair never works and Windows will never start normally again until I return to the BIOS to disable the mem remap.Sometimes I have had a Blue Screen displaying the same errors as this thread:-Windows 7 64Bit BSOD's (IRQ_NOT_LESS and BAD_POOL_HEADER)I reset the CMOS to Factory Default settings and tried again but did nothing. Also I have never updated the BIOS from the original version as I'm a bit scared to do so.Have read about graphics card using part of the mem (which doesn't seem right with the 7900 GS as has it's own onboard mem) and also that voltages to the RAM should be increased.
MCH Voltages
Windows 7 :: Win 7 Wont Boot With 4GB RAM
Windows 7 RC won't boot with 4gb
I have looked hear for info on voltages and clocking but didn't get anywhere. Well got an overclock at 3.60Hz but only ran in Safe Mode. Obviously this is slightly irrelevant the above but was just trying stuff out and trying to learn more.
I will start off by stating my relevant PC Specs for this thread:-
Asus P5B Deluxe MoBo Intel Dual Core E6600 @ 2.40GHz GeForce 7900 GS 512Mb 2 x 1GB DDR2 800MHz Corsair Value RAM (original) in Yellow Slots A1 & B1 2 x 1GB DDR2 800MHz Corsair Gaming RAM (NEW) in Black Slots A2 & B2
So I have just installed 2 extra GBs of RAM to bring my total to 4GB. After a successful boot and then checking my 'System' info Windows states 4.00GB of memory is installed but only 2.94GB is usable.Therefore I went ahead into my BIOS to enable the 'Memory Remap Feature'.However on reboot the PC gets to the 'Starting Windows' screen and doesn't get any further. The Windows logo doesn't start to appear. It just restarts going through all the usual screens again, eventually giving two options of:-
Launch Startup Repair or Start Windows Normally. The repair never works and Windows will never start normally again until I return to the BIOS to disable the mem remap.I reset the CMOS to Factory Default settings and tried again but did nothing. Also I have never updated the BIOS from the original version as I'm a bit scared to do so.I have looked hear for info on voltages and clocking but didn't get anywhere. Well got an overclock at 3.60Hz but only ran in Safe Mode. Obviously this is slightly irrelevant the above but was just trying stuff out and trying to learn more.
If I disable Network Boot in my BIOS I get Boot Failure when I try to boot. My Boot Options are CD/DVD/Hard Disk/Removable Drive. Do I have a problem? or should Network Boot always be enabled?
Windows 7 boots to a black screen. Running on a dell e520, I've used the dell diagnostics to scan all the hardware, no issues were found. Computer works more then fine when windows boots. boots into safe mode, and runs when i select the debug option from the safe mode boot menu. also booted once or twice without keyboard connected.
Whats inside the computer besides the processor and a hard drive? zotac 9800 gt : OC to 630mz with rivatuner (stable, machine doesn't boot with OC disabled) crappy sound blaster audigy.
The problem is recent, no hardware changes where made in the last 6 months. (problem never happened in xp)
I have an MSI Wind 123 netbook and, for some odd reason, MSI put the Fn key to the left of the Ctrl key on the far left hand side of the bottom row. This is a real nuisance.
Can anyone tell me how to swap functionality of the two keys, so it is consistent with my other keyboards?
I have a racing wheel, and currently the only way to have pressure sensitive pedals is having them both on the same axis, the y axis. Unfortunately, this means pressing them both at the same time means they cancel eachother out, and doesn't do anything. How do I remap one of the pedals to the currently unused Z axis?
i would like to use custom themes on a school computer that does not have admin, so i thought i could just use batch to make windows think the folder is in another location. i coded this: [code] but it does not work and any theme that i put in that test folder does not show up. i also shut down explorer.exe and used explorer++ to launch the batch file to try to make sure the changes were being applied, but it still didnt work.
I have an old keyboard but I like it and I don't want to change it. This is it: Trust.com - Multimedia Keyboard KB-2100EI want to remap the keys under the scroll to do something else.They now have: Ctrl+X, Ctrl+C and Ctrl+V on them. I want to put another key combination to each one.I tried hotkeyp but that only replaces ctrl+v ( the current combination in place ) etc with the new combination and I can't use ctrl+v anymore. I need those hotkeys to be available all the time, so to start and stop hotkeyp is not an option.
my windows 7 64 bit system is only seeing 2.87gb of the 4gb installed memory. checking the Resource Monitor, it says 1153gb has been allocated to Hardware Reserved. any idea how i can use all the memory? i have already tried unchecking Maximum memory under msconfig/boot/advanced options without success. below is my system properties. i have flashed my system with the latest bios.
OS NameEnter text here. Microsoft Windows 7 Ultimate Version 6.1.7600 Build 7600 Other OS Description Not Available OS Manufacturer Microsoft Corporation System Name SOLO-PC
I have Win7 64bit with 6GB memory. The Windows System control panel agrees with that showing 6GB ram and nothing about a limitation. But today I was opening a lot of files and the program wouldn't let me open more files after Windows memory use reached 4GB. Task Manager showed 4GB used out of 6GB. I tried opening another file with a different program and my screen flickered and the program shut itself off, so it looks like the problem is with Windows and not the other programs. How do I get Windows to use all available memory not just 4GB out of 6GB?
While installing a printer software, a "insufficient memory, need 55 mb to install" message appears and installation stops. I have 366GB available in HD and 4GB RAM. What can I do?
So my problem is I use to have 5.74GB of ram usable out of 6.00GB. Since a restart of my computer there is now only 1.74GB out of 6.00GB.So I have a 64-bit Windows 7 Home premium SP1.The ram is 1066MHz with 1 x 4GB and 1 X 2GB.I only have 2 slots on the computer.
I recently opened a minecraft server, not knowing that online my minecraft would run slower. I'm not 100% sure if its because i only have MB of dedicated video memory, but i'm pretty sure it isIs there anyways i could increase this or get other options on how to help my computer run minecraft
I just rebuilt my computer, new motherboard and such and it has 6 GB of ram installed but it is only using 2 GB and has 4 GB hardware reserved. I have went and set the bios settings to memory remapping, I have tried reinstalling windows, I've tried unchecking the msconfig max memory, resetting the ram, and resetting the bios.
In the Systems window it reads that there is Total 6 GB Memory and only 2 GB usable, and in the Bios in the System information it also reads only 2 GB usable memory. The ram sticks aren't new, I took them form my old computer when I did the rebuilt, which are 3 Elipida 2GB 1333 MHz sticks. The motherboard is a Maximus III Gene with bios version 2103. OS is Windows 7 Pro 64 bit.
I tried looking online about this I need to know if there's a big difference between 12GB of system memory and 16GB of system memory. I don't play many games but I do convert HD videos a lot and these programs are a pig on ram. I have 8GB now and have ordered 2 4GB sticks and was wondering if I should stay with 2 4GB sticks and 2 2GB sticks(total12GB) or should I upgrade to 16GB.
I've had 4gigs of RAM installed for very long and I was able to work fine with my browser open + Photoshop and Blender in Win XP. I've quite recently upgraded from Win Xp 32bit to Win 7 64bit. After installing Win 7 64bit I added 2x1GB sticks into my system to take advantage of memory I had available. These "new" sticks were of lower clocks than my 2x2GB I had installed so I tested clocking them higher. Well that wasn't really stable so I figured running them at lower clocks wouldn't hurt all that much.
So everything seemed to work fine, Memtest didn't whine about anything and everything seems to work well enough. Now however I can't have my browser + the other programs open at the same time but windows keeps whining about it running out of memory even though the taskbar memory amounts don't add up at all. I have like 5Gigs used but adding everything doesn't even get up to 2Gigs. I know about windows keeping unused memory ready for use but it doesn't seem to be that or otherwise I don't know why my programs keep crashing all the time.
I have a load of tabs open in my browser but they don't take all that much memory. And I don't have any other programs open that would use that much for anything. My display turns black sometimes and sometimes (not every time) after that I get the display driver error and that it's recovered. I've had this very seldom before but now it seems quite common so I figured it might have something to do with that the display driver doesn't get enough memory to use either. Just a wild guess but textureloading in Blender doesn't work all the time etc. so it seems like a vRAM problem to me.
I have an Acer Aspire 5532 running Windows 7 64 bit with 3.00 GB ram and I have 2.75 GB of ram saying unusable. My computer is and has been very slow and I haven't recently added or removed any hardware.I have checked 2 possible problems from info I found on this problem being I've located msconfig, boot, advanced options, max memory is "unchecked" and have checked my bios which do show the correct amount of memory but I can not enable "memory remap" because bios does not support. I've added a resource monitor screen shot below.
I have 6GB of ram installed on windows 7 64-bit ultimate. For some reason I'm noticing that the usage will rise past 50%, but I am unable to find all of the used resources. From what I found, I'm using roughly 3.2GB of RAM when I add up all the memory usage under the processes tab.
My Windows 7 has stopped booting after a restart, the system would just endlessly play the boot animation and not boot properly... system restore won't work, startup repair won't work, chdsk and sfc won't work. I have yet to try and see whether a Registry fix works. Windows loads the WRE VERY slowly.
I know there's an option to "tell" windows to use less memory that it have by configuring the MSconfig. But is there a way to create dual boot with 2 memory configurations? One with 4GB and the second with 8GB?
i have also same this "how to solve problems dumping physical memory to boot" problems .this problem was happen after reboot windows 7 in my hp laptop and also happen before installation.
I have a problem in booting my computer. It is Windows 7 64 bit laptop, from Dell. I have installed Ubuntu 10.04 on my computer separately. When I try to boot my computer, it runs into a blue screen. The blue screen disappears very quickly and then the computer will restart again. I guess the last line of the blue screen is something like physical memory dump.
I tried to boot my computer in safe mode, but it stops at CLASSPNS.SYS. I have also tried to use the startup repair, but in vain. I can't do system recovery because it doesn't have a recovery point. I used the Dell diagnosis tool and ran some tests. It seems that the diagnosis tool can't detect my hard drive. But it is a little bit strange to me because I can access files in my Windows 7 using Ubuntu.
I've just tried to upgrade my PC's memory from 8GB to 16GB and have hit a rather worrying problem in that the PC now refuses to boot. Initially, once I'd replaced the old memory modules with the new ones, I got three beeps on power-up, which I quickly established was the result of my not properly seating the modules. Once I'd made sure they were firmly inserted I tried again, and this time all I get is the computer powering up - so all the lights come on and the fans kick into life - but then it powers down again without even attempting to boot: I don't even get to the BIOS. After a few tries I decided that it might be an issue with one or more of the new modules, so I swapped them back to the original 8GB kit and I still get the same problem. My PC is essentially DOA. Whilst I was inserting/re-inserting modules I did try to avoid and issues with static discharge. I wonder if perhaps I've disturbed a connector somewhere, although I couldn't see any signs of this when I re-opened the case to check.
The new modules are a 16GB Corsair Vengence DDR3 dual-channel 4-module kit (4x4GB). They were replacing a 4 module 8GB DDR3 dual-channel kit (4x2GB), so in both cases all four slots were in use. Motherboard is an Intel DP55WG, which is listed by Corsair as being compatable (16GB is the max for this motherboard). I've been running this system for two years prior to my upgrade attempt this evening, and it's been rock solid with no issues.
Maybe I should reset the CMOS for instance? Note that I'm not a hardware guy, and messing around inside the case isn't something I normally even consider trying... But I thought that this would be a very simple, trouble-free upgrade!
So i have had Windows 7 build 7100 on my laptop for a few months, i was at work and wanted to plug a tv to my vga side port. when i plugged it in, my computer got the blue screen then said physical memory dump
i shut off the computer and restarted it Windows does not boot up any more, it will go to where the Windows icons should fly in, but they never do. It will take me to the startup repair, i tried repairing it but it said it could not.
I tried the system restore from an earlier date but that would crash and say it failed.
I just bought a new Windows 7 DVD; I insert the disc and waited until "Press any key to boot from CD". It took really long time and then it gave an error "Memory overflow error". My windows vista disc is working normally but windows 7 gives error.
