I recently bought a WD 74GB Raptor harddrive to install XP on, but I'm having problems. Every time I load up XP setup from the setup CD, when it gets to the part where the installation options menu is about to appear, as it tries to boot windows from the CD, I get a BSOD and have to restart. I've tried running the CD with my other 80GB WD IDE hard drive inside and it doesn't cause this stop error. I've been screwing with this for 2 weeks now trying everything I can find on google and forums to fix this problem. I have the correct SATA drivers for my board as well for the drive of which I hit F6 for at the beginning of setup.
I'm getting extremely frustrated with a problem I keep encountering trying to install a new SATA Hard Drive. I connect the SATA HD power & data cable I prepare a FDD with the necessary HD Cotroller Drivers from the motherboard utilities CD I boot the PC I insert my XP Pro (SP2) CD The PC boots from the CD I press F6 when prompted for 3rd party drivers When prompted, I install the necessary drivers from the FDD I then get to the bit where I chose to install Windows rather than do a Repair - when I select install, I'm told that no HD is present & that I need to exit by pressing F3 I've tried removing RAM to see if any is dodgy but still encounter the same problem.
I've attached the new SATA HD to a different PC & everything moves on perfectly but I quit before formatting the drive as I want to do a clean install on the other PC. I'm beginning to think that there might be a problem with the Motherboard but am open to suggestions (the old HD is stuck in an infitinte boot loop & am unable to slave it to another HD as it wont respond - maybe caused by a Motherboard problem?).
After my last hard drive took a nosedive, I went out and bought a Western Digital Serial ATA 500 gb harddrive. I've physically put it in my Sony Vaio Desktop. I am trying to install Windows XP Professional now. When I get to the Setup screen is says Unknown Disk. I've already seemed to install the drivers for the new harddisk (they provided me a CD to install the drivers, it came with a program called "Lifeguard Tool" or something like that.
I have tried pressing F6 to install a RAID driver using the Windows setup... I pressed S... but then I find out I need a floppy disk drive... even if I had one, the box only came with a CD and not any floppy disks. I've tried slipstreaming Windows xp cd, service pack 2, and the drivers onto one bootable cd, it did not work... i'm too tired to go in there and find out why. *sigh*
I'm running a sata hard drive and cannot use ide drive .I have a MSI neo2 7025 board i installed a 36gig10,000 sata drive and made it my main drive and wanted to use 250 gig drive as slave but when i hook it up the computer will not fire up . so i went to set up and look for the ide drive and it did not show any ide drives.
I am copying a hard drive from an old computer, I don't have the computer, just the hard drive. I am using an SATA/IDE to USB 2.0 adapter. The problem is, when I try to copy the files, it wont let me because it says I don't have the permission. I change the security settings and it still wont let me open the documents or files.
I'm getting a Bad_Pool_Caller BSOD, along with some misc. BSOD's while trying to do a fresh install of Windows from a SATA Cdrom to an ATA IDE harddrive. Are there any known issues with trying to install an OS from SATA to IDE?
I was supposed to have SATA hdd as well, but shipping screw'd up, and I got sent an ATA instead. I'm pretty sure that I will be able to figure out the solution tomorrow when I get to record the other information on the BSOD screens. I was just curious if there are any known issues or negatives associated with writing from a SATA cdrom drive to an IDE?
Windows 2000 pro Small master harddrive was full installed an old harddrive from another computer an 80gig axs a slave. it shows it is drive letter F and can open it I deleted all the files that were on it so it is empty. Itshows in computer managment but how do I get it so I can put folders, files and like put the antivirus on that drive, I think I did something wrong but don't no what it is. It shows in computer management as Drive F and I put it as NTSF like the master drive
Reformated and reinstalled windows xp. after instalation finished.i noticed i actually have 2 versions of xp home on my harddrive, how do i remove one without it effecting the other? i did this once before thur the reg ( i think) but i cant remember how.
This is the first time i have tried to format a sata drive. I put the disk in and boot from the cd and it goes straight into the xp splash screen it doesn't even give me the chance to hit f6 thats the first problem.
I cannot install Windows XP onto a SATA hard drive. I read that I need to install the drivers for the HD separately during the Windows installation but how do I do that.
I can't install Windows to the SATA drive. It loads everything it needs, then when it tries to boot, it says the files aren't found. I'm guessing it can't read it without the drivers installed, but how do i do that with no OS? I was thinking of dual booting with linux.
first and foremost is considering I have all of the old videos, files, pictures etc on my 80 GB Maxtor that I plan on transfering to the SATA hard drive since it's faster and I'd like to use the SATA as my primary...so all in all that makes things complicated in itself.
What I did was got everything ready, I didn't back up anything from the Maxtor (IDE) because that is out of the plan since I hope to do a simple drag and drop transfer of all the old stuff to my new SATA hard drive. I went into my BIOS and set the boot priorty to the SATA and it detected my SATA drive fine. I got out of the BIOS and inserted my Win XP upgrade disc. I let it go and also inserted the SiS 964 RAID Installation support disk so that it would install the SATA controller that was included in the Foxconn mobo. Then keeping my IDE drive intact, I deleted and formated the SATA to create a partition and installed XP on it......
My computer uses SATA HD. Right now it functions properly and boots into Windows just fine. But I need to reinstall the XP Pro. So I boot from the CD but the setup does not see any HD. Are there any special instructions on installing on a SATA HD?
I'm having problems with windows xp on a laptop with preinstalled vista that has no floppy drive, the error "It doesn't detect the SATA HDD"; I tried the solution with a usb floppy drive and pressing f6, I found the correct driver and it works fine, I`m able to partition the HD and the process continues until it asks for the driver again but the USB floppy drive doesn't wortk in that part of the installation.
The next solution I found of this forum was making a custom XP CD including the SATA drivers with NLITE software, incredible software, without pressing f6 the HD is detected and again I'm able to partition and the installation begins, almost success!! but ... when it reboots to continue the installation it does't detect the HD again a lecture error displays and the classic press ctrl+alt+del to reboot!!! Am I missing something?
i am new to this forum, but i have looked everywhere and i have a problem i can't seem to find the answear to. I reformated my harddrive, it is a seagate baracuda 160gb drive. I have it hooked up by raid i think. Anyways when i boot my computer it sees that i have a harddrive, but when i go to load windows it doesnt find it. I heard i need to install drivers for it, but i dont know which ones and where to get them from.
Just bought a 300Gig Maxtor SATA hard drive. My supports the connection onboard. How do I get Windows XP pro to reconized the full 300Gigs and not just 137Gigs. I have a Intel(R) Desktop board D85GVHZ Base System Intel(R) Celeron CPU 3.06Hz 512MB of ram.
I have recently bought a new computer that came with windows vista as you may have guessed the experience mostly has not been a good one, with lots of compatibility issues. I want to dual boot Vista with XP but the problem is I have heard windows XP does not have the SATA drivers on the disc. I understand that you just need to insert a floppy and push F6 I think but the problem is I don't have a floppy drive! Is there anyway I can slipstream the drivers into the install or something?
I am having a heck of a time with this. I am trying to install Windows XP on a Lenovo R60e that has a SATA hard drive. I cannot for the life of me find the driver. I cannot seem to find anything resembling this driver on Lenovo's "Driver Matrix" or anywhere else on their site. Is there a generic one out there that anyone knows of? I want to slipstream this into an XP install, but I can't do it without the driver.
Long story short - Athlon/mobo on old unit died, 3 hd's (all WD eide 80 [C:], 40 [F:], 80 [G:]) & 1.5 gb memory good until mobo failure. Had shop install new mobo along with intel duo processor, new ATI video card, reinstalled memory & both 80 hd. Installed WD SATA 160 [replacing WD 40 hd] & tried to make it master boot record. Had shop transfer files from old WD 80 [C:] MBR to SATA 160, leaving files on 80. Did an repair install of xp on old 80 hd. Wouldn't boot. Tried reinstall of xp on SATA 160 & rebooted. Able to do so, but couldn't access internet for updates. Got sp2 update disc from technician & updated, then restarted.
My friend is trying to install Windows XP on his computer, but he keeps getting the message"Setup did not find any hard disk drives installed in your computer. Make sure any hard disk drives are powered on and properly connected to your computer, and that any disk-related hardware configuration is correct. This may involve running a manufacturer-supplied diagnostic or setup program. Setup cannot continue. To quit Setup, press F3."He has 2 IDE hard drives, one set as a Master and the other as a Slave, and both are connected properly. His BIOS picks up the hard drives, but XP can't.
internal hard drive delete all partition and create a ntfs partition. (due to some problem)I put the windows xp disc to boot ; Ntldr is missing. (boot prority set to cd)I extract Ntldr and ndtect from the windows xp disc and create boot.ini, then put all three file to the internal hard drive.This time it said hal file is missing.
I was wondering if it makes any sense to buy and install a SATA 300 controller to work with two WD SATA 300 drives. I kind of doubt I will achieve 300mb buffer to host transfers with only SATA 150 motherboard.
I have integrated the drivers onto the windows xp home disk using nlite as well as integrating sp2 but after the restart it keeps saying failed to load os, why should I do to install it on my sata drive? this is making me consider consider vista, does vista install to sata drives straight from the disk?
This is similar to the problem B1177 posted about, but I'm having no luck solving it myself. Basically, I have an IDE CDROM into the mobo, and a SATA HDD hooked to a Koutech Initio-chipset SATA controller card. In the card's setup at boot, it says the drive is "passthrough". I confess I'm not sure what that means. I'm new to SATA. I slipstreamed the Inic1620 drivers into a new CD with nLite, which stopped the "Setup cannot find any hard drives..." error, and allowed Setup to continue. After loading files, however, on restart I get the ever popular STOP 7B BSOD. Windows DOES begin to start, and the splash screen shows for a second or so, then it's into the ol' freezerino. Email to Koutech support has gone unanswered.
The machine is a Gigabyte 6IEML/P3900/500MB with an Intel 82815/801B chipset. I also tried restoring an image from another machine with an Intel chipset--though not the same one--and it stops at mup.sys, but that may have nothing to do with the SATA card. Interestingly, although Windows Setup couldn't find the drive, a Hiren's CD, with no SATA drivers loaded, could. Actually, a bit more than interesting isn't it?
Doing a fresh install of xp on a sata drive. When it asks to press F6 to install the third party drivers will I be able to load off the motherboard driver cd, or does it *have* to be a floppy.? Reason is the folder that contains the driver info on the cd is over 6mb so obviously won't fit on a floppy..and I'm not sure which I need to complete the install. If I habe the driver cd in the second cd drive will I be able to browse to it when asked? Failing that, just what info do I need to put on a floppy?
I want to replace Vista with XP however my laptop has a SATA HD. I know that I can create a boot disk on either a floppy or a CD however I think it should be possible for me to install the drivers on an external USB HD? Before I format my drive I just wanted to confirm that this is possible?
I want to install Windows XP on a new SATA HDD drive. The computer in question came with Windows Vista installed. There is no IDE option in the BIOS. There is no floppy drive on the unit. So it looks like I might have to slipstream all the drivers, etc., on to the unit (which I have no clue how to do). I do not have the motherboard make or model number, nor do I have the motherboard CD. My business partner is trying to take the cover off the laptop as we speak, but we're having trouble getting it off. Thus, as of now, we can't identify the motherboard manufacturer or the serial number.
Can anyone here point us in the right direction? The computer in question is a Compaq Presario c769us (laptop). It was purchased in June 2008. This all started when my business partner decided to use a Vista System Recovery CD to overwrite the existing copy of Vista that he had on the computer. After he ran the disk, the system stopped working. So right now, we have the old hard drive, which contains a non-working copy of Vista on it (which we can 't delete), and we have the new hard drive (a 250 GB Hitachi). So maybe we could just delete the copy of Vista on the old hard drive - the self drive test checked out okay on the old hard drive. So I guess the two options are - figure out a way to put XP on the NEW hard drive, or figure out a way to put XP on the OLD hard drive and delete Vista from it first. If we can put XP on the old hard drive and remove Vista from it, we could take the new hard drive back, and get our money back, too.
My old IDE hard drive went out on me so i went and bought a 500g WD SATA hard drive. When I put the windows installation disk in it does not recognize my SATA hard drive. after looking into it online, i found that alot of people had this issue. I read a few suggestions and tried them, (using the F6 function during install with drivers on a floppy disk, and streamlining drivers intot he windows installation disk itself using NLite), and none of them seem to work. I then used my friends old IDE hard drive, installed windows, and used a program to make a disk image of my hard drive and transfer it to my SATA drive. This didnt work either. I havn't fiddled with drive letters, (you know c: and e: and so on) i am thinking this may help but I am not sure. It is not a boot order issue i know how to do all that and nothing works. I am looking for a way to get Windows XP onto my SATA drive. (yes my mother board detects my SATA drive, and it is showing up in windows i just cant seem to get windows on it.)
I would prefer to just copy it from my IDE drive since i have already installed all the updates so if this is possible please let me know.If you know what kind of boot disk i need for windows xp installation to recognize my sata drive during installation that would be a big help too. (i have tried sata controller drivers for my motherboard, i tried using the software that came with my hard drive, and this too didn't work.)
Mobo is Biostar p4m90-m7c fe Bios finds 320G SATA drive fine.
Put Win XP HOme (original version from wayyyyyyy back) in cd=drive. XP boots from disk and sees the drvie but ONLy as 130 or so Gigs. I realize this is a limititation of xp prior to all the service packs, but how do I get around it? BTW there is no Floppy in the computer (none of my puters have working floppys!) I thought I'd be tricky and installed the disk to my other winxp machine and formatted the drive into a 40G and 280G partitions both primary the 40G first. Retried the new machine and it didn't recognize the partitions and listed only one unknown drive of about 130 gigs.
Looked int he bois and didn't see a setting for ide/raid for the sata. I've read where you can F6 durring the install and load additional drivers but all those post linked to external sources for key information and those links were dead. How can I get around this limitation? If I need to load drivers during the install I assume I can burn them to a cd on my other computer and f6 during the install to load them, but what drivers am I looking for if this is the way to go? If not how can I get all of my drive available. I did try simply letting install format the 130 partition hoping that when I finished the install the rest of the drive would show up as unpartioned but that didn't work out.
