I have install xp on raid striped but when i try to install win 7 the driver i have are not the correct ones i have a dfi lanparty tu p45 t3rs mb and two wd 500gb hdd. i have looked around but cant find any others anything i can do or anone know where i can get driver
View 2 Replies
I have W7 installed, works fine. I bought 2 HDDs and wanna add them just as data disk and set up as RAID1. If I set up RAID in bios, Windows crashes when loading with classic blue screen + restart. Is there any way to make it work (install some driver etc.) or do I have to reinstall Windows with RAID set up prior to Windows installation? I have Asus P7P55D-E board.
View 1 Replies View RelatedMy PC is currently using a single RAID 0 drive that contains my Windows install and all my data in a single partition C: (I'm well backed up so happy with the risk of RAID0)
The RAID0 drive is setup by my motherboard controller so Windows just sees the one drive.
I am thinking of adding an separate drive for windows, hopefully an SSD. I would like to do a fresh install of Windows 7 on the new disk then rename the old RAID0 drive to something different such as D: . Then reorganise it into just a data disk.
My question is.. will the new Windows 7 installation just see the old RAID0 disk as another disk? I know this would work witha normal disk, but does RAID0 transfer over to a new installation ok?
I would like to get 2 SSDs and put them into a raid array using Windows 7-64bit, but wanted to make sure I understand how to do that. The 2 SSDs will be the only drives in the system. My computer has an X58 motherboard with an ICH10R. Here is what I think is the correct procedure: Boot into the bios. Set the storage config to RAID (the other choices are IDE and AHCI) Reboot and hit Cntrl-I to get into raid menu during boot. Set up the raid array in the setup screen. Reboot to the Windows 7 install CD and install Windows Is this correct? Are there any other steps I need or tips I should be aware of?
View 9 Replies View RelatedI'm trying to do a fresh install of windows 7 and it wont recognize my hard drives. I've done some research and determined i need the correct drivers, but i don't know which ones. I'm trying to install them on 3 WD3000HLFS in RAID 0. The HDD are plugged into SATA 6 ports( only 2 SATA 3 ports on the mobo).
View 4 Replies View RelatedI have been trying to get windows 7 Ultimate 64 bit installed onto a raid I created with two ocz agility 3 ssds. Everytime I try loading the drivers at install it gives me an error stating the drivers are unsigned and to install a 32 bit OS. When installing a 32 but OS, the install works normal and the computer runs fine. I am just wondering why it wont install for 64 bit considering I would much rather run 64 bit. I went to both the MoBo's website and the main companys website for the chipset drivers (AMD) but have both turned up with the same error.
MoBo = Biostar TA75M
CPU = A6-3650
2x OCZ Agility 3 60gb SSDs (2.22 firmware)
I have 3 driver onmy compute. which worked as 1 when playing games ex. got a virus o the shop cleanedor me.Btwo driver wrks at a time. And i need all 3working to play games. pc worldused to do it bu not ay more.
View 1 Replies View RelatedI am having trouble installing windows 7 (home premium) on my new raid array (2x intel 330 120GB SSD in RAID0). Basically, windows CAN see the raid volume. it recognies that there is a single 223 GB volume available. I select "Load Driver" for the volume, and plug in my trusty USB with the appropriate intel SATA RAID drivers. Win7 recognizes that there is a compatible driver on the USB, installs it, but still says: "Windows cannot be installed to this disk. This computers hardware may not support booting to this disk. Ensure that the disk's controller is enabled in the computer's BIOS menu". The format and create new partition options are grayed out for this volume.
Using the Intel Rapid Storage Technology tool, I combined the two drives into a raid0 volume. This is confirmed because when I restart, the raid volume shows up in the RST echo with the right size, and also indicates that the volume is bootable. It is also confirmed because the windows 7 setup only sees one 223GB disk. I have confirmed that in the BIOS, the SATA controller is set to RAID mode (not AHCI). I have confirmed that in the BIOS, the first boot option is "RAID intel SSD". I've tried the RAID drivers that came with the motherboard, Ive also tried the raid drivers available from intel and the latest raid drivers available from the motherboard MFR.
ASROCK extreme 6
Intel Core i7-3770k
16 GB RAM
2x intel 330 120GB SSD
NVIDIA GTX 680
As part of the chipset driver installation, it also installed the RAID and SATA drivers that Nvidia provides.I have a 300GB HDD on the primary IDE channel although I currently boot from one of my SATA hdd's.How would I go about transferring my OS to a RAID 0?Would it be possible to just system image my current OS onto the IDE drive and then format my two SATA hdd's, enable RAID in BIOS and then use Seagate Disc Wizard to install the system image onto the RAID 0?Is seagate disc wizard capable of transferring to a RAID drive??Have the RAID drivers definitely been installed with the Chipset drivers and will Windows recognise the RAID array?Have heard that you have to set up a boot partition the same size as the image on the RAID 0, would it then be possible to expand that to use the entire RAID partition
View 4 Replies View RelatedI recently purchased a 64GB Crucial M4 SSD and I'm trying to install Windows 7 with the Raid controller on a fresh HDD to meet the requirements for Intel's SRT. I'm trying to install Windows from a Mesh OEM disk but when it gets to the installation completion window an error pops up saying ''Windows setup could not configure windows on this computers hardware''.Windows installs fine under IDE/AHCI controller but that doesn't help me!
View 2 Replies View RelatedRecently completed my first computer build and am trying to install windows with a raid 0 on 2 500g HDD. I have it set up in the BIOS for 1-4 and 5-6 sata ports to RAID. When I boot from the dvd drive with the windows disk, after clicking install windows, it says: "a required cd/dvd drive device driver is missing" I figured this was a driver for the raid but i cant find it anywhere. if i select browse, there is a boot (x folder but i dont see anything in there that would help me. Do i need to download a driver to a usb stick and pull it off there? adn if yes where could i get the driver? i cant find it on the asus website.
here is my setup:
asus m5a97 LE R2.0 mobo
XFX Radeon 7870
AMD 8350 Processor
[code]...
So then I thought, that maybe I can't install the RAID drivers from within the OS. So I caused the BSOD on purpose once again, and then with ICH10R RAID activated and Samsung hard disks attached, I choose the Windows 7 Recovery mode in the boot menu. It sees some problem(s), tries to repair, does not succeed and does not ask for drivers (which I put on a USB stick) to install. I also tried to use the command-line in the recovery: "rundll32 syssetup, SetupInfObjectInstallAction DefaultInstall 128 iaStor.inf" but it gave "Installation failed."
So I'm clueless how should I proceed. Do I really need to re-install Windows 7 and load RAID drivers in the Win7 setup? I don't want to install any OS on the RAID, the Windows 7 is and will be on the SSD. I just want to have a RAID-1 backup using those two hard disks.
Installed a new M4 ssd today and loaded windows on it. Previously i was using 2 raptors in raid 0 for the os and programs. I re raided the 2 raptors and connected them to the jmicron ports and set them up for raid in bios, then created the raid 0 array no prob. Windows doesnt see the array when loaded up and i have the latest rst drivers installed..did this prior to the os install on the ssd. using the x58 e760a1 mobo. under device manager, the raid controller has an exclamation mark and no driver installed yet i have the latest rst 10.8.0.1003 installed..
View 1 Replies View RelatedI recently sold a pair of drives which i had installed Windows 7 onto.The drives were configured as AHCI in the bios.The buyer has come back to me witht he following message: i received the hard drives today. i can install windowsd 7 in the 2 drives. whats wrong? i try in raid mode and non raid mode and nothing.says that i can install files in this discs. what operating system was there befShort of them being damaged in transit I cannot see any reason why they would not allow Windows 7 to install on themAm I missing something? I have asked him to supply details of his motherboard. Are there any other questions I should ask?
View 5 Replies View RelatedIve been trying for 3 days now to install a clean os on a raid 0 setup. I can get the array setup in the bios np, but when it comes time to actually install the os i can't. Reason being i cannot for the life of me find a raid driver that is signed by windows>< The south chip is sb700.
View 6 Replies View RelatedI have the following MOBO:
ASUS P7P55D-E EVO
2X80gb Western Digital SATA Drives
2x2TB Samsung Spintpoint SATA Drives
I have already been using the machine with another 80Gb Western Digital SATA Drive with Windows 7 Pro 64Bit installed and now want to convert to RAID 5 for redunancy in case of Drive failure (We all say we will back up but we are all lazy when it comes to it LOL).I have taken out the original OS drive and plugged it into the E-SATA connector on the MOBO, gone into the BIOS, turned on RAID for the SATA Ports on the MOBO, and connected the 2 X 80Gb Boot drives. Entered the Hardware RAID Controller POST, and created the RAID 5 Volume from the 2 X 80Gb Discs.Now boot with Acronis Wester Digital edition.Clone the Original 80Gb Disc to the new Raid Array.Shut machine off, remove original OS 80gb Disc from E-SATA port.Boot machine.It starts to boot, and gets as far as the Windwos 7 Microsoft 4 Colour logo and then I get an error and then have to boot into Windows 7 from DVD and go through the repair process.When the Repair has run it reports the following:
The following startup option will be repaired:
Name: Windows Boot Manager
Identifier: {9DEA862C-5CDD-4E70-ACC1-F32B344D4795}
The following startup options will be added:
Name: Windows Recovery Environment (recovered)
Path: Recoverye52d0bc2-1f15-11df-af10-d764fe3715b8Winre.wim
Windows Device: Partition=D76190 MB)
A copy of the current boot configuration data will be saved as:C:BootBCD.Backup.0001 However it fails to do the update How do I get this RAID to boot successfully? I *don't* want to have to re-install the Operating System as that is just too painful a thought?
I have seen this question being asked a few times already. I just bought 2xSamsung Spinpoint F3 1TB drives and I created a dynamic striped partition with MBR in comuter management. If I try to install win 7, after dvd boot-up, will I be able to select the partition and install windows on it ? I know all about the advantages and disadvantages of using software raid 0. But, my question is simple. Can you just install an O/S on that type of partition (will it be detectable?) or do I have to buy a "fake raid" controller or boot some type of application first to make it detectable everytime I boot up my computer?
View 2 Replies View RelatedSo I just recently decided to do a RAID 0 configuration on my ASUS M4A89GTD with two 1 tb drives. I first set the Raid controller to the raid 0 setting and added my two drives. The raid manager reported back the raid 0 drive was healthy and working fine.
I proceeded to go through with a fresh windows 7, 64-bit install. The install goes fine but when the computer boots up to load windows 7, it hits a blue screen and instantly restarts. Over and over again.
I think I tracked down the issue to a rogue registry entry. Apparently there is an entry called iaStorV that causes the drivers.sys file to not load the drivers correctly, causing a blue screen error.
Things ive tried: Using ubuntu off a cd. Didn't work because the chntpw doesn't know how to mount a raid 0 drive Regedit bootloading programs, dont work because they dont know how to deal with a raid drive Regedit in the system restore command prompt. Doesn't work because it's version doesn't match windows 7
I have just bought two brand new WD 500 GB RE4 HDD's and connected them coorectly for RAID 1. I have changed the BIOS and Pressed Ctrl+F to create the RAID and this has been successful. When installing Windows you obviously get to the aprt where you need to load the floppy drivers to locate the drives...
I have downloaded ever driver from the Gigabyte support drive and loaded them onto a USB, not one driver can be seen when the USB is "Browsed" too...
How important is it that the drivers are on a floppy, as I do not have a floppy drive or access to a floppy and drives. Also what driver should be downloading as I tried the 3.2.1540.17 one and that was not seen, so I just downloaded them all in an attempt for success.
I have an ASUS Motherboard M4A87TD EVO, got two new hard drives, and changed the BIOS settings to a RAID configuration. After exiting BIOS, I loaded the WIN 7 (64 bit) installation disc, got thru the first few prompts of installation, and the pop up error menu shows up. "No signed Driver Found, Please insert CD/DVD/ Floppy", and my RAID configuration does not appear in the box as a hard drive for Windows to be installed into.
After researching on the web and contacting ASUS, I still don't understand. From what I can gather, it is a driver that will make THE INSTALLATION PROCESS RECOGNIZE MY RAID configuration. Apparently, it must be downloaded onto a thumbdrive and installed "during" the Windows installation. Is it specific to this type of installation, or manufacturer specific? Asus or Windows? A third party??
I have tried to find the way to do this, but without success as I cannot see the wood for the trees.
I have a mature Windows 7 system, with so many applications loaded that rebuilding from scratch is just not an option. I have a 300MB Velociraptor wholly given over to the OS and another empty 300MB VR. I want to extend, that may not be the right word, my OS to use both disks in Raid 0.
I've read several forum threads on this, but am still having trouble. I have win 7 32bit RC up and running for a long time on a 500 gig WD. Bought two 1Ts for a raid 0. I have the RAID chosen correctly in the BIOS, and the utility works fine. At the clean install for either 64 or 32 bit, I try to choose the drivers which I have downloaded from Intel and Asus, and tried to use the Vista drivers off my P5Q install disk, and still, Win 7 does not recognize the drive.
I have been home building and using computers for the past 25 years and I guess technology has gotten way over my hobbiest head. I have tried the USB flash drive route and I doesn't work either. Please, I know of the F8 workaround for unsigned drivers, but that doesn't work either. So, how are people raiding Win 7 at clean install?
Second question, is there a good tutorial at technet.com (which I can't find there) or someother place that tells step by step how to raid under disk manager in win 7?
I want to slick my drive and do a clean install of the RC version. I currently have a Raid 0 configuration on 2 additional drives (not the OS drive) using the Asus P6T on-board controller. Will that Raid be preserved and thus the data as well? What is the best way to accomplish this with the least amount of angst?
View 4 Replies View RelatedCan you setup a riad 0 after win 7 is installed, I have 2 1tb drives, win 7 on one other not setup yet.
View 9 Replies View RelatedI want to set up a raid 0 during the install for my c partition on Win 7 can this be done? If not what I will do is install on a parition on one drive and then after I have installed set up some stripped partition and hack the registery and change the locations of the Windows folder to be on the stripped partitions after copying them of course. This is just not a very nice way of doing it. My mobo doesn't support hardware raid so that is why I am trying to implement software raid and I have a second hardrive.
View 9 Replies View RelatedMy first post here, and I was just wondering if there was a way to integrate raid drivers in my windows 7 installation CD?
View 9 Replies View RelatedMOBO = Gigabyte x58a-ud5 I just got 2 SSDs I'm trying to put in RAID0 and hopefully clone my current install. When I change the bios settings to set the intel RAID controlled to xhd and raid but try to boot from my windows installation it wont boot, it gets to ''starting windows'' and then BSOD. When I turn the RAID setup off and try to install the XHD drivers the install aborts saying ''this is not a RAID setup". Is there something I can do to get the drivers installed on my current setup then clone it to the RAID drives?
View 1 Replies View RelatedI got this problem and cannot solve it myself for over a month, ANY advice will be appreciated! The goal is Windows 7 64bit with RAID0.
1. Windows XP 32bit installs fine on RAID0 (with proper driver integrated)
2. Windows 7 64bit and Vista 64bit installs fine on single drive.
3. Windows 7 64bit and Vista 64bit on RAID0 give BSOD 0x000000F4 during completing installation stage, then Matrix Storage manager shows RAID0 ERROR OCCURRED.
EDIT:
4. Windows Vista 32bit won't install on raid setup too. Its not the case with 64bits
I tried everything I could think of:
1. exchanged both hard drives
2. tested RAM
3. tried install with minimum pheripherals and 1GB RAM
4. messed up with BIOS, even updated to latest beta bios
5. tried installing intel vista64 raid drivers, tho windows 7 has itself
6. RMA'd my DVD Drive
and still NO GO
E7200 || Abit IP35 Dark Rider || A-Data 4GB || 4850 || X-Fi Gamer || Samsung F1 RAID0 || Pioneer DVR-212 || Corsair VX450 || HP w2207h
i want to change my existing install too raid0 i currently have install/programs on one 1tb drive and media/games on another 1tb drive, i have a spare 2tb drive unusedwhat are your suggestions so i reduce the amount of lost programs etc
View 4 Replies View RelatedI have Win 7 Pro 64 bit installed on an ASUS P7P55D LE motherboard which supports RAID 0,1,5 and 10 using Intel Matrix Storage Technology through an on board Intel P55 chip set. The system was assembled in Nov 2009 using two Western Digital Caviar Black 750Gb drives in RAID 1 as Drive C:. (I now know from Western Digital Customer Service that I shouldnt have done that, but lets move on from there). Last December, an error message informed me the RAID array was broken and identified one of the 750 Mb drives as needing replacement. I happened to have a spare 1.5Tb WD Caviar Black at the time, so I pulled the 750Mb drive and replaced it with the 1.5Tb drive. Life was once again good. Then on July 4th (wouldnt you know) there was a repeat of the December 2011 error message telling me to replace the other original 750Gb drive. Okay so I had another 1.5Tb WD Caviar Black laying around (dont ask) and did a similar swap out. Thats when I emailed WD Customer Support asking about the 750 since their diagnostic software said the drives were fine. Thats when I learned that I should be paying lots more for enterprise quality drives if I want/need RAID. Well thats not what ASUS says in their advertising, but live and learn. All thats prologue, because my real question is whether its possible to break the hardware-based RAID 1 array and set up a Windows 7-based RAID 1 with the two 1.5Tb WD Caviar Black drives without having to reinstall Windows 7.
View 1 Replies View RelatedBiggest bottleneck in my system right now is my boot drive, which is a WD velociraptor. I want to change this for dual 120GB SSD's in Raid 0 configuration. Can anyone walk me through the steps to copy over the existing Win7 64 install onto the SSD's, I dont want to have to load everything again
View 3 Replies View Related
