External Hard Drive In Device Manager, But Not Able To Access It?
Jan 9, 2013can see my external hard drive in device manager, but not able to access it
View 4 Repliescan see my external hard drive in device manager, but not able to access it
View 4 RepliesI just bought a new ASUS computer with Windows 7. I have a Macbook Pro and would like to transfer my photos and music onto my new computer. I have 2 external hard drives that work perfectly fine on my mac as well as other PCs. When I plug either of my external hard drives in they are recognized in device manager and say they are working properly but are not recognized in disk manager or under my computer...
View 1 Replies View RelatedCan see my external hard drive in device manager but not in my computer
View 1 Replies View RelatedFirst I want to say that the drive works without problems at the correct speed. The problems come upon disconnect. I also want to to stress that USB 2.0 discs are working flawlessly. If I use safe eject and the look in the device manager I get an error 47 saying that it has been shut down but not disconnected, it also says I can rectify it by disconnecting and reconnecting but this does not work. If I do so the drive will not be recognized. The enclosure has a power switch. After a safe eject I have tried both pulling the USB cable while power is still on and also going the other way by first shutting the power down. In both cases the error 47 shows in device manager. When this happens the CPU load goes up to about 20% and stays that way when it before was around 0 at idle. If I reboot the drive reconnects and I have no problem with it unless I try to safely eject it again.
View 2 Replies View RelatedI've spent most of the night searching and cannot seem to find an answer to my problem.I have a NAS set up with two 2TB Samsung Spinpoint hard drives. The hard drives in the NAS were partitioned to have 300GB in a RAID 1 and the remainder in a RAID 0. One seemed to be failing so I removed it hoping I could connect it externally to my laptop and recover the data. When I hooked it up to the laptop, it seemed to connect fine but did not show in My Computer. When I went to Computer Management - Disk Management, it shows the partitions as healthy (see image - Disk 1). However, when I right click on the partitions to assign a drive letter, the only options available are Delete Volume and Help. Same when right clicking the Disk 1, all that is available is Convert to Dynamic Disk, Properties,
View 9 Replies View RelatedI was normally using my computer, when I suddenly noticed one of my hard drives disappeared from My Computer. Checked the Device Manager, I get the following. Trying to initialize it throws up this error: Seems to spin just fine. Trying different USB ports failed, switching cables as well. Already tried a few programs. GetDataBack for NTFS throws up error 1117. R-Studio also fails, as does DMDE and MTY. My friend even borrowed me Microsoft DaRT (part of MDOP), but when I boot into it, it doesn't recognize the HDD at all, no matter how hard I try. Only my Windows 7 installation does.Anything I can do in this situation? I had a lot of important data on it, and it's not completely dead yet. Maybe I can still save it somehow, without haivng to pay one of those data recovery thieves...
View 9 Replies View Relatedafter plugging in the external hard drive after a while I get you need to format the disk in F:\ do you want to format?After a while throws another warning saying F: is not accessible, Data error (cyclic redundancy check)It was working well until last week but then suddenly started giving this error message.
View 1 Replies View RelatedI have recently had to ditch my old computer windows xp, and bought a new Dell running windows Hoem repmium 7 (64 bit). I had a 32 bit ide external hard drive and had backed up my files there. Having got the enw copmpouetr set up I am trying to access my archived files on the 32 bit to transfer to new hard disk, but am unable to do so. Windows explorer locks up.
View 3 Replies View RelatedI have a Maxtor External Hard drive and Windows 7 Premium 64 bit. I have a user setup for each member of my family on the computer. The maxtor drive was working fine uptil I decided that I wanted only myself to be able to access it only. The drive appeared as my K drive. I went to sharing and added myself as read/write access and removed the everyone share thinking that only I would be able to use the drive. I restarted my PC and now nobody can access it. When I plug the drive into the usb slot the drive whirs up as normal but there is no drive letter for it and it does not appear in device manager etc. I plugged it into my old XP machine and that cannot read it either..
View 2 Replies View RelatedI have a LaCie external hard drive which works fine on other pc's running Windows 7 Ultimate, but on this one it is an "unknown device". I have tried it in different ports but with the same result. I've checked with Windows Compatability and the exact model is listed there as being compatible. I've been to the manufacturer's website but there are no drivers available.I have the same problem with any USB device I plug into any port. I have tried a complete Windows re-install from a different CD but it made no difference.The only USB devices that work are the keyboard and mouse.I have given the LaCie HD as an example because I am hoping that if I can get a specific device to work, I may be able to solve the problem with others.
View 5 Replies View RelatedThis morning while i was watching a movie from my Toshiba 500GB external hard drive, there was a windows update going. Because of the lagging due to the update and all, I restarted it after the update is done while my ext. HD is still connected to the computer.
After restarting, somehow I can't seem to access my ext. HD even though the HD is detected. The HD somehow became a "Local Disk K:" and everytime i try clicking it a pop-up telling me that "K is not accessible. The parameter is incorrect".
I googled the problem and found one solution that told me to run a CHKDSK on the command prompt. I ran a "chkdsk /r K:" but then got stuck on the "stage 3 of 5" where the chkdsk is verifying Usn journal. This has been going on for 5 hours and the cursors still blinking.
I can access my HD again? Does the verifying Usn journal really do take this long?
I am using Windows Seven ultimate x64 and I started having a problem when trying to access user's folder under documents and settings or users on any attached external hard drive on my computer. i didn't have this problem before, it started on the same installation of windows and without any changes to my system settings or user settings.
I am a computer tech and I use my computer to backup data before repairing computers so I attach the hard drive to my computer using a USB enclosure. This is limiting my work since I didn't find any solution yet. It's giving me the error below: "you don't currently have permission to access this folder" This is happening on any external hard drive I want to access the user's data.
i took out the hard drive from my laptop that had a BSOD and can't boot. I boutght an enclosure n plugged it using usb to another laptop so i can get my files, but when i click on the disk a window pops up saying disk is not formatted..i dont want to lose my files si i downloaded tesdisk. When i choose "Analyse" it seems that it finds four partitions, but above each one there's a warning "Incorrect number of heads/cylinders 255 (NFTS) ! =240 (HD) or Bad sector head and Bad Ending Head and Bad Starting head..I dont know what to do next.
View 1 Replies View RelatedI have a Titan 500 GB portable hard drive, the computer will after a longer than normal time recognize the PHD, the list of files will open up. But when I try to open the file, I get a non responsive message, then it just freezes.
View 2 Replies View RelatedI have a 3 Tera HDD. (WD My Book Essential (USB 3.0)). Last night I uninstalled a software which I do not remember its name by mistake. Apparently it was related to my WD hard drive for my computer does not recognize it anymore. I checked my device manager; "Base System Device" is not recognized. I ran windows troubleshooting. It says "Base System Device" Driver is not found. I searched a lot, but I couldn't find the driver. I also ran drive checker software.
It says:
Device name: JMB38X SD/MMC Host Controller
File name: MSI_GX633_Card For Windows 7.zip
Hardware ID: PCIVEN_197B&DEV_2382
I could not find this too. I also have another portable WD which is still recognized by my computer.
I have an Asus M2N-E SLI motherboard, a W.D. SATA WD300HLKS hard drive, and a SATA DVD R/RW.I'm trying to install Windows 7, BUT I can't get passed the... "To install device drivers to access the hard drive, insert media.................... ..... Press OK to continue. If I hook up a IDE drive it will find that. I've tried for hours to find a solution and/or drivers. Tried Asus, NiVidia, Western Digital,
View 9 Replies View RelatedDrive was fine in XP, new computer with 7, USB plug-in shows "USB Device Not Recognized?" The driver is up to date, per driver upgrade site?
View 8 Replies View Related.I didn't wait for the computer to tell me it was ok to remove the drive in the usb port. Now my computer no longer recognizes the external drive After removing my external hard drive (without the ok) my computer no longer recognizes the external hard drive. What do I do.
View 1 Replies View RelatedI have completely formatted my hard disk with seagate seatool. Then I have installed windows xp sp3. I have made 4 partitions at that time i.e. c,d,e,f. After that I have installed windows 7 now I can't see my hdd in disk management or in device manager. Both device manager & disk management are showing me my external drives like pen drive.
View 9 Replies View RelatedI have an internal hard disk not in use ,and I would like to make it as external disk !I looked on the net and I found I should have the " encelsure " butt I think I wont find it here in my city .So is there another way ? like usb -esata cable
View 3 Replies View RelatedMe and my brother built me a new computer from scratch (he did the building - i did the watching). I purchased an internal hard drive from Overclockers UK. It's a Samsung 1TB drive. I also have a 64 Solid-state drive in there as my primary hard drive that Windows was installed on and a couple of programs are installed on. My storage disk (the 1TB disk) is for all my music/films etc. Whenever I drag and drop a file into the Samsung hard-drive - it copies it rather than moves it instantly.When I had a laptop, I had 3 external hard drives and this is the way it copied files onto them.how I can get the internal drive to stop acting like an external drive?
View 6 Replies View Relatedunable to access external hard disk?
View 2 Replies View RelatedI have a USB external hard drive that I keep all my documents etc on (had it for years)I upgraded from Vista Home to & Home Premium then had to upgrade recently to Professional to run my Sage. Through all these upgrades my ext. drive ran fine. Occasionally the drvie letter would change if I had something else plugged into the USB, this was always easily corected in disk management by changing the drive path.The connection on the case packed up so I had to get the drive put into a new case, now when I plug it in the drive is assigned G instead of F, I tried to change the drive letter allocation in Disk Management but it won't let me as the program still thinks I have a second ext. hard drive which is labelled F. I suspect this has happened because when the usb connection broke the drive was disconnected suddenly instead of a proper eject.How do I get Disk Management to remove the inactive drive - i can't find any obvious way - eject, delete etc are all missing when I click on tools or tasks.
View 2 Replies View RelatedLow disk space, Can transfer data on D drive to an external hard drive
View 5 Replies View RelatedI can see my external hard drive in device manager, but not in my comp
View 3 Replies View RelatedMy external dvd/cd drive (Sony DRX S7OU W) previously worked from this computer running on Windows 7 but I now receive the message "Windows cannot access the specified device, path, or file. You may not have appropriate permissions to access them." The same dvd/cd drive continues to work on other computers. All other devices that I link to this port (camera, ipod) continue to function. I tried new firmware downloaded from Sony but this did not help.
View 2 Replies View Relatedmy SSD drive was suddenly inaccessible after a reboot, so I put my backup spindle drive into my laptop to get it started. Because I have important files I need to access from my ssd I put that into a case and plugged it into the USB port. Now windows explorer just hangs forever trying to detect/access it! in Computer management I cannot see the disk partition but I can see the harddisk device in device manager.
In windows explorer I can see one drive letter assigned (there should be two drives on the ssd) but when I tried to access the drive it just hangs forever. It also hangs with any other methods I try to access it (chkdsk, data recovery programs, Testdisk by CGSecurity)!!I think the main issue is that the external ssd is locking up everytime some program tries to access it... perhaps if I can somehow remove this lock I might be able to attempt a data recovery.
i tried to used pc disk clone x to clone my win7 to a smaller hard drive.now for some reason My Computer shows as 381 gig size instead of 682 gighere is a pic tried to make the partition a couple megs smaller to make it realize the actual size and its not working.
View 2 Replies View RelatedExternal hard drive salvaged from computer running Windows XPEncased, plugged into USB on new computer running (not by choice) Windows 7(Know where this is going?) Given every permission and ownership to new computer to have its way with docs on external drive. Can't copy docs from external drive to new computer even in (basicithout networking) safe mode. (And haven't tried a mac.)Can I somehow change permissions or ownership on the EXTERNAL drive to access my own documents? Anything else?If I throw it against the wall, will that work? Who is this other administrator to give access, when I'm the only administrator?
View 1 Replies View RelatedI just got an external hard drive yesterday, and have been asking a few questions on this forum. So far, people have managed to be very helpful with the previous questions, hopefully someone can do so here too.Reinstalling all my games to external hard drive, need to know if they will / how to make them appear / function properly in my GEF, whether added automatically or manually.I am basically going to have EVERYTHING put onto my 1TB external, and by everything I mean "Music, Pictures, Videos, Documents, Games, and maybe Programs". So, I made a folder for each of those things on it,and only now that I am reinstalling my games into the Programs one have I realized something.I am a bit obsessive about having a fully functioning Game Explorer Folder (GEF) with all my games visible in it. It's my assumption that when I install into an external hard drive, none of those games will be automatically added into the GEF. However, if I add them in manually (using the regedit method in the tutorial), should everything function properly, so long as I have my external hard drive on whenever I use the computer?I just need this to be confirmed before I start reinstalling more. Also, if not, please let me know if there IS a way to get them to show up in my GEF properly, or possibly move the GEF to the external hard drive or get it to recognize things from a different directory.
View 6 Replies View RelatedIn order to make upgrading via a clean install easier -- and because I've been considering one for awhile anyway -- I'm looking at picking up a decent external hard drives right now... and can't seem to find a clear answer to something:
Will I see any drop off in quality of playback or computer performance if I use a drive like this (external, USB) to store all of my recorded videos. The tuner and Media center would save everything directly to this drive and play everything directly from it. Would that cause any problems at all? I notice that it requires no power adapter since it's USB powered, and it has a Interface Transfer Rate of 480 Mbps -- not sure how either of these apply to my potential use of it.