PC Won't Finish Booting
Jun 14, 2011windows starts to dl everything and restarts a couple of times but dont go to desktop setting u for the first time?
View 3 Replies
ADVERTISEMENT
Downloads Always Get To About 98% But Never EVER Finish
May 4, 2011I use the latest version of firefox and use Dodo wireless broadband and I can never get beyond 98% of a download, it's very frustrating when certain programs have to be updated to even run. According to dodo's signal charts I should be in the best location for their signals and when I contact them they refuse to take any responsibility for it. I wasted countless gigs on downloads that just won't finish. Is there anything I can do to make the downloads finish? I've tried disabling my anti virus, firewalls, tried using IE8, NOTHING WORKS!
View 1 Replies View RelatedNew Install Won't Finish?
Oct 26, 2010I have 2 ssd's raid-0 and 2 hdd's raid-1 connected to the ich10r. Both have or I should say had windows 7 installed. I want a back up windows on the hdd's. All was good until I decided I wanted the hdd's connected to the Marvell controller so that the sdd's and hdd's are on separate chips.I have been trying to get windows 7 to reinstall to the hdd's now connected to the Marvell 9128 all day. It won't finish the install. It goes all the way through to the last step, reboots and I get: (File:BootBCD. Status: 0xc0000225)
View 5 Replies View RelatedIt Won't Finish Updates On Restart
May 12, 2011I'm having an issue with updating my system. My computer installed some updates and wanted me to restart to fully update the system. When I turn the computer on now it shows it's updating (it never progresses past zero) and it doesn't finish the update. Now every single time I go to start my computer it constantly has to try and finish these updates. The computer will sit there for a good few minutes trying. I have no idea what the updates were.
View 2 Replies View RelatedWindows 7 Could Not Finish Configuring The System?
Jan 14, 2009resume configuration restart computer" i have more than enough to install this is a clean install on a 60 gig PATA HD. my pc is a P5N-E SLI asus MB.. 8800gt 512 MB video card. 2 gig pc6400 ram.. and theprocessor is e6850 dual core. so what gives?? i get no other info other than listed and when i reboot i get the same message?
View 9 Replies View RelatedDuring Install Windows Would Not Finish Installation
Jan 1, 2011I have just up graded the ram on my PC and Installed Windows 7 on a second hard drive. During install Windows would not finish installation. After two days of tearing my hair out I started stripping everything off the PC leaving only the bare essentials for running. This included removing one of the two sticks of Ram. Win 7 installed and is working perfect, duel booting with XP on two HDD's.The problem, put the second stick of Ram back in XP boots and runs perfectly but reboot to windows 7 and it freezes on the startup screen. Take it back out and it works no problem.
View 2 Replies View RelatedWhy Wont Windows 7 64 Bit Finish Installing
Feb 24, 2011Cant get Windows 7 64 Bit to finish its installation.Gets to the first reboot.Thats as far as it gets.It wont finalize the installation.From there it goes into a reboot loop every 30 sec.Reboots into the Safe Screen window.None of the functions in the window work.Did a Custom Install from the DVD several times.No luck.Windows 7 32 Bit installed and ran fine.Did a repair from the DVD as well.Solved nothing.Asus P5W DH Deluxe (MB)Core 2 Quad CPU (Q9400@2.66 GHz)ATI X1600 Pro Video cardSound Blaster Sound CardRam 4GB
View 6 Replies View RelatedWindows Could Not Finish Configuring New Image
Mar 20, 2012So I created an image earlier this week, sysprepped it and captured it after restarting the computer.Settings were OOBE / Generalize / Restart.When the computer had finished capturing the image to deploy studio, it restarted and went through the normal 'first run' procedures, but stopped during the configuration process saying:"Windows could not finish configuring your system. Restart the computer to try again" or something similar.I had a look at an earlier thread on here but the answer was similar to 'If you sysprep more than 3 times now it won't work'.
View 2 Replies View RelatedCouldn't Finish The Sentence W/o Busting?
Jun 26, 2012So, is this the typical UBI Shoddy, unoptimized, buggy Game or have they finally turned the corner? Bwahahahahaha... sorry, couldn't finish the sentence w/o busting a gut laughing eriously though, aside from the Third Person View (that I hate with a passion because it makes moving so cumbersome), has anybody played the campaign yet?
View 9 Replies View RelatedHow Can I Freeze Cmd Screen End Of The Program Finish ?
Nov 26, 2009im using microsoft visual c# program under windows 7.
my generated application use in cmd screen but this programs just open and close fastly. i dont freeze commnet line end of my programs. that reason i didn't see my programs results.
how can i freeze cmd screen end of the program finish?
Windows 7 64bit Does Not Finish Installing?
May 7, 2012When I try to install win 7 64bit it won't complete the install. The screen is blank and it will stay that way for over an hour. I have read many post on this site about that problem and have tried many of the answers that were given (only having one drive connected, using only one stick of ram etc). but it still will not install all the way to where you name the computer and put in a password. When I reconnect the other drives and boot into my win 7 32bit os and go to computer and check the drive that I was trying to install the 64 bit os the files are there. Of course under users there is only Administrator, default and public. I have tried 3 different install disk that I borrowed from other people and the same thing happens.
View 9 Replies View RelatedReal Player Download Never Finish?
Apr 7, 2012I have real player and I'm sure you guys are aware that it has an add on that allows you to download videos of the internet. Well, every time I download a movie, my movies never seem to finish. The download tab says they're done downloading, but once I play them they are usually only 1/3 or half of the movie downloaded.
View 5 Replies View RelatedWindows 7 SP1 Unable To Finish Browser Surfing
May 24, 2011Using any browser starts the online connection, etc. then seems to stop though it still shows it trying to connect to the requested website. Tried, on IE9, Chrome and Opera, it jsut seems to stop or spin it wheels.The odd thing is updates either by MS own or pgm. updates seem to go through provided on their own update procedure, like AV or pgm. update. The last update was .Net one, is that possible causing issues.Anyways, I maybe forced to return to some restore point, if no solution is found. I understand SP1 can cause some problems, but haven't heard of this. Seems odd is I can still update with MS update service(auto).
View 2 Replies View RelatedPause Shutdown To Let Active Process Finish
May 30, 2012I have a process that is always running on my PC (Win7 sp1) that I can shutdown gracefully anytime and will also shutdown gracefully when the computer is restarted or shutdown if only it is given enough time. I'd like to add a little time (maybe 20 seconds) between the time the computer sends the shutdown command to all open processes and the time it sends the kill now command to any processes that are left open.If my process shuts down gracefully it restarts in about 5 seconds, but when it shuts down ungracefully it takes about 10 minutes.
View 3 Replies View RelatedNew Laptop - Windows Could Not Finish Configuring The System
Sep 25, 2010I ordered a refurbished/reconditioned Packard Bell EasyNote TJ74 laptop from a very well known retailer in the UK called Currys. I received it two days ago. Initally, the laptop stayed on for all of about 5 seconds before shutting down, however I have solved that problem by Googling the text and looking here: pxe-e61:media test failure check cable. It was basically trying to boot from something other than the HDD itself, so I set the HDD to the top of the list in the BIOS.Then, the next problem I got was this: I get the "Windows is Starting..." screen, and then a setup services starting message, and then this:"Windows could not finish configuring the system. To attempt to resume configuration, restart the computer."I restart the computer and... nothing happens. No Windows installation/recovery disk came with the laptop.So, I set the laptop to boot from CD in the BIOS and, using a 64-bit edition recovery disc I found online and ran startup repair using it, apparently no problems were found, and I got a message about ensuring I didn't have any cameras etc. attached... ..Someone online recommended I disable digital driver signing, so I did that by pressing F8 at one point when it was booting... it doesn't seem to have made any difference. Safe mode doesn't work either.Currys have told me they can do nothing but send a courier to my house to pick up the laptop... I don't get a replacement, simply a refund. I needed this laptop for Monday as I start university.I've set it back to boot from HDD and I'm getting the "Windows could not finish configuring the system, please restart" message again and again and again, and the system just constantly restarts and the same message appears. It is a never-ending loop!
View 4 Replies View RelatedWindows 7 Installation Could Not Be Completed - Restart To Finish
Jan 3, 2013I was trying to format my computer, I had installed the OS of Windows 7 Ultimate x32 bit, and decided to take the opportunity to install a new one, but this time of x64 bits, this was my first time formatting my computer but apparently didnt finish good.
1: When first restart the computer to finish installing the OS, it Said That "The intallation of windows could not be completed. To finish installing Windows, restart the installation"
2: I try to do what it say, but when I try to restart the installation with the OS disk in, I get to the same window (not sure if that's what meant by what I just explained).
3: When I turn on my computer says something like: "select the operating system you want to use", and I get the "Windows 7" option twice.
I just found out according to format the computer i had to delete the partition that was the old OS and create a new one, but I cant get to that window, because as explained in section 2 always get the same message from section 1.
Uninstalling Programs Won't Work - Wait For Other One To Finish
Sep 13, 2011I am trying to uninstall some programs on my computer but every time I try, I get this same message. Of course I have rebooted my pc, and the other more obvious issues concerning this but every time I go in and try it does the same thing. I really need to get some programs off my pc! Box that comes up that states that I have to wait for the other program to finish uninstalling before I can do another in which it never is finished. It just sits there like that.
View 1 Replies View RelatedWindows 7 Starter Updates Won't Finish And Can't Be Cancelled?
Jan 3, 2013I've updated every time windows has told me to, and I haven't had any problems and they usually finish really quick, but this time it's stuck on the start up screen and just says something along the lines of "update 20 of 76 don't turn off the power or unplug" but it's been installing update 20 for 3 hours so I turned it off. Well actually I took the battery out because pushing the power button did nothing. Probably not the smartest thing to do but I was desperate. Even after it turned off, it just resumed the update. I can't do ANYTHING while it's updating, and I don't even know if I downloaded this update because I remember seeing a tray icon that said "downloading updates: 0%" not long ago.
View 3 Replies View RelatedCan't Finish Registration With D-Link And Windows 7 Dlink
May 16, 2011My friend wanted a faster router for her new computer and she's using Ethernet now, but she is having hangups during the registration of both her new D-Link router, and her new Dazzle card that she is installing for direct TV purposes. She has Internet through her old router, Linksys, but she says it's too slow, so she got the new one. But in both cases, she hasn't been able to complete the registration process with either new item. It kicks her out after the first page, she says. She has windows 7 on a brand new, fast computer. She has viper as a virus protection. Someone else was trying to help her recently. She does not know where to start to find the problem. She fears this person may have inadvertently locked her out of completing the process, or.
View 5 Replies View RelatedHow To Finish Auto-login In Explorer Of Windows 7
Mar 15, 2012I am using windows 7 home premium. If I use one login name and password in explorer it remeber automatically and did not even ask before login next time
View 1 Replies View RelatedClicking Finish Button Showing Error?
Jul 26, 2012when i click the finish button there shows "the operation you selcted will convert the selected basic disk to dynamic disk."
View 1 Replies View RelatedSysprep Fails / 'Windows Could Not Finish Configuring The System'
Oct 31, 2012message after Sysprep stating "Sysprep Fails After Deployment With: Windows could not finish configuring the system."This is a new out-of-box Lenovo T530 laptop, it came pre-loaded with Windows 7 Pro.I pulled laptop from box and inserted our Windows 7 Pro SP 1 disk and installed our copy. I then configured all settings and applications under "audit mode", created an "Unattend.xml" file using the WSIM, and copied that file into the Sysprep folder and ran "Sysprep /shutdown /oobe /generalize /unattend:unattend.xml" The error message appears after I image drive using Ghost GSS 11.5.1.2266. (I'm assuming the error would appear after boot-up regardless of imaging the machine)I have read numerous articles regarding this error and have also disabled the "Windows Media Player Network Sharing Service" as suggested by many. I'm also assuming that the "Hotfix" for this issue does not apply since I am installing SP1.I am able to boot into the machine after attempting to boot into "safe mode" first (as suggested by many users), however once in, it looks as if the XML file is completely ignored.
View 5 Replies View RelatedLaptop Won't Boot Up - Startup Repair And System Restore / None Will Finish
Oct 21, 2012My Sony vaio just turned off last week and wont boot up. It turns on an flashes Sony vaio but that's all. I made a recovery disk and I can get into bios so I tried booting from internal disk and tried startup repair got nothing, tried system restore for every restore point and none will finish. Took each piece of ram out an tried starting it up to see if bad ram was the problem and it starts the same way. I also tried the restore from previous image but I have no image. So I don't know what else to try. Windows 7
View 15 Replies View RelatedSeagate External Hard Drive, Starts Up But Doesn't Finish?
Dec 1, 2012I have a Seagate GoFlex Desk 3TB external hard drive. I got it about.. 6 months ago and I've never had a problem with it up until last week. I plugged it in and it started making a normal fan sound like is usually does, then after a few seconds it stopped which made it seem like it was shut off.
View 4 Replies View RelatedWindows 7 Booting Not Show Xp At Booting Time
Jun 19, 2012Earlier xp but after win7 the booting not show xp at booting time
View 1 Replies View Related"Sysprep Fails After Deployment With: Windows Could Not Finish Configuring The System...."
Oct 30, 2012Getting the message after Sysprep stating "Sysprep Fails After Deployment With: Windows could not finish configuring the system...."This is a new out-of-box Lenovo T530 laptop, it came pre-loaded with Windows 7 Pro.I pulled laptop from box and inserted our Windows 7 Pro SP 1 disk and installed our copy. I then configured all settings and applications under "audit mode", created an "Unattend.xml" file using the WSIM, and copied that file into the Sysprep folder and ran "Sysprep /shutdown /oobe /generalize /unattend:unattend.xml"The error message appears after I image drive using Ghost GSS 11.5.1.2266. (I'm assuming the error would appear after boot-up regardless of imaging the machine)I have read numerous articles regarding this error and have also disabled the "Windows Media Player Network Sharing Service" as suggested by many. I'm also assuming that the "Hotfix" for this issue does not apply since I am installing SP1.I am able to boot into the machine after attempting to boot into "safe mode" first (as suggested by many users), however once in, it looks as if the XML file is completely ignored.
View 2 Replies View Related"Windows Could Not Finish Configuring The System, To Attempt To Resume Configuration, Restart The Computer"
Feb 28, 2012During a full system restore of my computer i didn't realize it was not charging and left it to finish the restore. Shortly coming back later, it had died so i rebooted it. During the reboot, it did its normal process well restoring," Setup is starting services.", but then during the process when gathering windows data to restore the computer in its final stages, it gives me the message" Windows could not finish configuring the system. To attempt to resume configuration, restart the computer." Shortly after starting my computer, going through the same process, it gives me that message again, and then it repeats, and eventually of course, goes into a circle of completing the same issue.
View 2 Replies View Related"could Not Finish Installing Due To A Higher Version Already Running"?
Aug 21, 2012i have windows 7 my cpu is 2 yrs oldi had problems with I E and was told to delete it and download it and re install it.i went into add/remove and removed I E.@ms.com downloadedIE9
started to install got msg "could not finish installing due to a higher version alreadyrunning"we searched several ways and I E is not on this cpugeek squad is stumped (which i am finding out doesn't take much anymore)they want me to send in the cpu for a $300. checkup and more if they have to fix iti may have been born at night but not last night..there must be another way.
Booting From SSD?
Jan 6, 2013I have four physical drives in this system. Until last month, I was booting from a drive with three partitions, C:, D:, X:, where C:contains Windows 7 Pro; the others are data. The other physical drives are also data (not bootable). I added an SSD and cloned C: onto that drive with Acronis Trueimage. In order to get it to boot, I had to add an entry to the BCD on what should now be the old c: and keep that as the boot drive in my BIOS. I'd really like to NOT be reliant on that spinning drive to boot, so I found EasyBCD. Booted from the SSD, I told EasyBCD to designate c: as the boot drive.When I tell the BIOS to boot from the SSD, I get a Disk Read Error. So I go back to booting from the spinning drive.
View 3 Replies View RelatedBooting From USB Instead Of DVD?
Jan 15, 2013Booting from USB instead of DVD, I wanted to boot from the USB instead of doing this from the DVD knowing that the DVD contains the Windows 7 Operating system. All what I did is copying the DVD to the USB.
I managed to give the USB the first option for booting, nevertheless, the machine doesnt respond to boot from the USB
What might be the issue? What should the USB contain to be bootable?
W7 Only Booting With DVD
Oct 27, 2009I guess the problem is related to the setup and installation process I'll leave it here, feel free to move the thread though.
I downloaded Windows 7 from DigitalRiver, made a bootable .iso, burned it and started the setup. I then formatted C: where Vista was located and had Windows 7 installed onto C:.
It works perfectly with the DVD inserted, but whenever I try to boot without the DVD the Bios says something like:
file:/windows/system32/winload.exe
status: 0xc0000428
Info: windows cannot verify the digital signature for this file
What I did now was to go to the setup and open up a command line and then I did chdsk /R which said the partition was NTFS, could not be locked and that it was read only.
Then I did ScanOs which gave me 0 installations found. Afterwards FixMbr and FixBoot which were "completed successfully" and last but not least RebuildBCD which said 0 was fixed but it was again completed successfully.
Long story short, nothing has changed. Still the same error.
Plus: After that message in the bios I can press either esc or enter. Enter will then get me another screen where I can choose the OS I'd like to boot and it only says Windows Vista there but that selection takes me back to the initial "digital signature blabla" screen.
So, is there still a little part of Vista left somewhere that messes up the boot process or what's up?