Independent Dual Boot capabilities on two separate & independent drives, one on the MOBO EIDE controller the other on the VIA SATA RAID Controller on the same MOBO. I am attempting a clean installation of Windows XP on the SATA Drive but the system fails to recognize even the presence of the drive. This, even after stripping the system of all drives except this one, and after 'prepping' it to be bootable with MAXTOR prep. tools.Was there ever a restriction on putting an O/S on SATA drives even on the MOBO? I have all the updates installed, "I think".
I'm can't get WinXP installation to find my Sata Hard-drive. I'm running Suse Linux on my IDE-HD and I could also had no problems getting my Suse 10.1 installation to install on the SATA-HD. I've booted up with winxp media install disk and tried to use the F6 key at the right time but nothing happens so it keeps going until I get to the point where I can press the S key to install SATA RAID driver from disk that came with my motherboard. The drivers install but then windows install still says no disk to install windows... I don't get it.
I've checked my bios and SATA in there, in fact the first thing I see when I boot up in the boot sequence is the SATA drive. Linux knows it's there but windows install doesn't. I installed XP on a WD SATA drive before and all I had to do was press F6 to install the controller from the XP disk but that doesn't work now.
i have a system that is running xp and i need to format the hard drive due to a new mobo. in the past i have tried and i ran into a problem that you already have an os installed. what is the best way to format in xp?
I have been trying to dual boot my Vista Ultimate system and XP, the problem I run into is that once I get the XP partition, put in the XP boot disc and restart the system the XP install starts. It loads the drivers that it needs for the install but then I get the blue screen saying that windows has shut down to protect the computer. I do have a SATA drive and I've heard this causes issues but I haven't heard of one exactly like mine before (I never get to the actual installation just the pre-loading).
recently bought SATA 3.0 hard disk(samsung)and i forgot if my motherboard support this hard disk,after checking it only supports 1.5 SATA.I visited samsung website on how to force my Hard disk to run at 1.5
Isn't the problem going from vista back to xp an sata driver problem? If you would disable sata native mode then boot from the xp cd it should show the hard drive and any partitions. The biggest chore may be getting the drivers needed for XP and if is a laptop they rarely come with a floppy drive, so during the xp install I don't know if after you press F6 if you can remove the xp cd and put in a cd that you burned the needed drivers to if a floppy is not available. People should have the freedom to choose whatever operating system they want without all of the headaches
I've got this old mobo Abit VT7. I want to install XP on it. However, the XP disc doesn't recognize SATA hard drives. So I downloaded official SATA driver from the Abit website http://tinyurl.com/kua5qz and tries to slipstream my XP disc following the instructions set forth here http://tinyurl.com/37anvn . I am not too clear how to incorporate the drivers from the official drivers, but Nlite seems to be able to find the drivers once I pointed it to the top unzipped driver directory, and I selected the XP folder for it. However, the newly created XP disc still fails to recognize the SATA hard drives. Alternatively, I believe I could have a boot floppy which would load the drivers in, then I launch the setup in the XP installation CD via command line. But I don't know how to create a boot disc which has those SATA drivers in.
I installed a Serial ATA hard drive. Booted from floppy,partitioned and formatted 120mb HD,with 2 partitions.
Connected my old IDE drive and booted from Norton Ghostdisc, cloned my old drive to the new one. Removed all drives and USB card readers except the new SATA drive. Windows will not fully boot, it halts at the blue Windows intro screen. Restarted Windows, and scandisk ran, but indicated drive letter "H" not "C", so I guess the windows installation is still looking in the original place for it's files, ie. the "C" drive, that's why it won't boot. You cannot change the "System" drive letter from "Computer Management" within XP, and I cannot get into Windows anyway. Is there a "work around" for this, other than a clean install? Even then, is it still going to be drive "H"? And that means another Windows activation. How many goes do you get for activation? I tried a windows repair installation, and reactivation (wasted). Windows then worked, sort of. Lots of things were missing and programs unuseable,as they were looking for their files on "C": so I went back to square 1, put my old drive back in for the moment
I recently bought a new system with XP home already installed. Now I find that I should have installed the new SATA hard drive for better perfomance with my new P4 dual layered processor. I have ordered the new SATA 80 GB drive and would expect that when I install the XP on it I will have to call microsoft to activate it on the hard drive (since it was originally installed on the hard drive that I got with the new system). Any issues here or just call and explain the upgrade during the activation? (Understood that I will have to reinstall my other software again) As a follow up to this, would there be any problem slaving the original drive on the same IDE ribbon as the new SATA drive?
I was wondering if it makes any sense to buy and install a SATA 300 controller to work with two WD SATA 300 drives. I kind of doubt I will achieve 300mb buffer to host transfers with only SATA 150 motherboard.
I cannot install Windows XP onto a SATA hard drive. I read that I need to install the drivers for the HD separately during the Windows installation but how do I do that.
I can't install Windows to the SATA drive. It loads everything it needs, then when it tries to boot, it says the files aren't found. I'm guessing it can't read it without the drivers installed, but how do i do that with no OS? I was thinking of dual booting with linux.
a few days ago i had a problem performing a clean install of Windows XP which is on another thread Link below: URL...I now have managed to install XP on my 60GB drive but when i try to format my 400gb SATA drive i cannot. BIOS Sees my SATA drive and windows XP sees the drive as Unallocated. I tried formatting it in windows and Partition Magic 8 and both times windows seems to crash and hangs and there is nothing i can do but reboot to get back into windows.
I have a pc with 2 hardrives that has been working for quite a while now. One drive is IDE and another is a sata drive. the sata drive has a partition in which windows xp is installed on. Now its time to format this computer and give it a fresh new start, but then I start the windows set-up from the boot disc it doesnt detect the sata drive.
I have an HP Media PC M400Y. It is a P4 3.0 Ghz with 1GB ram. It originally came with MCE2002. Last week I upgraded to MCE2005 to use the media extender feature with my new X-box 360. Here is the problem and some background.
About a year ago, I had installed a second SATA hard drive, Seagate Baracuda 300GB, model ST3300831AS. This drive was plug and play into the motherboard and never had any issues. Before reformating the main C: drive, I moved all my valuable data on the SATA drive.
I then turned the PC off, removed the power and signal cables from the SATA drive. (I'm a novice, and didn't want to take any chances of erasing the SATA drive, while reformating the main C drive)
i have a hp compaq dc7100 it has a sata hard drive in it, i need the drivers for it, not able to load xp on in locks up, i do not have the drives, i checked with hp not able to find.
Just bought a 300Gig Maxtor SATA hard drive. My supports the connection onboard. How do I get Windows XP pro to reconized the full 300Gigs and not just 137Gigs. I have a Intel(R) Desktop board D85GVHZ Base System Intel(R) Celeron CPU 3.06Hz 512MB of ram.
I have recently bought a new computer that came with windows vista as you may have guessed the experience mostly has not been a good one, with lots of compatibility issues. I want to dual boot Vista with XP but the problem is I have heard windows XP does not have the SATA drivers on the disc. I understand that you just need to insert a floppy and push F6 I think but the problem is I don't have a floppy drive! Is there anyway I can slipstream the drivers into the install or something?
I wasn't sure where this thread should be placed. I want to install XP and it wouldn't detect my hard drive. Since I have no floppy drive I want to slipstream a xp cd with the drivers already there. I am using the program nLite to make the bootable disc. However the problem is that I can't find the drivers or i'm unsure what is correct. My controllers are... Intel(R) 82801HEM/HBM SATA AHCI Controller Intel(R) ICH8M Ultra ATA Storage Controllers 2850.. But chipset is Mobile Intel(R) 965 Express Chipset Family.
My motherboard died and I had my files password protected in Windows XP Media Edition, can I connect the SATA hard drive to another PC via USB and unlock the protected files, or does it have to run as the main drive to allow access and entry of password and then making all files public?
I'm running a sata hard drive and cannot use ide drive .I have a MSI neo2 7025 board i installed a 36gig10,000 sata drive and made it my main drive and wanted to use 250 gig drive as slave but when i hook it up the computer will not fire up . so i went to set up and look for the ide drive and it did not show any ide drives.
So I was bored today and began creating a old Pentium 4 System out of old PC parts around the house.Now, I have assembled everything and have tested all the parts and all are working fine, However when I go to install Windows XP on the machine it will not detect the Hard Drive (On the Partition Screen). Now I thought it may be a hard drive problem so I connected the hard drive up to my current PC and ran the XP Installation fine.However, Now when I try to boot the XP I installed on the hard drive off of my other system it will get to the splash screen and restart, so I turned off automatic restart on system failure and I get the 0x0000007B Stop error.
So I retried the XP installation on the system again, got to the Partition and Hard Drive selection screen and still no Hard Drive to be seen, I plugged in a USB and it detected it fine.I have tried booting in safe mode & every option under F8, However it just restarts on the XP splash screen, And as I said the hard drive seems fine as it comes up in bios and my main PC ran it fine, So I'm beginning to think that i'm in need of my motherboards SATA Drivers or something.
I have an 160 Gb wD hardrive set to master on my Asus P4p800e deluxe mother.....I would like to know If I could add an extra hardrive sata as a slave...The reason for this is becuase I want to keep diffrent files in here...But I don' know id this could be done...Do I need to dual Boot and install the same Operating system in the Sata...I know my motherboard supports sata Ide and Raid disks...and if its not possible ...Can you tell me another way to add a second drive without dual booting,...I just want my drive to appear in my computer so I could save different files
I have integrated the drivers onto the windows xp home disk using nlite as well as integrating sp2 but after the restart it keeps saying failed to load os, why should I do to install it on my sata drive? this is making me consider consider vista, does vista install to sata drives straight from the disk?
Doing a fresh install of xp on a sata drive. When it asks to press F6 to install the third party drivers will I be able to load off the motherboard driver cd, or does it *have* to be a floppy.? Reason is the folder that contains the driver info on the cd is over 6mb so obviously won't fit on a floppy..and I'm not sure which I need to complete the install. If I habe the driver cd in the second cd drive will I be able to browse to it when asked? Failing that, just what info do I need to put on a floppy?
I'm not completely computer illiterate but i have never set-up a dual or triboot system before.I want to triboot XP Pro, Vista Home Premium and Ubuntu. I have a brand new 500GB SATA hard drive which is straight out of the box. I don't have vista yet but plan on getting it soon (when the next service pack is released) and don't want to have to reformat my hard drive when i do. So i thought it would be better to prepare for it now
installing xp on a sata drive as windows xp wont see the drive i know i need the sata drivers but cant find the rights ones for my board its gigabyte g31m-es2l chipset g31 express
I just bought me a new SATA 250GB Hard Drive and a external hard drive enclosure. I received the items today and I just realize the hard drive enclosure doesn't build into the way to connect to the SATA 7-pin data connector. All it has is the Parallel ATA 40-pin data connector. Can anyone recommend any external hard drive enclosure that can connect to SATA connector directly. And there is a main reason why I choose a SATA hard drive.
I'm trying to install Windows XP on my new Serial ATA hard drive, it has been formatted everything seems ok, When I start installing windows XP pro on this machine it seems like it just can't detect the damn hard drive, when I set it as boot on te serial ata drive eeverything works fine, it goes as C:/ but I just can't switch to my cd drive with windows XP to install it.When I boot up my other hrd drive with windows xp, I can actually see my hard drive in windows explorer.
I want to install Windows XP on a new SATA HDD drive. The computer in question came with Windows Vista installed. There is no IDE option in the BIOS. There is no floppy drive on the unit. So it looks like I might have to slipstream all the drivers, etc., on to the unit (which I have no clue how to do). I do not have the motherboard make or model number, nor do I have the motherboard CD. My business partner is trying to take the cover off the laptop as we speak, but we're having trouble getting it off. Thus, as of now, we can't identify the motherboard manufacturer or the serial number.
Can anyone here point us in the right direction? The computer in question is a Compaq Presario c769us (laptop). It was purchased in June 2008. This all started when my business partner decided to use a Vista System Recovery CD to overwrite the existing copy of Vista that he had on the computer. After he ran the disk, the system stopped working. So right now, we have the old hard drive, which contains a non-working copy of Vista on it (which we can 't delete), and we have the new hard drive (a 250 GB Hitachi). So maybe we could just delete the copy of Vista on the old hard drive - the self drive test checked out okay on the old hard drive. So I guess the two options are - figure out a way to put XP on the NEW hard drive, or figure out a way to put XP on the OLD hard drive and delete Vista from it first. If we can put XP on the old hard drive and remove Vista from it, we could take the new hard drive back, and get our money back, too.
