My computer says that it does not reconized my usb cable. I'm trying to download a video from my camera and I hear the ding but I can't find the file. What do I need to do?
View 1 RepliesI have a Windows 7 enterprise 64 bit pc and an Onkyo receiver. I used to have them linked with an aux cable for music. But since I had enough of the bad sound quality I bought an optical cable and connected it. Now I have the problem that my subwoofer gives a lot of less sound then with the aux cable with the exact same settings and music. Also my pc recognises the optical cable as an HDMI cable and I don't think this is right. I can't change any settings either in the sound.
Pc Wizard told me I have this onboard sound card: ASRock SB600 High Definition Audio Controller Pine Technology HD48x0 audio
I just loaded a new copy of windows 7 home 64. Now my computer doesn't recognize my printer or Ethernet cable.
View 6 Replies View RelatedI have a new gaming computer with a high end video card and plenty of RAM and a high speed cable Internet connection. I also have a HDHomeRun TV cable unit which is listed to work with MS Media Center. When I set up my Media Center/TV connection it recognizes my HDHomeRun TV connection and all three TV channels via my MCard I got from Comcast cable. But next to the last dialog window, during setting up my TV connection, I got the following message, "Your computer is not digital cable ready. You will not be able to set it up for use with a cable card."
View 4 Replies View Relatedi HAVE TO GET THE INFORMATION ROM MY OLD COMPUTER TO A "CLEAN' USED COMPUTER. IT HAS BEEN SETUP FOR WINDOWS 7. bECAUSE OF MY WIFES SURGERIES AND THE UPCOMING ONE, WE HAVE TO DO IT OURSELVES. I HAVE A ETHERNET CABLE TO GO FRON COMPUTER TO COMPUTER, BUT THATS IT. I WAS HOPING TO PRINT OUT THE DIRECTIONS AND DO IT MYSELF.
View 5 Replies View Relatedand then after its been on a while it goes blank. and computer goes in sleep mode and i cant wake it up.. have to turn it off and back on
View 1 Replies View Relatedi have setuped all compute r wires but when i on the computer is telling that please checkvsingal cable
View 1 Replies View RelatedMy windows home server has decided to stop communicating with the client machines.The connector software won't connect (reinstalling makes no difference), remote desktop times out, manually shutting down (by pressing the power button) and restarting also fails to correct the problem.I can ping the server (average response time 3ms)The Home Server machine is headless and although there is a connector the only monitor I have doesn't fit the connector.I susoect that the internal battery may have gone flat and may be the servers clock is out of sync with the client machine (but even when the server is asleep its still connected to the mains).
Someone has said that I can connect a laptop to the sever via an ethernet cable but the only instructions I can find say that I have to set the IP address on both machines to be the same - Is this correct or is there another way of connecting?
I have a digital SLR camera, the Sony A200 and when I connect it to the computer running Windows 7 premium I get no response from the computer.The camera should automatically appear on screen with prompts to import pictures or view them.
View 7 Replies View Relatedhow to connect a projector to a computer using a vga cable
View 1 Replies View Relatedhow to connect a projector to a computer using a vga cable
View 1 Replies View RelatedI have aspire 7745 laptop running windows 7 premium 64bit. I had the video & sound working on the TV via the HDMI cable but it stoped working. Now the TV "sees" the HDMI signal (and receives a low tone) & the computer "sees" the TV as a secondary display in the device manager. but no signal or sound. i have tried many ideas found here and other places on line but no change.
View 1 Replies View RelatedCan I plug-in (and -out) a SATA cable (to hard disc) from (ASUS) motherboard slot when computer is running?
Or will this cause a damage to hardware?
I have a HP Pavilion DV4-1030en. Specifications:
Intel Centrio 2 2,00GHz
4GB ram
nVidia 9200m GS
So, these are giving the main performance to my machine. I have also a nice Samsung D5000 TV (32" ) FullHD. When I connect my Laptop with a TV, computer start lag. It even doesn't use all of CPU (20-25%, while playing 720p video in TV with 10 fps (Fraps)). I've all latest drivers and everything should work. Using Windows 7.
plugging my vga cable from my computer to tv but signal drops
View 2 Replies View RelatedI have an HP Pavilion Elite HPE machine, Windows 7, Radeon HD 5700 Series graphics card, connected to an Acer monitor and HDTV. Here's details on my setup:
My Equipment | Building a Home Theater With Your Office PC
My problem is that even though my HDMI cable's plugged into my Radeon graphics card, sometimes the PC only recognizes the Acer monitor and not the receiver (that's connected to the HDMI cable and my HDTV). So I end up having to plug and unplug the HDMI cable several times (sometimes 10+) before it recognizes the HDTV/receiver connection. Is there any setting that would favor the card/PC recognizing the HDMI cable more frequently? I've heard it's a handshake issue, and that maybe using a different type of cable would work. But wondering if there's a setting I could use before switching out cables.
I have an Acer Aspire laptop running Windows 7 Home Premium x64.
I regularly connect it to my TV monitor via HDMI cable and fall asleep watching movies (played on VLC or Windows Media Player). I set the computer to go to sleep after 1 hour.
Multimedia Settings are set to "Allow computer to sleep" under "When Sharing Media" in the Power Management section.
Screensaver is disabled. I have overrided my audio driver, since powercfg command suggested it may be a conflict.
If I am playing a movie without the HDMI cable plugged in, the computer goes into sleep mode right on schedule. It is only when I have the HDMI cable plugged into my TV monitor, that it refuses to enter sleep mode.
I just installed a new copy of win 7. My computer doesn't recognize my printer or ethernet cable. What drivers do I need? Any special order?
View 6 Replies View RelatedHere are the computer specs of the computer:
Ultimate SP1 64-bit
Xion 600W PSU XON-600F14R-201
Asus M2N32-SLI Deluxe Motheroboard
nVIDIA nForce 590 SLI Chipset
BIOS Revision 1402
NVIDIA GeForce 8800 GTS 640MB
AMD Athlon 64 X2 Dual Core 6000+ 3.15 (15 x 210 FSB)
Muskin 4GB (2 x 2GB) 991587 DDR2-800 SDRAM 5-4-4-12
Koolance EXOS2 Watercooled
OS Drive: Seagate Barracuda ST3500820AS 500GB
DATA Drive: Samsung HD501LJ
NVIDIA nForce 10/100/1000 Mpbs Ethernet
Realtek RTL8187 Wireless 802.11b/g 54Mpbs USB 2.0 Network Adapter
The CAT 5 Ethernet cable network cable is attached to our main Linksys WRT320N DD-WRT router ---> Motorola SB5101U DOCSIS 2.0 Cable Modem ---> Coaxial cable from wall outlet. Another computer is also directly connected to the same router via CAT 5 Ethernet cable and two more computers are wirelessly connected to the same router and none of these three PCs are experiencing issues so this should rule out the router as the culprit.if I leave the computer on (even for hours) with no network cable attached to the computer, it does not turn off. But as soon as I plug in the network cable, the PC will shut itself off within 5-15min.Based on the same scenario as described above, here are the troubleshooting attempts I made without success, except for numbers 4 and 6:
1. Switched to different network cable and router port.
2. Disabled Network Adapter connections in "Network adapter settings" for both the onboard ethernet port and wireless adapter.
3. Ran MSCONFIG.EXE and rebooted in diagnostic mode. Only basic Windows services are loaded. No startup programs are loaded.
4. Rebooted in Safe Mode with networking but could not establish any network LAN/WAN connection. Computer did not shut off!
5. Cloned entire hard disk to another hard disk and switched SATA data and power cables on the same computer.
6. Installed fresh Windows on different hard drive on the same computer. Computer did not shut off!
Out of those 6, only numbers 4 and 6 were where the computer remained on and didn't shut off at all after the network cable cable was plugged in.
Can I plug-in (and -out) a SATA cable (to hard disc) from (ASUS) motherboard slot when computer is running?
Or will this cause a damage to hardware?
I have Windows 7 Pro (RTM) installed on a DELL Precision M65 laptop.
My LAN interface reports "Cable unplugged" although the cable is inserted and working.
I have no network connection through this interface.
the onboard NIC is a Broadcom NetXtreme 57xx Gigabit adapter and the driver reports it is working correctly.
If i try to install the latest driver from Broadcom, Windows says I already have the latest driver installed!
Any Suggestions?
*My SD card is not recognized by my computer*We were out for 2 weeks water-skiing with my new SonyAction cam (basically a GoPro by sony). I used the SD card from the camera at the end of a day to view the files on my laptop but didn't copy them over as the card still had 14GB of free space. (16GB Card)The next day I put the card into my laptop again and one of the files was corrupted , so I copied over all the files and formatted the SD card for re use the following day(Have done before card worked fine).Now we are back and I cannot access any files on it, both on my laptop or PC!! These videos mean a lot to me, so If anyone has any idea how to get this working or a place I can take it to recover data?When I put my SD card reader into my PC without the SD card in it, (Its a USB with an SD card slot on it) the safely remove hardware appears in the system tray and plays the sound that It recognizes a connected device. The SD card is not recognized at all when I connect it to the USB reader.
- This card was working in the camera.
- I believe the card broke somehow when I plugged it into my laptop, but I didn't want to think those thoughts just yet
<img id="ums_img_tooltip" class="UMSRatingIcon">
My I pod was showing connected but the computer showed no connection and all sync greyed out. windows 7.
View 1 Replies View Relatedsince last week ive been having a adobe flashplayer problem . I need to do you tube videos but now I cant get any videos everytime i try and get a video it tells me i must have adobe flashplayer 9 or better installed on my computer !!! Ive downloaded flashplayer 11.3 like 40 times and it still does not work . Its like flash-player is not recognized on my computer no more even though it is downloaded and installed.
View 14 Replies View RelatedI have attached a Seagate 500 GG external hard drive to my computer but it is not showing up in My Computer.I have browsed similar threads and on their advice gone into Device Manager.The drive is there but with no letter assigned to it but when I right click to assign one, it refers me to Windows Help, which is unable to solve the problem. There are actually two extra ikons in Device Manager - one marked FAT Healthy (EISA Configuration) and the other just marked (GPT Protective Partition).The device is acknowledged as working properly in Device Manager.The files on this drive were created on a Mac, which may be the source of the problem? Most of them I will therefore not be able to read, but there is one which is a .mov file which I should be able to read and hopefully copy - if I can access it.Is there any way I can access the drive via my PC (Windows XP) or will the drive have been formatted for Mac only and therefore is inaccessible via PC?
View 3 Replies View RelatedSo each time I start up my computer, my mouse, keyboard, and headphones getrecognized. My mouse is the only device of those 3 to use usb. My blue snowball microphone and my hawking directional antenna don't get recognized until I unplug them and plug them back in. It take 2-4 times of unplugging and plugging in for it to recognize my snowball.
View 2 Replies View RelatedI have a Zotac 570 gtx connected via HDMI cable to my Asus VE258 LED monitor.I've had this video card and monitor setup working before with the exact cable, card and monitor.Something changed in my system where the monitor is no longer recognized for what it is. When i go into my Nvidia control panel under change resolution 1.Digital Display, 2. DVI-PC Display - Resolution 1080p 59 Hz. There is no DVI cable plugged into the computer and the monitor is set on HDMI input. When i go to my Audio playback devices, the HDMI connection does not show up at all, even as disabled or disconnected.When i go to play a game (Diablo 3, Skyrim, Farcry2) The game either doesn't open (skyrim) giving me the error that resolution is not recognized (but then does not give me any resolutions to choose from in the options menu) or will play (Diablo 3) but is stuck on extremely low resolutions with only 2 options.
Here's what i've done. Contacted Zotac and had them send me the most recent drivers for the video card. Uninstalled originals and re-installed the new ones. Contacted Asus (they say its not the monitor as long as its set on HDMI input) I am unable to find a driver that will make my computer (Windows 7) recognize the monitor for what it is. Zotac failed after their attempt with the driver and told me to RMA the card. So i did... i waited a month.
So I've been getting these annoying BSOD's only after I'm off WiFi and when I'm using my LAN Cat.5e cable..
Technical Info:
STOP: 0x000000D1
nvm62x64.sys
Windows 7 . . .
- x64
- full retail version
- age is about 2 yrs
- age of OS is also about 2 yrs
i just installed PC Lin-Q (USB 2 High Speed Bridge Cable) between tow of my Desktop Computers #1 Windows 7 RC1 and #2 Windows XP Pro SP3, installed to Windows 7 RC1 as Windows XP SP3 compat and it works fine !
View 8 Replies View Relatedi have a USB KKL 409.1 VAG COM VW AUDI Seat OBD2 Interface Cable to see the cars electronics and faultcodes, but y cant get it installed, windows says the drivers are already instald.anyone have a idea what to do?
View 1 Replies View RelatedAll PSU SATA power cables I've seen have only four connectors on each cable. Assuming the rail can handle the load and the wire used is large enough to avoid a voltage drop, is there any reason why there can't be more than four HDDs on a cable?
What I am wanting to do is run an SSD (boot/program) and six data drives (probably 2 TB WD Greens) on a single cable that I can make up (the PSU is a modular Corsair HX750; a bit oversized but that will cut down on heat and, hopefully, increase the life of the PSU) to cut down on cable clutter (the case I want to use is a bit tight; space to put it is a problem so it needs to be small). The original cables are made with 18 AWG wire. By using #14 AWG wire, the calculated voltage drop at the last HDD in the string (the SDD would be first) will actually be less than on the Corsair cable. The computer would read or write to no more than two of the HDDs (and the SDD) at any one time. There will also be two hot swap bays (3.5" and 2.5") in the computer (for making back ups) as well as an optical drive but each one of those three will get their own cable.