Windows 7 Does Not Restore Dual Display Config After A Reboot
Dec 27, 2010
I have a strange problem with 2 displays connected to my ATI HD4770 Video Card running the latest 10.12 drivers and AMD Control Center.
I have 2 displays connected to the card.
The display 1 (Samsung Syncmaster 225BW) runs at 1680 x 1050 and is the Main display with the Windows 7 Start Menu.
The display 2 (Phillips Brillance 230W) runs at 1920 x 1200. Physically it is located on the left side of display one.
I arrange the display either by using the Display / Screen Resolution Control Panel Applet or the Catalyst Control Center Desktops & Displays Applet.
Both works fine (drag display 2 to the left side of display 1, chance resolution from 1680 x 1050 to 1920 x 1200.
But when I restart my machine, after the reboot has finished and the desktop appears, my display settings are exactly as before the reboot.
But when Catalyst Control Center loads, it switches the display and reduces the resolution of the bigger one to that of the smaller main display.
Every time I have to manually restore my custom display settings (Arrangement, different resolution) Is there someone in Windows 7 forum which is expert for ATI and CCC running multiple displays in handling those glitches?
View 5 Replies
ADVERTISEMENT
Nov 29, 2011
Every time I rebooted my laptop windows runs through preparing to configure windows, then configuring the service pack, starting at 35% and finishing on 37% and then boots windows normally. This is very annoying to go through everytime I reboot. I ran the portable fix it program from microsoft to fix windows update problem but it I booted into safe mode to try uninstall the service pack to reinstall but now when it reboots it says preparing to configure windows, then failure to configure service pack, reverting changes. Now it does this every time.I've tried running windows updates to try to reinstall but it just seems to go on forever. I have also run the System update readiness tool from microsoft but it does the same as the windows updates, runs continuously
View 3 Replies
View Related
Nov 29, 2011
Every time I rebooted my laptop windows runs through preparing to configure windows, then configuring the service pack, starting at 35% and finishing on 37% and then boots windows normally. This is very annoying to go through everytime I reboot. I ran the portable fix it program from microsoft to fix windows update problem bI booted into safe mode to try uninstall the service pack to reinstall but now when it reboots it says preparing to configure windows, then failure to configure service pack, reverting changesNow it does this every time.I've tried running windows updates to try to reinstall but it just seems to go on forever. I have also run the System update readiness tool from microsoft but it does the same as the windows updates, runs continuously
View 7 Replies
View Related
Dec 1, 2009
I have an Acer Aspire one. It came with XP and I have it dual booting into Windows 7 which is working well which I installed from a USB Drive as this model doesnt have a CD Drive.
In the main boot screen it says "Earlier version of Windows" For XP and "Windows 7" for windows 7. All was working well until yesterday...
Now I can't boot into "Earlier version of Windows" i.e. XP. It gives me the C:\windows\system32\config\system is missing or corrupt message. I can boot into Windows 7 fine but all of my work stuff is on the XP platform (I know I can access the files from "7" but I need to get it operational again).
Any ideas? Can I do a repair from the USB Drive?..I've tried a couple of things to boot from the USB Drive but to no avail. And I can't find the BOOT.INI file from XP (I think it gets moved to Windows 7's hidden boot partition when I installed it. I cant seem to access that partition either).
View 9 Replies
View Related
Sep 22, 2012
Windows 7 64 turns off the monitor 1 signal after startup. At login, it powers off monitor 1 and powers on monitor 2. Windows 7 behaves as though dual display is working even though monitor 1 does not display. It's the same for single display, the monitor will not work on cable 1 except at startup.Both 'Extend these displays' in Windows Screen Resolution and 'Extend' in the Nvidia Control Panel is selected. And changing which one is primary does not turn on monitor 1. Nor does switching the position of display 1 in either (ex.left/right/top/bottom).GeForce 8400 GS; Dual Monitor Solution 59 pin (DMS-59) to 2 VGA adapter -tried two of these adapter cables.atest Driver: 306.23 - installed a clean reset install of the latest Nvidia driver released last week.Same Resolution: 2 of the 4 monitors I have tried have the exact same 'recommended' resolution (1280X 1024), both 60Hz, and even chose 16 bit color for both instead of 32 to reduce resources.
Linux worked: Dual display worked immediately when I tried it in Ubuntu 10. So, it's not the hardware. It works in Ubuntu 12 too but not properly -it won't transfer windows across displays. My Windows 7 64 is an upgrade from Vista 64. One person in another forum with the same problem resolved theirs by reinstalling Windows 7. But another got the same problem only after a fresh clean install of Windows 7 64 with the same GeForce 8400 GS and DMS-59 when it had previously worked in Vista. Dual Monitors - Only One Works at a Time
View 5 Replies
View Related
May 30, 2011
everytime I create a restore point on windows 7, it disappears upon a reboot.
View 6 Replies
View Related
Mar 10, 2012
I just purchased a new alienware desktop. The display does not turn on when the computer restarts. I have to hit the power button to shut down completely to get to the login screen. My power option Display settings are set to :turn off the display: NeverPut the computer to sleep: Neveronly because if the monitor goes to sleep, i cant wake it up unless i reboot.
View 4 Replies
View Related
Aug 16, 2011
I have a Dell XPS 15 (L502X) laptop withIntel Core i7-2630QM processor6 GB DDR3 RAM15.6" Full HD LED Screen2 GB NVIDIA GeForce GT540M with OptimusMy display was a little 'warm'. I mean that what should appear as white didn't appear white, instead it appeared creamy (i.e. according to RGB scheme, the red content in the display was more than what is required.)To fix this, I did thisRight Click Desktop > Personalize > Display > Calibrate Color and then adjusted the red and green bars to make the color settings proper. Now, the display is as I want it to be.The problem is that when the PC reboots or when an UAC window pops up, the settings are lost and again my display becomes 'warm'/creamy. I've tried going to Control Panel > Color Management and doing what this says:
View 5 Replies
View Related
Sep 13, 2009
When I run the Display Color Calibration to alter the gamma cos it is too bright for me, It resets after any reboot or shutdown is there any way to keep the adjusted setting after shutdown/reboot?
View 9 Replies
View Related
Dec 3, 2011
I have just performed a full system restore on my Dell XPS L501 with Windows 7, but now it won't boot up. I get a 'Bootmgr is missing' message. I think I might have to try re-installing Windows but did not receive a disk with the PC. Anything else I should try?
View 1 Replies
View Related
Jan 15, 2013
Graphics card: ATI Radeon HD4870 x2
Running on windows 7 x64 ultimate
I was browsing away and my whole pc froze, with a strange little box around my cursor, although the sound was still working, I force shut down it and restarted and little message popped up saying the display driver has stopped working, I tried multiple things to solve this, to no avail, eventually it kept happening and it got so bad the computer would not start, i tried all of the "F" keys on startup and none worked, eventually i took it to a shop who wiped everything clean and it worked again.
Around 2 months down the line low and behold the same problem happened again, I found a solution and installed a program called driver robot, I used it and installed many outdated drivers, this seemed to fix the problem. For about 6 months, now it has happened again, my computer has now shut down and goes into a constant restart loop, as it is doing this the screens that show up are littered with dots and lines of many colours, I just need workaround on this, preferably without loosing all of my files.
View 4 Replies
View Related
Feb 27, 2012
how can i set up dual monitor display on my imac running window 7 with parallels? I have no problem when I run mac but when I run window, dual display doesn't work. I heard AND radeon has some problem with window 7 display setting.
View 1 Replies
View Related
Apr 6, 2012
Recently, I got my pc cleaned from virus/malware, but now is in good/health shape. When I create system restore point, it's succeed, but every time I reboot or turn off computer, my restore point is missing.. and I'm newbie about computer. I'm using windows 7 home premium 64bit, I don't have installation disc because it come bundled with Gateway, what I have is only restore to factory setting DVD.
View 2 Replies
View Related
Nov 15, 2009
Dual Monitors reset when Screensaver/sleep/reboot/hibernate
&
Returning to single monitor cause a hissy fit tantrum by win 7
I have a problem with Windows 7 and my dual monitors setup. I have 2 SyncMaster 245T monitors, connected via DVI cable to a NVIDIA GeForce 7900 GTX card. I have downloaded the latest drivers from Nvidia for the card, but I am experiencing a fairly regular issue with regards to running Dual monitor setup.
When ever the system goes in to sleep/hivernation mode for more than a few minutes, upon restarting, the second monitor is no longer on. I have to physically go into settings and extend my monitor again. Simply rebooting the computer reboots it back up on only the one monitor. I have noticed twice now that this also has occurred when the computer went into screen saver mode too.
Additionally a freakish thing I found happens when I was trying to isolate the trigger of this problem is that, when I turn off the power to the 2 monitor (Not mains, just the switch on the second monitor. So mains power is still supplied) windows 7 has a major hissy fit.
It repeatedly sound the audio cue for disconnecting hardware, while the one monitor left on, constantly flickers, in what seams an attempt to return to one monitor. Only returning the monitor back on would stop the unsuccessfully attempt to return to the one monitor.
I have tried to look for anyone else with similar problems on the net, and apologize if a similar problem has already been posted here, but my search revealed nothing. I was wondering if anyone knew of a fix, or has had similar issue that they resolved.
View 3 Replies
View Related
Jan 6, 2010
I have a desktop running Windows 7 Ultimate and a laptop running XP Pro. Is there any way to use the laptop as a second monitor? I know how to set it up physically but just don't know if the laptop has to be running the same OS or not.
View 2 Replies
View Related
Mar 12, 2011
is there a way to have a screen saver only on my 2nd monitor as i have it set up as extended display dual monitors?
View 1 Replies
View Related
Oct 27, 2009
Just got a 2nd monitor and was wondering if there is a way to make XP mode utilize dual displays? I use xp mode to log into a citrix server for work and it would be great to have my citrix be in dual display.
View 3 Replies
View Related
Apr 5, 2009
Is there something built into Windows 7 that will do a screen saver of a library of photos, yet use *both* displays to show multiple photos? There are a couple in there, but they only seem to work on the primary display. Is there a way to enable multiple displays for these?
I have a nice 3rd party app I purchased in the XP days that does this, but was wondering if there was a way to get 7 to do it natively.
View 1 Replies
View Related
Jul 2, 2011
I have an external monitor, actually a TV connected via S-Video cable coming out of the back of my video card. My TV is my second desktop. All of that is fine. The problem comes in when I log off or "switch users" (there are no other user profiles on my computer - I only log off or switch user to make sure the kids can't get on without my permission - they don't know my logon code), the TV loses the picture and goes grainy, but when I log back in, the TV does not "kick in" again. The only way to get the TV to display the second desktop after logging out or switching users seems to be to restart the computer entirely. If it reboots, it picks up the TV as second monitor again.
If you simply log in again, it does not pick up the TV as second monitor. Is this related to some setting that says the TV should only be the second monitor on the admin's account and not for "all users" or something? It is annoying to always be restarting my computer to watch a video on my TV. By the way, in all cases, the "Display" settings in control panel show the TV as the second monitor. But looking at the actual TV, all you see is a grainy screen that obviously is not being fed any clear signal.
View 1 Replies
View Related
Aug 28, 2009
i'm running a vaio vgn nr21s/s (nvidia 8400MGT) with a samsung syncmaster 226bw ( 22') connected by a vga connector and i cant have my max resolution (1680/1050@60htz) in Windows 7 x64
i tried a dozens of drivers, the new and the old ones (laptopvideo2go, dox moddified...) for Windows 7 x64 and for vista x64... and still the same problem, still stuck at 1600/1024
i thought it could be the vga connector but im running xp pro 32bits too and theres no problem with that i can get the right resolution.
View 3 Replies
View Related
Jun 28, 2011
I had a hard disc crash, installed a new disk, upgraded to Windows 7 and now my dual monitors display the same image where before the crash they did not.
View 2 Replies
View Related
Oct 9, 2012
When I start my laptop, it shows the HP logo, begins to boot and is almost instantly interrupted by a white screen that scrolls down from the top. It reboots right after the white screen.I am able at the HP logo screen able to navigate to System Restore and that is where I run into my next problem.When the System Restore window opens for confirmation it shows that "Local Disk (C) (System)" status: "Ready to restore" and the check-box next to it is checked.The next line has a empty check-box for "Local Disk (C)" with the status: "The drive cannot be found." I can also successfully boot into Safe Mode with Networking. I can access all my files. Which leads me to believe that it is a hardware problem. Possibly the motherboard or graphics card.
View 7 Replies
View Related
Jan 29, 2010
I have been adjusting my DRAM timings in the BIOS and lose the ability to reboot onto Windows 7 64-bit. So, I power down and reboot and I get a black/blank screen and 2 beeps from the MB. So, I turn off my computer and I have to remove my Graphics card to access the OS again. Can anyone suggest an option or two that will help me restore to SLI mode?
View 8 Replies
View Related
Jul 11, 2009
I have an Nvidia 9600M GT on my laptop and driver 186.03
The problem is, there is no option in my Nvidia control panel to select whether I want the mouse to go to the external display via the left side of my screen or the right side. It always was on the right side, but suddenly its on the left.
Any ideas?
View 2 Replies
View Related
Aug 10, 2009
I have a dual head setup that works ok. My issue though is that whenever I do a reboot, I have to go into display resolution settings and re-enable "extend" displays.
Is there a way to make this persistent? It's just annoying doing a reboot and having to spend time re-organizing your desktop every time.
View 3 Replies
View Related
Dec 7, 2009
what inexpensive video card for dual display?
View 9 Replies
View Related
Mar 25, 2009
I've upgraded windows 7 from build 7000 to build 7057 (totall reinstall not just upgraded). My pc is connected to the TV (for movies and such), when the computer boots both displays work fine. After logon however I cannot get the second display to work. I can expand them all I want but, it simply won't work.
View 1 Replies
View Related
Aug 31, 2009
Sometimes as an end mobile computing user, we may be too demanding especially when hoping to have a huge screen for multiple windows and applications running simultaneously but at the same time, we don’t want it to be too bulky for convenience when carrying along. However, with existing solution, we can’t go too far except relying on external LCD panel for display extension which is not always available.
Here is how the new innovative solution from gScreen that able to fill up the gap. Dubbed as Spacebook, it is claimed to be the first laptop model featured with dual 15.4-inch that can be slide out for display extension when necessarily. Read The Rest Here : GScreen Dual Display Spacebook Targets to Increase Productivity for Travelers » My Digital Life.
View 4 Replies
View Related
Nov 21, 2009
im running win 7 x86 in a vaio vgn nr 21s/s with a 8400mgt and i cant find a driver which displays my correct resolution in my external wide screen (22'' at 1680/1050)
all i cant get is 1600/1200 or above but not he optimal.
View 5 Replies
View Related
May 31, 2010
My dual screen has suddenly stopped working on my laptop. Now when I hit 'detect' my laptop screen goes black and I have to force restart the machine and disconnect the second laptop. Is this likely to be a hardware fault?
View 2 Replies
View Related
Jul 3, 2012
Display or video driver for Pentium dual core, provide a link..... Because of it the clarity of video is not good and I can't set a screensaver.
View 5 Replies
View Related