compaq presario 5000, 5BW130, new seagate hardrive, new install of windows xp sp2.My problem is I want to change the screen resolution, in display properties it won't let me move the slider it's set for 800 by 600 pixels, can't move it any further, color quality is: High 24 (bit) or medium (16 bit)that's it I want to make thing smaller what do I have to do, and what do I need??
View 2 RepliesInstalled win xp but unalble to change screen resolution from 640X480 pixels. Res. Color quality (medium 16bit). Slider will not move. Can’t change dpi setting.Posted using the http://www.windowsforumz.com interface,at author's request Articles individually checked for conformance to usenet standards Topic URL: http://www.windowsforumz.com/Video [...] 50570.html Visit Topic URL to contact author reg. req'd.
View 1 Replies View Relatedtrying to change the resolution to fit more on the screen but resolution bar will not slide in display settings
View 6 Replies View RelatedMy XP is currently defaulted on it's display settings 640v by 480 pixels and will not allow me to change it. In fact, there is nothing to change it to. I dont know what file I must of deleted, but is there anyway I can download the driver or something to make it so that it can be set on opitions that are higher?
View 7 Replies View RelatedI reinstalled XP Pro with SP1 on my computer today. Everything is working well except when my desktop loads the actual display is about an inch to the right on the screen. If I go into properties and change/apply the screen resolution from 800 x 600 then back to 1024 x 768 it realigns and all is well. I would just prefer to not have to do that each time I restart windows.
View 4 Replies View RelatedOn my Dell 8250, I added a 1800 Flat Panel display and when I went to load the drivers, I found the Properties button greyed out. I went to device manager and no monitor was listed not even the Default Monitor. I've looked all over and can't find a clue on how to ungrey the Properties button.
View 1 Replies View RelatedOn my Dell 8250, I added a 1800 Flat Panel display and when I went to load the drivers, I found the Properties button greyed out. I went to device manager and no monitor was listed not even the Default Monitor. I've looked all over and can't find a clue on how to ungrey the Properties button.
View 1 Replies View RelatedI use a Dell LCD Monitor and every time I have tried to format and reinstall XP on my hard drive I go to my Monitor section and the Monitor Properties are shaded out thus making me stuck with the default crap that XP put on for my comp. I have the drivers I need for my monitor but the frackin thing wont let me use them.
View 6 Replies View Related1: Because of my eyesite I always have my screen resolution set at 640 by 480. On the computer with XP it is not avalible. Is there different drivers or a program that will let me make 640 by 480 avalable? If so how do I go about this?
2: I have 2 computers that are virtually the same. Both have XP Pro opperating system. I am the webmaster for a couple of sites. there is a menu at the left of the site. On one computer the menu will display on the other is will not. The menue is an applet code . Is there a setting on the second computer that I am missing to display this menue?
3: for years I used Norton. When I loaded XP I used it a day or so and then loaded Norton on that PC. It slowed it down very much. So much that I took it back off. Now I need a suggestion on what virus scan will be as good as Norton but not slow my PC down so much.
With a lot of help I've been able to fix the Control Panel>Display problem I had earlier.But now I have another problem. I started a new thread because it is a different problem, and because it may be a Viewsonic monitor or ATI screen driver problem rather than a Windows-XP problem.When I have the screen resolution set to 1024*768 the desktop fits neatly into the monitor.When I tried it at 1280*720 the desktop fits neatly into the monitor, but the graphics and text look as though they are stretched vertically - ie too tall for their width.When I tried it at 1280*768 the proportions looked right, but the desktop seems to have been moved up and to the left. That is, there is about a 2cm black band to the right of the display, between the right edge of the monitor and the right edge of the display; and there is about a 1cm black band below the desktop.When I tried it at 1280*800, just for completeness, the whole desktop seems to overlap the limits of the monitor. That is, the icons on the left are half hidden 'behind' the monitor, and the task bar at the bottom is barely in sight at the bottom edge of the monitor.I don't remember having this problem in the past, but it's been quite a while.
View 11 Replies View RelatedI am unable to display a screen resolution of less than 1600 by 1200 Pixels correctly. Instead of filling the whole displayr I end up with a Window in the centre of the display that gets smaller as I change the screen resolution to less. I am using an IBM Thinkpat A22p and this problem occured just after I attached an external LCD Monitor.
View 1 Replies View Relatedi just installed a new copy of windows xp pro. the screen resolution before the fresh istall was fine. i had all the options. i like my windows small. and now the only resolution i can get on is 1280x1024.. how can i fix this? do i need drivers?
View 9 Replies View RelatedThe video card on this computer would just cut out from time to time, and i'd to have re-set the cable for it to work. i figured theres a loose connection, so i got another video card to replace it with, since this is a work computer.So after installing the new (actually its a used video card, ASUS v7700 TIvx, but still definitely works) video card, the computer starts up at the correct resolution, 800x600. It looks fine, but when you drag anything or scroll on a web page, the video lags. So i found the correct drivers and installed them, and rebooted.
The computer reboots in 640x480 at 4-bit color quality. when i change the resolution to 800x600 at 32-bit color quality, it just defaults back to 640x480 at 4-bit. i found that i can change the resolution to 800x600 at 4-bit, but when i try 16-bit or 32-bit quality, it just go right back to 640x480 at 4-bit.i thought maybe it was the video card, and tried to install the old one again (its a geforce 2 mx card). so i re-install it and install the correct drivers, and still the same exact thing happens, (prior to any of this, the geforce 2 mx card worked fine at 800x600 at 32-bit) i can't get it to correctly change to 800x600 at 32bit, it just keeps defaulting back to 640x480 at 4-bit.
How can I change the resolution of Windows XP bootup screen? i.e.The screen of Windows XP logo with a blue moving bar(Change from 640x480 to a higher resolution)
View 2 Replies View RelatedI have a Dell Dimension 2400, with Windows XP Home Edition. I installed Symantics PC Anywhere 9.2 and it reset my screen resolution to 640x480, I've tried to change it to original setting of 1024x768 but it won't let me change it.
View 4 Replies View RelatedCan a shortcut be created to access the change of screen resolution instead of desktop, properties, and settings? Or is there any other way to do it?
View 7 Replies View RelatedSince installation of Home Ed with Service Pack 2 there have been no problems with this computer I decided to change the monitor resolution to make reading a little easier and did thid Control Panel/Display. Rebooted for changes to take effect and the normal Windows screen appeared (showing the progress bar) and then when I expected the 'Welcome' screen to appear all that I get is a small window showing the words
View 4 Replies View RelatedThis is confusing the heck out of me. on my screen is a black line approximately a pixel thick that runs horizontally over everything. When I change my screen resolution (changing it from 1280x1024 to 1152x864 and back again) it disappears.
It shows back up roughly about once week in differnt places (closer to bottom, closer to top, smack dab in the middle, etc.) This has been happening for months. Doesn't affect my work all that much. I am just a little curious as to what causes it.
I just reformatted my computer a Dell, Inspiron 8100, Windows XP home edition. Screen resolution default is 1600X1200 Pixels. I like 1024X768. When I change the resolution to 1024X768 or any other setting available the screen just gets smaller. There is no change in "Screen Resolution.
I have installed all the updates and SP2. Auto-updates seems to be doing fine. I downloaded new NiNida drivers from Dell, etc. I've removed and reinstalled the video drivers several times.
I cannot change the size of me screen resolution past 600x 480...or something like that. I have reinstalled windows and everything and i just cant get it to change.
View 3 Replies View RelatedI recently re-installed Windows XP on my Acer Aspire 5920 laptop. My only problem with it is that I can't set my screen resolution to the actual resolution of my screen (1280x800) since the only two options are 800x600 or 1024x768.The nVidia driver I got on the acer website wont install, saying:The NVIDIA Setup program could not locate any drivers that are compatible with your current hardware. Setup will now exit.
View 5 Replies View RelatedI've changed the screen resolution from 800+ to 10000+ range and back to 800 several times. This so that a program I am using will fit the screen (10000) and back so icons and print on desktop are bigger. Now I can no longer get dsplay to open and can't do anything with the display. I'm using Windows XP
View 2 Replies View RelatedI have just installed WXP PRO on a new (bigger) HDD in my Compaq D51SP225 computer but the screen resulution cannot be increased in control panel -- display.
I think I need a video driver but cannot install the internet connection because of thw resolution problem. All is well with this HDD. Can I download a suitable driver from the web to a CD or transfer this driver to a CD?
Recently reinstalled Windows XP SP2 Home, due to a messed up Registry and upon reinstalling my screen resolution became 640 x 480 px, and whenever I try to change it, my computer won't let me. According to Microsoft.com, I have to install the driver for my monitor. I can easilly re-download the driver from the Dell website, but for some reason my computer won't let me go to Monitor settings. In order to install the monitor's driver I need to access this. Below is an image of the Advanced Display settings window when I open it. Note how the Monitor Properties is unclickable.
View 14 Replies View RelatedI had to replace my HD and Video card a couple of months ago. I got the new video card from Dell, it is the same card that my system came with, GeForce 7800 GO. Since replacing these two items, I cannot achieve my original screen resolution of 1920 X 1200(WUXGA), all I can get is 1400 X 900(WXGA). Yes, I am sure it is WUXGA, as shown by dell configurator : CF176 LIQUID CRYSTAL DISPLAY..., 17, Wide Ultra Extended Graphics Array..., VIDEO ELEC. STDS. ASSOC...., GLARE WIDE VIEWING ANGLE..., SAMSUNG...
View 2 Replies View RelatedI have a Compaq EVO D51S SFF which I had plugged to my LCD TV as a media centre, just to watch movies and all. I had not connected this computer to the internet because I did not have a wireless card.I finally installed a wireless card, and then windows started doing all sorts of updates as expected (since the version on the SFF was SP2).Once windows was done with the updates, I started having problems with the screen resolution.
The SFF does not have a stand alone video card, so I had set the resolution at 1024 x 768, and this worked just fine before the updates.Now, the resolution keeps changing and this is a problem because the LCD TV gives me a message saying "Resolution Not Supported", so I can't use the computer unless I connect it to a regular computer monitor, select 1024x768, and then connect to the TV. I connect via VGA port, not DVI (don't have DVI).
When I right-click, and get the Display Properties, I only have three tabs: Themes, Appearances and Settings. I no longer have Screen Saver and DeskTop tabs
I'm not sure when they disappeared, but most likely when I had a virus. I've gotten rid of the virus, but the Screen Saver is gone.
I'm running Windows XP, of course. How can I get my tabs back?
I have problems if I try and run the display settings above 800x600. I was wondering if this would be fixed if I upgrade the firmware settings and if so where would I get these upgrades? Whenever I try and run it at a higher display setting all I get is a thing saying "Signal isnt compatible with this display setting".
View 6 Replies View Relatedmy mom installed a virus the other day on accident. (Some program called Dr. Spy Shreddar, or something like that.) I deleted it, but some stuff was weird with the computer. I tried restarting the system to get the old configuration back, but the virus just installed itself again.For one of the problems they made me go into the registry and set something to the value of 0 in order to get the desktop tab back in the Display Properties box. (You know when you right click on the desktop and select properties.) That's all fine and dandy, but here's the other 1/2 of my problem: I can't access some of the features in the tab.
View 8 Replies View RelatedI'm trying to change my screen-saver, but I can't get into Display. I get a message
View 1 Replies View RelatedMy friend installed a video game on his HP desktop (w/Windows XP) and changed the resolution settings to some odd selection that was 756x??? - something I had never seen before. Every time he loaded the game, it was illegible. In trying to change the display settings to make them compatible with the game, he chose this odd resolution (which was now available for some reason) for the desktop display settings, and now nothing can be read on the screen.
View 4 Replies View Related