MOBO = Gigabyte x58a-ud5 I just got 2 SSDs I'm trying to put in RAID0 and hopefully clone my current install. When I change the bios settings to set the intel RAID controlled to xhd and raid but try to boot from my windows installation it wont boot, it gets to ''starting windows'' and then BSOD. When I turn the RAID setup off and try to install the XHD drivers the install aborts saying ''this is not a RAID setup". Is there something I can do to get the drivers installed on my current setup then clone it to the RAID drives?
Is it possible to make a clone / image of a laptop setup with all the work settings etc and run that on a mac instead of osx?I can't just install windows as all the work settings would be lost and the 'IT' department won't support macs. I know it is possible, can anyone point me in the direction of it?
I want to install a Linux Distro on my laptop. I will post as much details as possible so that you can guide me about how to free up some space so that I can create new partitions for my Linux Distro.I currently use the Linux VM images in VMWare Workstation, however there are certain tasks I need to perform which require, Linux to be installed as an OS instead of running as a VM.I have an HP Laptop which came installed with Windows 7 Home Premium OS.
There are 2 partitions:
C: Drive (Windows Installed on this one) D: Drive (Recovery)
DiskPart output:
Code: DISKPART> list volume Volume ### Ltr Label Fs Type Size Status Info ---------- --- ----------- ----- ---------- ------- --------- -------- Volume 0 E DVD-ROM 0 B No Media Volume 1 G DVD-ROM 0 B No Media
[code]....
The column alignment is not proper, but hope it's clear that which is is the System Partition and which is the Boot Partition.Now, how do I free up some space on my HDD to be able to install a Linux Distro?I need about 25 GB of Hard drive space for linux including the swap partition.
I'll make this one short. I had some time ago a GX623 laptop that had a hidden partition from where I installed win7. If anything went wrong, i just asked the laptop on startup to run the recovery manager, and boom, factory settings in 20 minutes flat (cleaned HDD). Now I am planning to get myself a reduced version of the 780DX MSI laptop (normally 2 hdds in raid 0), and i want to get a SSD as boot and a fw extras drive. The problem is i wanted to have that hidden partition on the SSD (and i plan to buy it apart and put it in myself once i figure out the laptop is stable). How to create your own hidden OS install partition...
I just purchased a new HP laptop that has Windows 7 Home Premium install setup on the hard drive. I started and completed the installation. But I don't remember during the install asking me for an Administrator Name & Password. After the installation was completed I did the Recovery Disks, but have not yet rebooted the laptop. When is the Admin Name and Password created? I remember seeing a Rick-PC during the install, but I don't remember it asking for me to input a password. Am I fretting prematurely, or do I need to reboot, or can I use the Recovery Disks to start over?
I've been using an old PC with Windows XP. And I checked out 3 books on Windows 7 at the Library.
I'm getting a new Macbook Air without an optical drive in a couple of weeks so I'm trying to create a bootable USB drive so I can install Windows 7 on it on day one (can't live without a bit of Windows 7)
I'm currently running Windows 7 on my Dell XPS M1330 which is a 32 bit install, but I want to create a 64bit bootable USB (the new version of Windows 7 I have is 64 bit and the new computer has 4 gig of ram).
When I try and do this through Microsoft's USB DVD Download tool, though, I get an error:
'Files copied successfully. However, we were unable to run bootsect to make the USB device bootable. If you need assistance with bootsect, please click the "Online Help" link above for more information.'
The online help section didn't even mention bootsect, but I'm pretty sure this is an issue because I'm trying to create a bootable USB install stick of a 64 bit version from a 32 bit version.
Does anybody know a way around this without installing 64bit Windows 7 on my computer?
I noticed on the forums over the last few months, many people for one reason or another having problems getting their DVD drive to boot from their newly purchased Windows 7 DVD disks, but given that many retails and e-tailers will not accept boxed software returns, I thought I would write up a quick guide on how to create a bootable flash drive that you can install Windows 7 from. This guide can also apply to those who can boot from the DVD, but are having problems finishing the install process.
Under computer I go to my drive of folders. When I click new folder either by right clicking or by hitting new folder the system then creates 2 or 3 new folders at one time. I then have to go back and delete the extra folders. At first I did not mind because it only happened once or twice and now it is every time.
I have W7 installed, works fine. I bought 2 HDDs and wanna add them just as data disk and set up as RAID1. If I set up RAID in bios, Windows crashes when loading with classic blue screen + restart. Is there any way to make it work (install some driver etc.) or do I have to reinstall Windows with RAID set up prior to Windows installation? I have Asus P7P55D-E board.
I've read several forum threads on this, but am still having trouble. I have win 7 32bit RC up and running for a long time on a 500 gig WD. Bought two 1Ts for a raid 0. I have the RAID chosen correctly in the BIOS, and the utility works fine. At the clean install for either 64 or 32 bit, I try to choose the drivers which I have downloaded from Intel and Asus, and tried to use the Vista drivers off my P5Q install disk, and still, Win 7 does not recognize the drive.
I have been home building and using computers for the past 25 years and I guess technology has gotten way over my hobbiest head. I have tried the USB flash drive route and I doesn't work either. Please, I know of the F8 workaround for unsigned drivers, but that doesn't work either. So, how are people raiding Win 7 at clean install?
Second question, is there a good tutorial at technet.com (which I can't find there) or someother place that tells step by step how to raid under disk manager in win 7?
I want to slick my drive and do a clean install of the RC version. I currently have a Raid 0 configuration on 2 additional drives (not the OS drive) using the Asus P6T on-board controller. Will that Raid be preserved and thus the data as well? What is the best way to accomplish this with the least amount of angst?
I want to set up a raid 0 during the install for my c partition on Win 7 can this be done? If not what I will do is install on a parition on one drive and then after I have installed set up some stripped partition and hack the registery and change the locations of the Windows folder to be on the stripped partitions after copying them of course. This is just not a very nice way of doing it. My mobo doesn't support hardware raid so that is why I am trying to implement software raid and I have a second hardrive.
I have install xp on raid striped but when i try to install win 7 the driver i have are not the correct ones i have a dfi lanparty tu p45 t3rs mb and two wd 500gb hdd. i have looked around but cant find any others anything i can do or anone know where i can get driver
My PC is currently using a single RAID 0 drive that contains my Windows install and all my data in a single partition C: (I'm well backed up so happy with the risk of RAID0)
The RAID0 drive is setup by my motherboard controller so Windows just sees the one drive.
I am thinking of adding an separate drive for windows, hopefully an SSD. I would like to do a fresh install of Windows 7 on the new disk then rename the old RAID0 drive to something different such as D: . Then reorganise it into just a data disk.
My question is.. will the new Windows 7 installation just see the old RAID0 disk as another disk? I know this would work witha normal disk, but does RAID0 transfer over to a new installation ok?
I got this problem and cannot solve it myself for over a month, ANY advice will be appreciated! The goal is Windows 7 64bit with RAID0.
1. Windows XP 32bit installs fine on RAID0 (with proper driver integrated)
2. Windows 7 64bit and Vista 64bit installs fine on single drive.
3. Windows 7 64bit and Vista 64bit on RAID0 give BSOD 0x000000F4 during completing installation stage, then Matrix Storage manager shows RAID0 ERROR OCCURRED.
EDIT:
4. Windows Vista 32bit won't install on raid setup too. Its not the case with 64bits
I tried everything I could think of:
1. exchanged both hard drives
2. tested RAM
3. tried install with minimum pheripherals and 1GB RAM
4. messed up with BIOS, even updated to latest beta bios
5. tried installing intel vista64 raid drivers, tho windows 7 has itself
6. RMA'd my DVD Drive
and still NO GO
E7200 || Abit IP35 Dark Rider || A-Data 4GB || 4850 || X-Fi Gamer || Samsung F1 RAID0 || Pioneer DVR-212 || Corsair VX450 || HP w2207h
I would like to get 2 SSDs and put them into a raid array using Windows 7-64bit, but wanted to make sure I understand how to do that. The 2 SSDs will be the only drives in the system. My computer has an X58 motherboard with an ICH10R. Here is what I think is the correct procedure: Boot into the bios. Set the storage config to RAID (the other choices are IDE and AHCI) Reboot and hit Cntrl-I to get into raid menu during boot. Set up the raid array in the setup screen. Reboot to the Windows 7 install CD and install Windows Is this correct? Are there any other steps I need or tips I should be aware of?
i want to change my existing install too raid0 i currently have install/programs on one 1tb drive and media/games on another 1tb drive, i have a spare 2tb drive unusedwhat are your suggestions so i reduce the amount of lost programs etc
I'm trying to do a fresh install of windows 7 and it wont recognize my hard drives. I've done some research and determined i need the correct drivers, but i don't know which ones. I'm trying to install them on 3 WD3000HLFS in RAID 0. The HDD are plugged into SATA 6 ports( only 2 SATA 3 ports on the mobo).
I have been trying to get windows 7 Ultimate 64 bit installed onto a raid I created with two ocz agility 3 ssds. Everytime I try loading the drivers at install it gives me an error stating the drivers are unsigned and to install a 32 bit OS. When installing a 32 but OS, the install works normal and the computer runs fine. I am just wondering why it wont install for 64 bit considering I would much rather run 64 bit. I went to both the MoBo's website and the main companys website for the chipset drivers (AMD) but have both turned up with the same error.
I have 3 driver onmy compute. which worked as 1 when playing games ex. got a virus o the shop cleanedor me.Btwo driver wrks at a time. And i need all 3working to play games. pc worldused to do it bu not ay more.
Biggest bottleneck in my system right now is my boot drive, which is a WD velociraptor. I want to change this for dual 120GB SSD's in Raid 0 configuration. Can anyone walk me through the steps to copy over the existing Win7 64 install onto the SSD's, I dont want to have to load everything again
I am having trouble installing windows 7 (home premium) on my new raid array (2x intel 330 120GB SSD in RAID0). Basically, windows CAN see the raid volume. it recognies that there is a single 223 GB volume available. I select "Load Driver" for the volume, and plug in my trusty USB with the appropriate intel SATA RAID drivers. Win7 recognizes that there is a compatible driver on the USB, installs it, but still says: "Windows cannot be installed to this disk. This computers hardware may not support booting to this disk. Ensure that the disk's controller is enabled in the computer's BIOS menu". The format and create new partition options are grayed out for this volume.
Using the Intel Rapid Storage Technology tool, I combined the two drives into a raid0 volume. This is confirmed because when I restart, the raid volume shows up in the RST echo with the right size, and also indicates that the volume is bootable. It is also confirmed because the windows 7 setup only sees one 223GB disk. I have confirmed that in the BIOS, the SATA controller is set to RAID mode (not AHCI). I have confirmed that in the BIOS, the first boot option is "RAID intel SSD". I've tried the RAID drivers that came with the motherboard, Ive also tried the raid drivers available from intel and the latest raid drivers available from the motherboard MFR.
As part of the chipset driver installation, it also installed the RAID and SATA drivers that Nvidia provides.I have a 300GB HDD on the primary IDE channel although I currently boot from one of my SATA hdd's.How would I go about transferring my OS to a RAID 0?Would it be possible to just system image my current OS onto the IDE drive and then format my two SATA hdd's, enable RAID in BIOS and then use Seagate Disc Wizard to install the system image onto the RAID 0?Is seagate disc wizard capable of transferring to a RAID drive??Have the RAID drivers definitely been installed with the Chipset drivers and will Windows recognise the RAID array?Have heard that you have to set up a boot partition the same size as the image on the RAID 0, would it then be possible to expand that to use the entire RAID partition
So like half the world I got RTM from MSDN yesterday, with hopes of installing today. Well for the past 10 hours I have been trying to get this OS installed on a Asus M4A79T Deluxe motherboard with the AMD SB750 RAID drivers and unfortunately I have come upon some woes that I hope you all might be able to shed some light on.In the RC the drivers were not present, as is the case with the current RTM, the process I would have to go thorough is as follows: 1. Click Next at the Language select screen 2. Click Install Now at the Install screen 3. Accept Terms and Next 4. Choose Custom install 5. It is at this point where I run into the lack of a driver with the RC, no drives are listed at theWhere do you want to install Windows?screen. 6. Click Load Driver 7. A message box pops up indicating To install the device driver needed to access your hard drive, insert the installation media containing the driver files, and then click OK.It is at this time that I click Browse 8. The browse for folder menu pops up and I navigate to my USB drive (have used a CD in the past) and select the AMD AHCI Compatible RAID Controllerand click Next At this point everything is good, the driver gets loaded and I continue on my merry way with the install of the RC.
The RTM, however, is much, much different: 1. Click Next at the Language select screen 2. Click Install Now at the Install screen 3. (unlike the RC, no terms yet) It is at this point where I run into the lack of a driver with the RTM, thus a Load Driver popup comes up indicating A required CD/DVD drive device driver is missing. If you have a driver floppy disk, CD, DVD, or USB flash device please insert it now. This is similar to what happened in step 7 above. It is at this time that I insert my USB key and click Browse 4. The browse for folder menu pops up and I navigate to my USB drive (have used a CD in the past) and select the AMD AHCI Compatible RAID Controllerand click Next 5. About five minutes of time and I receive the following error: No new devices could be found. Make sure that the driver files are correct and located on the driver installation media.Excuse me...what? The drivers are right there! I have them highlighted! So I click OK on the error popup and choose Browse again to repoint to the driver....but wait...WHAT? WHAT WHAT WHAT? All of my drives on the RAID controller are now showing up in the Browse box, indicating that the driver has been loaded!No matter how many times I try and click Next (not that clicking it a bunch of times is going to change anything) I cannot proceed in the install.
I just bought a refurb Dell XPS 420 w/ Q9300, running Vista Home Premium x64 and downloaded/installed an activated version of Win 7 Ult x64 on an 80GB SSD [Sata1] I bought for it; dual booted w/ Vista x64 on old hard drive [Sata0].
Windows 7 x64 was running stable and instantly fast, I wanted to enable RAID0 on the old hard drive [Sata0] and another new hard drive [Sata2]
I entered Intel Maxtrix Storage Manager (Ctrl-I), creating a RAID0 volume on [Sata0] and [Sata2].
After reboot, it says "No boot device available" after BOIS screen.
My subsequent boot attempts include (roughly in order):
1. disable RAID0 volume, boot to [Sata1]
2. disable [Sata0] and [Sata2], boot to [Sata1]
3. disable [Sata1], boot to CD/DVD-drive (Windows 7 install/boot)
4. disable CD/DVD-drive, boot to USB flash (Windows 7 install/boot)
I have done some digging around and cannot seem to find a solution. I have the use of my notebook (w/ broken DVD burner, still reads) running Windows 7 Ult x86 so apparently I cannot make my USB flash drive x64 bootable from what I've read. I also have 2-USB hard drives (80/250GB) and an eSata 2x docking station available, but no eSata on notebook.
Hope I gave enough info for someone to come up with an easy fix. If I could boot to the Windows 7 x64 install DVD that I made with the non-booting PC, I would have just done a clean install by now, but it refuses to boot to the CD/DVD drive. It actually wouldn't even boot to DVD to install Windows 7 x64 in the first place, I had to install from Vista. Also I do not have a Vista x64 install disk either.
I recently purchased a 64GB Crucial M4 SSD and I'm trying to install Windows 7 with the Raid controller on a fresh HDD to meet the requirements for Intel's SRT. I'm trying to install Windows from a Mesh OEM disk but when it gets to the installation completion window an error pops up saying ''Windows setup could not configure windows on this computers hardware''.Windows installs fine under IDE/AHCI controller but that doesn't help me!
Recently completed my first computer build and am trying to install windows with a raid 0 on 2 500g HDD. I have it set up in the BIOS for 1-4 and 5-6 sata ports to RAID. When I boot from the dvd drive with the windows disk, after clicking install windows, it says: "a required cd/dvd drive device driver is missing" I figured this was a driver for the raid but i cant find it anywhere. if i select browse, there is a boot (x folder but i dont see anything in there that would help me. Do i need to download a driver to a usb stick and pull it off there? adn if yes where could i get the driver? i cant find it on the asus website.
here is my setup: asus m5a97 LE R2.0 mobo XFX Radeon 7870 AMD 8350 Processor
So then I thought, that maybe I can't install the RAID drivers from within the OS. So I caused the BSOD on purpose once again, and then with ICH10R RAID activated and Samsung hard disks attached, I choose the Windows 7 Recovery mode in the boot menu. It sees some problem(s), tries to repair, does not succeed and does not ask for drivers (which I put on a USB stick) to install. I also tried to use the command-line in the recovery: "rundll32 syssetup, SetupInfObjectInstallAction DefaultInstall 128 iaStor.inf" but it gave "Installation failed."
So I'm clueless how should I proceed. Do I really need to re-install Windows 7 and load RAID drivers in the Win7 setup? I don't want to install any OS on the RAID, the Windows 7 is and will be on the SSD. I just want to have a RAID-1 backup using those two hard disks.
Installed a new M4 ssd today and loaded windows on it. Previously i was using 2 raptors in raid 0 for the os and programs. I re raided the 2 raptors and connected them to the jmicron ports and set them up for raid in bios, then created the raid 0 array no prob. Windows doesnt see the array when loaded up and i have the latest rst drivers installed..did this prior to the os install on the ssd. using the x58 e760a1 mobo. under device manager, the raid controller has an exclamation mark and no driver installed yet i have the latest rst 10.8.0.1003 installed..
