computer failed to reboot. I used a boot disk to get started. I then noticed that the system does not recognize the drives C (where my Windows XP OS is installed) or D drive which is a seperate physical drive for my data.
I installed windows service pack 1 for windows xp and now my cd and dvd drives aren't recognized and I lost sound in my speakers. I got a code 39 error. The fix in windows support is useless
View 8 Replies View RelatedI've got this old mobo Abit VT7. I want to install XP on it. However, the XP disc doesn't recognize SATA hard drives. So I downloaded official SATA driver from the Abit website http://tinyurl.com/kua5qz and tries to slipstream my XP disc following the instructions set forth here http://tinyurl.com/37anvn . I am not too clear how to incorporate the drivers from the official drivers, but Nlite seems to be able to find the drivers once I pointed it to the top unzipped driver directory, and I selected the XP folder for it. However, the newly created XP disc still fails to recognize the SATA hard drives. Alternatively, I believe I could have a boot floppy which would load the drivers in, then I launch the setup in the XP installation CD via command line. But I don't know how to create a boot disc which has those SATA drivers in.
View 6 Replies View RelatedThe Dell 8250 Pentium IV computer will not recognize the new master 160 GHZ or the origional, now slave, 40 GHZ, Hard drives. All the connections and jumpers are installed correctly. I tried a new motherboard and a new cable, both did not resolve this problem. Even ran a diagnostic program called "Tuff Test", running at boot up and the RAM and all other items checked OK, showing all working properly. The BIOS, now set to boot up correctly, off the proper drive, seems to recognize both removable drives and the floppy, but not the hard drives.
When I received the computer it was password protected. after asking and waiting for a week, with no response, I therefore, in safe mode,entered the BIOS and chose for it to boot off of the CD Rw that I thought was the proper and shut the Hard Drive off. Here the CD RW was a slave and not the master. No luck in installing the OS. I bought a new 160 GHZ HD with the thought that I could load the OS, again no luck. I replaced the battery and tried again with no luck.
first i get the HP blue screen. I tried F1, but i dont see my hard drive in the boot menu. I followed some steps in Hp's web site- took the cpu apart and unplugged both hard drives from the motherboard, plugged them back in. when i restarted ,i got the HP screen and then windows started to load up. After a few seconds the HP screen came back up and then the black screen: sk boot failure, insert system disk and press enter. I also noticed that pressing F10 for system recovery does nothing.
View 3 Replies View Relatedi am getting a Boot Failure message on my computer when I start it up. It seems like it is trying to boot from the various devices, Then I receive the Boot Failure message.
View 4 Replies View RelatedI have a dwsktop vaio When I boot from cold it does not find hard drive. I get an error message Disk boot failure Insert system disk and press enter. If I restart the computer and go into the bios it does not show the hard drive but when I come out of the bios it then boots up.It will only bootup if I go into the bios first?
View 1 Replies View RelatedI have a 2 hard disc system, Windows XP pro and most programmes run from the C Drive. A few, plus all my data run from the F drive. Over the last few days I have encountered a massive slowdown in getting the computer started - form certainly less than 5 minutes to over 20 minutes. I have not added anything to the autoruns at all.
Programmes and data (eg music) run fine if they are on the F drive, but if they are on the C drive they run incredibly slowly so music is fragmented and at times its like trying to wade through treacle to get anything done. I have been getting crashes of the PC with a message about a kernel problem... but haven't yet copied all the data from that to get the detail. When it crashes the next boot reports a disc boot system failure, when i reboot ahgain it loads up but painfully slowly. The C drive was defraggged just afew weeks ago. I'm thinking the drive is about to pack up....
The system will not boot up. Is there a boot disk I can download? System message: PXE-MDF: Boot Failure: System Halted.
View 4 Replies View RelatedI have a problem with one of the XP Versions on a hard drive. The problem started when my C: drive crashed. I replaced the drive and restored from the back-up I have. Since the new drive is larger than I care to use as a boot drive, the drive is partitioned.The restored back-up has is in the primary partition of the master drive. During the restore the OS stopped recognizing the optical drives(to complete the restore I used the second OS created in the second partition to copy the XP CD onto a partition of the hard drive I use for back-up. This drive is in a drive cradle). I have a CD reader/burner; a DVD reader in the tower; and a DVD burner in a USB2 drive cradle, none of these are recognized in the restored OS. In the process of trying to resolve this problem I installed a second version of XP in the second partition, this version recognizes all of the drives.
View 8 Replies View RelatedI have a computer running Windows XP PRO SP2 with 2, 250gb hard drives. The operating system and programs are on the C drive and the second drive which is removable is supposed to be for my data, but Windows doesn't recognize it so I can't use it. Right now I have my data on an external hard drive, connected by USB.
The second hard drive is new from my manufacturer (I have a custom computer and this is a replacement hard drive--the original was faulty) and I haven't put anything on it yet. When I first put it in my machine, I was able to see it in "My Computer". The next day when I was ready to start copying my data over, it was nowhere to be found. I turned off the machine, pulled out the drive and put it back and rebooted--still no show.
I reinstalled and reformatted my hard drive, and the other one inside.I have a drive calledC: (Boot) SATAII - XP on on itD: (System) IDE - Just Data on itI reformatted C and D.The C: seems to require D: to load XP though- Is there some boot.ini to fix this?- I tried changing the BIOS order but that wont do any good.It appears they now work together and windows won't boot without the other drive.
View 2 Replies View RelatedAfter running a defragmentation, I received a message that 6 mb of system 32 did not defrag. the system ran, closed, then when booted up the next day I received the windows 32 error. I have an OEM windows xp installed in the computer, a pentium III gateway, and i understand that common recovery proceedures cannot be used with success, because the OEM versions have embedded passwords and such. I have not heard strange sounds from my hard drive, previous to , and subsiquent to the problem. I wish to run chkdsk,to see if this can resolve the problem, if the OEM version will allow it. Is this possible, and the fact that I have a D drive slaved to the c drive matter?
View 6 Replies View RelatedI went into BIOS and I found that my PC hard disk C & E are set as preimary disk both. Then the DVD-CD rom was set as escondary disk.So I try to make changes and when I start PC, Boot failure: System became Halted.What can I do? As a mtter of facts that why when I try to update WXP SP1 to SP2, the last one kick out disk E.
View 3 Replies View RelatedI am receiving the following error at startup: "Disk boot failure, insert system disk and press enter" There are no CD's in the CD drive. However, I ran the System Diagnostics and when it got to the Disk section - it is not recognizing the disk - it said Warning...and to check the cables. I have done that, and everything seems to be connected correctly.
View 2 Replies View RelatedMy Laptop running on windows XP Home just fails to boot up. It also does not start in the Safe Mode, (system freezes).When I tried to boot using the Recovery CD, the system just shuts itself down. If I try using the CD to boot, it simply shuts down after a few minutes.
When I try to boot Windows XP it says "DISK BOOT FAILURE, INSERT SYSTEM DISK AND PRESS ENTER" What do I do?
View 3 Replies View RelatedI recently was forced to do a re-install of XP to clean up a few bugs.The system has 3 hard drives, but since the reinstall, only the C: drive appears. The other two are nowhere to be found.I've tried mapping to them, but they just don't show up there as a mapping option.Anyone have any advice? When I added the extra hard drives I didn't have an available slot and did have to create a partition. I no longer have the software I had originally used though. Do I need it to make the 2 other drives visable?
View 1 Replies View RelatedI keep getting this error "One of the USB devices attached to this computer has malfunctioned, and Windows does not recognize it". And if I leave my PC on to long the keyboard, mouse, and sometimes even the monitor stop working. I've tried unplugging the keyboard and mouse (which are not USB) and plugging them back in, but to no avail.
View 8 Replies View RelatedNow I cannot boot without the 120GB plugged in (tried unplugging the drive and booting and it said the it was Unable to boot from disk or something). I eventually deleted the partition on the old drive in setup and then canceled setup, and I still couldn't boot. So I reinstalled winXP on the old drive and now it boots fine. Of course what I have to do is reinstall XP with the drive unplugged, but do I have to completely redo everything, or can I somehow reinstall without starting from scratch? I've tried using the setup disk in windows with the drive unplugged (I know it isn't safe to unplug drives with the computer running but I had run out of ideas), but it said that it couldn't reinstall windows because there was no valid System Partition (which is on the other drive.
View 6 Replies View RelatedI have installed a new hard drive and installed a new XP Pro on it. I kept the old XP Home for some time untill I'm happy with the new installation. The old XP Home was on drive C and the new XP Pro is on drive E. I am now ready to reclaim drive C disk space and tried formatting it. However, it appers as the "system" drive, while the new HD (E) appears as "boot". I realized I wont be able to format it until I make E drive system and boot together (which usually appears as "system"). Eventually, I would prefer that the new disk will be labeled C
View 1 Replies View RelatedI have an old T1090 eMachine that doesn't recognize the new larger hard drives. I purchased a 200 GB PATA (IDE) drive and it shows up as a 75 GB drive using GParted and under Windows Disk Management. I expected that it would only be recognized as 137 GB, but I can't explain why it only sees 75 GB. I suspect that the BIOS needs to be updated, but I've never done this before so I was looking for a procedure and ideas for trying to find the latest BIOS online.
View 8 Replies View RelatedI recently bought a new HDD because the old one appears ready to crash (clicking sound). My DVD-Rom is also dead, so I booted from the old hard drive & installed a fresh OS (Windows XP) on the new drive. However, I cannot boot from the new drive alone, because the 'system volume' is Drive C: (old drive) & 'boot volume' is Drive G: (new drive). How can I fix this? I don't mind reinstalling the OS, but I cannot boot from a CD & I don't know how long the old drive will last
View 5 Replies View RelatedI am unable to boot my PC most of the times.Whenever I switch on my PC,I see the following message nine ot of ten times. DiskError/Boot Faliure Reboot and select proper boot device or insert Boot media in selected boot device If I press enter after this messages & keep pressing following messages appear from time to time (Not simultaneously). If just after making the switch on, I press F2 key to check the boot device preference
If just after making the switch on , I press f11 key to reach the boot menu I always find the 1.44 MB Floppy option highlighted as the booting choice.(though there had not been any floppy in the floppy drive, I dont have any really)I make the hard disk option highlighted & it solves the problem only a few times. But next time when I try F11 key to check the boot menu again I find 1.44 MB floppy highlighted.
Getting error message when trying to change out a 10 gig to a 250.NVIDIA Boot Agent 201.0462 PXE-E61: Media Test Failure, check cable PXE-M0F: Exiting NVIDIA Boot Agent DISK BOOT FAILUR, INSERT SYSTEM DISK AND PRESS ENTER" this drive I am upgrading also has Windows XP OS. I have another drive on the computer that has 160g.
View 13 Replies View RelatedWhat can I possibly do to solve this problem? I have Windows XP and everywhere.
View 1 Replies View RelatedMy operating system is Windows XP Pro. As of yesterday all was fine, I even burned a DVD. Today "My Computer" isn't even showing my DVD/CD recorder, only showing Drive A: 3.5 Floppy. It started when I downloaded (I think) WindowsBlinds, just wanted to do some color changes. Well when I installed it, Norton came up with a Trojan. Norton Quarantined or deleted it and said no more further actions required. The install finished (windowblinds) and I tried a couple different skins and decided to uninstall it. Uninstalled with Revo Uninstaller
View 6 Replies View Relateda while ago my computer failed to boot repeatedly and I took it to the repair man who got it going but when I first switch it on I get the message invalide boot.ini file - booting from c and what has happened to create this problem and can I restore my PC to boot from the original file
View 1 Replies View Relatedmy computer just started having boot problems. I had not used it in a while because it was a backup. My primary has been totally taken over by a spyware program so I need to use the backup and now it won't boot up. All I get is the PXE_E53 no filename received message.
View 1 Replies View RelatedWhen booting up to Windows XP disc, i get an error screen that reads: Unmountable_Boot_Volume The problem is that the error screen appears before I can even get to the Windows Setup Welcome screen. So I can't even perform a recovery console procedure. I don't need the files on my hard drive anymore, I just need the computer working.
View 2 Replies View RelatedI recently loaded windows xp onto a gateway computer.It would not recognize the boot up disk so I loaded the Operating System on another tower and then put it back into this tower.Now it boots up to the MUP.SYS file and then freezes.Try booting computer in safe mode to the same results.It is a Gateway LP Minitower KAD Select 750 with an AMD Athlon Processor with 320MB of RAM and a 14GB hard drive.It has a 64MB Cache.
View 6 Replies View Related