New Disk Drive - Cloning One Partition Of Multi-part Drive?

Aug 13, 2012

I have a generic System 7 64 bit system with a 1 TB SATA drive. It has one hard drive which I have partitioned into 4 partitions, with C: being where I put all the system software. The board has mulitple SATA ports.Change considered: cloning the C: partition onto a new SSD so that I can get the performance boost of an SSD. There are some heat problems with existing hard drive so I probably need to change it out, so I would also like to clone the D:, E:, and F: partitions to a new hard drive.I have cloned a single physical drive to another physical drive, and the software (Ghost, or the like) usually handles it ok, so that all I need to do is adjust some partition sizes, and then disconnect the old hard drive and everyting is good. This includes cloning a single hard drive with multiple partitions to being cloned to a new single hard drive with identical numbers of partitions.Compared to my prior experience, is there something different about cloning one partition only vs cloning the whole drive. My proposed plan is:

1) Install SSD
2) clone C: to SSD only
3) clone D: E: F: of old drive to new drive.
4) remove old drive.

View 5 Replies


ADVERTISEMENT

Cloning C Drive And System Reserved Partition?

Jan 7, 2012

I installed a new ssd drive and cloned my c drive onto it. It also cloned my system reserved partion [about 25 megabytes].I then, at a later date, cloned my c drive [now my new ssd drive] again back to my old primary drive so that i have an up to date copy of my primary drive. But it also cloned my system reserved partion. Can i delete some of these system reserved partions. I now have 3 of them! It makes my computer look very untidy. What ones should i leave or do i need to leave them all?

View 1 Replies View Related

Partition On Part Of Hard Drive No Longer Recognized?

Sep 23, 2012

I've had my partitions over several drives set for many months. Suddenly on boot this morning, one of the partitions isn't recognized by Windows (7 64-bit). My partition software (EaseUS Partition Manager Pro) does "see" it and shows the correct division of used and unused space. This is an NTFS partition with 11.86 GB capacity and 2.50 GB used. The status is None and the type is logical.The error message box title is "Location is not available". The message is:H: is not accessible.The file or directory is corrupted and unreadable.I've had no activity in this partition for several days. The partitions on either side are fine (fingers crossed they stay that way!). They same the same characteristics (although obviously different capacities) as the missing partition.

View 1 Replies View Related

Move Partition To The Front Of The Disk (the Fastest Part)?

Jan 11, 2011

Atm I have 500GB array from two 250GB in raid0 with Vista on it... its using up about 90GB of space (leaving around 375GB free) and I want to shrink the partition to say 100GB (see below). Then I want to reformat the unallocated space (~350GB) to be used by my Windows 7 install on my SSD. I know you can use the Disk Management in device manager to do all this but I want the 350GB free space partition to be at the front of the disk (the fastest) and have the old 100GB Vista partition right at the end (in the slowest part I guess, which its ok cos I will rarely boot into it).

About above... just wondering when I shrink the partition to 100GB even though it is only using 90GB is 10GB a good enough buffer for windows to not spaz out? Or is it even too much can I get away with just 2-3GB buffer... I wont be installing or writing anything new to it. It will be mainly just for reading data and booting.

View 6 Replies View Related

How To Partition The Disk Drive

Jun 25, 2012

When i did partition by disk management. it allowed me only to partition 226 gb space.so now in my e drive there is 226 gb n in c drive 227gb space.actually i want to keep in c drive 100 gb and make another drive of 100gb but whenever i try to shrink it doesn't allow to extend.

View 3 Replies View Related

Drive E (Hard Disk's Second Partition) Is Lost?

Aug 14, 2010

My Drive E just lost from my computer! I don't know how did it happen. I try to search through google but I can't find a solution.

View 9 Replies View Related

Partition Disk Cant Talk To Hard Drive?

Aug 10, 2011

want to just re partition the computer but the computer keeps saying unable to talk to hard drive due to me getting rid of a certin partition

View 1 Replies View Related

Windows 7 - Partition Hard Disk Without Formatting Drive C

Aug 6, 2011

I bought new hp laptop.. it came with 500 GB harddisk, windows 7 home basic, I didn't get any windows cd apart from recovery in hard disk. My windows is installed in c: and that is the only drive that it have... now the situation..

1) I want to partition my harddisk without losing windows means I don't want to format C: drive
2) I also want to install linux in dual mode with windows..

Second question is related to first one because I don't need any method that may lead to situation like I can't install any other operating system.

View 14 Replies View Related

How To Partition Hard Drive Disk Without Wiping All Data

Oct 16, 2011

How I could partition my internal hdd without wiping all data from it, and then sharing the partitioned drive within my home network. Also, I was wondering how I could tell what drive letters are already assigned to my laptop's usb ports.

View 2 Replies View Related

How To Create Another Bootable Partition From Hard Disk Drive

Feb 10, 2012

i want to create another partition, which can be bootable. so that i will be able to boot from ubuntu as well as windows 7....

View 3 Replies View Related

Fail To Format Disk 0 Partition 2 After Trying To Boot From Cd Drive

Apr 29, 2012

basically a bad partition will not allow me to wipe the computer clean, boot XP from the drive or add/change bios screen...i don't have tje kind of cash to buy or pay for repairs. what can i do?

View 1 Replies View Related

Partition (E Drive) Missing - Does Not Appear In Windows Disk Management Tool

May 26, 2012

In my Sister's laptop, running Windows 7 Ultimate x86, all of a sudden, while she was working on the computer, the "E drive" went missing which was a partition on the hard disk (I don't remember if it was a logical or primary partition). She tried restarting the system but to no avail. So, I told her to open the "Disk management" tool in Windows 7 to see if the partition is visible in there. I did this because sometimes, in my computer, my expansion drive wouldn't show but it would be visible in the disk management tool and all I had to do was to re-assign it a drive letter. But, in this case, it wasn't visible over there.

So, now I told her to download "Mini-Tool Partition manager Home edition" and install it on her laptop. On running it, it wouldn't show the partition either. It would just show "C:", "D", "System Reserved" and unallocated space. However, when I added up the size displayed by C:, D:, System Reserved and Unallocated, it doesn't add up to the actual hard disk size. It means the partition is somewhere there but not visible. Is it possible that the partition would show up correctly if the laptop is booted into the bootable image of Mini-Tool Partition Manager?

View 5 Replies View Related

0MB Flash Drive - Partition Type RAW Showing In Disk Management

Jun 3, 2011

How to force format a flash drive? I have an 8gb flash drive and I plugged it in to a speaker that plays mp3 songs. But after unplugged it, my flash drive prompts "Please insert disk" and 0mb in my computer. I tried to view it with disk management and I saw its partition type was RAW.

View 6 Replies View Related

Cloning: Destination Drive Not Being Partitioned?

Jul 22, 2012

I am trying to use Seagate discwizard, to clone my hard drive to another. When I went through the process, the new HDD received only the C partition and not the D.

I really don't want to format the hdd and reinstall!

View 2 Replies View Related

Post Cloning Of OS Hard Drive

Oct 15, 2011

I have on my laptop (a thinkpad, from Lenovo) Windows 7 Professional, obtained via something called "MSDN Alliance" and my university. A few weeks ago, I finally had the opportunity to upgrade my hard drive. Thus, I placed the new disk in a USB case, plugged it in via USB, and performed a disk clone via a software from a company called EASUS. I then removed the old disk, placed the new one in its location (that is, inside the laptop), and removed the USB equipment. Good as new, I though. And everything appears to be working fine -- except the "nag screen" that seemingly randomly pops up out of nowhere and tells me that I am using a (I don't recall the text exactly at this moment) less that legal/legitimate installation of Windows. I can check if Windows has been activated -- and it has (of course, I did this after having installed it) (i.e., on the "old" disk), I have tried searching for solutions, however I only find issues when similar clonings have changed the drive letters.

View 9 Replies View Related

How To Allocate Part Of Hard Drive That Is Unallocated

Nov 1, 2011

How do I allocate part of my hard drive that is unallocated ? I have 128 gb allocated and 104 unallocated some please advise d davies

View 1 Replies View Related

Cloning A Laptop Hard Drive And Using New Hardware?

Sep 7, 2012

I've got a laptop with a piece of really expensive software that is not transferable. As this software has been upgraded over the years, it has required more system resources in order to run smoothly. I am running Windows 7 UltimateIs it possible to clone the laptop's hard drive onto another one and place the new hard drive into a computer with better hardware???What would be the best software for this or is it ok to just use Windows 7 System image utility?

View 6 Replies View Related

Windows 7 64 Bit Cloning On To Blank Hard Drive

Jul 29, 2012

I have this current set up on my computer: 250Gb HDD ( C drive) - contains windows 7 64 bit OS, steam and other files. 360Gb HDD ( D drive) - Partially deleted and defunct windows vista. Some games and files on.

I recently purchased a 3Tb internal HDD, and wish to create the following setup:

3Tb internal HDD (C Drive) - contains the 250 and 360 GB HDD's cloned onto it. 250 and 360 Gb HDD's - Completely wiped and used for backup and storage.

I would also like the 250 and 360 Gb HDD's to be recognised seperately, AS IF they were seperate drives, while remaining on the same 3Tb HDD.

I can only use free software. I also do not want a RAID setup.

View 1 Replies View Related

Cloning C Drive And System Reserved Portion?

Dec 26, 2012

I installed a new ssd drive and cloned my c drive onto it. It also cloned my system reserved partion [about 25 megabytes]. I then, at a later date, cloned my c drive [now my new ssd drive] again back to my old primary drive so that i have an up to date copy of my primary drive. But it also cloned my system reserved partion. Can i delete some of these system reserved partions. I now have 3 of them! It makes my computer look very untidy. What ones should i leave or do i need to leave them all?

View 1 Replies View Related

Extra Used Space After Cloning A Drive With Acronis

Jan 15, 2013

I have just cloned my d: drive, 500 gb to a new 1 terabyte drive f:

drive f: has 49 gig more used space then cloned drive d: users on drive f: is 39 gig larger than users on drive d: the d: drive also has around 50 gigs less used space.

all the other folders are the same size, so not only have I cloned, somehow an extra 49 gb to the f: drive but 10 gb seems to have 'gone'! I used Acronis True Image WD Edition and everything appeared to go well. I don't want to format my other drive as extra storage until I have some idea what has happened.

View 2 Replies View Related

Cloning A Hard Drive With Windows 7 Installed?

Jun 11, 2012

My company clones hard drives for deploying our software (each software comes with a new computer and a new windows license). We clone the drive to avoid installing the mother board drivers, windows updates, sql server, etc etc each time. This worked great with Windows XP but with Windows 7 we get a boot error on the clone: "Windows failed to start. A recent hardware or software change might be the cause. To fix the problem..." We are a small company and it really is a pain to re-install everything for each new release we do.

View 4 Replies View Related

Windows Won't Start After Cloning Hard Drive

Feb 1, 2011

i just cloned the OS hard drive in my computer from an 80GB to 160GB (both IDE) using acronis true image enterprise edition.

the clone process completed fine, but when i try to start the computer with the new hard drive plugged in (power and data cables disconnected from the old drive) i get the 'disk boot failure, insert system disk and press enter' message when the OS is supposed to startup.

i booted to the windows 7 OS disc and chose the repair option which detected that there was a startup issue with the disk and apparently fixed it, but when i restarted the computer i still get the same error message. i also used the startup repair option from the windows OS disc but it didn't detect any issues.

the interesting thing is that i can boot the new hard drive while the OS disc is in the DVD drive, but if i take it out i get the message again. i've also tried changing the jumper settings on the hard drive (master/single to cable select) but that didn't make a difference.

View 9 Replies View Related

No Success With Cloning Hard Drive With Norton Ghost

Sep 16, 2012

I want to clone my existing laptop hard drive to a hard drive that I have encased as an external hard drive. My current HD is in two partitions - C: and D:. Norton Ghost told me that I would have to copy one partition at a time. Fine. After I copied C:, I went back to copy D:, but before beginning it says - warning/any existing data on the destination drive would be deleted. So how am I supposed to move one drive at a time? I don't want multiple partitions on my new HD if I can help it.

I went ahead and began copying D: onto my external drive, and when it was done, I now can't see that drive in Windows Explorer. In Disk Management I see the drive, but it looks like there isn't any data on it from the amount available. So it looks like I"m back to square one.

View 5 Replies View Related

How To Configure RAID-0 On 2 Partitions / 1 Part Is On Boot Drive

Mar 5, 2012

I have 2 SSDs each partitioned into 80GB and 40GB like this:

-Drive1-80GB (boot) and Drive1-40GB
-Drive2-80GB and Drive2-40GB

Drive1-80GB is already the Windows 7-64 boot partition for the system. Can I configure a software RAID-0 with Drive1-40GB and Drive2-40GB? I know this is unorthodox but I wanted to try this for a few reasons.

View 4 Replies View Related

Cloning To Western Digital External Hard Drive

Jan 15, 2013

i've been asked to set up 6 brand new Dell laptops bought for my software engineers in the industy - i have been given a 7th Dell laptop same as the other 6 which has had all the required software needed by our engineers for the machinery programing process installed on it - i've also been given a 1TB western Digital {USB connected} external hard drive for cloning the software and transfering it on to the other laptops, so this afternoon i cloned the 7th laptop with all the software on it using system back up - creating a system image file on the external hard drive, but when it came to transfering this image on to the other laptops, i thought i'd beable to restore {set up the C: drive} the new laptop from the file path E: {the external hard drive path} but it doesn't have the option {E: drive or USB input or external drive} only system restore/back up disk or network path, i can't use the network path as the company has access/permission,firewall blockers that basically stop our engineers laptops from working on customers sites when online, which kind of stops any work from happening, and is why the company.

View 6 Replies View Related

Cloning Program Drive And Data Drives From XP To Windows 7 Laptop?

Sep 28, 2011

I am trying to moved everything---program files as well as data files---from one laptop to another. The source is XP, the destination Windows 7 Home Premium 64. From what (little) I understand, most imaging programs clone everything, including the XP register and boot drive. But how can you then boot the Windows 7 machine to run the programs that were originally instaled in XP?I know I can just drag over the data files and re-install all the software, but I am not sure I will live long enough to complete that task.

View 2 Replies View Related

How To Create Multi-boot Flash Drive

Apr 14, 2012

Does anyone know of a way to take several different ISO's (multiple Windows ISO'sUbuntu, Hiren's Boot CD, etc.) and put them onto a flash drive from which I can boot and select one?I've tried several different utilities thus far - unetbootin, YUMI,XBoot - but none have allowed me to successfully add all my images.

View 1 Replies View Related

Super Multi Drive Installer For Windows 7?

Jun 2, 2011

Can I use the Super Multi Drive Installer which was designed for XP on Windows 7.where I can find the right Software for Win. 7.

View 1 Replies View Related

Import Favorites Saved In The Folder In D Part Of Hard Drive Into Mozzilla Firefox?

Dec 23, 2011

How to import favorites saved in the folder in D part of hard drive into Mozzilla Firefox?

View 2 Replies View Related

Portable Super Multi Drive LG DVD Player Will Not Work With PC

Jan 19, 2012

I have an LG portable dvd player. Never had a problem using it before, had some repairs done on laptop and now can not view any movie on laptop, even using power dvd?

View 4 Replies View Related

Lg Portable Super Multi Drive Install Disc?

Jul 6, 2012

i bought my Portable super multi drive some months ago, and now my laptop is becoming lower and lower so i wanna redo it. change an explotation programm as widows XP, i have the portble but i lost my cd. i dont know what to do. so i was wonderinf whever i could download an installing cd by internet, to configure my laptop after changing the exploration system?

View 5 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved