when i plug in a usb 2.0 device into any of the slots, it works perfectly for a while, but then i hear that 'usb device unplugged' sound, followed by 'usb device plugged in' sound. after that, the transfer speeds become miserable, which is why i assume it switches to usb 1.1. i'm using win xp pro sp2 and latest ati drivers for the southbridge
View 4 RepliesI'm connecting my iphone to usb and get the "this device can perform faster...." message telling me to disconnect from the current port and connect to a hi speed port I know which is hi speed port, but cant figure out how to disconnect and then reconnect it
View 3 Replies View RelatedI have installed a Belkin USB 2.0 PCI card in my box (pc only had 1.1 on the board). I have an external WD hard drive that is USB 2.0. When I plug the hard drive into the USB 2.0 port I get a dialog box that says "No High speed USB hub found.... HI-SPEED USB Device Plugged into non-HI-SPEED USB Hub." When I look at my devices, I do not see any USB device that specifies USB 2.0, only the 1.1 device that is built in and the new card whci says "OPTi 82C861 PCI to USB Open Host Controller".
I have unistalled ALL USB devices and reinstalled, and still the same. I am running XP Pro , with SP2. The device manager shows no errors and reports that all devices are working properly. I have checked with Dell and there is no new Bios for my pc (Dimension 4300). Everything I have read said XP should support this card without any additional drivers.
1.Can you tell me, how to access to device manager if i set hard disk to another computer as slave?
2.how to make network browsing faster(in local area network)because there is more than 2-5 minutes to access to another computer(in win xp)
Motherboard Epox EP 8KDA 3J
OS XP SP2 Home E
AMD 3000+ CPU
Memory Upgrade
Original setup Had two 256 Rosewill DDR400
one open slot
INSTALLED 512m ampo D400 35145588-P-R
Into Slot #1
PC Ran OK with 512 Ram
Installed one of the Rosewill DDR400 256
into Slot #2
PC Ran OK with 768 Ram
Installed Rosewill DDR400 256
into Slot #3
PC would not Boot
Does not seem to recognize 3rd Slot
I was told by Lenovo that one slot will accomodate 1 gig of memory, instead of using 2 half gig sticks.I was also told about something called "memory boost" as an external memory source to increase memory. has anyone heard of this? I want to run PhotoshopCS and need 1 GIG of memory and don't want to get new motherboard(the machine is long out of warantee).
View 1 Replies View RelatedThis is the strangest thing I've seen in the past 10 years of using computers. I have an Acer Aspire 7535-5020 laptop that came with windows 7, but I'm very picky and I wanted Windows xp back so I went onto Acer's website and downloaded all of the windows xp drivers and then formatted the laptop to Windows XP with intergrated Service Pack 3.The computer works just fine except for one very strange oddity - the USB mouse I'm using only works when plugged into the first USB slot, it will refuse to work in the other 3 USB slots.I'm using a Microsoft Intellimouse Explorer 3.0 USB which is my favorite mouse and I have 3 of them at home. When I was formatting the laptop
View 3 Replies View RelatedI have just purchased a Campaq Presario laptop v3607TU. It came with only "FreeDos" installed. If I boot up, it goes to the c prompt, and I can see call the directories on the hard drive. inserted my Windows XP bootable disk into the CD/DVD slot, and restarted. It booted from the CD, and the setup files begin to be read. Then I get a message that says, Setup cannot find any hard drives on your computer. The only option is F3 QUIT.
View 11 Replies View RelatedHow do I find my processor speed, RAM, and hard drive speed/configuration?
View 3 Replies View RelatedI am using a DSL connection with a maximum download speed of upto 2MBPS but i usually recieve it for about 1-1.5MBPS. I have tried using Download Accelerator softwares to increase my speed but wuth those some spam also come into my computer so i am not using it anymore. Is there any way by which i can increase my internet speed by doing some changes in Windows internally. Also while using sharing sites my speed tends to fall to about 45KBPS.
View 14 Replies View RelatedHow can i Boost up my PC speed and downloading speed,Although i used some Optimizers but it also occupy my disks memory spaces and speed down the OS similarly for Booting Time.
View 9 Replies View Relatedi want to speed up my Network file transfer as fast as "whatever"is there any way that i can do using script or software or anythin Local area connections speed: 100 Mbps
View 1 Replies View RelatedInsert any USB device to this computer, Computer keeps restarting and it wont stop doing that until I remove the usb device. I tried with all the usb ports on this computer and problem is the same. Even by hooking up a usb keyboard or mouse, computer wont get to the login screen. it keeps on restarting. It wont even go into 'safe mode'.Anyone have any clue whats going on and the solution to fix it?
View 2 Replies View RelatedI have an AMD 2.1 athlon, i try and re-install my C-MEDIA AC97 Audio Device, i dont have the CD and i dont know how to fix this
View 1 Replies View RelatedI have installed a targus 7 port powered USB HUB on my computer. Device manager reports unknown device. I have deleted and it restalled the drived after the system rebooted. Device manager still saying unknown device. Their is not driver needed according to the manufacture. When the PC is booting it does see the IPOD mini and the Flash drive. But once the PC is fully out and login and I look a the device manager is still reporting unlnown device error (code 10).
View 1 Replies View RelatedI had some trouble last night and today with getting rid of a virus. Now that it is gone, I am having sound problems (maybe related, maybe not). This morning, when I opened iTunes I got a message that there was no audio device detected. After trying several things, I rebooted. Magically, I could play music again. However, a short while later, I again got an error message telling me that there is no audio device found, even though it shows up in Device Manager as working properly. The problem goes away for a short time after I reboot, but returns. It is Realtek AC 97. Why won't my computer keep recognizing it? (It tried going to Realtek's site to download an update. It has updates for Windows 98, 95, etc., but not for XP. Or at least I couldn't find it.)
View 6 Replies View RelatedRunning Windows XP on Emachines ET1161-07. Installed all drivers that I could find, since EMachines does not represent XP. Tried Realtek audio and HD audio, tried Intel, didn't work. Tried NVidia, as it has an NVidia motherboard. Spent too much time on this computer. Can anyone lend a hand? I know it's got something to do with Audio, as there's no audio device detected in Sounds, under Control Panel.Customer has to have computer today.
View 10 Replies View RelatedI gotta a XP Home SP2 Machine was running fine then on boot up sound device not found. went to device mng and no items displayed. System restore had been didabled and Norton disabled as well. Done a spyware scan pull nout so did virus
View 3 Replies View RelatedI've been using a Buslink 40G disk-to-go for about 2 years and love it. Today I plugged it into the USB port and the drive did not display. I've searched forums half the night since this drive contains financial data that hasn't been backed up for a month (yes, bad practice, I know) and I need to get it working. I've uninstalled, reinstalled, updated drivers, removed and reinstalled drivers, rolled back drivers and tried everything short of bios changes I've seen recommended.
View 1 Replies View RelatedI had this problem last time when I fresh installed Windows XP Pro on my computer. I don't know the time, but it happens at least 30 days after I reinstall the OS and software. Today, my computer prompted me to install drivers for a PCI Input Device, but I haven't installed any new hardware for months. Basically, I haven't touched the inside of my computer for that long. So why is Device Manager prompting me to install this mystery device? Hardware ID shows that it is from vendor 1102, which is Creative, and I have an Audigy 1. Also, my FireWire port is Code 10, the device cannot start. So I'm thinking the mystery device is the same firewire port. But why show up as a separate device? I tried removing the devices and restarting the computer, but they return to haunt me again. The device properties for the PCI Input Device says PCI SLOT 7, AND I DONT HAVE A 7th slot! Can someone help me, please? Device manager shows my 1394 Net Adapter with a yellow exclamation, and it has code 10, device cannot start. There is an unknown device, the PCI Input Device, which doesn't allow me to install any drivers for it, yet it has the creative Vendor ID 1102. It shows itself as being PCI Slot 7.
View 3 Replies View RelatedI have a feeling that this is simply a case of some registry settings which need adding/modifying/deleting but exactly which ones and what values I do not know. No, I haven't tried re-installing XP.
View 3 Replies View RelatedThe system seems to be very stable at this point in time. I run Norton Utilities and other maintenance sw as well as have a firewall/pest remover/anti-virus. Behavior - most things work fine on the USB ports, either the hub or direct connects. One digital camera will only work when direct connected(not thru the hub). I have a scanner that will only work on a 2003 Compaq Presario, but not on the whitebox on any port. Also, I have had two devices that won't work at all. I have noticed that the USB mass storage device icon doesn't seem to be present now when I attach a flash drive. This is recent behavior and doesn't predate every USB problem.
View 4 Replies View RelatedLast night I installed ATiTool 0.24 over my 0.25 version (stupidly). I also did a BIOS update and installed Cat6.3 and then AVIVO converter. When I rebooted, I had this new PCI device requiring a driver,but it's an unknown device and doing an auto update helped me.I can't get rid of this pesky PCI device (tried uninstalling but Windows detects it again after restart/boot-up). All my stuff is working, so I don't know where this critter came from?
View 1 Replies View RelatedI have a huge problem with two unknown devices in my "Device Manager" after formating and reinstalling fresh copy of Win Xp Pro.In my "Device Manager" there is two lines with Unknown devices.
View 10 Replies View RelatedI'm using XP SP3 Home Gateway desktop My device Manager has nothing in it. I don't know when it quit showing. I have checked Bios plug&Play, and it is set in Auto. I am also getting an error stating my recovery D: is running out of disk space.
View 2 Replies View RelatedMy computer cannot detect any cd's in my DVD or CD drive. When I open Device Manager the CD/DVD devices have an error. This error: Windows successfully loaded the device driver for this hardware but cannot find the hardware device. (Code 41) Click Troubleshoot to start the troubleshooter for this device.When I run the DriverScan it simply doesn't even have an entry for the drives, probably since it thinks it doesn't even exist at the moment.
View 5 Replies View RelatedAnyone know how I can rename a device in device manager, (or the registry), so it doesn't show #2 after the device.I used the leadtek driver uninstall tool last night. And it removed the drivers I had for this Leadtek Deluxe tuner alright.BUT it also renamed my onboard Gigabit LAN (onboard) to #2 my scanner to #2,
and removed my Nvidia drivers for the video card.And reverted the videocard drivers to MS Nvidia drivers.I managed to fix the scanner entry by uninstalling the drivers, then rebooting and reinstalling the drivers.And I managed to fix the videocard drivers, by reinstalling the Nvidia drivers.So, yup, anyone have any idea how I can change the board LAN, so it doesnt have #2 after it? sing XP Pro SP2
the other day I tried to insert my friends usb into one of the frontal usb ports, it said it couldn't recognize the device or that it had malfunctioned. From that point on, Anything connected to the pc via the usb won't be recognized. everything else on the pc works fine, so theirs either some really easy way of fixing this or i need to buy a new motherboard/serial bus.
View 1 Replies View RelatedI bought a WD Passport 160gb. and it worked fine I left it running on my computer for 2 weeks and now its not working error (USB Device does not recognize device) so I thought I broke it, I went out and bought another one and I am getting the same error with the new one and old one, on mulit computers that it worked on in the past, I even tried in on new computers.
View 37 Replies View RelatedThis has happened several times and I don't know how to correct it, if anyone has a suggestion please let me know. When I uninstall. unplug and remove drivers, for a USB device (web cam) and then reinstall it later Windows says it #2 or #3 or #4 but there is no other device. Why does it name it that way and how can I make it install as just that device.This has also happened when I installed a replacement NIC card.I hope someone understands what I am trying to explain.
View 1 Replies View RelatedI haven't installed anything new on my computer but today after having my computer shipped to me via UPS I cut on my computer and where the XP load bar screen was I got: "reboot and select proper boot device or insert boot media in selected boot device".Seeing this I knew I went into the BIOS setup and tried to turn the system priority to look at the HDD. Instead I only had the option of the DVD drive and the CD drive.I have no idea how to solve this problem and don't have any of the recovery CD's. I DO NOT WANT TO REFORMAT because like a bad little boy I did not backup my 4 years worth of work.
View 9 Replies View Related