Windows 7 Wont Install Onto A Pair Of Raid Drives?
Sep 15, 2010
I recently sold a pair of drives which i had installed Windows 7 onto.The drives were configured as AHCI in the bios.The buyer has come back to me witht he following message: i received the hard drives today. i can install windowsd 7 in the 2 drives. whats wrong? i try in raid mode and non raid mode and nothing.says that i can install files in this discs. what operating system was there befShort of them being damaged in transit I cannot see any reason why they would not allow Windows 7 to install on themAm I missing something? I have asked him to supply details of his motherboard. Are there any other questions I should ask?
View 5 Replies
ADVERTISEMENT
Oct 23, 2012
I recently upgraded to an SSD. I moved windows 7 over to the new SSD and re-aligned the partition properly The drive setup is as follows:
2x 500GB WD Black drives in RAID 0
1x 120GB ADATA S510 SSD
In BIOS, RAID mode is enabled. You cannot enable RAID for one pair of drives and AHCI separately. I was assuming disks that are not part of the logical RAID volumes would be set to AHCI automatically. I have enabled NCQ in AMD RaidExpert for the SSD.WEI is 5.9 for the primary disk. The primary disk is the SSD.Other strange behanivour is that the RAID array and the SSD both appear as SCSI devices in device manager, and Windows won't accept the ahci drivers from ECS.
View 3 Replies
View Related
Aug 24, 2012
I need a PCI SATA 6 RAID card that has at least 4 slots for 4 X 2TB Hard drives for a RAID 5
View 3 Replies
View Related
Jan 23, 2011
I have bought a Bluetooth keyboard for my PC (running a Windows 7 64bit OS) and while I am able to successfully install and pair the device, I find that each time I either switch off the device (or PC) and switch either back on again I cannot re-establish the connection unless I remove the device and re-install and pair it once more? Surely it isn't necessary to have to follow this procedure every time I wish to use it...or is it?
View 2 Replies
View Related
Nov 11, 2011
I'm trying to stripe two drives using the disk management tool. Both partitions give me the option to stripe them but when I use the wizard the other drive doesn't show up to allow me to raid to it! Both drives have partitions on them at the moment, but I was under the impression that this will make a raid partition rather than a drive.
View 3 Replies
View Related
Mar 26, 2011
I have two 1.5TB WD HDs that I am going to use soley for storage, these will not be for the OS drive. If I place them in a Windows 7 Software RAID 1 configuration, and say my main OS drive was to fail. I would have to rebuild my OS drive on a new HD. Now when I do this, will the new install of Windows 7 I do at the time pick up my previous Windows 7 Software RAID 1 for my storage drives or do I lose the array? I am scared that if I lost my OS drive, my R1 storage array would go as well if Windows 7 keeps some kind of settings or configuraiton to manage the array.
View 1 Replies
View Related
May 9, 2012
in my PC there are some drives with RAID0 arrays and from little time I have bought a SSD for Operative System (Windows 7).in your opinion (on the BIOS) is it better making the Boot with SSD or with another drive with RAID0?
View 9 Replies
View Related
Feb 21, 2013
I've been having some issues with a computer that belongs to CEO of the company I work for. It was built by his son in law and that son in law doesn't really have time to work on it anymore so fortunately "end of sarcasm" that responsibility falls on me.Computer was running great until about two or three months ago where after shutting it down for the night and turning it back on in the morning would cause the computer to reboot three times after going through POST and during 4th time he was able to boot into OS (WIN7 64bit). I updated his bios and that seemed to fix the problem, BUT the computer was set in a Raid 1, but for some reason it is no longer set up that way. I see both HDD as separate HDD in "My Computer" C: & D:, both are 600GB with about 400GB of space free. How can I return them into their raid 1 configuration? MOBO is GA-X58A-UD7 Rev 2, Intel Core i7 970 cpu with 12GB DDR3 RAM Total. He has about $10,000 worth of programs on it (Electrical & Mechanical Engineer) and it would take me weeks if I had to start from scratch.
View 1 Replies
View Related
Jul 18, 2012
I am in the process of putting (5) 3TB HDD's into my computer (Windows 7 Home Premium 64 bit) to rip my Blu-ray collection to for playback in my home theater room via a Popcorn Hour player. Each drive is independent and I will be systematically filling one drive before going onto the next.The problem is that the Popcorn Hour players communicate with the PC by specifying one folder via SMB that contains all of my media. Since I am doing independent drives, there will be one master folder on each drive containing all of the media for that said drive. Meaning, in terms of the Popcorn Hour/SMB setup, there are five folders I need it to *see* and catalog.
View 9 Replies
View Related
Nov 27, 2010
I have W7 installed, works fine. I bought 2 HDDs and wanna add them just as data disk and set up as RAID1. If I set up RAID in bios, Windows crashes when loading with classic blue screen + restart. Is there any way to make it work (install some driver etc.) or do I have to reinstall Windows with RAID set up prior to Windows installation? I have Asus P7P55D-E board.
View 1 Replies
View Related
Apr 20, 2012
I have install xp on raid striped but when i try to install win 7 the driver i have are not the correct ones i have a dfi lanparty tu p45 t3rs mb and two wd 500gb hdd. i have looked around but cant find any others anything i can do or anone know where i can get driver
View 2 Replies
View Related
Nov 20, 2010
My PC is currently using a single RAID 0 drive that contains my Windows install and all my data in a single partition C: (I'm well backed up so happy with the risk of RAID0)
The RAID0 drive is setup by my motherboard controller so Windows just sees the one drive.
I am thinking of adding an separate drive for windows, hopefully an SSD. I would like to do a fresh install of Windows 7 on the new disk then rename the old RAID0 drive to something different such as D: . Then reorganise it into just a data disk.
My question is.. will the new Windows 7 installation just see the old RAID0 disk as another disk? I know this would work witha normal disk, but does RAID0 transfer over to a new installation ok?
View 1 Replies
View Related
Jun 11, 2011
I would like to get 2 SSDs and put them into a raid array using Windows 7-64bit, but wanted to make sure I understand how to do that. The 2 SSDs will be the only drives in the system. My computer has an X58 motherboard with an ICH10R. Here is what I think is the correct procedure: Boot into the bios. Set the storage config to RAID (the other choices are IDE and AHCI) Reboot and hit Cntrl-I to get into raid menu during boot. Set up the raid array in the setup screen. Reboot to the Windows 7 install CD and install Windows Is this correct? Are there any other steps I need or tips I should be aware of?
View 9 Replies
View Related
Jun 16, 2011
I'm trying to do a fresh install of windows 7 and it wont recognize my hard drives. I've done some research and determined i need the correct drivers, but i don't know which ones. I'm trying to install them on 3 WD3000HLFS in RAID 0. The HDD are plugged into SATA 6 ports( only 2 SATA 3 ports on the mobo).
View 4 Replies
View Related
May 26, 2012
I have been trying to get windows 7 Ultimate 64 bit installed onto a raid I created with two ocz agility 3 ssds. Everytime I try loading the drivers at install it gives me an error stating the drivers are unsigned and to install a 32 bit OS. When installing a 32 but OS, the install works normal and the computer runs fine. I am just wondering why it wont install for 64 bit considering I would much rather run 64 bit. I went to both the MoBo's website and the main companys website for the chipset drivers (AMD) but have both turned up with the same error.
MoBo = Biostar TA75M
CPU = A6-3650
2x OCZ Agility 3 60gb SSDs (2.22 firmware)
View 1 Replies
View Related
Aug 23, 2012
I have 3 driver onmy compute. which worked as 1 when playing games ex. got a virus o the shop cleanedor me.Btwo driver wrks at a time. And i need all 3working to play games. pc worldused to do it bu not ay more.
View 1 Replies
View Related
May 6, 2012
I am having trouble installing windows 7 (home premium) on my new raid array (2x intel 330 120GB SSD in RAID0). Basically, windows CAN see the raid volume. it recognies that there is a single 223 GB volume available. I select "Load Driver" for the volume, and plug in my trusty USB with the appropriate intel SATA RAID drivers. Win7 recognizes that there is a compatible driver on the USB, installs it, but still says: "Windows cannot be installed to this disk. This computers hardware may not support booting to this disk. Ensure that the disk's controller is enabled in the computer's BIOS menu". The format and create new partition options are grayed out for this volume.
Using the Intel Rapid Storage Technology tool, I combined the two drives into a raid0 volume. This is confirmed because when I restart, the raid volume shows up in the RST echo with the right size, and also indicates that the volume is bootable. It is also confirmed because the windows 7 setup only sees one 223GB disk. I have confirmed that in the BIOS, the SATA controller is set to RAID mode (not AHCI). I have confirmed that in the BIOS, the first boot option is "RAID intel SSD". I've tried the RAID drivers that came with the motherboard, Ive also tried the raid drivers available from intel and the latest raid drivers available from the motherboard MFR.
ASROCK extreme 6
Intel Core i7-3770k
16 GB RAM
2x intel 330 120GB SSD
NVIDIA GTX 680
View 1 Replies
View Related
Apr 1, 2012
As part of the chipset driver installation, it also installed the RAID and SATA drivers that Nvidia provides.I have a 300GB HDD on the primary IDE channel although I currently boot from one of my SATA hdd's.How would I go about transferring my OS to a RAID 0?Would it be possible to just system image my current OS onto the IDE drive and then format my two SATA hdd's, enable RAID in BIOS and then use Seagate Disc Wizard to install the system image onto the RAID 0?Is seagate disc wizard capable of transferring to a RAID drive??Have the RAID drivers definitely been installed with the Chipset drivers and will Windows recognise the RAID array?Have heard that you have to set up a boot partition the same size as the image on the RAID 0, would it then be possible to expand that to use the entire RAID partition
View 4 Replies
View Related
Nov 15, 2012
I recently purchased a 64GB Crucial M4 SSD and I'm trying to install Windows 7 with the Raid controller on a fresh HDD to meet the requirements for Intel's SRT. I'm trying to install Windows from a Mesh OEM disk but when it gets to the installation completion window an error pops up saying ''Windows setup could not configure windows on this computers hardware''.Windows installs fine under IDE/AHCI controller but that doesn't help me!
View 2 Replies
View Related
Jan 24, 2013
Recently completed my first computer build and am trying to install windows with a raid 0 on 2 500g HDD. I have it set up in the BIOS for 1-4 and 5-6 sata ports to RAID. When I boot from the dvd drive with the windows disk, after clicking install windows, it says: "a required cd/dvd drive device driver is missing" I figured this was a driver for the raid but i cant find it anywhere. if i select browse, there is a boot (x folder but i dont see anything in there that would help me. Do i need to download a driver to a usb stick and pull it off there? adn if yes where could i get the driver? i cant find it on the asus website.
here is my setup:
asus m5a97 LE R2.0 mobo
XFX Radeon 7870
AMD 8350 Processor
View 1 Replies
View Related
Jun 23, 2010
[code]...
So then I thought, that maybe I can't install the RAID drivers from within the OS. So I caused the BSOD on purpose once again, and then with ICH10R RAID activated and Samsung hard disks attached, I choose the Windows 7 Recovery mode in the boot menu. It sees some problem(s), tries to repair, does not succeed and does not ask for drivers (which I put on a USB stick) to install. I also tried to use the command-line in the recovery: "rundll32 syssetup, SetupInfObjectInstallAction DefaultInstall 128 iaStor.inf" but it gave "Installation failed."
So I'm clueless how should I proceed. Do I really need to re-install Windows 7 and load RAID drivers in the Win7 setup? I don't want to install any OS on the RAID, the Windows 7 is and will be on the SSD. I just want to have a RAID-1 backup using those two hard disks.
View 3 Replies
View Related
May 24, 2012
I can't get my Nokia Bh-905i headset to pair up with my computer's usb bluetooth dongle, but it will pair up with my wiimote in a second. When trying to connect the 905i headset, it's stuck on "connecting to device" screen, which I am never presented with a pairing screen. Then it reports an error 0x80004005. I have tried installing broadcom's drivers, removing registry keys, new bluetooth profile name [Device Manager > Bluetooth > Advanced Name], and pairing multiple times and rebooting.I don't understand what is going wrong, the bluetooth adapter works with wiimote, a lot of people have no problem at all pairing up with their 905i headset, broadcom's drivers is suppose to be the end-all fix for bluetooth issues, but yet nothing has fixed it.
View 8 Replies
View Related
Nov 19, 2011
Installed a new M4 ssd today and loaded windows on it. Previously i was using 2 raptors in raid 0 for the os and programs. I re raided the 2 raptors and connected them to the jmicron ports and set them up for raid in bios, then created the raid 0 array no prob. Windows doesnt see the array when loaded up and i have the latest rst drivers installed..did this prior to the os install on the ssd. using the x58 e760a1 mobo. under device manager, the raid controller has an exclamation mark and no driver installed yet i have the latest rst 10.8.0.1003 installed..
View 1 Replies
View Related
Dec 23, 2010
Ive been trying for 3 days now to install a clean os on a raid 0 setup. I can get the array setup in the bios np, but when it comes time to actually install the os i can't. Reason being i cannot for the life of me find a raid driver that is signed by windows>< The south chip is sb700.
View 6 Replies
View Related
Jan 3, 2011
I have the following MOBO:
ASUS P7P55D-E EVO
2X80gb Western Digital SATA Drives
2x2TB Samsung Spintpoint SATA Drives
I have already been using the machine with another 80Gb Western Digital SATA Drive with Windows 7 Pro 64Bit installed and now want to convert to RAID 5 for redunancy in case of Drive failure (We all say we will back up but we are all lazy when it comes to it LOL).I have taken out the original OS drive and plugged it into the E-SATA connector on the MOBO, gone into the BIOS, turned on RAID for the SATA Ports on the MOBO, and connected the 2 X 80Gb Boot drives. Entered the Hardware RAID Controller POST, and created the RAID 5 Volume from the 2 X 80Gb Discs.Now boot with Acronis Wester Digital edition.Clone the Original 80Gb Disc to the new Raid Array.Shut machine off, remove original OS 80gb Disc from E-SATA port.Boot machine.It starts to boot, and gets as far as the Windwos 7 Microsoft 4 Colour logo and then I get an error and then have to boot into Windows 7 from DVD and go through the repair process.When the Repair has run it reports the following:
The following startup option will be repaired:
Name: Windows Boot Manager
Identifier: {9DEA862C-5CDD-4E70-ACC1-F32B344D4795}
The following startup options will be added:
Name: Windows Recovery Environment (recovered)
Path: Recoverye52d0bc2-1f15-11df-af10-d764fe3715b8Winre.wim
Windows Device: Partition=D76190 MB)
A copy of the current boot configuration data will be saved as:C:BootBCD.Backup.0001 However it fails to do the update How do I get this RAID to boot successfully? I *don't* want to have to re-install the Operating System as that is just too painful a thought?
View 2 Replies
View Related
Jul 30, 2011
I have seen this question being asked a few times already. I just bought 2xSamsung Spinpoint F3 1TB drives and I created a dynamic striped partition with MBR in comuter management. If I try to install win 7, after dvd boot-up, will I be able to select the partition and install windows on it ? I know all about the advantages and disadvantages of using software raid 0. But, my question is simple. Can you just install an O/S on that type of partition (will it be detectable?) or do I have to buy a "fake raid" controller or boot some type of application first to make it detectable everytime I boot up my computer?
View 2 Replies
View Related
Sep 26, 2011
So I just recently decided to do a RAID 0 configuration on my ASUS M4A89GTD with two 1 tb drives. I first set the Raid controller to the raid 0 setting and added my two drives. The raid manager reported back the raid 0 drive was healthy and working fine.
I proceeded to go through with a fresh windows 7, 64-bit install. The install goes fine but when the computer boots up to load windows 7, it hits a blue screen and instantly restarts. Over and over again.
I think I tracked down the issue to a rogue registry entry. Apparently there is an entry called iaStorV that causes the drivers.sys file to not load the drivers correctly, causing a blue screen error.
Things ive tried: Using ubuntu off a cd. Didn't work because the chntpw doesn't know how to mount a raid 0 drive Regedit bootloading programs, dont work because they dont know how to deal with a raid drive Regedit in the system restore command prompt. Doesn't work because it's version doesn't match windows 7
View 7 Replies
View Related
Apr 14, 2012
Ho do I pair bluetooth headset nokia bh-108 to my Dell laptop having windows 7?
View 3 Replies
View Related
Sep 10, 2012
I have just bought two brand new WD 500 GB RE4 HDD's and connected them coorectly for RAID 1. I have changed the BIOS and Pressed Ctrl+F to create the RAID and this has been successful. When installing Windows you obviously get to the aprt where you need to load the floppy drivers to locate the drives...
I have downloaded ever driver from the Gigabyte support drive and loaded them onto a USB, not one driver can be seen when the USB is "Browsed" too...
How important is it that the drivers are on a floppy, as I do not have a floppy drive or access to a floppy and drives. Also what driver should be downloading as I tried the 3.2.1540.17 one and that was not seen, so I just downloaded them all in an attempt for success.
View 9 Replies
View Related
Aug 2, 2010
I have an ASUS Motherboard M4A87TD EVO, got two new hard drives, and changed the BIOS settings to a RAID configuration. After exiting BIOS, I loaded the WIN 7 (64 bit) installation disc, got thru the first few prompts of installation, and the pop up error menu shows up. "No signed Driver Found, Please insert CD/DVD/ Floppy", and my RAID configuration does not appear in the box as a hard drive for Windows to be installed into.
After researching on the web and contacting ASUS, I still don't understand. From what I can gather, it is a driver that will make THE INSTALLATION PROCESS RECOGNIZE MY RAID configuration. Apparently, it must be downloaded onto a thumbdrive and installed "during" the Windows installation. Is it specific to this type of installation, or manufacturer specific? Asus or Windows? A third party??
View 3 Replies
View Related
Apr 25, 2012
I have tried to find the way to do this, but without success as I cannot see the wood for the trees.
I have a mature Windows 7 system, with so many applications loaded that rebuilding from scratch is just not an option. I have a 300MB Velociraptor wholly given over to the OS and another empty 300MB VR. I want to extend, that may not be the right word, my OS to use both disks in Raid 0.
View 2 Replies
View Related