I'm running a sata hard drive and cannot use ide drive .I have a MSI neo2 7025 board i installed a 36gig10,000 sata drive and made it my main drive and wanted to use 250 gig drive as slave but when i hook it up the computer will not fire up . so i went to set up and look for the ide drive and it did not show any ide drives.
View 7 RepliesI'm getting extremely frustrated with a problem I keep encountering trying to install a new SATA Hard Drive. I connect the SATA HD power & data cable I prepare a FDD with the necessary HD Cotroller Drivers from the motherboard utilities CD I boot the PC I insert my XP Pro (SP2) CD The PC boots from the CD I press F6 when prompted for 3rd party drivers When prompted, I install the necessary drivers from the FDD I then get to the bit where I chose to install Windows rather than do a Repair - when I select install, I'm told that no HD is present & that I need to exit by pressing F3 I've tried removing RAM to see if any is dodgy but still encounter the same problem.
I've attached the new SATA HD to a different PC & everything moves on perfectly but I quit before formatting the drive as I want to do a clean install on the other PC. I'm beginning to think that there might be a problem with the Motherboard but am open to suggestions (the old HD is stuck in an infitinte boot loop & am unable to slave it to another HD as it wont respond - maybe caused by a Motherboard problem?).
After my last hard drive took a nosedive, I went out and bought a Western Digital Serial ATA 500 gb harddrive. I've physically put it in my Sony Vaio Desktop. I am trying to install Windows XP Professional now. When I get to the Setup screen is says Unknown Disk. I've already seemed to install the drivers for the new harddisk (they provided me a CD to install the drivers, it came with a program called "Lifeguard Tool" or something like that.
I have tried pressing F6 to install a RAID driver using the Windows setup... I pressed S... but then I find out I need a floppy disk drive... even if I had one, the box only came with a CD and not any floppy disks. I've tried slipstreaming Windows xp cd, service pack 2, and the drivers onto one bootable cd, it did not work... i'm too tired to go in there and find out why. *sigh*
I recently bought a WD 74GB Raptor harddrive to install XP on, but I'm having problems. Every time I load up XP setup from the setup CD, when it gets to the part where the installation options menu is about to appear, as it tries to boot windows from the CD, I get a BSOD and have to restart. I've tried running the CD with my other 80GB WD IDE hard drive inside and it doesn't cause this stop error. I've been screwing with this for 2 weeks now trying everything I can find on google and forums to fix this problem. I have the correct SATA drivers for my board as well for the drive of which I hit F6 for at the beginning of setup.
View 1 Replies View RelatedI am copying a hard drive from an old computer, I don't have the computer, just the hard drive. I am using an SATA/IDE to USB 2.0 adapter. The problem is, when I try to copy the files, it wont let me because it says I don't have the permission. I change the security settings and it still wont let me open the documents or files.
View 2 Replies View RelatedI installed a Serial ATA hard drive. Booted from floppy,partitioned and formatted 120mb HD,with 2 partitions.
Connected my old IDE drive and booted from Norton Ghostdisc, cloned my old drive to the new one. Removed all drives and USB card readers except the new SATA drive. Windows will not fully boot, it halts at the blue Windows intro screen. Restarted Windows, and scandisk ran, but indicated drive letter "H" not "C", so I guess the windows installation is still looking in the original place for it's files, ie. the "C" drive, that's why it won't boot. You cannot change the "System" drive letter from "Computer Management" within XP, and I cannot get into Windows anyway. Is there a "work around" for this, other than a clean install? Even then, is it still going to be drive "H"? And that means another Windows activation. How many goes do you get for activation? I tried a windows repair installation, and reactivation (wasted). Windows then worked, sort of. Lots of things were missing and programs unuseable,as they were looking for their files on "C": so I went back to square 1, put my old drive back in for the moment
I recently bought a new system with XP home already installed. Now I find that I should have installed the new SATA hard drive for better perfomance with my new P4 dual layered processor. I have ordered the new SATA 80 GB drive and would expect that when I install the XP on it I will have to call microsoft to activate it on the hard drive (since it was originally installed on the hard drive that I got with the new system). Any issues here or just call and explain the upgrade during the activation? (Understood that I will have to reinstall my other software again) As a follow up to this, would there be any problem slaving the original drive on the same IDE ribbon as the new SATA drive?
View 7 Replies View RelatedI was wondering if it makes any sense to buy and install a SATA 300 controller to work with two WD SATA 300 drives. I kind of doubt I will achieve 300mb buffer to host transfers with only SATA 150 motherboard.
View 6 Replies View RelatedI cannot install Windows XP onto a SATA hard drive. I read that I need to install the drivers for the HD separately during the Windows installation but how do I do that.
View 3 Replies View RelatedI can't install Windows to the SATA drive. It loads everything it needs, then when it tries to boot, it says the files aren't found. I'm guessing it can't read it without the drivers installed, but how do i do that with no OS? I was thinking of dual booting with linux.
View 2 Replies View Relateda few days ago i had a problem performing a clean install of Windows XP which is on another thread Link below:
URL...I now have managed to install XP on my 60GB drive but when i try to format my 400gb SATA drive i cannot. BIOS Sees my SATA drive and windows XP sees the drive as Unallocated. I tried formatting it in windows and Partition Magic 8 and both times windows seems to crash and hangs and there is nothing i can do but reboot to get back into windows.
I have a pc with 2 hardrives that has been working for quite a while now. One drive is IDE and another is a
sata drive. the sata drive has a partition in which windows xp is installed on. Now its time to format this computer and give it a fresh new start, but then I start the windows set-up from the boot disc it doesnt detect the sata drive.
I would like to know if I can copy my whole hard drive to a backup hard drive. What I would like to do is buy a new hard drive for my laptop. Then move all and I do mean everything windows XP etc. to the new hard drive. So that I could the start using the new hard drive just like the old hard drive. I think my old hard drive is going bad.
View 7 Replies View RelatedI just purchased a new hard drive and when I boot to the XP Pro CD I press Enter to install XP but I get the following screen. "Setup did not find any hard disk drives installed in your computer". This is the only hard drive in the system.
When it first boots up I see Award Modular BIOS v6.00PG then it detects the Main Processor then detects IDE Drives GigaRAID BIOS V1.36 F/W Ver 02093030 it detects the new hard drive in Drive 1 - IDE 1 then siI 3112A SATALink Host Controller Bios Version 4.2.00 It doesnt find a primary drive
I have an HP Media PC M400Y. It is a P4 3.0 Ghz with 1GB ram. It originally came with MCE2002. Last week I upgraded to MCE2005 to use the media extender feature with my new X-box 360.
Here is the problem and some background.
About a year ago, I had installed a second SATA hard drive, Seagate Baracuda 300GB, model ST3300831AS. This drive was plug and play into the motherboard and never had any issues. Before reformating the main C: drive, I moved all my valuable data on the SATA drive.
I then turned the PC off, removed the power and signal cables from the SATA drive. (I'm a novice, and didn't want to take any chances of erasing the SATA drive, while reformating the main C drive)
i have a hp compaq dc7100 it has a sata hard drive in it, i need the drivers for it, not able to load xp on in locks up, i do not have the drives, i checked with hp not able to find.
View 5 Replies View RelatedJust bought a 300Gig Maxtor SATA hard drive. My supports the connection onboard. How do I get Windows XP pro to reconized the full 300Gigs and not just 137Gigs. I have a Intel(R) Desktop board D85GVHZ Base System
Intel(R) Celeron CPU 3.06Hz 512MB of ram.
I have recently bought a new computer that came with windows vista as you may have guessed the experience mostly has not been a good one, with lots of compatibility issues. I want to dual boot Vista with XP but the problem is I have heard windows XP does not have the SATA drivers on the disc. I understand that you just need to insert a floppy and push F6 I think but the problem is I don't have a floppy drive! Is there anyway I can slipstream the drivers into the install or something?
View 2 Replies View RelatedI wasn't sure where this thread should be placed. I want to install XP and it wouldn't detect my hard drive. Since I have no floppy drive I want to slipstream a xp cd with the drivers already there. I am using the program nLite to make the bootable disc. However the problem is that I can't find the drivers or i'm unsure what is correct. My controllers are... Intel(R) 82801HEM/HBM SATA AHCI Controller Intel(R) ICH8M Ultra ATA Storage Controllers 2850.. But chipset is Mobile Intel(R) 965 Express Chipset Family.
View 7 Replies View RelatedMy motherboard died and I had my files password protected in Windows XP Media Edition, can I connect the SATA hard drive to another PC via USB and unlock the protected files, or does it have to run as the main drive to allow access and entry of password and then making all files public?
View 1 Replies View RelatedWhat is the best process to reformat my hard disk? it is SATA.. i will use winXP.
View 8 Replies View RelatedSo I was bored today and began creating a old Pentium 4 System out of old PC parts around the house.Now, I have assembled everything and have tested all the parts and all are working fine, However when I go to install Windows XP on the machine it will not detect the Hard Drive (On the Partition Screen). Now I thought it may be a hard drive problem so I connected the hard drive up to my current PC and ran the XP Installation fine.However, Now when I try to boot the XP I installed on the hard drive off of my other system it will get to the splash screen and restart, so I turned off automatic restart on system failure and I get the 0x0000007B Stop error.
So I retried the XP installation on the system again, got to the Partition and Hard Drive selection screen and still no Hard Drive to be seen, I plugged in a USB and it detected it fine.I have tried booting in safe mode & every option under F8, However it just restarts on the XP splash screen, And as I said the hard drive seems fine as it comes up in bios and my main PC ran it fine, So I'm beginning to think that i'm in need of my motherboards SATA Drivers or something.
Independent Dual Boot capabilities on two separate & independent drives, one on the MOBO EIDE controller the other on the VIA SATA RAID Controller on the same MOBO. I am attempting a clean installation of Windows XP on the SATA Drive but the system fails to recognize even the presence of the drive. This, even after stripping the system of all drives except this one, and after 'prepping' it to be bootable with MAXTOR prep. tools.Was there ever a restriction on putting an O/S on SATA drives even on the MOBO? I have all the updates installed, "I think".
View 6 Replies View RelatedI have an 160 Gb wD hardrive set to master on my Asus P4p800e deluxe mother.....I would like to know If I could add an extra hardrive sata as a slave...The reason for this is becuase I want to keep diffrent files in here...But I don' know id this could be done...Do I need to dual Boot and install the same Operating system in the Sata...I know my motherboard supports sata Ide and Raid disks...and if its not possible ...Can you tell me another way to add a second drive without dual booting,...I just want my drive to appear in my computer so I could save different files
View 8 Replies View RelatedMy computer came with a 80gb HD with windows xp pro.. I had took a 180gb hd from another comp. that was running windows xp home and connected it as a slave drive. A window popped warning me that vital info. would be deleted in order to format/ partition the second drive (180gb HD). Was this a mistake doing it in this manner? If not...How would I go about using the whole "180gb" and not just the 35gb it's only allowing me to use. And is there any way to move files so that they will be protected?
View 2 Replies View RelatedI have integrated the drivers onto the windows xp home disk using nlite as well as integrating sp2 but after the restart it keeps saying failed to load os, why should I do to install it on my sata drive? this is making me consider consider vista, does vista install to sata drives straight from the disk?
View 1 Replies View RelatedDoing a fresh install of xp on a sata drive. When it asks to press F6 to install the third party drivers will I be able to load off the motherboard driver cd, or does it *have* to be a floppy.? Reason is the folder that contains the driver info on the cd is over 6mb so obviously won't fit on a floppy..and I'm not sure which I need to complete the install. If I habe the driver cd in the second cd drive will I be able to browse to it when asked? Failing that, just what info do I need to put on a floppy?
View 4 Replies View RelatedI'm can't get WinXP installation to find my Sata Hard-drive. I'm running Suse Linux on my IDE-HD and I could also had no problems getting my Suse 10.1 installation to install on the SATA-HD. I've booted up with winxp media install disk and tried to use the F6 key at the right time but nothing happens so it keeps going until I get to the point where I can press the S key to install SATA RAID driver from disk that came with my motherboard. The drivers install but then windows install still says no disk to install windows... I don't get it.
I've checked my bios and SATA in there, in fact the first thing I see when I boot up in the boot sequence is the SATA drive. Linux knows it's there but windows install doesn't. I installed XP on a WD SATA drive before and all I had to do was press F6 to install the controller from the XP disk but that doesn't work now.
I'm not completely computer illiterate but i have never set-up a dual or triboot system before.I want to triboot XP Pro, Vista Home Premium and Ubuntu. I have a brand new 500GB SATA hard drive which is straight out of the box. I don't have vista yet but plan on getting it soon (when the next service pack is released) and don't want to have to reformat my hard drive when i do. So i thought it would be better to prepare for it now
View 1 Replies View Relatedinstalling xp on a sata drive as windows xp wont see the drive i know i need the sata drivers but cant find the rights ones for my board its gigabyte g31m-es2l chipset g31 express
View 6 Replies View RelatedI just bought me a new SATA 250GB Hard Drive and a external hard drive enclosure. I received the items today and I just realize the hard drive enclosure doesn't build into the way to connect to the SATA 7-pin data connector. All it has is the Parallel ATA 40-pin data connector. Can anyone recommend any external hard drive enclosure that can connect to SATA connector directly. And there is a main reason why I choose a SATA hard drive.
View 1 Replies View Related