Will Restore Cds Work As Dual Boot ?
Jul 2, 2009
When I can afford it, I'm getting another gateway with Windows 7.
I have a gateway laptop m-6881 w/ vista 32bit HP sp2. (8/2008)
I also have a gateway tower S500 XP Pro 32bit SP3 ( 3/2003)
The laptop has 3 restore DVD's with the OS on it (sp1) - also other programs and drivers.
The tower has 4 restore CD's with the OS on it - including 2driver cd's, 2programs cd's.
Can I use the restore CD from the XP or/and vista machine on my Windows 7 machine as a dual boot as long as I wipe the HDD of the XP machine and toss it? ( since all are gateways )
I no longer want to use my XP,win2000 or win98 rigs anymore.
I'm going to wipe the HDD and give them away.
This may not make sense but I can't get my fingers to type what I'm trying to say
{Dell laptop win98 and a Dell win2000 tower - I don't even boot them up anymore}
View 9 Replies
ADVERTISEMENT
Aug 8, 2012
I have dual boot with Xp and windows 7.when i log into my Xp all the restore points being deleted from windows 7.when i check the disk management information in 7 it shows windows 7 create a logical drive with my Xp primary drive.even i am hide the drive from both windows means Xp drive from windows 7 and vice verse.So i like to unmount or remove the drive partition of windows 7 from Xp and Xp primary from windows 7.So that they dont affect each others system files with being deleted the partitions.
View 1 Replies
View Related
May 12, 2009
I just installed Windows 7 as a dual boot with my XPsp3. Now my Logitech Revolution VX mouse has lost all its special functions, and the Setpoint software in unable to work properly.
Any thoughts? The same thing happened when I set up Ubuntu as a dual boot - finally removed the linux.
View 0 Replies
View Related
Dec 13, 2012
I just purchased a new video card for my old Acer M3100 that I dual boot the original Vista and Windows 7 on. I bought a new Asus Nvidia GeForce GT 610 video card to play Skyrim. Windows 7 will install the drivers with absolutely no error messages but upon rebooting they won't load and I'm stuck with basic VGA. I booted out and back to Vista and loaded them and they installed fine as well and upon rebooting into Vista they actually load! My Windows 7 install is a recent clean install because I tried upgrading to Windows 8 and didn't do a clean install and it borked itself on all my legacy hardware. Does anyone know why a clean install won't load new video card drivers but my old Vista install loads them fine? (Yet another reason not to abandon the Vista Beast, Vista is the last OS that recognizes my (2) Rio Karma MP3 Players.)I downloaded the latest drivers for Windows 7 Pro 64Bit directly from Nvidias website and installed them and still get a "No GPU detected" message when trying to run the NVidia software that comes with the drivers.
NVidia Driver Version: 306.97
View 7 Replies
View Related
Jan 1, 2013
I have recently installed windows ultimate x64 on my computer.i have an asus p6t deluxe v2 mobo, i7-960 cpu and a wd velociraptor hdd. The install went ok, I even managed to restart my computer a few times after but after windows updates installed it won't boot. I tried to boot into safe mode, restore from the installer, and repair, none worked. After startup repair it says: "a patch is preventing the system from starting" and I get a 0x1f error code.(Preventing windows from downloading any updates didn't work either)
View 9 Replies
View Related
Oct 19, 2012
Did a system restore in Windows 7 and my dual boot system (Windows 7&XP) won't boot. It's looking for a boot device. When I put in a Hiren boot 10.6 disk, the dual boot option is one of a number of alternatives, and it allows me to get into my pc. How can I get back to having the system work like it did before? So it boots to the dual boot option without Hiren.My SSD drive is the main drive for Windows 7 &XP. It has two partitions.
View 1 Replies
View Related
Sep 12, 2011
i have a new work laptop with xp sp3 on it. I want to install w7 64 bit as a dual boot, but only have 1 physical drive. i cannot remove my current installation as it is pre-build from work, but can partition the drive etc. However on trying to install w7 64 bit I get a message saying cannot install windows 7 on efi drive with mbr, not gpt. Can I do what I want without screwing up my xp installation?
View 5 Replies
View Related
Feb 4, 2011
dual booting windows 7 home premium x64 with linux fedora 14 on dual independantly dedicated drives. i am a college student with moderate computer (windows) knowledge but am doing software development and would like to play around with some linux for a class. i have no prior experience with linux and have minimal knowledge of operation. i am currently running windows 7 and would like to keep it as my primary os. i do not wish to share media files across drives or os's, windows does that just fine as is and i dont want to get into a third drive. my current drive is a 1tb wd black caviar hdd. it is also currently 2/3rds full and the desktop is about 6 months old so i would rather not partition the drive for a dual boot. i would think that there are some other advantages for the os's operating independantly off their own drives other than if one hdd dies i should still have the other with its os still ok. i have read some topics about RAID configs with dual boot setups with dual drives like this but am not very familiar with RAID. is there a RAID config that would be beneficial in this situation? i currently do not have a RAID card. my tower internals are not very accessible and i dont like the idea of disconnecting drives depending on which os i want to operate.
View 5 Replies
View Related
Nov 12, 2009
As currently configured, XP is on drive C:, Win 7 was added to drive E:, and the system is currently run as a dual boot. Attempting to boot without the XP drive present will yield a "NTLDR is missing" error very early in the boot process.
I have already tried the following:
(1) I moved the hidden Windows Boot Manager files (bootmgr as well as the associated Boot folder) from the XP drive root to the Win 7 drive root.
(2) After physically removing the XP drive, I rebooted to the Win 7 installation DVD, and used the "Repair Your Computer" option to pull up the "Recovery Tools". Then, using the command prompt utility, ...
(3) I attempted to write a new boot sector to the Windows 7 disk using the command: Bootrec /fixboot, - that yields an error though. The Bootrec /fixmbr claimed success, but ultimately did not make Win 7 drive bootable.
I had to reconnect drive C: just to boot into Win 7 again to write this. I do have files backed up, but to format and reinstall files would take many hours beyond just the time to transfer 400 GB of data, since I have dozens of purchased applications that need to be freshly reinstalled and validated as well. Basically I want my E: drive now to be my boot drive while the C: drive is reformatted and used for general storage.
Any idea how to make my Win 7 drive bootable? Do I need a partition program that is more adept at creating a viable boot sector, or is that even the problem?
View 9 Replies
View Related
Jan 2, 2010
I have Win XP 32 bit on my old drive. I buy Win 7 full retail and a new HD. I set bios to boot from cd etc. Win 7 starts up. It shows the 2 drives, so I select new drive...no problems. It starts install. I leave it to do its stuff.When I come back its up and all ok.I dint get any option to boot from XP. The drive was listed as "SYSTEM" but not old Windows or anything.
Also ASUS chipset drivers dont work and they were listed as 7 drivers.I tried Vista drivers but it normally shuts down and restarts. Nothing.
View 9 Replies
View Related
Dec 28, 2009
I came home from work today and both my monitors were completely black even though computer was up and running. Browsing through my iphone I noticed that dual monitors were a possibility. So I unplugged one and restarted with success.
I then proceeded to update my video drivers (I have a nvidia 6800) but the problem persists.
Any ideas??
View 9 Replies
View Related
Dec 27, 2010
I have a strange problem with 2 displays connected to my ATI HD4770 Video Card running the latest 10.12 drivers and AMD Control Center.
I have 2 displays connected to the card.
The display 1 (Samsung Syncmaster 225BW) runs at 1680 x 1050 and is the Main display with the Windows 7 Start Menu.
The display 2 (Phillips Brillance 230W) runs at 1920 x 1200. Physically it is located on the left side of display one.
I arrange the display either by using the Display / Screen Resolution Control Panel Applet or the Catalyst Control Center Desktops & Displays Applet.
Both works fine (drag display 2 to the left side of display 1, chance resolution from 1680 x 1050 to 1920 x 1200.
But when I restart my machine, after the reboot has finished and the desktop appears, my display settings are exactly as before the reboot.
But when Catalyst Control Center loads, it switches the display and reduces the resolution of the bigger one to that of the smaller main display.
Every time I have to manually restore my custom display settings (Arrangement, different resolution) Is there someone in Windows 7 forum which is expert for ATI and CCC running multiple displays in handling those glitches?
View 5 Replies
View Related
Aug 31, 2012
my Windows 7 64-bit computer acted oddly (after it accidentally got unplugged while on, tho not sure that's what did it). now when i boot i get as far as the windows 7 logo starts to show, then i get that it can't boot.
i changed nothing that i know of. repair says it can't. restore, which only lists points from 3 days ago, doesn't work. i did a memory test. it was fine. am i doomed to do a clean re-install of Windows 7?
btw, if i get that Windows 7 logo, and also a stage where it says it is loading files, that means it is reading from my hard drive, right?
View 5 Replies
View Related
Aug 31, 2012
my Windows 7 64-bit computer acted oddly (after it accidentally got unplugged while on, tho not sure that's what did it). now when i boot i get as far as the windows 7 logo starts to show, then i get that it can't boot. i changed nothing that i know of.
repair from my bootable Windows 7 disk says it can't. restore, which only lists points from 3 days ago, doesn't work. i did a memory test. it was fine.
am i doomed to do a clean re-install of Windows 7?
btw, if i get that Windows 7 logo, and also a stage where it says it is loading files, that means it is reading from my hard drive, right?
View 1 Replies
View Related
Jul 28, 2011
I can't get system restore to work all the way.I keep getting error messages. The first error message said this:"System Restore did not complete successfully. Your computer's system files and settings were not changed.System Restore failed while mounting the registry from the restore point. An unspecified error occurred during System Restore. (0x800703f1)".A different error message was saying that Restore didn't work because it failed to extract this file: C:Program Files (x86)AdobeAdobe Premiere Elements 7.0x0407.ini So, I booted into safe mode and I deleted every single Adobe Premiere Elements file on my pc. Then I tried to do system restore again, this time from safe mode - but restore still didn't work. I keep getting the same error message. I have tried all the other restore points, with no success.Also, if this info helps - last week I installed a new internal 2TB Hard Drive onto my computer - it's the "K:" drive. A few days later I was getting ready to create a regular Restore Point, like I do every few weeks. But that's when I noticed that "System Restore" now shows two drives "C:" and "K:", and "K:" was greyed-out. So, I clicked the "Configure" button to configure the "K:" drive.
So, I wasn't sure that if the act of configuring the "K:" drive might have caused this whole - not being able to Restore issue. For example, by adding a new hard drive and then "Configuring" the drive, so that System Restore can work/talk with the new drive - did that somehow give System Restore a split-personality disorder? [code]
View 14 Replies
View Related
Feb 20, 2012
setting up a brand new computer. had dual monitors before. go to add the second monitor and the computer will not even recognize it is there.
View 5 Replies
View Related
Oct 14, 2009
I installed Windows 7 on a partitioned harddrive with vista on the other half. After the installation i have my boot menu with:Windows 7, Windows Vista, Windows vista still works but when i try and load windows 7 i get a boot error message
View 9 Replies
View Related
Oct 30, 2009
I have XP (x86) installed on one partition.
Last night I installed Windows 7 (x64) on a separate partition.
Anytime I had tried this in the past, using Vista, it always detected the Windows XP partition, and gave me a boot menu with "Earlier Version of Windows" option to boot to.
This is not so with Windows 7.
How can I get the boot menu to show both options, to boot to XP or to Windows 7?
View 9 Replies
View Related
Dec 7, 2012
all the icons on my screen have gone white and i cant click anything not even the start button. when i bring up the task manager all it is is a white box. i can login in fine but that is it. when i try torestore nothing happens, i dont have any restore points so i dont want to do a complete restore if i can avoid it. i have tried running chkdsk in safe mode but nothing has worked. i have also run avg rescue cd form a usb and it identified a trojan but i deleted it, still no effect. i have also tried using the recovery cd i got with my samsung laptop but can only use the startup check tool. this comes back with no issues but i cant use any of the other options.
View 2 Replies
View Related
Apr 18, 2011
I have a Compaq Laptop It run on Windows Vista Home Premium 32bit. It is having this problem that the wireless internet won't connect, I have done system restore so many times and every time it still won't work, sometime it will.
View 3 Replies
View Related
Aug 17, 2012
I am running windows 7. when i try and restore to a different time it fails.Whats up? Yes it is turned on with lots of disc space.
View 3 Replies
View Related
Aug 11, 2010
I have 3 drives, C:, D:, and E:. E: is just a storage drive. XP was originally installed on the D: drive. I installed Windows 7 on the C: drive following the instructions at Dual Boot Installation with Windows 7 and XP. After installing Windows 7, I didn't get an option to boot XP so I used EasyBCD to add an XP entry to the boot menu. That worked, but after I boot into XP, if I shutdown or restart I get an error message about the Windows Boot Manager that says
"Windows failed to start. A recent hardware or software change might be the cause. To fix the problem
...
etc
...
File: ootcd
Status: 0xc000000f
Info: an error occurred while attempting to read the boot configuration data."
Then I have to run startup repair from the Windows 7 disk. But then I just get stuck with Windows 7 and no boot menu entry for XP. If I try EasyBCD again, the same process results.
View 4 Replies
View Related
Apr 6, 2012
I installed opensuse 12.1 on dual boot along with my other windows 7 installation. Installation of opensuse is successful and i can use it. But when I tried to use windows 7 on grub, it says bootmgr is missing. I've already encountered this problem a long time ago so i tried to use bootrec /fixmbr, bootrec /rebuildbcd and bootrec /fixboot in the recovery console in the windows 7 DVD. Rebuildbcd and fixboot did not work and it said something like it cannot find my windows installation. I also tried bootrec /scanos, it returned a windows installation on D:\Windows but my windows is in drive C. I think this has something to do with me messing up the active partition in disk management a month ago but i already fixed it by setting the active partition to the system reserved partition. Only fixmbr is successful, but now i can't boot on any OS because it says: Missing operating system.I also tried bcdboot C:\Windows but it failed with a message that goes like: Failure when attempting to copy boot information..
View 2 Replies
View Related
Sep 24, 2009
I was having win 7 RTM and i tried to installl OSx86 in second hard disk
after few failure i successfully installed OSx86 in my secondary had disk now the problem is that i cant boot win 7
i changed boot order i tried windows 7 disk repair
but both failed
im getting some Boot mldr missing...
Actually even OSx86 is not booting i get OSx86 boot screen with two hard disk to select if i select windows disk it still says the same Boot mldr missing.
View 3 Replies
View Related
Dec 3, 2010
I can't get Win 7 to boot after setting up dual boot (Ubuntu 10.10) on my GF's laptop. I'll describe the problem and everything that has been tried so far. REALLY hoping somebody has an idea, I'm getting desperate.I installed Ubuntu last night via the Live CD. Used the Live version to install alongside Windows and partition the drive, install Grub, etc. At reboot, after POST it would just go to a black screen with a flashing cursor. I could only run off the live CD. A forum member determined the Grub was trying to load from the wrong partition. We changed that and voila! Grub now loads properly. I can boot into Ubunto via Grub with zero problems. HOWEVER: when I try to boot into Win 7 from Grub, it just locks at the same flashing cursor of death screen. The 7 partition is till intact, I can see and access all the files on the 7 partition from within Ubuntu, however 7 will not boot. I have tried downloading and burning the Win 7 repair disk and doing all of the following,Running the automatic Start Up Repair - several times. All it does is remove Grub, but booting still goes to the flashing cursor and I have to reinstall Grub again to be able to do anything after POST.I have used the command prompt to run "bootsect /nt60 SYS /mbr". Has the same effect as above.I have used all the bootsec.exe /fixmbr, /fixboot, and /rebuildBCD commands. Again, all have the same effect and I have to reinstall Grub to get anywhere.I don't have an installation disk to try and just do a repair install because Asus apparently doesn't feel that I would need one of these. All I have is the recovery disks from the Asus AIRecovery application that want to just re-format the entire drive and start over. This isn't an option. It's my GF's laptop (mine gave up the ghost last week) and we both have WAY too much highly important data on here. Not to mention she would castrate me . Now from all my research the only other thing I've come across that sounds possible is that the boot flag needs to be set to a different partition. Somebody had a somewhat similar problem and it turned out the way Dell set up the system the boot flag had to be moved to a recovery partition and it worked fine. I'm wondering if Asus has something similar going on, but I can't figure out how to move the boot flag. I'm going on 12 straight hours of working on this now
View 9 Replies
View Related
Aug 27, 2009
I setup an XP/Windows 7 dual boot on two drives. Currently C: Windows 7, D:XP
Love Windows 7 and now I'm ready to convert to single boot Windows 7.
I'm not real savy re. bcdedit so will need very detailed instructions
I did find the command line in Windows 7 by going through accessories but I'm scared to go further without help.
Eventually I want to clean up the D:xp and use it for storage etc.
I'm guessing this procedure may have already be written up but I can't seem to find it.
View 9 Replies
View Related
Mar 11, 2009
How to Change the OS Name in Windows Boot Manager ?
View 0 Replies
View Related
Apr 20, 2011
I have just installed a 3TB external drive for backup purposes and was testing the image restore feature. If I use the external drive on the usb 3.0 port when entering F8/System Repair/Repair from image, the drive is not detected at all, when I plug it into the 2.0 port it is detected. Within windows itself the drive operates fine on the 3.0 hub. I am guessing its some kind of USB 3.0 driver issue within system repair but wondered if there is a work around. Not sure I want to sit and wait for a restore over 2.0 when it could be using 3.0!
View 9 Replies
View Related
Aug 9, 2012
I'm running Windows 7 Home Premium 64bit. When I try to do a System Restore, it seems to run to completion, reboots the system and then issues the following message:
"System Restore did not complete successfully. Your computer's system files and settings were not changed."
Same result in Safe mode. Same result with AV disabled. (Kaspersky Internet Security 12)
View 6 Replies
View Related
Feb 13, 2012
I was contemplating using a Raid 0 array as my primary C: drive with OS. I understand all the issues with that and do regular daily backups. I used to use Acronis which had no trouble with a raid array. But on this new build I was wondering if the built in backup tools would be able to image and more importantly restore my data to the array. My back up drive is not part of the array. I would guess that it would see it just fine from the OS and have no trouble creating the backup image, I am more concerned that if I had to use the rescue disk and reload the image whether or not the array would be visible to the restore disk.
View 8 Replies
View Related
Jul 24, 2012
Ever since I removed some malware I cannot run a program that is vital to my job. It tries to do a software update (which it does periodically) and encounters this error: "Message 0x1047 in SUBVMCHK Another application is in the process of updating. Please wait while this update completes." I click ok and the program shuts down. I cannot uninstall the program (I get error 1060). Is there a registry key missing? Earliest system restore does not work.
View 3 Replies
View Related
