I have an Acer laptop running Windows 7 SP1 64bit. Worked fine until last week. Now will not connect to router.Network centre says ;no internet connection' and 'unidentified network , public network This happens both via wifi and cable connection.I have another router on another line. Same failure messages when I connect the laptop ( wifi and cable)I also have a PC running Windows 7.Connects perfectly to both routers via either method.I an running 'Bullguard' have disabled - no affect.
At this moment my PC is wired straight into my modem for internet access. I am however considering plugging it into the router as well in order to access my NAS, enable network printing and what not.The problem that might be is that the router is also providing internet connectivity and thus I will face the problem of having 2 internet connections open.Is there some way for me to tell windows 7 to use the "straight" connection over the router one?. Meaning it will use the straight one to connect to the internet and this not pass that traffic through the router etc.?
I have been struggling with my pc dropping internet connection and not seeing the router as well as it freezing at random times, from 5mins use to several hours, but lately its alot more. Its a cyberpower system machine I bought in oct 2008, its had ALOT of use. See below for system specs below please if needed.It will freeze at all sorts of times, does not matter which application I have open. I have to hard reboot. It will also freeze on shutdown sometimes. I get all sorts of errors on connection loss, it will say the default gatway not available, it will ask me to reset my router too. It resets Local Area Connection adapter all the time, when I try to resolve the issue. It also says "Local Area Connection" doesn't have a valid IP configuration, and resets all my settings back to Obtain IP addresses automatically, as well as Obtain DNS server address automatically in the Internet Protocol Version 4 settings. If I put all the IP addresses and default gateway stuff back in without resetting the router, it then says Troubleshooting couldn't find the problem. Resetting the router usually does work. But not always, sometimes I need a restart. It Sometimes it works if I restart, sometimes it still won't see the router.
I tried putting the IP address in as static, put in the subnet mask, and default gateway.I use the Preffered DNS server IP in there as it helps use network gaming and platforms better like SecondLife.I've tested the router network with same cable I use on another laptop so the cable is fine.Changed ASDL filters twice.Bought new router.I've replaced my harddrive.I've tried two different driver versions for my network card which is a Marvell Yukon 88E8056 PCI-E Gigabit Ethernet Controller I've resit my memory.Tried restoring system to a few days before it started freezing again.I've reinstalled windows a few times now, usually it works for a while (week or two) after a fresh new install. Its a fresh new windows 7 I bought as the machine came with vista.I've manually tried to put in all the drivers I need myself as I don't have the disk that came with my machine. (I have no idea if I've done that right)Sent it in for a service clean and checkup.Turned off the option that windows shuts my network driver down to save on power.
SYSTEM SPEC:
(Left out actual IP address numbers from communication, I have no idea if that is safe to forum lol*) Operating System new - server roles Windows 7 Home Premium (x64) Service Pack 1 (build 7601) Install Language: English (United States) System Locale: English (United Kingdom) Installed: 04/11/2011 00:49:01
I am trying to set up the wireless internet. I am not super tech savvy, however, over the last decade I have been able to research and fix all of my computer problems myself without posting such things. Until now.
I need to set up the wireless router; however, I cannot get the LAN connection to even work with the router.
The error is stating "DNS server is not responding"
I work as a software developer and have had a lot of experience with wireless networking. I have an old wireless router (unsecured at the moment) that I have connected to a modem, provided by Virgin media. When I use a cable to directly connect to the router, all seems fine, but when I attempt to connect wirelessly I am almost immediately presented with "Windows was unable to connect to [router name]". Other people in my house (on both XP and Vista) can connect to the router without any problems, implying that it is a setting within Windows 7. HOWEVER, I am able to connect to another (unsecured) wireless router. I guess this can only mean that there is a setting on the router that is preventing me from connecting...
I do a lot of tech support for my family, however I'm a bit stumped a family member presented me with a problem on her hp netbook. She has verizon internet which is dial up and has a belkin router broadcasting the signal. Today however she was unable to connect. Usualy a box would pop up when she would connect to the network or a notification window would come up saying it is connecting to the dial connection. The window did have a box to check or un check asking to do it automaticaly, My question is how would i go about checking the box again and connecting the dial up connection?
I am trying to set up WPA security on my new Dell Inspiron Laptop,When I go to "Help and Support" for instructions it says:"The Set Up a Network wizard will guide you through setting up a security key.Click to open Set Up a Network."My problem is when I "Click to open Set up a Network" it only shows my neighbor's router [A Linksys WRT110]. My Netgear WGR614v6 does not show up as an option to connect to.
I have two Windows 7, two win xp (4 in total) connected as file sharing network.1. hen I turn the router off and then on, the win xp computers see all the rest, but Windows 7 computers see no one, they still have the internet ability.2. If I turn on the Windows 7 computers first: the 1st sees nobody, the second sees the first but not the consecutive computers. No home group.
I have a Verizon router and I purchased a NetGear N900 wireless dual band usb adapter for my son's computer. I was going to test the N900. It is for college.The N900 will not connect. I do have three other laptops that do connect and work ok. The N900 has WPS but the Verizon router does not.So I have to use the SSID, 'wep' option, and the wep key. The N900 tries to connect and stops trying after about 20 seconds or so. The N900 varies from 4 to 5 green bars. N900 installation was followed and went smoothly and the new software version was used. We are using Windows 7 Home Premium 32bit on my son's computer.I also purchased the Western Digital My Net N750 router for college. I have no way to test everything at home. It does have WPS so at the college I hope everything works.
I have both of these things and my recent internet still come up on my laptop, how can i connect or use my router to get wifi, need this for work asap.
I've just bought a new router-modem (lynksys x2000) to replace my old modem.After going through the setup(by using quick install guide CD-ROM provide with router-modem), i've got no internet connection. My laptop can connect to the router-modem but not the internet.Do my new modem have its own firewall?(I know my laptop firewall is running). Do i need to disable the firewall? If yes, which one should i disable, my laptop of modem.
I have been having a problem with my Desktop for about a week now. It is running Windows 7 Home Premium 64-bit. No built in wireless adapter, but using a USB TP-Link TL-WN722N wireless adapter. The computer can connect to the network, but the internet connection just stopped working. My cell phone, xBox, and Wii can all connect just fine and have internet connectivity. I have already tried:
I have a customer that has just installed a new Dlink N300 router and cable modem internet. He has both a desk top which is hardwired to the router and a laptop which is using the wireless. The desk top does not have any problem with a connection but when he buts the laptop in hibernation it can not find the wireless connection. The odd thing about it is that even though he can not find his own network he can see other networks around him. Any ideas out there on how to solve this issue. This is the second router that we have installed so I am guessing it is not defective equipment.
For the last few days of an evening after downloading large amounts of data using Bit-torrent i.e. 70GB, I keep losing my internet connection. I need to turn my super-hub on and off again, but it will keep losing the connection. I have noticed that if I exit Bit-torrent then I don't lose my connection, but I am not sure whether this is just a coincidence. Is this because of the amount of data I am downloading using Bit-torrent and my super-hub is turning off the connection on purpose or is this something else?
I have been trying to set up a router at my girlfriend's apartment. I first tried a Linksys router that I had brought from home. I hooked it up from the wall port, to the router, to my computer. I was able to access the normal Linksys wireless setup page at 192.168.0.1 and set up a network fine. I then unplugged my ethernet cable and attempted to connect to the network and was not able to. If I recall, it 'connected' but there was no internet connection.
So lately I have been disconnected from the internet every now and then. Usually I just power cycle my modem and router and move on. But today it happened twice so I need to figure out the problem. I powered cycled the modem alone, and I still had no connection. I power cycled the router and I had connection after so I'm assuming it's the router to blame. The router plugs into my modem, and the ethernet cord from the router goes into one of these: Amazon.com: Dynex DX-EHB4 - Hub - 4 ports - Ethernet - 10Base-T - DC power - external: Computers & Accessories. My PC, Xbox and PS3 are all connected to that. Also during this time my iPhone couldn't get internet through WiFi. I have the D-Link DIR-655 as my router.
I have a desktop and laptop with windows 7, I want to use RDC from either side using the internet connection. Both machines are connected with same router for internet connection.
For internet, desktop is connected through LAN cable and laptop through WiFi. Can I use RDC between them without wired connection and using router/internet?
Desktop connected to the internet via usb network adapterThe desktop has a lan card.How can I setup the OS so the wireless internet connection is shared to the lan connection to a router to the router can receive an internet connection.
I recently moved into a new apartment. My roommate has a macbook and an Apple AirPort Express router. She is able to connect to the wireless network just fine, but on my laptop with Windows 7 (x64), the connection is stuck on identifying. I attached the output from ipconfig /all: ipconfig.txt
I'm switching from landline ISP to mobile ISP (dongle). So I'm thinking of sharing 3G dongle (ZTE MF190) internet connection with other PC, device etc, through D-Link modem+router(DSL-2640B) that I use for landline internet connection before. Is this possible? I notice that I cannot use homegroup via D-Link anymore after connecting to 3G dongle. I've tried ICS (internet connection sharing) but to no avail.
Generally once or twice a day, my computer will suddenly drop its internet connection.It will then start an endless loop of trying to connect: Sensing the network is there Trying to connect (With the loading symbol and "Initializing")Appearing to connect successfully (but when I try an open a web page, nothing loads, and I receive an error message telling me there's no connection)A few seconds later, the yellow triangular warning sign appears next to the wireless bar.A few seconds after that, it drops the connection, and then starts over at step oneA few seconds later, it will start again at step one.The only way I am able to get the network back on is to: Disconnect manually (press "disconnect")Turn of my wireless antenna on my computer Turn on and off my router Turn back on the antenna Reconnect.I have to do these 5 steps every time it disconnects.This is only happening on this one computer - other computers on the network aren't experiencing the problem (running XP and Win 7).I have an Asus U56E-BAL7.
Windows 7 home premium 32bit zonealarm basic firewall wlancard dell 1450 usb
Info: the card never had a vista or windows 7 driver. A computer skilled took out a folder from the windows xp installer. Through device manager the folder is installed as driver, and the wlan card works. I wanted to use ubuntu 'remote terminal server'.Connected via pc to pc lan cross over cable. Maybe the connection succeded because ping test was ok. But never made the program 'remote terminal server' work. At a point zonealarm made trouble, allthough disabled. Shutting down computer worked. Error: Next time I turned on the computer, wlan didn't work. The wlan card makes the connection but there is a yellow triangle on the wifi icon in taskbar. Under network it keeps hanging, messaging 'identifying'.I tried this: Reinstalling zonealarm basic. Reinstalling wlan card folder driver. Didn't work.
I have found a wireless connection near me and connected to it. I saw that my speed is kind of good (about 14 Mb/s), I tried to get this speed higher.I went into the router setup from my browser, and changed some settings from thereOnce changed, I reboot the router to see if it changed my speed.The one setting that blocked my access to internet is MCS. I don't remember if that was off/disabled, but i changed it to MCS7, the last option available for MCS... thing.
I have Brother MFC7340 printer connected to my HP home premium Windows 7 64 via a USB port. There is no ethernet connection. I want my Windows XP computer, connected to the local home network via ethernet hard connection through my wireless router to be able to print either with a hard connect or wirelessly to this printer. I am having trouble figuring out what to do and have tried various strategies to no avail.
For some reason my router and modem will not show correctly on my dell inspirion one desktop. Im running windows 7 and here are the net work connection deatils
Connection -specific DNS Belkin Description Realtek PCIe GBE Family Controller Physical Address 00-00-00-00-00-00 DCHP Enabled Yes Ipv4 Address 192.168.2.2 Ipv4 Subnet Mask 255.255.255.0 Lease obtained Wednesday, November 10, 2010 9:45 PM Lease Expires Sunday, December 18, 2146 4:17 AM IPv4 Default Gateway 192.168.2.1 Ipv4 DHCP Server 192.168.2.1 Ipv4 DNS Server 192.168.2.1 IPv4 WINS Server NetBIOS over Tcpip enabled Yes
The Connection was working about ten days ago and then suddenly stopped and read as an unidentified network no internet access. at one point is was not receiving packets but now it is but it still says no internet access on the IPv4 Connectivity. Media state is also enabled and the speed is 100.0 Mbps when i troubleshoot it says windows cant identify problem but in the details it says default gateway is available. when i use the cmd prompt ipconfig/all my local ethernet adapter has a physical address of all zeros.
I have a 3 PC network (no WEP or WPA security) attached to a Thomson 760W wireless router with the latest Firmware (6.3.27.2)2 PCs (Angua and Carrot - dont ask!!) run XP SP3 (all latest updates); 1 PC runs Windows 7 Ultimate (all latest updates)There are no active firewalls,When all PCs have a wired ethernet connection to the network, everything (shares etc) works fine,When the W7 PC is connected to the network wirelessly ,W7 can access the shares on Carrot, cannot access the shares on Angua (). I suspect it cannot even see Angua and the reference is there from an earlier wired connection, cannot access a network drive that points to a share on Angua,Angua can access the shares on W7,A 4th PC running XP SP3 (not a normal part of the network) connected wirelessly can access Angua and can be accessed by Angua and the W7.W7 can ping Angua and the 4th PC (time=1ms)And Angua can ping the W7,I have the same items showing under the Wireless network Connection properties on both Angua and Carrot. They are Client for MS Networks File and Printer sharing QoS packet scheduler TCP/IP Under Network Connction details everything seems to be OK. There is an IP address and NetBIOS over TCPIP says Yes The Troubleshooter (Shared Folders) Couldn't identify the problem' and under details "no issues detected" but attempts to access a share in explorere are met with \Anguafolder is not accessible. You might not have permissions etc etc"(When hooked up wired W7 reports the permissions on the shared folder as, everyone)So it seems that is is something to do with the combination of settings on W7 and Angua,So please, what do I have to do to get the wireless component of this network working remembering that
I have a Dell inspiron mini tower that had some apparently critical either net driver deleted. I'm not entirely sure which driver it was or how to get it back. I've tried downloading a few drivers on another machine and then just transferring them to the bad one but it's not working (3 separate ones now). It was working perfectly before this "thing" was accidentally uninstalled.
