I Want Auto Trim But Installed Matrix Storage Driver!
Jan 2, 2010
I installed yesterday my new Windows 7 32bits i put it on my new Intel 160gb gen 2 with 02HD firmware and started installing drivers.
I installed Intel SSD Toolbox - v1.2 just for curiosity because i know i didn´t need it for trim, i read agood part of the manual (requirements and similar stuff) and i thought i was ready to install the Intel SSD Toolbox - v1.2. AFTER other stuff i decided to see a little more of the toolbox manual and I FOUND IN PAG 13!!!!!!! THAT ONE SHOULDN´T INSTALL matrix storage driver BECAUSE THEN ONE REALLY NEED TO USE THE TOOLBOX for trim!!!!!!!! IT SAYS THIS IN THE Schedule SECTION!!! (INSTED IN THE BEGIN WITH EG THE TITULE I M P O R T A N T):
6. If your PC uses Microsoft Windows 7 and the Intel Matrix Storage Manager version 8.x (which can be used in place of the Microsoft AHCI driver), then the Intel SSD Optimizer tool is required to enable the ATA Data Set Management Command (Trim).
NOW I LOST LOTS OFF HOURS AROUND THESE, INSTED OF EXPLORING MY NEW OS AND SSD ONLY TO FIND THAT althoug i uninstaled this matrix thing I NEED TO REINSTALL THE OS BECAUSE matrix storage driver MANUAL SAYS THAT TO REMOVE THE DRIVER ONE NEEDS TO REINSTALL THE OS!!!!!!!!!
Does someone knows a workround this ANNOYNCE? i have already lots of stuff installed and configurated
i don´t use raid but i want AHCI (I HAVE IT ENABLED IN THE SATA CONFIG IN THE BIOS before the OS install) I cant see Intel(R) SATA AHCI Controller in the 'IDE ATA/ATAPI controllers' entry in device manager but i see this:
View 5 Replies
ADVERTISEMENT
Dec 15, 2011
I'm trying to download the latest Intel Matrix Storage Manager. I'm using Windows 7 HP 64 Bit. I went to Intel and downloaded the one I thought was for my operating system but when I tried to install it I was told that my OS was not the right one for that download.
View 1 Replies
View Related
Oct 23, 2009
I am using an Asus x58 P6TDeluxe and running Windows 7 x64 OEM. I have tried installing the chipset driver and intel matrix storage manager driver (to get SAS working) but both say "Does not support this operating system WNT_6.0P_64_MCE" and "This computer does not meet the minimum requirements for installing this software. Setup will exit".
Tried using 32,64, vista, 7, everything.
Can somebody shine some light on my situation?
View 7 Replies
View Related
Mar 23, 2011
I am going to be getting 2 new WD10EALS drives in the next day or so. My plan was to put them in raid using the onboard ICH10R controller on my mobo (an ASUS Sabertooth X58). I had wanted to run WDTLER to turn TLER on, but after reading some reviews it seems I might not be able to as it is reported WD disabled TLER on these drives completely.
Im curious if there is a way to change the timeout for the drives in the matrix storage controller? So if I do have an issue my raid won't die (I'll be using these drives in raid 0 for gaming only). I dont care about the data, I just don't want to have to go thru the hassle of reinstalling the games should a drive get dropped from the array. I am thinking about getting a wd green 2tb drive for backups but just curious if there is a way to change timeout via the controller.
edit: And by change timeout I mean how long the controller waits for the disk before dropping it from the array, like could i set it too 2.5 mins just to be sure?
View 1 Replies
View Related
Jun 17, 2011
After completing the Windows 7 64 bit install, the screen goes black with a white blinking cursor. After rebooting the screen freezes at the �Starting Windows� screen which should proceed with the configuration of the Windows 7 install (select computer & user name, etc.) Before the �Starting Windows� screen there is the following message: �Boot from AHCI CD-ROM� or something similar. This was not present when XP was running successfully. Throughout this process I ran into a BSOD which mentioned iaStorV.sys which apparently relates to the Intel Matrix Storage Manager as explained here.
Action Taken:
-I tried repairing the windows installation using the Windows 7 DVD, but it could not find anything.
-I tried booting into safe mode, but it said Windows needs to install first.
Version Numbers & BIOS Setetings:
ThinkStation S10 6423 CTO
Flash EEPROM Revision Level: 2WKT32AUS
[code]....
View 7 Replies
View Related
Dec 28, 2012
I changed my wireless modem password with the comapny the other day and since then, I can not print from my computer. I do see that my printer is set on default.
View 1 Replies
View Related
Nov 20, 2010
i've currently disabled the autoplay to no action for all the options set in the autoplay options in control panel however whenever i connect a external storage like external hd thats split into 3 or 4 partitions i get 4 pop up options on what i want to do & its really annoying. Is there something different i need to edit for external mass storage devices?
View 4 Replies
View Related
Aug 21, 2009
im looking for panasonic kx-p1121 win 7 driver.
its connected to my pc using LPT printer port.
View 2 Replies
View Related
May 21, 2012
plz send me tvs dot matrix printer driver.
View 1 Replies
View Related
Feb 17, 2012
I am currently having problems getting Malwarebytes AntiMalware to function as I want it to and so a possible fix was to uninstall and reinstall. I did this and know CCleaner shows an InnoSetup program that also installed itself as autostart. I've found it is some old type of program installer, but I've never had it, and don't want it.
View 4 Replies
View Related
Dec 14, 2011
Just found out Win 7 SP1 was not auto-installed in a netbook and a home PC today, even though both machines were set up to auto-update. The SP1 was sitting in the Windows update notification. Is this normal?Also after manually installing SP1 (i.e. click OK in Windows update), some old updates started to pop up and asked to be installed. I suppose they were for the SP1. Is this normal?
View 9 Replies
View Related
Feb 9, 2011
I put W7 RTM on a 14G partition, and it's FULL. No personal stuff yet (or ever, so it appears...)
Can some OS files be deleted? And what's with the un-moveable stuff? AERO, and some other processes can go away also here; where do we start? Links
View 1 Replies
View Related
Jul 5, 2011
I have a Fujitus ST4120 and going to use it as my GPS in my jeep for offroading. It has a small drive and I would like to do a clean installation with the bare operating system. What can I trim off the OP system to run my GPS Programs. I want to trim all the non accentuals off the system.
View 4 Replies
View Related
Apr 2, 2012
apparently i tried activating TRIM with the fsutil command but the command prompt says there is no such function... btw i just installed a m4 crucial 128GB into my laptop in ahci mode without TRIm running..
View 8 Replies
View Related
Jul 20, 2011
I'm working with SSDs how can I be sure Trim is working in Windows 7? The computer I'm doing currently I had to flash the Bios from a P5K to P5KR bios so I could enable AHCI. Device manager shows a AHCI controller as well as others. They supplied a Patriot Wildfire for this build, I had suggested a Intel 320 or 510 series to ensure durability and the Intel utilities.
On the ones I built for myself and my brother and in my laptops I used the 320 series and run the Intel utilities so I don't worry about them. This Patriot Wildfire, no utilities, no firmware updates. Samsung's I wouldn't worry, Kingston I wouldn't worry. Since Trim keeps the drive speeds up I'd like to be sure it is working. I've seen conflicting information on the internet.
View 3 Replies
View Related
May 27, 2012
I have trim enabled. Do I have to log off my computer periodically in order to make sure Garbage Collection does it's job?
View 2 Replies
View Related
Sep 30, 2012
I have a 1T SATA system drive and a 1T SATA working drive. I installed a 3T SATA storage drive, and now my system won't boot from the C:. I have to go into the BIOS and boot from there, or use a boot disk. How do I get the system to boot from C: again?
View 3 Replies
View Related
Jan 7, 2013
Okay so, my laptop's system is unable to boot, so I just tried to format it since I have to do that for a very long time, and when it asked me in which partition I want to install windows there was nothing, although when I clicked "Load Driver" I could access the hard disk's files, the hard disk IS listed in the bios normally but windows does not recognize it, I tried using Kaspersky Rescue disk(the only CD I had along with the recovery disk)and when I used the File Manager, the hard disk still didn't show, are there any drivers I have to install?I have burned both fujitsu9that's my laptop) and Seagate's websites and can't find anything, I have searched forums but the only answers were "check if your hd is listen in bios".So, i IS listed in bios but I can't reinstall windows nor access it
View 1 Replies
View Related
Dec 5, 2011
emachine EL1200, AMD Athlon 64, Boxer 61 MB DA061L, 08120-1, 48.3V801.011. 2GB RAM, SATA HDD. Originally Win Vista but upgraded to Win 7 home premium 32 bit which worked ok. Problem - at boot up the following happens: verifying DMI pool data...update success, boot from CD, bootmgr is missing, press ctrl+alt+del to restart. inserted win 7 CD, installation progresses to stage where i get error message: no drives were found.click load driver to provide a mass storage driver for installation.
View 1 Replies
View Related
Oct 14, 2011
Keyboard and mouse drivers unaffected.USB Mass storage device properties messagewith driver check on:"Windows cannot verify the digital signature for the drivers required for this device."with driver check off:Tells me drivers are corrupt or missing.Search show diver where it should be:C:\Windows\System32\drivers\usbstor.sys (also usbfilter.sys).Used the HP Recovery Manager to restore factory setting for USBStor.sys, it indicates it is successful but no changeon reboot, still cannot use flash drives, SD cards, external HDs. Units work find on my laptop.Called HP 4 times, after extensive troubleshooting each time, following their instructions, go to hp.com/go/instant, get screen saying request has been received. Each time tech tells me he cannot find my request.After a while, read 2 hours, told they need to talk to supervisor, will call me back, KISS OF DEATH, never hear from them.
View 2 Replies
View Related
Sep 19, 2012
Every now and then my WiFi stops working, and if I go to dev mgr, the General tab tells me that "No drivers are installed for this device" for device status. On the other tabs, however, I have all the details on the installed driver, and if I ask Windows to update the driver, it tells me that the best driver is already installed. The problem is solved by rebooting, but I find that annoying. I'd like to figure out WHY it does that. I've saved earlier versions of that particular driver from over the last three years, and the problem occurs with all of the drivers. This is a Windows 7 Ultimate 64-bit system. The driver is an Intel driver; the one installed at this moment (it just happened again, and I have not rebooted, since I had a powerline enet outlet handy), and the version of the Intel(R) WiFi Link 5100 AGN is 14.3.1. I have other versions of that driver saved, from 13.2.1.5 to 15.1.1_Ds64. I had reverted to the 14.3.1 because the more recent versions seemed to be worse about the driver disabling itself or whatever it is doing.Coincidentally with this, the event viewer shows that mmc.exe was terminated because it was hanging. I had just run sfc yesterday, and there are no corrupt files that Windows cannot fix, and there weren't even any corrupt files that it DID fix.
View 5 Replies
View Related
Mar 14, 2012
I recently installed a WD 500GB Scorpio Black (Sata II).
I am using a Advent 9117, running Windows 7 32-bit. The drives works fine but was just wondering if i need to install the Intel Rapid Storage Manager/ Intel Matrix Storage Manager program and driver. Will i gain any benefits from doing so? Or is the Windows 7 driver currently installed for the hard-drive fine?
I dont use RAID array, but want to use and enable all the features on the harddrive like AHCI etc. Is this already enabled and used with the current Windows 7 driver?
View 5 Replies
View Related
Dec 15, 2011
how to handle USB removable media inside camera.With camera there is no "Safely remove hardware and eject media" option.When Photo camera is connected, a new camera device is installed and GUI window is opened with option to browse or copy photos. But there is no removable storage devise eject button on notification area. The USB removable Storage devise is also present on File Manager Computer left panel but again, there is no mouse right button eject option as normally with removable storage devices. I have checked in on several computers. How to understand. I don't believe that it's camera specific but Camera is Canon S95.
View 9 Replies
View Related
Sep 18, 2012
i have 3 desktop..two PC is having a win7 32bit and the other one is 64bit..i install the printer LX-300+II(dot matrix) on the 64bit win7...then of course the three desktop is on a network...the 32bit win7 is the admin..then the 64bit win7 and the 32bit admin can print on the dot matrix..but the other 32bit cannot..both of those 3 desktop are shared..workgroup name is same..sharing properties is same for both 32bit..and both 32bit can connect to the printer and can detect..when i tried to print its just qeue and comes with the word "spooling"..but when i tried printing on a laser printer it prints..but on the dot matrix it cannot print...
ways i tried:
1.check the port/ethernet the UTP cables plug out plug in and wait like around 20 secs. then connect again.
2.reinstall the driver on the 32bit that doesnt print.
3.remove device then add printer again.
4.did a windows update.
5.check if same workgroup.
6.check if shared and with same location and can access both 3 desktop.
7.check the permissions.
8.restart the computer.
9.troubleshooting the printer.
10.make sure there's a network connection.
IP address doesn't have because its a USB port and not suported by the OS..3 desktop on a network...two 32bit win7 one win7 64bit.32bit and 64 bit can print on the dot matrix and laser printer but the other 32bit cannot print on the matrix but can print on the laser..when printing its just qeue with spooling..
View 14 Replies
View Related
Oct 4, 2009
I just installed 7 and am trying to get all my stuff up and running. One thing still missing, is a NEC P30 that's connected to my 2003 Server and shared. Windows Update won't find any drivers, how could I go about to use that printer (though it's just an old dot matrix printer, I badly need it.
View 9 Replies
View Related
Dec 22, 2009
I will soon be buying a few new computers for the small business I work for. We are looking to get top-of-the-line computers that will last us another 10 years or so, so I'd like to go with Windows 7 64-bit Professional.
We were at first a bit concerned, though, that the main program we use, DataEase for DOS (yes, I know it's antiquated, lol) wouldn't work, but we've been told it should work fine through a Virtual PC emulated environment running WinXP.
What concerns us now, though, is whether or not we will be able to continue using our old Fujitsu DL4600 dot-matrix printers. We need these printers for printing on three-part paper to get signatures and such.
I'm quite sure there is no 64-bit driver available for these printers, but since we are going to be running XP through Virtual PC - will we be able to print to these printers through that emulated environment?
View 2 Replies
View Related
Dec 31, 2011
i have TVS MSP 250 Champion dot matrix printer.tell me where i get its driver for window7 on laptop ?
View 1 Replies
View Related
Jan 19, 2013
i want driver msp250 champion tvs printer
View 1 Replies
View Related
Sep 26, 2011
I need drivers for Sony Vio on win 7, it's not see mouse and HDD flash.
View 1 Replies
View Related
Sep 26, 2012
I turned on my computer a couple of days ago and found that my entire hard drive had been erased including the operating system. When I tried to reinstall the OS it asked me to load a mass storage driver.
View 2 Replies
View Related
Jan 1, 2013
I just got a brand new computer for christmas, it's a hp compaq dc5850, and it was working fine until now! I tried turning the computer on and it got stuck at the blue hp invent screen, I didn't know what to do, so I finally decided to just try and restore it. When I try to use the windows 7 disc to do this it keeps saying "no drives were found. Click to load driver to provide a mass storage driver for installation".
View 1 Replies
View Related
