How To Setup Multiple (DVI / VGA) Monitors On Windows 7
Apr 19, 2012
I would like to setup 2 monitors on my computer. I know my computer is older but it is very fast and I don't plan on using the monitors on resource hogging stuff
My specs are:
Intel pentium 4 3ghz HT ENABLED
4gb ram
1tb hdd
Nvidia gt 520 1gb
windows 7
My monitors are 2 different inputs / outputs
If I just plugged them both in to the plugin on my gpu would it work and have to adjust stuff? I have never used dual monitors so I don't know. One monitor has a 1600x900 (I plan on this being main monitor)
Other is 1024x768. One of them is dvi and other is vga.
I have attached a second monitor to my laptop which runs Windows 7, however, I need to set different resolutions for different monitors, because the display does not fit to fill the screen on both monitors.
It is also noted that the display is replicated, and I would like to have the effect of having different desktops e.g. being able to use different applications such as debugging code on one monitor on an IDE such as Visual Studio, and, viewing the browser on the other monitor.
Currently it does not seem possible since the behavior seems to be that the same resolution is replicated on both monitors.
I have a new machine that I have installed Windows 7 64bit (build 7100) and am having issues with the system detecting and selecting as my primary display monitors that dont exist.
I am running 2 Gigabyte GTX275s in SLI and have a Samsung 2443BW LCD via a single DVI cable. Nothing is plugged into the other connectors.
I wouldn't usually care if there were other disconnected displays being detected but my problem is it seems to randomly detect a range of monitors at each startup and pick one to be the primary display leaving my monitor blank. The screen will flash 3 or 4 times making the windows sound when you connect new hardware.
I have tried another monitor and get the same result. It is quite frustrating when you have to reboot the system often 3 times before you can get a desktop (an extended one still) so you can get to the display properties and make corrections that dont seem to last after a reboot. I have tried both the 186.18 and 190.15 Nvidia drivers.
Sometimes even into either the change the screen resolution or nvidia control panel will sometimes cause it to refresh all the monitors it detects and i can be left with a blank screen.
I hope I have given enough detail for someone to be able to assist.
I do currency trading from my home, and need to have a full screen dedicated to each currency I trade, each screen/currency running off the same PC at the same time. I know I can attach multiple monitors to my Windows 7 PC, but am not sure how to have the same program running simultaneously on 3 different monitors (that's the only way to get the 3 currencies to show as a full screen and have the ability to submit trade tickets independently based on respective currency). Seems as though the same image will appear on each monitor.Is this at all possible, or will I have to buy 2 additional PCs to put Monitors 2 and 3 on to accomplish this?
I am having a issue setting up 2 monitors. I think maybe I cant run one through my graphic card and my VGA port on my motherboard at the same time.... Right now I am running my monitor through a nvidia 8400 gs but I thought I could run another on my VGA port on the motherboard also.
So I recently found my copy of Battle for Middle Earth 2, and decided to give it a whirl for nostalgia's sake. Only, the moment I get into a game, I'm met with a glaring issue - I cannot scroll across the map in one direction, because my mouse simply moves onto the other monitor.
So, what I have tried, is fiddling with the resolution settings on the game itself - no change. I don't have the option to run it in a window, or move it to my other monitor to see if it persists there. how I might be able to fix this, short of just disabling the other monitor during gameplay?
It seems like a few programs, such as Adobe Photoshop CS4 and Adobe Dreamweaver CS4 (seems to be limited to Adobe), expand past my main monitor, and reach the monitors to the left and right.
This happens when the programs are maximized.
I've included two screenshots of this issue. Notice the additional black border around the main screen (middle one).
Main monitor is 19" connected with DVI Cable Second monitor is 40" lcd connected with HDMI Cable
I want to see my main desktop on 19" monitor and play games movies etc., on 40" lcd and I cant find how to make them independent. I can duplicate or extend them or I can attach up to 6 monitors with the eyefinity technology but 2 independent monitors like in the old times I can't?
How to extend dvi output to multiple hdmi monitors? Have Samsung Series 7 Slate tablet computer running Windows 7 Ultimate 64-bit. Nature of computer prevents swapping out graphics card/module.
Just installed Windows 7. and everytime i start up a game (like left 4 dead)
all screens go black(like when they do when you set a other resolution) and back to normal resolution. when game resolution isn't different from the desktop resolution. and cause i ussually have a series running on one of my other monitors i can't see them cause well desktop thinks it not on its desktop resolution(or for what ever other reason it is that video won't show on second monitor if there is a game up on your main monitor that is not on ur normal desktop resolution).
this doesn't happen with every game though and can't really figure it out. if u need any info, or have no idea what i'm talking about(don't really know how to explain this very wel) post for more details.
3 Viewsonic 22" monitors and one Dell 24 inch monitor all running DVI cables.
I have three of the video cards in the computer to run multiple monitors. Windows 7 has a feature where when you plug in a monitor, it auto detects it and then enables it and sets its proper screen resolution. The problem is that when I plug in more than one monitor, I get inconsistent results.
Here are some examples:
Example 1 that happens: I have two monitors plugged in and I plug in a third monitor. It enables it within Windows 7, but the monitor does not actually turn on. If I restart the computer, somtimes it will stay enabled and boot up with all three monitors on.
sometimes when I reboot it, it again shows all three enabled but only two are actually on. This happens also when I plug a fourth or fifth monitor on. Sometimes two or three monitors will be on whereas one or two others will not be on but will show enabled in display properties.
Example 2 that happens: Sometimes when I plug in a second, third, or fouth monitor, it will actually show an additional monitor as disabled. For example, if I have three monitors plugged in and it shows three monitors enabled (regardless if all three are on and working), and I plug a fourth monitor in, then it enables the fourth monitor, sometimes it turns on, sometimes it doesnt, and it also shows a "generic non-pnp monitor" as number FIVE.
Even though only four displays are plugged in. I've seen this happen even if I plug in a third monitor (shows four, with 3 or number 4 disabled). If I try to enable that FIFTH "ghost" monitor, and click apply, it says "cannot save settings." You can see an example of this as an attachment.
When I plugged in another monitor, it shrunk 2 and there is also a 5 the same size but disabled. Strangely enough, the 2 says the pnp monitor and 5 says the model number of the monitor. However, enabling 5 does not actually enable it and says that it cannot save settings.
I have tried downloading the latest drivers from ATI 9-10 as well as Catalyst Control Center as well as Hydravision from ATI and also Ultramon multiple monitor software. I have tried deleting the ATI 3600 drivers WDDM 1.0 (maybe 1.1) from device manager, only to reboot and then it installed the drivers, reboot again and it brings back all of the whacky settings.
I have a couple of times got all four monitors enabled and all four monitors on where the cursor moves across them properly. EXACTLY what I want to have happen. If I restart it almost always comes back on as EXAMPLE 1 where only two of the four monitors will turn on, but it shows them enabled in display properties, or if all four monitors do come back on, they are not in the same order that I had them in and it actually shows FIVE in display properties.
To make this all even stranger, believe it or not, i've even had it boot and one of the monitors is BLACK & WHITE. What is so strange about this is that the Windows 7 logo when booting, the color Windows 7 logo, is indeed COLOR on that screen, but once it is actually in Windows 7, it is BLACK & WHITE.
If I do a restart, it sometimes comes back in full color. What this means is that there is color while Windows is loading, and then once in Windows one of the monitors is BLACK & WHITE throwing out the possibility of a bad video card.
Has anyone else experienced anything like this? Is there KNOWN issues with Windows 7 and ATI video cards or drivers? How about Windows 7 and Viewsonic or Dell monitors? This is extremely frustrating and looking for some guidance on the subject matter. I believe that the drivers, whether Windows WDDM default or ATI's are simply not correct with Windows 7. I never had this problem with Windows XP.
PLEASE See "win7_monitors.jpg" file to see what I am talking about concerning EXAMPLE 2.
Edit: I need to add that on example 1, where it shows enabled but the monitor does not come on, I have noticed that about 50% of the time when I put the Windows 7 into SLEEP mode, and take it out, the monitor(s) that were off are now on.
So right now I recently got a duo monitor setup. Before I had my 2nd monitor be my TV for movie purposes. Now I have 2 actual monitors 2 19" 1440X900. So far I downloaded a program called DUo Monitor to basically adds a taskbar to my second monitor. Now I want a program to calibrate the brightness and color to be the same on both screens. I tried doing this manually but it's taking quite a bit and I am nowhere near. One is a Gateway other is a Dell.
I am using the system spec as shown in the signature. Both monitors are connected to a single ATI 6870HD. The Dell U2311H is connected to the card via minidisplay-display port while the LG M227WD is connected via the DVI cable. The problematic monitor is the monitor over the display port (Dell). The monitor goes black randomly, sometimes during I play games. Sometimes it goes black more than few seconds, and I get a message on the screen saying power down as there is no reception from the display port.
I have updated the latest drivers, but still this problem persists. A
My office is undergoing a Windows 7 migration and we'll be purchasing ~20 machines. I'd like to optimize each machine by turning off various services and creating a global standard user profile. We run a workgroup, is there a way I can copy the service.msc mods and the global user profile from a single machine and apply those changes to all machines?
I have a AMD Radeon HD 6300 series adapter, running windows 7 x64.I have a dual monitor setup,the same monitor on each port an Acer S230hl. One port is an HDMI the other is a VGA. the issue i have is that when i have a worksheet open i can see the gridlines to the cells on the HDMI connected monitor, if i move the sheet over to the vga monitor the gridlines are so light i cannot make out the different cells. it looks like one clean sheet of white paper.i tried different contrast and brightness settings and no luck.
I currently have a dual screen setup, the primary a computer monitor and the secondary an HDTV hooked up via HDMI cable. Accordingly I have 2 sound setups; a set of speakers at my desk and the other is the TV's speakers.
The problem is most programs have no option to choose the audio playback device. Everything goes to the default in Windows, so I have to manually change it every time to either the TV or the speakers. I only really use the HDTV to watch videos and want only the sound from that specific program to play on the TV, and everything else on my desk speakers.
I had a workaround to this in Vista. By setting the default audio device to the HDTV Windows would automatically switch the audio output to the speakers when disabling the secondary monitor which could be done easily with UltraMon. Windows 7 audio playback doesn't seem to detect this change so I'm wondering if anyone knows of a solution or workaround.
We have a small business that consists of 5 owners. One owner does most of the work and has a Desktop set up in a home office. They do most of the document related work. This person needs physical control of the computer for most of the day. The other four either live in different locations. They need all the information that the main computer has throughout the day. Documents that change, New documents, and the ability to change anything in the documents and save them. The way its setup now is a remote login. This is extremely inconvenient since the main computer is basically hijacked when someone remote log ins. Each computer is obviously on a different network, so local networking wont work.
Is there a way that the main computer can be on, being worked on by the main person, but still be accessed by the other people at the same, or different, times to get the updates and new documents? Can we do this with what we have, or is there another way to do it?
We have thought of various things, like severs, remote log in programs, etc. But nothing really works the way we need. The closest one we found was an auto sync program. But it requires everyone to have all the files on their computer. This is slightly inconvenient because theres thousands of documents and things that everyone would have to load when one person may need 1-200, and the other needs 200-400.
I am in the process of putting (5) 3TB HDD's into my computer (Windows 7 Home Premium 64 bit) to rip my Blu-ray collection to for playback in my home theater room via a Popcorn Hour player. Each drive is independent and I will be systematically filling one drive before going onto the next.The problem is that the Popcorn Hour players communicate with the PC by specifying one folder via SMB that contains all of my media. Since I am doing independent drives, there will be one master folder on each drive containing all of the media for that said drive. Meaning, in terms of the Popcorn Hour/SMB setup, there are five folders I need it to *see* and catalog.
We have three medical clinics and the front desk staff float from clinic to clinic depending on their schedule. I only started here a few months ago and I am working on upgrading their Dell xp systems to Windows 7 systems.The problem begins to crop up when say a user named Sally will come in and sit down at this system for the first time.. Well, she needs to login, click on outlook icon, let it find her exchange PST and copy settings to her user profile, then she launches the application for the scanner that she uses to scan in ID's and insurance cards for every patient coming in.. The scanner is set to default settings and needs to be tweaked on color depth and double sided, etc.. Then after that, she needs to launch her Medical EMR application.. and then choose various options in the citrix client, ..TL;DR - Each user needs to spend 20 minutes resetting the defaults at this updated system. Well this is fine except, I am planning on updating 2 front desk systems at each clinic, the user Sally will need to do all these things EACH time she finds herself sitting down at a system I just swapped out the previous evening.My thought is this, put a single system down in one clinic and let it sit a week giving most of the float users a chance to work on it for a day, setting all of their preferences etc.Once I get a bunch of them with user profiles on the local drive, grab an image of that drive and just deploy that to each system I roll out..Couple issues I am running into:First would be that I would have to register each Windows 7 copy with a new serial, which I have The next issue is, we have a mis-mash of Dell optiplex systems. 330's - 380's even a couple 320's..
one of the netbooks was plugged in to initially power it up, but then hard-shut-down before Windows could run through its initial setup.Now when I boot up the netbook, and it attempts to go through the initial windows setup "Setup is starting services", and then throws an error message: The computer restarted unexpectedly or encountered an unexpected error. Windows installation cannot proceed. To install Windows, click "OK" to restart the computer, and then restart the installation.I restart, and the cycle continues. This happens whether I try to boot normally or in safe modeI've got no CD-drive attached to it, so I'm not sure what I can do to break this error cycle.
I am trying to get my wife's new computer up and running without any BSOD or program failures. Note that the system was not initially set up to capture the dmp files so all the earliest ones are missing. I presented the initial problems to the original seller who recommended sticking with MSE and uninstalling Norton 360 and I did that. Another forum suggested that Virtual Memory was the problem and I disabled and restored VM. Still having multiple crashes and I am hoping that I can get real help here. I do note that all the crashes have ntoskrnl.exe in the driver stack although sometimes alone and sometimes with other drivers.[CODE]
I have been getting a fairly random blue screens and I cannot pin point it myself. I know a bit about diagnosing and repairing issues but this one is just a pain in my butt. I am uploading the dump files and I hope someone can give me a hand I am running a sfc scan right now to test for any problems too. Also got this off the TSG SysInfo Program.
Tech Support Guy System Info Utility version 1.0.0.2 OS Version: Microsoft Windows 7 Home Premium, Service Pack 1, 64 bit Processor: AMD Athlon(tm) II X3 445 Processor, AMD64 Family 16 Model 5 Stepping 3 Processor Count: 3 RAM: 8191 Mb Graphics Card: NVIDIA GeForce 9600 GT, 512 Mb Hard Drives: C: Total - 476837 MB, Free - 246483 MB; Motherboard: BIOSTAR Group, N68S3B Antivirus: Norton Security Suite, Updated and Enabled
When I try to install some programs and drivers i get error: 'Setup will only run in administrator mode. setup is aborting.'. I only have one account which has administrator rights. I have already tried to enable and disable UAC, booting in safe mode, run as administrator, enabling original administrator account, adding permissions, taking ownership, changing compability mode and other but nothig is solving my problem. I'm running windows 7 x64 build 7000.
I'm having a bit of trouble trying to get two monitors, a small 1024x768 LCD, and a 46" 1920x1080 TV, to display the same wallpaper at different resolutions. My graphics card is older, a Nvidia Quadro FX 1700, but it is perfectly capable of driving both displays at the same time. It's a minor annoyance, but I'd like to get it working if it's possible.
I am trying to set up 2 external monitors to my Dell e6410 laptop.
Specs:
Quote: Operating System MS Windows 7 64-bit CPU Intel Core i7 @ 2.67GHz54 �C Arrandale 32nm Technology RAM 4.0GB
[code]....
IDT High Definition Audio CODEC I have my laptop in a docking station that has 2 DVI-D Male/Male connections. I have a DVI-D cable running from each to an LG monitor. When I go to the display settings, I can get one of the monitors to extend out from my laptop, but I cant get it to go to the third one.
Whenver I maximize a window it goes across all three screens, now that is okay for video games but not so much for the internet or other programs. Whenever I open a program it is opened very small and I have to manually adjust to windows to each screen, and it kind of gets annoying.So is there a way that I can change a setting or something that when I maximize my window it will only maximize on the screen that I have the window open on?I am running Windows 7 btw.