i have a very serious problem with my pc when i start my pc it satys on dos ,and messages shows like press F1 to continue or press del to enter the setup now when i presss f1 it start the windows fine but when i press DEL nothing show up just a black screen thats all now problem is i cannot get to Bois setup to work it out
View 4 Replies
Hi. This is the second time it happens. I basically press the power button on the PC, all the fans started and then they shut off. I've pressed it again. The fans started to spin for a few seconds but no POST or successful BOOT Beep. After 30 seconds or so the PC finally boots. It gets past POST and the it sais something like this "Bad bios checksum. Recovering from backup bios". After a couple of minutes the PC started as usual and now I'm writing for it.Why is this happening?
View 6 Replies View RelatedI have 2TB SATA HDD for storage purpose and one SATA HDD for my OS, how can i setup my bios to be able to boot to my OS?
View 1 Replies View RelatedI have 2TB SATA HDD for storage purpose and one SATA HDD for my OS, how can i setup my bios to be able to boot to my OS?
View 2 Replies View Relatednot to enter bios setup
View 1 Replies View RelatedRunning a Dell XPS710. Was on the phone with tech support and had to go into setup to check on something. after I got off the phone, I rebooted and tried to access setup and can not. I don't know if I accidentally checked off something that won't allow me to use the keyboard until the machine boots into windows because pressing F2 (Setup) or F12 (Boot Options) when the Dell splash screen appears won't work. It just goes into Windows.
View 2 Replies View RelatedIm building this computer and now that I have all the pices Im trying to get it working. My problem is I cant get the bios set up right. I never had to do this befor so I dont really know what to do.
View 1 Replies View Relatedmy pc not go bios setup how to get into the bios?
View 1 Replies View RelatedAfter resolving an issue resulting from a printer installation, I was able to get my computer back to a state of normalcy, except that the CD drives were no longer found by the system.This is a Win 2K and there is a DVD-ROM and a CD-RW.So rather than do the smart thing and reinstall them via the OEM CDs, I went into the Bios and tried to tell the Bios that they were the Secondary Master and Slave drives (duh).So now, the system hangs, telling me that the primary slave auto detect wasn't finding anything. (Even though I didn't address that when I screwed with it.)I cannot even enter the BIOS setup, since the hangup occurs before the system even gets to that point.If I can get back to BIOS setup, I can at least reset to defaults, then figure out how to do the right thing, but for now, I'm STUCK.It's an MSI KT3 Ultra Mother board If more info is needed I can probably get it, but wanted to keep the initial post short.
View 1 Replies View Relatedusing windows xp how do I get in the BIOS Setup screen
View 1 Replies View RelatedThis article will have Bios and Windows settings that will help free up
resourses on non used devices. Note after going through these steps you may need to "Reset theConfigeration Data"(ECC Data). This will recycle the IRQs and free up the non used ones that might still being reserved by the motherboard.BIOS setup on my Micron Millennia TS doesn't explicitly list a reset configuration. How do I have the computer reassign the IRQ assignments?
is there a way i can open the bios setup for xp from the command prompt or is there aanother way
View 1 Replies View RelatedI am trying to access my system setup , So i can boot from my xp cd .I tried to hit F2 but it just keeps taking me to a black screen wanting my pw . I forgot my Pw and after trying to guess my pw to many times it now just shows a black screen wanting a pw ? How can i get pass this ? I have never seen this before .Need a Pw to get to bios setup?I cant boot from my cd unless i get into the bios setup .
View 3 Replies View RelatedI just finished assembling my new build. It boots and I can get to the BIOS. I even have it booting from the DVD drive so I can load Win XP.However, when I get to the Windows Setup and it asks me if I want to setup windows(press enter), Repair(some other key), quit(F3) my keyboard won't work. I hit "Enter" because I want to install XP and nothing happens. It is not responding to my keyboard strokes.
This is strange because the keyboard works in the BIOS.
once the on button was pushed, it came up with the BIOS screen asking for the password.I removed the CMOS battery, which allowed me to change the Password so I can get onto BIOS now. However, when I boot now it just comes up with the BIOS screen.I set HD to boot first, aswell as setting the clock and date. I then ask it to save and quit, after which it shut's down, and reboots, only, BIOS keeps coming up. And I need to get this sorted asap
View 14 Replies View RelatedI have had windows XP Pro installed, updated and running fine until about a week ago. I was away from home for about a week and left the machine plugged into the mains but powered down. When I returned home to boot up, it kept doing things like constantly hanging on parts of the bios POST screen, eventually booting up after thirty or so complete restarts. It finally booted into windows but after the last shutting down, it will now not boot up at all. I have replaced the bios battery and reset the bios several times.
View 5 Replies View RelatedWhen I turn on my computer, it does the bios check, then goes into the bios screen on its own. I have checked all of the bios settings, and see nothing set wrong. The only way I can get itno my xp pro system, is to use "F8" during the bios check, the select my hd from there, then it seems only half of my programs work, and it also seems to be randomly changing the programs that do not work, when I do this.
View 1 Replies View RelatedGot a bit of a problem with my housemates pc.A friend gave him some extra RAM, i checked it out and it was crucial 512mb pc2100 CL2.5, and although it didn't match his exsisting RAM it seemed to me that his mobo would only run the FSB at 200mhz anyway so i went ahead and fitted it.It worked fine I then noticed his system temp was running a little high (60-65 degrees), so i took his heatsink off and cleaned the dust and refitted it with some new thermal compound.I added too much and the temp went up. To nearly 90 degrees.I shut it dwon as i didn't want the cpu to pop, cleaned it off, reapplied less compound and figured this would work fine.Now we have the problem. Most of the time: Power on and nothing happens. No bios, no beeps. Occasionally: Power on, i jump into the bios, the temp looks fine (30-40 degrees) and then it freezes right there in the bios after about 30 seconds to a minute.This sounds like a heat issue, but the last temp reading before freeze is 33 degrees.?I've double and triple checked that the heatsink is on properly and thats fine. I followed the official guide on how much compound to use (a blob the size of an uncooked short grain of rice).
View 5 Replies View RelatedIm new to PCs and since my motherboard is three years old is it a good idea to upgrade? I contacted the maker of my motherboard and they say an upgrade is available and sent it to me for { DON'T CRACKUP} $49.00. I already read that you can really mess up your PC if you do one thing wrong when upgrading. Am I a fool for buying the upgrade? Please let me know as I can send the Floppy discs back.
View 2 Replies View RelatedI have ibm thinkpad R51 2887 nq2 series .My system has been crashed as it is not starting.The whole system gets hang after showing the first ibm screen. The bios utility setup is not getting opened through access ibm button . In safe mode it shows that system BIOS and video BIOS is not working and it has been shadowed.sometimes the system gets started ,but after one minute ,it stucks and the whole system paused and nothing happens.It may be the virus attack on BIOS and it also changes the time and date configuration of BIOS. so what should i do .And how i can install BIOS driver to the system.
View 1 Replies View RelatedI just flashed/upgraded my BIOS for my motherboard, and now XP doesn't even boot up.
After the BIOS load, I get a "MBR error 2" message and it just stays there.
My board is an Asus P5N32-SLI SE Deluxe. I used the Asus Update Utility to flash my BIOS.
I've setup Windows 2003 fax services on a W2K3 server and shared the device. I've tested faxing from Word on my PC and it works fine.However, when other users try to install the fax client, the setup hangs asking for the fx* setup files. I've tried different XPSP2 CDs, copying the files to a local directory, making sure that the users have local admin rights (and even domain admin rights) but to no avail. The files are already in the system32 directory so in theory the setup doesn't even need to copy them. Even if I delete them, it doesn't work.Our corporate SMS team reckons that there isn't any policy which could
cause the problem.
I started an upgrade for xp pro part way through the install I got a message "WatchDriverSigningPolicy.exe" no found I pressed enter then got another message "fake setup call himself instead original "setup.exe" ; setup abort!" now each time I reboot it starts to load xp then gives me the same message then press enter it then reboots.
View 3 Replies View RelatedI mistakenly launched XP Setup and want to know how to stop it from progressing further. I have another XP installed on another virtual disk. Rebooting from there allowed me delete the Setup files. Or so I thought ! The main XP installation however continues to try to launch Setup. Just about whatever I do, it ends in tears. My question is how do I stop XP on this disk from thinking it has to launch Setup? I dont want to reinstall XP, as that will involve a huge amount of work to recreate my environment.
View 6 Replies View RelatedI was told to reinstall windows 2000 aon a C800 I was given. I stopped with an erroro reading line 3221166496 hivedef.inf corrupted. Setup cannot continue.
View 3 Replies View Relatedi am trying to install windows office 2007 but after a minute from start of installation ,it popup dialog box saying setup can not find setup.exe file and say browse valid installation source and click ok.
I don't know whats happening.I have just formated my C drive and installed fresh copy of windows xp.
here is image of error message.
what should i do?
http://img101.imageshack.us/my.php?i...9005582dv8.jpg
i have a problem with my Acer Aspire 4732z. Press <F2> to enter SETUP).i must press anykey twice to load the window(i'm using window xp pro).i think it cause by System BIOS shadowed, i want to disable it..but there is no option.
View 2 Replies View RelatedI dropped my laptop the other day. It kept working at first, but crashed a couple of hours later. Now, when I boot-up, I get the following error message:"Windows could not start because the following file is missing or corrupt: System32/Drivers/Ntfs.sys. You can attempt to repari this file by starting Windows Setup using the original Setup CD-ROM. Select 'r' at the first screen to start repair."I've inserted the setup CD (in an external CD-Rom drive, since my laptop doesn't have its own drive). But for some reason, setup won't start, and I keep coming back to the above error message. How do I start setup?
View 12 Replies View RelatedMy Sony Vaio laptop running XP Professional suddenly one morning wouldn't boot up. Ctrl-Alt-Del will restart but goes no further. I can enter BIOS during this process, but nothing else responds. Can I get to a command prompt through bios in order to attempt a restore?
View 6 Replies View RelatedMy problem is my OS, which is XP home is seeing my master HD as a 20gb drive when it is actually a 40gb drive my slave is a 20gb drive and it sees it as 20gb. The BIOS sees the master as a 40gb drive and the slave as 20 gb.
View 2 Replies View RelatedI keep trying to access BIOS by tapping F2 or DELETE or F10 but the boot continues like no keys were tapped. Except for that, the computer functioning normally. Can someone tell me how to change it back to normal.
View 14 Replies View Related
