My computer is often showing blue screens and nothing I've done seems to correct the STOP 0x00000050 error about "page fault in the non_paged area". So I guess is time for me to back-up everything ASAP. Which I never did. Because I don?t know how. Could someone with good will guide me on the steps to get an EASY & SAFE back up using CD's ?
View 14 RepliesSTOP 0x00000050 (0x8CCC1345, 0x0000001, 0x808A65A1, 0x00000000) These both happen when installing windows, either when at 95% of copying files or when booting into windows.
View 7 Replies View RelatedI am getting a BSOD and the error says: PAGE_FAULT_IN_NONPAGED_AREA STOP: 0X00000050 (0X81000078, 0X00000000, OXF9E129BD, 0X00000002) spooldr.sys - address f9e129bd base at f9e11000, datestamp 469e788d I tested to see what drivers are not digitally signed because I read somewhere to check that and it said that the omci.sys and tcpip.sys are not digitally signed. I am testing all the hardware as we speak with PC-CHECK, the RAM seemed to pass all the tests. I can log in to safe mode and I tried restoring to a previous date and it worked for a while. I was able to uninstall the McAfee Antivirus which I thought might be the problem, but still BSOD...
View 14 Replies View RelatedNT Backup is, by default, installed only with XP Pro.To install it in XP Home Editon doubleclick this file on your XP cd:VALUEADDMSFTNTBACKUPNTBACKUP.MSI.Start>run>NTBACKUP.
View 9 Replies View RelatedI have a backup.reg file (C:Documents and Settingsmy nameMy Documents eg backup.reg) that is 82MB that still has fragments after being defragged. I would like to simply delete this file since it's been a few months since I made the backup, and I'm not experiencing any problems with my registry. Is it safe to delete this backup?
View 13 Replies View RelatedMy computer seems to work fine except when I try to do a copy in Casper XP to backup my hard drive to external HD. I also got this stop code last night when trying to do a disk check to correct errors. Stop 0X0000000A (0X00000188, 0X000000FF, 0X00000000, 0X804E35E9). I have located online page for stop 0X0000000A codes which states could be driver problem... that last one parimeter 4 -- 804E35E9 how/where would I
find out which/if this is associated to a particular driver so I can possibly correct it?
My computer won't stop booting in safe mode and I can't change it. I have no idea where to start.
View 8 Replies View RelatedIn trying to get rid of some adware, I attempted to boot my computer (P4 2.8 GHz, 1.5 GB Ram, Windows XP SP2) in safe mode. When I selected "Safe Mode with Networking", I was brought to a blue screen called a "STOP ERROR SCREEN" - basically it said that it had to stop the booting up of the computer or the computer might be harmed. It suggested removing any recently installed hardware and disabling BIOS memory options such as caching or shadowing. So I rebooted and got into windows normally just fine.
Then I decided to try just regular Safe Mode (without networking) - when I selected that option, the computer started to do it, then rebooted and prompted me if I wanted to boot into Windows normally or safe mode, etc...I tried Safe Mode again - same thing, a reboot. I tried Safe Mode with Networking again - and I got the blue Stop Error Screen again.
This is pretty strange (at least I've never seen it) and I'd really like to be able to boot into safe mode.
The problem is on my buddies pc. It uses Windows XP Professional. I have it setup next to this pc I'm currently using. First I get this screen:
We apologize for the inconvenience, but Windows did not start successfully. A recent harware or software change might have caused this.
If your computer stopped responding, restarted unexpectedly, or was automatically shut down to protect your files and folders, choose Last Known Good Configuration to revert to the most recent settings that worked.
If a previous startup attempt was interrupted due to a power failure or because the Power or Reset button was pressed, or if you aren't sure what caused the problem, choose Start Windows Normally.
Safe Mode
Safe Mode with Networking
Safe Mode with Command Prompt
Last Known Good Configuration (your most recent settings that worked)
Start Windows Normally
Use the up and down arrow keys to move the highlight your choice.
Any choice I highlight brings this screen:
A problem has been detected and Windows has been shut down to prevent damage to your computer.
If this is the first time you've seen this Stop error screen, restart your computer. If this screen appears again, follow these steps:
Check to be sure you have adequate disk space. If a driver is indentified in the stop message, disable the driver or check with the manufacturer for driver updates. Try changing video adapters.
Check with the hardware vendor for any BIOS updates. Disable BIOS memory options such as caching or shadowing. If you need to use Safe Mode to remove or disable components, restart your computer, press F8 to select Advanced Startup Options, and then select Safe Mode.
Technical information:
*** STOP: 0x0000007E (0x80000003, 0xF8470005, 0xF894C4B4, 0xF894C1B0)
*** SCSIPORT.SYS - Address F8470005 base at F8460000, DateStamp 41107b4b
An app was installed, and right after, a BSOD came up with the following error message: A problem has been detected and windows has been shut down to prevent damage to your computer. If this is the first time you've seen this Stop error screen, restart your computer. If this screen appears again, follow these steps: Check to be sure you have adequate disk space. If a driver is identified in the Stop message, disable the driver or check with the manufacturer for driver updates. Try changing video adapters.
Technical information: *** STOP: 0x0000008E (0xC0000005, 0xBF803EF6, 0xF70917c4, 0x00000000) *** win32ksys - Address BF 803EF6 base at BF800000, DateStamp 43446a58 Beginning dump of physical memory. Physical memory dump complete. Contact your system administrator or technical support group for further assistance......
I cannot boot to Safe Mode. Using F8 at logo display, I can select Safe Mode, but never get there. Using F12 at logo display, I can boot to Utility Partition to run Express, Extended and Symptom Tree diagnostics which include Cache, Interrupt Controller, System Memory, and HD tests WHICH ALL PASS!! The BSOD error message is: A problem has been detected and Windows has been shut down to prevent damage to your computer. Error info: Stop: 0x0000008E 0xC0000005 0xBF89066B 0xF3F5CAF0 0x00000000 Win32k.sys ADDR BF89066B base at BF800000 DateStamp 3f1487db The OS is Windows XP SP1a. Only the CPU and Monitor are connected.
View 14 Replies View RelatedI have never helped anyone with windows 2000 or 2000 Pro before. When you start the computer it is a blue screen with txt and starts out saying a stop error
Stop:0x0000007B (0x81872030,0xc000014F,0x00000000,0x000000007 INACCESSIBLE_BOOT_DEVICE
Then it says ot run a virus scan and chk disk etc but I can't get into normal or safe mode to do that, when you press F8 to get into safemode it comes up and you press enter then the next screen for windows you press enter then it ends up back at the blue screen witht the error again.
It started yesterday, I was playing around on the computer and only downloaded magiciso.I continued to play around. I shut down the computer and it hasnt been the same since.When it 1st started back up..I got this:Address 80410527 base at 80400000 datestamp 45069e6e - ntoskrnl.exe IRQL not less or equal I tried to get into safe mode but nothing.I then tried last good config and it let me in...so I played around to what I thought would fix things..but when I restarted it again..it wont let me in either way now.
View 2 Replies View RelatedI have a friend who has a Dell Dimension 2400. She had a blue screen error with the following parameters 0x00000050 (0xfa3bedeb, 0x00000000, 0xfa3beded, 0x00000000). She was able to reboot at the time of the error but now she's getting a black screen and can not do anything at all.
View 8 Replies View RelatedWhen I start PC, it automatically takes me to the startup options part to reboot in safe mode, safe mode w/ networking, safemode w/ prompt, last known good config, & normal startup. Getting Stop c0000218 {Registry File Failure} The registry cannot load the hive (file) SystemRootSystem32Config
View 11 Replies View RelatedAfter restoring a computer and backing up files, once the computer is back up and running should I have a foldercalled "My Backup 1408-08 2353" or should I have a single backup file called backup.bkf? I'm trying to help someone, and they have a folder with the files already available instead of a single backup.bkf file. He wants to restore everything to the original location before the computer restore. How can he do that with the folder he has instead of a backup.bkf file? The restore wizard is asking for a .bkf file to place everything in the original locations, and he doesn't have that.
View 11 Replies View RelatedI want to backup my PC for disaster recovery and then do an incremental backup each night to a USB hard drive. I tried Retrospect which came with the USB hard drive. I couldn't get it to work to well. I've been using the MS backup utility. With this software it seems any new email causes changes my large Outlook PST file and the whole
file is backed up again. I've been trying to find backup software which will backup just the changed elements of the pst file and have tried downloading a trial version of
continuity@work from Mobiliti who claim to be able to just backup the changes to a PST file. I left continuity@work running overnight and had to stop it as it was only 50% through the backup this morning. It calls it synchronization rather than backup and from the error messages it seems that it doesn't create a shadow image before backing up as several files were not backed up as they were in use.
I have two IDE hard disks one 40GB=C and the secondary 200GB=D,I have made a copy of documents and setting from C to a new folder backup in drive D.After that this operating finished I preformed format of C and installed from on drive C the MS WIN XP operating system.After the installation the backup FOLDER on drive D, changed to backup FILE without extension.How can I restore my DATA? anyone familiar with this phenomenon
View 3 Replies View RelatedI'm getting a random blue screen crash and was wondering if anyone could give it a shot. It's a 0x00000050 crash, Heres the crash dump file.
View 9 Replies View Relatedbasically what im looking to do is delete some old entries that the XP backup utility has created over time that i setup a while ago. Im using the "copy" option.so nothing has been appended or incremental.Im just looking to avoid deleting the setup i got, and maybe just delete a few "copy" backups so that theres not 8 gigs / 1 years worth of backups.i only need about 4 months I forgot about it.cuz i never neaded it. But it looks as if its the only way b/c i cant just delete selected backups.all or nothing?/ anyone know of a better backup utility that is simple and easy on a system BTW?
View 11 Replies View RelatedWhen scheduling a backup using the Windows Backup Wizard, I put in all the scheduling info, but Windows backup never launches. When I look at a scheduled event and click "properties" I get an error message that says "General page initialization failed, etc, etc. (error# 0X80090016)
View 2 Replies View RelatedUse this if you just want to display your IP address and not the extra information (default gateway / subnet mask)Simply copy and paste the following into notepad@echo.@ipconfig | find "IP Address"@echo.@pauseAnd save as IP.BAT (save to your windows dir if you want to be able to access it anywhere)Now when you type IP you will see:---------------------------IP Address. . . . . . . . . . . . : x.x.x.xPress any key to continue . . .---------------------------(information about the code: @echo. produces a blank line, @ipconfig | find "IP Address" causes the output of ipconfig to be piped to the find command, which looks for the line containing "IP Address", find then outputs your IP address, @pause causes the terminal to wait for user input before continuing. The @ before each command tells the terminal not to echo the command being typed.)
View 9 Replies View RelatedI'm saving picture and video files on separate DVD-RWs. I have Easy CD Creator 5x basic that came w/ the computer and updated it with the patch 5.3.5.10_basic. I pulled my first DVD from a year ago out and added pictures onto it from this year's trip. Original files were there as expected and additions were no problem. Secondly, I started a 2nd disc of all video wmv files. I filled that one to the hilt and do not wish to add to what little room is left.My settings are set thusly: "The selected Record Method finalizes the session. The CD itself is not finalized so additional sessions can be added later. To change this setting click options."Actually, this is the setting I prefer, but in the case of the second disc, it's full for me now and if I wish to possibly play it on my DVD player it needs to be finalized.Problem is, this option isn't available (appears all faded-out) when I click on file, and appears the same to the lower right when I'm looking at disc properties. Only real option in bold black at these times is ERASE, and I don't want to do that! The discs play great on my computer, all material is recognized, etc., but this inability to finalize has me confused. Certainly in theory, a RW disc by its nature will never be truly finalized. Is that what's holding things up? I do believe I should be able to finalize these,
View 3 Replies View RelatedAn easy way to hide the Recycle Bin is just to create two .reg files.... open your notepad and copy and paste the listing below and save it as Hidebin.reg and click the .reg file to enter it into the registry. You have to refresh the desktop to see the changes.
REGEDIT4
[HKEY_CURRENT_USERSoftwareMicrosoftWindowsCurrentVersionExplorerHideDesktopIcons]
[HKEY_CURRENT_USERSoftwareMicrosoftWindowsCurrentVersionExplorerHideDesktopIconsClassicStartMenu]"{645FF040-5081-101B-9F08-00AA002F954E}"=dword:00000001
[HKEY_CURRENT_USERSoftwareMicrosoftWindowsCurrentVersionExplorerHideDesktopIconsNewStartPanel]"{645FF040-5081-101B-9F08-00AA002F954E}"=dword:00000001
Â
To bring back the Recycle Bin, open notepad and copy and paste the listing below and save it as Showbin.reg and click the .reg file to enter it into the registry, once again refresh the desktop to see the changes.
REGEDIT4
[HKEY_CURRENT_USERSoftwareMicrosoftWindowsCurrentVersionExplorerHideDesktopIcons]
[HKEY_CURRENT_USERSoftwareMicrosoftWindowsCurrentVersionExplorerHideDesktopIconsClassicStartMenu]"{645FF040-5081-101B-9F08-00AA002F954E}"=dword:00000000
[HKEY_CURRENT_USERSoftwareMicrosoftWindowsCurrentVersionExplorerHideDesktopIconsNewStartPanel]"{645FF040-5081-101B-9F08-00AA002F954E}"=dword:00000000Â
If you need to re-install a hidden Windows component, there is an easy way to do this. Open the INF folder in your windows folder [C:WINDOWSINF] Find the *.inf files. Find the application title you need in the filename [for example messenger is msmsgs.inf] If you are unsure of the installer, RIGHT CLICK on the file, then select open, at the top of the file should say what application it is:; MSMSGS.INF; Setup INF file for Messenger When you have found the file the right click on it then click install.Tip: To reinstall Microsoft Outlook Express, Right click and select install on MSOE50.inf.
View 9 Replies View RelatedI found a Guide to Easy To Remember Strong Password on this site
Now i am curious to know how long should a password be
Also please suggest your ideas of Secure password
I have updated to win xp from win me. The Adaptec Easy CD Creator will not work as a message comes up saying "Drivers are not compatible and could cause problems" so they don't load when I have reinstalled the program.This came with my computer when I bought it with win ME. I have the original disk. I have looked at the web site which now is Roxio, but cannot get a straight answer as to what and where the drivers are to download. They keep wanting me to buy their ver. 10 which is $70. All I want is the program I had before no fancy technical program. I just copied some floppy's and cd's. I don't need all that photo stuff that is on the new program. Also do not need to copy DVD's.I read about registry, but don't want to mess with that after getting my computer running smooth now that I have the Win XP installed.What drivers do I need? When I find a web page their are so many I don't know what to do.
View 1 Replies View RelatedI have Roxio Easy CD Creator but can't burn MP3s to a CD. The Roxio Drag and Drop always has the CD drive locked. I get an error in Easy Cd Creator about this. I can't find any way to turn off Drag and Drop.
View 1 Replies View RelatedI am looking for a free PDF creator program that is easy to use. I need to deploy this on about 50 PCs in my office and it needs to be idiot proof, I looked at some of the open source PDF creators and they work well but have too many options for users to screw up. I just want something that lets you print to the PDF printer and then save the file as PDF.
View 8 Replies View RelatedI installed XP Pro 64-Bit to run alongside my Windows 7 install - unfortunately XP did not detect Windows 7 and I used EasyBCD in XP to create the start-up dual-boot entrys...windows 7 (C) - default Windows XP (E)
3 seconds
Instead of going into the register, it is simpler to open Windows Explorer, find the .exe file that you want, right-click on it and choose send to desktop.
View 9 Replies View Related