I have problems if I try and run the display settings above 800x600. I was wondering if this would be fixed if I upgrade the firmware settings and if so where would I get these upgrades? Whenever I try and run it at a higher display setting all I get is a thing saying "Signal isnt compatible with this display setting".
View 6 Replies
With a lot of help I've been able to fix the Control Panel>Display problem I had earlier.But now I have another problem. I started a new thread because it is a different problem, and because it may be a Viewsonic monitor or ATI screen driver problem rather than a Windows-XP problem.When I have the screen resolution set to 1024*768 the desktop fits neatly into the monitor.When I tried it at 1280*720 the desktop fits neatly into the monitor, but the graphics and text look as though they are stretched vertically - ie too tall for their width.When I tried it at 1280*768 the proportions looked right, but the desktop seems to have been moved up and to the left. That is, there is about a 2cm black band to the right of the display, between the right edge of the monitor and the right edge of the display; and there is about a 1cm black band below the desktop.When I tried it at 1280*800, just for completeness, the whole desktop seems to overlap the limits of the monitor. That is, the icons on the left are half hidden 'behind' the monitor, and the task bar at the bottom is barely in sight at the bottom edge of the monitor.I don't remember having this problem in the past, but it's been quite a while.
View 11 Replies View RelatedI have this pentium 3 - 700 mhz computer which today I formatted and installed windows xp pro on it. The motherboard on the computer comes with a SIS 5598/6326 display adapter for which I been searching the internet for its WIN XP driver but havent found any except for the other versions of windows are available.What can I do if there is no WIN XP version of this driver?
View 1 Replies View RelatedI was restarting my computer and right after I restarted my computer the resolution was as low as it could be and my display(graphics) setting was very, very low. so low that it is using like 4 bit color and stuff. And I went into display properties and changd my res and my color bit back to the highest,but it wouldnt change, but yet again it said the highest was like 32 bit and im pretty sure there was 256 or something higher.
View 11 Replies View Related1: Because of my eyesite I always have my screen resolution set at 640 by 480. On the computer with XP it is not avalible. Is there different drivers or a program that will let me make 640 by 480 avalable? If so how do I go about this?
2: I have 2 computers that are virtually the same. Both have XP Pro opperating system. I am the webmaster for a couple of sites. there is a menu at the left of the site. On one computer the menu will display on the other is will not. The menue is an applet code . Is there a setting on the second computer that I am missing to display this menue?
3: for years I used Norton. When I loaded XP I used it a day or so and then loaded Norton on that PC. It slowed it down very much. So much that I took it back off. Now I need a suggestion on what virus scan will be as good as Norton but not slow my PC down so much.
Anyone having problems with resolution settings nvidia display.
View 10 Replies View RelatedInstalled win xp but unalble to change screen resolution from 640X480 pixels. Res. Color quality (medium 16bit). Slider will not move. Can’t change dpi setting.Posted using the http://www.windowsforumz.com interface,at author's request Articles individually checked for conformance to usenet standards Topic URL: http://www.windowsforumz.com/Video [...] 50570.html Visit Topic URL to contact author reg. req'd.
View 1 Replies View RelatedA problem regarding desktop display settings. When the desktop resolution is set to 1024x768, everything is perfect. However, when I change the resolution to 800x600, everything is very bad quality such as text and images.This corruption also affects fullscreen applications that run in a lower resolution than 1024x768.
View 7 Replies View Relatedtrying to change the resolution to fit more on the screen but resolution bar will not slide in display settings
View 6 Replies View Relatedbrowsing web sites, and right before my eyes (not even a screen flicker) the display widens, while the resolution remains the same; looks like my monitor needs to be a few inches wider on each side to fit it all. "That's weird," I thought, and went and tried to fix the display as per usual...no dice. Reboot, no dice. While rebooting, I noted that the startup BIOS info was wide too, and not fitting on the screen...I booted up Ubuntu Linux just to see, and it works just fine...so
View 5 Replies View Relatedcompaq presario 5000, 5BW130, new seagate hardrive, new install of windows xp sp2.My problem is I want to change the screen resolution, in display properties it won't let me move the slider it's set for 800 by 600 pixels, can't move it any further, color quality is: High 24 (bit) or medium (16 bit)that's it I want to make thing smaller what do I have to do, and what do I need??
View 2 Replies View RelatedI am unable to display a screen resolution of less than 1600 by 1200 Pixels correctly. Instead of filling the whole displayr I end up with a Window in the centre of the display that gets smaller as I change the screen resolution to less. I am using an IBM Thinkpat A22p and this problem occured just after I attached an external LCD Monitor.
View 1 Replies View RelatedWindows display setting keeps resetting after startup On startup of my computer the monitor screen displays normal sized icons, then enlarges to gigantic icons. After all programs are started I right click on the screen and click on properties. Display properties open, then I click on settings and move the slider to my likings, I click apply and the desktop reverts to normal size and operates in all areas normally. The problem is I have to perform this task every time I restart my computer. It's obvious that the apply/ok
setting in the display properties setting is not sticking. Is there a fix for this condition? Please HELP. Running Windows XP.
Submitted by: Mel W. Here are some featured member answers to get you started, but please read all the advice and suggestions that our members have contributed to this question. ....
I have a Dell D610 laptop running WinXP Pro. The screen is an SXGA+ (1400x1050 resolution). I have a docking station at home and use a 19" wide screen LCD monitor (1440x900). My docking station at work has a 23" wide screen LCD monitor (1920x1200). The laptop and home 19" monitor look good at normal size (96 DPI) setting. However, the large 23" monitor needs the Display DPI Setting increased to large size (120 DPI) for my old eyes.
The problem is having to constantly change between normal and large display DPI settings. This change requires a reboot to take effect. Is there a program or script available that will run at startup and allow me to choose the DPI setting? Even better would be a startup script that detects which monitor is in use and sets the display DPI accordingly.
I fixed this problem a few months ago, now it back and I forgot what i did.(rolling eyes) The display setting seems to be fixed at 640x480 lowest 4 bits color quality When I try to change it to 1280x1024 highest 32 bits and hit "apply" is reverses itself back to 640x480. 4 bits or 1280x1024 stays there but the bits goes to lowest 4 What to do? The monitor dpi set at 96 with nividia forcefx5500 "device is working properly"
View 9 Replies View RelatedI just replaced a power supply on a Windows XP computer and when it boots up, the os loads just fine, the startup programs begin to load and during this the display settings automatically change from 800x600 32-bit color to 640x480 8-bit color. It has a GeForce 440 MX card and all the drivers and such are working fine. I've tried everything fix it, but am having a less than fun time. Any suggestions would be great.
View 1 Replies View RelatedI was trying to improve my monitor display and did something that is causing text fields to be blacked out. I can see icons and what I think are highlighted text but most of it is all black so I can't see the settings to try to fix??? The monitor works fine and the XP start up graphics are normal. It's just once the desktop is loaded.
View 5 Replies View Relatedwhile I was in the diplay settings of the control panel, I accidentally changed the DPI from normal to the highest in windows XP -now the fonts are so small that I can't change it again-any.
View 1 Replies View RelatedI recently uninstalled what I thought were some unnecessary fonts on my XP SP2 notebook, but began having serious display problems in some apps and dialog boxes, the text being either much too small or large.I've trimmed the Fonts folder in the past with no problems, but this time I seem to have majorly screwed the pooch. Even after reinstalling all fonts, the problems persist.
View 2 Replies View RelatedI'd like to permanently set my open and save file dialogue boxes to display thumbnails instead of the usual list display but can't find any way to do this (the folder options setting doesn't appear to affect this aspect of windows XP).
Can't change default Monotor for higher Resolution in XP?I have tryed Control Panel-Display-Settings-Advanced-Monitor Tab and I find the monitor properties are grayed out and monitor settings have no alternative choices.
View 10 Replies View RelatedI have a problem when i start up my computer, if i have my screen resolution at 800x600 and i start my computer it will make the resolution the maximum (1600x1200) and it will make a black boarder that is like a quarter of the screen all around. Can this be because of a virus that messed something up?
View 2 Replies View RelatedI've changed the screen resolution from 800+ to 10000+ range and back to 800 several times. This so that a program I am using will fit the screen (10000) and back so icons and print on desktop are bigger. Now I can no longer get dsplay to open and can't do anything with the display. I'm using Windows XP
View 2 Replies View RelatedWhile playing a game I hit some buttons on accident and the display shrunk. Now the monsters are small, and so is everything else outside of the game I have no idea what I did, I checked the Screen Resolution and it seems fine, and I also checked my monitor settings, which is fine.
The monitor started showing graphic distortion. I ordered a new monitor but had the same distortion on it. I updated the ATI drivers but it did not solve the problem. In trying to trouble shoot the problem following directions on the ATI website, I changed all the graphic settings to the lowest and slowest available. This got rid of the distortion but the settings need to go! Now I cannot open the display settings.
View 3 Replies View RelatedMy XP is currently defaulted on it's display settings 640v by 480 pixels and will not allow me to change it. In fact, there is nothing to change it to. I dont know what file I must of deleted, but is there anyway I can download the driver or something to make it so that it can be set on opitions that are higher?
View 7 Replies View RelatedAll my text/font display settings seem to have changed. I downloaded a freeware program today called avi2dvd, to convert avi video files to iso files for burning to DVD. I tried it out, got frustrated with it, and uninstalled it. After I uninstalled it, I went to check my email. That's when I first noticed that all the text in my yahoo email account had changed - it seemed smaller, like it was at a lower resolution.
I clicked on a few more pages and it was the same for all of them - the text was just not as...smooth. Not as readable. And definitely smaller. It's not just a font size thing, I'm not that much of a newbie, I tried enlarging the font and it's definitely a resolution thing, not just a font or size issue. Then I tried out some other programs, and found out that the problem was system-wide. I use a writing program called Final Draft, and the text in that is also less readable.I found one program that hadn't been affected: IE all my web pages display fine in Explorer.
my mom installed a virus the other day on accident. (Some program called Dr. Spy Shreddar, or something like that.) I deleted it, but some stuff was weird with the computer. I tried restarting the system to get the old configuration back, but the virus just installed itself again. I removed it again, using instructions from Systematic Antivirus and now it's really gone. Some of the settings were still weird though. So after hours of searching the help topics on Microsoft I managed to fix 1 & 1/2 of the problems I had/have.
For one of the problems they made me go into the registry and set something to the value of 0 in order to get the desktop tab back in the Display Properties box. (You know when you right click on the desktop and select properties.) That's all fine and dandy, but here's the other 1/2 of my problem: I can't access some of the features in the tab. (I have Windows XP Professional, by the way.) I can't click inside of the background list and it's shaded a sort of brownish beige color. I also can't browse and do anything with the position setting. I can however access the customize desktop and color features
I was installing security cables for the computer stations. when I finished and rebooted the computers(had to disconnect power and other cords to run the security cables) one of them had a display problem.
it seems that the display area has been reduced. the functional area of the screen is maybe 60% of what it should be. in this area it is complete with the full desktop able to be accessed and nothing is missing. but the right 20% of the screen is solid black (cursor stops at the boundary) and the bottom 20% of the screen(that's not black) is displaying a second image of the top 20% of my desktop. (cursor also stops at this boundary.)
I reinstalled XP Pro with SP1 on my computer today. Everything is working well except when my desktop loads the actual display is about an inch to the right on the screen. If I go into properties and change/apply the screen resolution from 800 x 600 then back to 1024 x 768 it realigns and all is well. I would just prefer to not have to do that each time I restart windows.
View 4 Replies View Relatedmy mom installed a virus the other day on accident. (Some program called Dr. Spy Shreddar, or something like that.) I deleted it, but some stuff was weird with the computer. I tried restarting the system to get the old configuration back, but the virus just installed itself again.For one of the problems they made me go into the registry and set something to the value of 0 in order to get the desktop tab back in the Display Properties box. (You know when you right click on the desktop and select properties.) That's all fine and dandy, but here's the other 1/2 of my problem: I can't access some of the features in the tab.
View 8 Replies View Related
