I do a lot of tech support for my family, however I'm a bit stumped a family member presented me with a problem on her hp netbook. She has verizon internet which is dial up and has a belkin router broadcasting the signal. Today however she was unable to connect. Usualy a box would pop up when she would connect to the network or a notification window would come up saying it is connecting to the dial connection. The window did have a box to check or un check asking to do it automaticaly, My question is how would i go about checking the box again and connecting the dial up connection?
I recently received a HP notebook 110 which has a WLAN setup ( I believe this is WiFi). At home I use an older computer, a HP a1000n Pavillion with a 56k internal modem and MSN dialup. Is it possible to set up a WiFi station so I can my notebook can access the Internet? I am posting this here because the notebook using Windows 7, though my Pavilion uses XP. If this is the wrong area, please let me know and I will be move to the correct area.For anybody who wishes to reply, the answers must be complete and with a minimum of jargon so I will be able to understand them.
Suddenly, my direct connected (Cat 5 to the broadband modem) computer is asking me to dial a connection. It no longer seems to know that it is simply connected. When I look at the devices tab, it shows Enabled for my network card and I have tried to reinstall the drivers.I dual boot with Ubuntu and Ubuntu is able to access the internet (and network) fine.
I am using a Dial up connection but when I have to connect dial up connection then I have to change my local area connection ip. Is there any tip or method which is able to my local area connection ip through batch programming/Command prompt ?I need random ips every time before connect from dial up connection. Would it be possible from batch programming.
I have a Dell xps laptop with Win7 home premium. I have a wireless network connection through my netgear, as it shows when open the "network & sharing center." As the screenshot shows, there is an annoying "dial up connection" window that randomly appears while I'm using the pc. I can't access the inter net while this is there so I have to close it
So ive run out of ports on my router (D-Link DIR-825) and my 8 port switch (ASUS GX-D1081). I recently went out and bought an identical 8 port switch. When I try and plug this new switch into my router any device connected to the switch does not receive and IP address. Am I doing anything wrong or forgetting to enable some setting.
I am running Windows 7 Ultimate 32bit. I have a Virgin Media SuperHub, which is both a wireless modem and 4-port router in one unit.
I have my Xbox 360 connected to the hub via Ethernet cable, and connects to Xbox Live perfectly fine. My computer is connected to the hub as well, and connects to the internet perfectly. I have a HomeGroup set up in my network connections, and I am very sure both devices are connected to the same network. However my computer does not recognise the Xbox being connected to the network, and my Xbox does not show the PC as on the network. So they are both connected by cannot find each other.
I have spent hours fiddling around with network settings, my SuperHub is set to allow other devices to connect through it. My HomeGroup has all sharing options turned on, I have disabled my firewall, I have gone through countless forums stating that Windows 7 has alot of network sharing options automatically disabled as default, therefore I have manually run the system settings and enabled all recommended processes etc. I have restarted my Xbox and PC a million times, but they still won't find each other.
My wireless adapter shows that it is connected to my network, but my computer cannot connect to the internet. All other computers can still connect to the internet. It worked fine for almost a year, then one day...no connection.I use Windows 7, Home Premium, 64-bit; engenius wireless adapter and Linksys router. I tried to change to a TP-Link router, but my adapter (or computer) couldn't find it, so I switched back to the Linksys.Tried re-installing wireless adapter, linksys, tp-link; re-sets to both routers; uninstalling software, then re-installing;
This is for my parents house. They have high-speed net that can only be registered to one computer, so running it to a router and then computers is not an option. We used to have it setup with net into "computer 1" then out to the wireless router. The new computer has only one ethernet port, so this can no longer be accomplished without buying another card, which I am very inclined to do. They are getting another computer that will also have Windows 7 and would like to get wireless working again, so...
1) I've tried an ad-hoc connection. I understand the concept and had it working for awhile but found it to be "finiky." I would always have to restart the connection everytime I wanted to use it. I couldn't get it to "stick." Did I maybe do something wrong or is there no way to keep the net connection open? I "saved" the network and set it to start automatically, but it would always close the internet sharing.
2) I haven't messed with home group...will this feature accomplish internet sharing easily??...without messing with any ad-hoc crap? I need everything as simple as possible, so if they have any problems I can fix it over the phone or they can figure everything out for themselves.
Like I said, worst comes to worst, I'll get them another ethernet and run it the old way...was just hoping I could simplify things and save some money.
Before my computer was working fine when i am connecting to the internet using a portable usb internet huawei. Then one morning when i tried to connect i got this "Error: 720".
when I boot up my laptop it takes forever for my laptop to connect to my wireless router. Not sure if it is slow because it is trying to automatically connect or if it takes so long to connect because my OS is still not quite done loading? Does anyone have a suggestion on what to try?
I have a wired linksys router that works fine. I'm not using DHCP on it, its setup at 192.168.1.1. My pc which only has a wired NIC, connects with no problems.I recently bought a tplink wireless router. I changed it so the ip is now 192.168.1.254 (it was 192.168.0.254 originally which meant I couldnt access settings to change from the default password, SSID).
I got the tplink wireless router, so I wouldnt have to be tethered with a wire on my laptop for internet. However, I've wasted time with tech support which I can barely hear or understand.I'd like to get this working, otherwise I'm sending everything back, wireless router and laptop.I can ping both the linksys and tplink from my laptop with no problems.I can get connected to the tplink wireless router without a problem but I cannot get to the internet.
I recently bought a new windows 7 laptop and tried to connect into my my router it did this successfully but it always now says no internet access when i have full bar wireless connection it only works if i am beside the router but if i walk away it doesnt work my other windows xp laptop works just fine even from 30ft away, my windows 7 laptop when troubleshooting the network that there is a problem with the wireless adapter or access point but its a new laptop i also bought a new home hub from bt because i thought that was the problem, it also says when troubleshooting that 'the connection between your access point, router, or cable modem and the internet is broken
I'm having a strange issue with my Windows 7 Lenovo S10 netbook and a friends WEP enabled router. I am able to connect to my home network wr54g linksys on WPA and at the office there's a guest network running (oddly) a 104bit WEP that I can use. However at my friends house I was trying to connect to his DI-524 Dlink router and recevied some very strange (to me) messages.
I'm wondering if Windows 7 has some kind of issue with older versions of WEP and possibly lower encryption? Potentially could it be simply that if we kick up the encryption it will work? I'm fairly confident that if I convince him to kick it to WPA it will work - but where's the fun in that.
I've got a Win 7 64 laptop less than a month old that spontaneously stopped connecting to the internet but says it's connecting to network devices just fine. I first noticed when I attempted to connect to my Verizon hot spot, then I connected to a restaurant's wifi. In both cases it said I had a connection but wasn't connected to the internet. I'm now on my home network trying to resolve and have the same problem. I've uninstalled, rebooted, then reinstalled the driver for the network card. I attempted to install a newer device driver from the manufacturer but it tells me there's no device connected even though I can see it in the device manager and can both uninstall and reinstall it.
When I run ipconfig (and when I look at my router) I can see I'm getting an IP address but again, I can't get on the internet. I've released and renewed the IP address. The device is set to automatically obtain an IP address and DNS servers. I've cleared my DNS cache. I've tried to reinstall TCP/IP v4. I can't ping either a URL or an IP address.
What haven't I thought of? I'm relatively new to Windows 7 so am unfamiliar with it's quirks.
I have an Acer laptop running Windows 7 SP1 64bit. Worked fine until last week. Now will not connect to router.Network centre says ;no internet connection' and 'unidentified network , public network This happens both via wifi and cable connection.I have another router on another line. Same failure messages when I connect the laptop ( wifi and cable)I also have a PC running Windows 7.Connects perfectly to both routers via either method.I an running 'Bullguard' have disabled - no affect.
I am trying to set up WPA security on my new Dell Inspiron Laptop,When I go to "Help and Support" for instructions it says:"The Set Up a Network wizard will guide you through setting up a security key.Click to open Set Up a Network."My problem is when I "Click to open Set up a Network" it only shows my neighbor's router [A Linksys WRT110]. My Netgear WGR614v6 does not show up as an option to connect to.
I have two Windows 7, two win xp (4 in total) connected as file sharing network.1. hen I turn the router off and then on, the win xp computers see all the rest, but Windows 7 computers see no one, they still have the internet ability.2. If I turn on the Windows 7 computers first: the 1st sees nobody, the second sees the first but not the consecutive computers. No home group.
At this moment my PC is wired straight into my modem for internet access. I am however considering plugging it into the router as well in order to access my NAS, enable network printing and what not.The problem that might be is that the router is also providing internet connectivity and thus I will face the problem of having 2 internet connections open.Is there some way for me to tell windows 7 to use the "straight" connection over the router one?. Meaning it will use the straight one to connect to the internet and this not pass that traffic through the router etc.?
I have a Verizon router and I purchased a NetGear N900 wireless dual band usb adapter for my son's computer. I was going to test the N900. It is for college.The N900 will not connect. I do have three other laptops that do connect and work ok. The N900 has WPS but the Verizon router does not.So I have to use the SSID, 'wep' option, and the wep key. The N900 tries to connect and stops trying after about 20 seconds or so. The N900 varies from 4 to 5 green bars. N900 installation was followed and went smoothly and the new software version was used. We are using Windows 7 Home Premium 32bit on my son's computer.I also purchased the Western Digital My Net N750 router for college. I have no way to test everything at home. It does have WPS so at the college I hope everything works.
I have both of these things and my recent internet still come up on my laptop, how can i connect or use my router to get wifi, need this for work asap.
I've just bought a new router-modem (lynksys x2000) to replace my old modem.After going through the setup(by using quick install guide CD-ROM provide with router-modem), i've got no internet connection. My laptop can connect to the router-modem but not the internet.Do my new modem have its own firewall?(I know my laptop firewall is running). Do i need to disable the firewall? If yes, which one should i disable, my laptop of modem.
I have been having a problem with my Desktop for about a week now. It is running Windows 7 Home Premium 64-bit. No built in wireless adapter, but using a USB TP-Link TL-WN722N wireless adapter. The computer can connect to the network, but the internet connection just stopped working. My cell phone, xBox, and Wii can all connect just fine and have internet connectivity. I have already tried:
I have a customer that has just installed a new Dlink N300 router and cable modem internet. He has both a desk top which is hardwired to the router and a laptop which is using the wireless. The desk top does not have any problem with a connection but when he buts the laptop in hibernation it can not find the wireless connection. The odd thing about it is that even though he can not find his own network he can see other networks around him. Any ideas out there on how to solve this issue. This is the second router that we have installed so I am guessing it is not defective equipment.
