Windows 7 Starter Getting Error On Initial Setup; Locked In Setup Loop?

Oct 5, 2011

one of the netbooks was plugged in to initially power it up, but then hard-shut-down before Windows could run through its initial setup.Now when I boot up the netbook, and it attempts to go through the initial windows setup "Setup is starting services", and then throws an error message: The computer restarted unexpectedly or encountered an unexpected error. Windows installation cannot proceed. To install Windows, click "OK" to restart the computer, and then restart the installation.I restart, and the cycle continues. This happens whether I try to boot normally or in safe modeI've got no CD-drive attached to it, so I'm not sure what I can do to break this error cycle.

View 6 Replies


ADVERTISEMENT

Crash On Initial Setup - Windows 7 X64?

May 23, 2010

Set-up isn't finishing as the install will crash BSOD 0x0116 with atikmag.sys causing the problem.(**Note, there is NO Minidump found after this crash - I"ve lookedlooked.. and looked... so I took a digital photo of the BSOD screen in the moments it flashed)I can't complete the install using safe mode, but in safe mode I can get to the part where set-up is trying to finish.So, how can I force the install to bypass graphics card driver install and install a standard SVGA driver until I can get the thing to finish set-up??

View 6 Replies View Related

Run The Initial Setup Again?

Apr 13, 2011

Remember when you installed Windows 7, there was that one setup thing that asked you for the time, your username, and password?Ok so my friend wanted me to upgrade his HP laptop to Windows 7, since he originally had the you-know-is-junk version of windows (Vista).I was able to install all of the software, but what I want to know is if there's a way to run that configuration setup thing again.

View 1 Replies View Related

Windows 7 Upgrade Failure - No Automatic Rollback Continuous Loop For Setup?

May 11, 2011

Went through the recommendations for upgrading to windows 7 as per instructions on CD. Anything incompatible was removed, uninstalled prior to set-up. On first run through set-up failed, BUT, this was easily rolled back. Not so easy the second time round where there was no option to roll back. On rebooting I could not access any of the software programmes on the pc. Instead I was taken straight to the command screen:

X:$WINDOWS.~BTWindowssystem32>

The only access I have to all my directories is via this screen.I did attempt to a system restore but was asked to identify which system to restore and was unable to do that as I am not very technical.I can, by hitting F8 get to the advanced boot menu, but none of the options listed there function. When selected they take me back to the command screen. If I exit the command screen the pc reboots.Is there any way I can get to restore my previous o/s Vista and then hopefully I can get to do a clean install of windows 7? it currently looks like I am running two opeating systems and windows.

View 3 Replies View Related

HomeGroup Setup - Documents / Pictures Folders Visible But Locked

Jul 4, 2011

I have two pc's in my home. One running windows 7 32 BIT, and one running Win 7 64 bit. I created a home group on the laptop, as I want to grab some files from the laptop and bring over to the Desktop unit (the desktop unit is the one running 64 BIT win 7). Both machines have different names and the clock is set with the right time. When I create the home group on my Laptop, and select files that I want to share, the basic libraries ARE viewable on the Desktop machine.

I can see Documents, Picture folders, but I cannot open them! I can also change the password on the Laptop, and then PC will be able to enter the correct password to join the homegroup, so I know they can see each other. But again, not able to open the folders. If I go on my Laptop computer and "right click" on a folder, and then go to "share with"... the default is set to "nobody" with a lock icon next to it. If I select "Homegroup" it does not change! It stays locked with "nobody"?

View 1 Replies View Related

Setup Starting Services Loop - No Repair Or Installation Disk

Feb 8, 2012

My laptop Specs below:
Acer Aspire 5742
Intel i5-480M
6GB DDR3
Intel Graphics

It started when I needed to take the computer back to factory default with a fresh install. It was going back to Acer to have the charger point fixed (charger socket had become loose but still charged when it was held in). I used the control panel interface to reinstall windows, all was going well until the laptop power died, I restarted the laptop and the screen displayed:

"Setup is starting Services" a pop up box then appeared with "The computer restarted unexpectedly or encountered an unexpected error. Windows installation cannot proceed. To install Windows, click "OK" to restart the computer and then restart installation."

I have searched around the net and found a few guides but most require a repair disc or Installation disk. I have neither. Is there any way of starting the install again? For example from Command Prompt?

View 4 Replies View Related

Acer Aspire One D255 Setup Is Starting Services Loop

Jan 20, 2013

"On the same error screen press SHIFT+F10 and it will open up a black Window. (a command prompt window) 2) In the black windows type the word "regedit"(without the inverted commas and hit enter. That will open the registry editor. In the Registry Editor.. Browse to.... HKLocal machine/SYSTEM/SETUP/STATUS/ChildCompletion, and after highliting childcompletion,on the right hand side check for setup.exe. if the value is 1 change it to 3.(by double clicking on setup.exe and changing the value shown in the box). Then close the registry editor and then also close the black window. Then click on OK for the error and the computer will restart and the installation may complete. just try it and let me know if it worked."

I tried the above and rebooted, I still get the dreaded "Setup is starting services" loop

View 1 Replies View Related

Windows Auto Boot Into Windows Setup Loop

Mar 28, 2012

Yesterday I've reinstalled windows on my laptop, the only 'problem' was that on booting, the system lets you choose between windows 7 and windows xp setup. Windows xp setup was the default choice. Now when I was done installing windows 7, I wanted to get rid of the win xp setup boot option. In my control panel, I deselected the option for the boot selection screen where you can set the time. Now my pc got stuck in some kind of boot loop where it only boots into win xp setup. I don't know how to resolve this because the only option I have on booting is entering the bios... when I press f12 it should go to boot options, but it just goes automaticly to win xp setup.

View 1 Replies View Related

Setup Will Only Run In Administrator Mode - Setup Is Aborting

Jan 16, 2009

When I try to install some programs and drivers i get error: 'Setup will only run in administrator mode. setup is aborting.'. I only have one account which has administrator rights. I have already tried to enable and disable UAC, booting in safe mode, run as administrator, enabling original administrator account, adding permissions, taking ownership, changing compability mode and other but nothig is solving my problem. I'm running windows 7 x64 build 7000.

View 4 Replies View Related

Getting Windows 7 Installation Setup.exe Error

Jan 13, 2013

I m reinstalling window 7 on my new laptop ..previously it got 000000f4 error blue screen appers and it restarts all the time so i decide to reinstalll it..so when i reinstall it setup was working fine but at the end it got setup.exe error ..i thought may be cd is corrupt ..so i bought new cd now when inset a cd it appera press any key to boot from cd han i presss any key than window is loading file after that window is starting up appers than it is frozen their why .

View 1 Replies View Related

Get The Error Code 0xc0000098 After Trying To Start Windows Setup

Feb 2, 2013

I get the error code 0xc0000098 after trying to start windows setup from windows boot manager.

View 4 Replies View Related

Stop Error 0x1E Caused By Nvlddmkm.sys During Windows 7 RC Setup

Jun 1, 2009

Workaround for nVidia display driver issue
Motherboard: ASUS M2NPV-VM
BIOS Version: 0504
GPU: nVidia GeForce 6150
in Windows 7 RC
Symptoms: Stop Error 0x0000001E caused by nvlddmkm.sys during Windows 7 RC setup

Details:Perform these steps on another computer:

1) Download a current driver from nvidia.

2) Extract nvlddmkm.sy_ using WinRAR.

3) Expand nvlddmkm.sy_ from windows command prompt

cd [path_to_nvlddmkm.sy_]
expand -r nvlddmkm.sy_ nvlddmkm.sys

4) Put a copy of the new nvlddmkm.sys file on a flash drive

Restart Windows 7 Setup and perform these steps:

1) During the "Expanding files" step, press Shift-F10 to open a command prompt

2) Replace the nvlddmkm.sys file located at C:WindowsSystem32DriverStoreFileRepositoryv_lh.inf_amd64_neutral_4f38d443efdd0a70 with the new one from the flash drive. Wait for setup to create the file before you replace it -- seems to occur when the progress meter reaches about 70%.

3) Let the install process finish,

View 9 Replies View Related

Install Windows 7 And Error: Setup Was Unable To Create New Partition

Jan 16, 2013

I tried to dual boot Fedora 18 with my Windows 7. They are on two different hard drives. Fedora 18 worked but I was unable to boot up Windows 7. Frustrated, I decided to just delete everything from all the hard drives and try to do a clean install of Windows 7 using the USB-DVD Windows tool to make a USB Windows 7 installer. I then got the following error when trying to install Windows onto my hard drive:

"Setup was unable to create a new system partition or locate an existing system partition. See the Setup log files for more information"

I tried unplugging the other hard drives and got the same error. I also went to the command prompt and used Diskpart and did clean all. Still the error shows up. Something that might be useful is that when I did disk list in the command prompt it showed my hard drive but with 0 free space. Not sure if this is useful but the drive I want Windows 7 on is a solid state drive but the one I had Fedora on is a normal hard drive and I had an extra harddrive that I used for storage that is a normal hard drive as well.

View 10 Replies View Related

Inatall Office 2010 On Windows 7 - Get The Error : Setup Cannot Find ?

Jan 23, 2013

I'm trying to inatall Office 2010 on Windows 7 and I get the following error :

Setup cannot find InfoPath.en-usInflR.cab. Browse to a valid installation source and then click on OK.

View 2 Replies View Related

Age Of Empires 3 Setup Error

Oct 28, 2011

When I downloaded the game I could run the setup and it worked but I had to install the game in 64 bit.So i deleted the installed part and returned to downlaoded to try again but this time.

View 1 Replies View Related

Setup Error 0xE0000100

May 19, 2009

When I run the windows 7 disk at the boot up and the menu pops up i try to choose clean install but i get an error that says "Windows installation encountered an unexpected error. Verify that the installation sources are accessible, and restart the installation. Error code: 0xE0000100"

View 6 Replies View Related

0x80070057 Error During Setup

Nov 1, 2010

I'm redoing a customer's machine and right after selecting the partition to install on I get a 0x80070057 error. I have reloaded bios defaults, low leveled the drive and am only trying to use a single large partition.

specs are

gigabyte ga-g31m-es2l mb
4 gb gskill ram
500 gb WD hdd

View 2 Replies View Related

Extender Setup Configuration Error

Dec 3, 2009

After entering the 8 digit code on my Windows 7 Ultimate PC in the extender setup, I get the "Configuration Error" "An error was encountered while configuring your computer for use with this Extender.".

Happens every time the same way. Each failed attempted causes two event log entries below. Interestingly, immediately after the failed attempt - the "Media Center Extender Service" service gets disabled. It is running under the "Local Service" account. I can set it to "automatic start", and then re-start the service, but as soon as I go through the Extender Setup, and it fails, the service is disabled again, with the two event log entries..

View 4 Replies View Related

Press F1 To Resume F10 To Setup Error

Dec 12, 2011

when i switch on my pc A window comes and shows f1 to resume .why is my pc showing that

View 1 Replies View Related

Random BSODs With Different Error Messages After New Setup

Mar 15, 2011

I recently upgraded my setup with an Asus M4A78LT-M mobo, Athlon II X4 640 processor and TakeMS 2x2GB 1333MHz DDR3 memory. After installing the parts I tried to boot to Windows but it always resulted in the same BSOD so I reinstalled my system. After installing Windows for the first time I had some problems downloading updates and I got a couple of BSOD's during the update process. I then thought the installation was faulty and reinstalled it again from a different DVD. Once again I got two BSOD's during the Windows update but after all updates and drivers had been installed the problems vanished and three days pass without any problems.

Today I was watching a movie from my computer and suddenly the computer made a BSOD. I rebooted, opened Event Viewer and got a BSOD again. I ran memtest for 6 hours and it passed 5 times without errors. I had set the memory timings to 9-9-9-24 and memory voltage to 1.5 after the first BSOD's a few days back to ensure they were running at the proper settings. Apparently it didn't work. The new processor consumes 25W more than my previous E5200 so maybe my 500W power can't keep up with it sometimes?

View 9 Replies View Related

Error: Setup Was Unable To Create A New System Partition

May 4, 2009

When I try and install Windows 7 64-bit on my hard drives I get the fallowing error.

Setup was unable to create a new system partition or locate an existing system partition. See the Setup log files for more information.

Its doing this with vista now.

View 9 Replies View Related

Error Code 6 - Setup Was Unable To Complete The Installation

Nov 1, 2009

i recently installed windows 7.. when i installed VIA drivers for graphics it didn't get installed properly... i had the message "setup was unable to complete the installation (error code-6) ".. so i was asked to upgrade my BIOS... i downloaded it and installed it... when i ran the update, the system just hanged up and nothing happened for hours,..

so i had to restart the system and went to BIOS settings and clicked load optimized settings,,,.. from then onwards my OS is booting until the windows startup screen appears and just hangs..it's not booting to the users login... but it logs in at times... i dont have any restore points too..what to do?

View 11 Replies View Related

Setup Cannot Find Or Create A System Partition Error

Mar 27, 2011

After 8 long years I've finally upgraded my wheezy old pc, and now am drooling to play with this beastly new machine I've just assembled. My system specs should be in my sig below.But after 12 long hours of trying to install windows 7 pro, I'm more kinds of frustrated than there are words for.As in the topic title, I'm up against the "setup cannot find or create a system partition" error. My machine has a single 2 TB Hitachi Sata 3 hard drive, so there is no raid to muck things up, which seems to have been the primary cause of everyone elses troubles with this error. Using my old rig, I partitioned the new drive and transferred all the data from the old drives, leaving the first 75 GB partition empty and waiting for windows 7.

Then "the troubles" began. Research ensued.First thing I tried was to load updated sata 3 drivers from the mobo install disk. No help.Then I tried downloading the latest drivers from Asus and loading them from a flash drive during installation. No dice.Then I tried changing bios settings from Sata to IDE. No dice.Tried all of the above again with minor tweaks. Using the setup tools, I deleted that first partition and tried to make it again but setup gives me the title error.Well, of course I need that partition back so after some more research, I downloaded gparted, booted it up, but the video output is messed up and impossible to read.Then I slept for 6 hours. I woke up, tenacious and desperate, and figured I'd try diskpart (well above my paygrade) to make the first partition active and/or primary. Diskpart won't allow it? I disassembled my new system, plonked the old system back into the case, booted up into winxp off the old hard drive and with Easus partition manager and tried the same thing as with diskpart, but with the same results. No dice.Then, clearly somewhat crazy at this point, I put the new machine back in the case and tried ALL OF THE ABOVE AGAIN. No dice.Upon boot, POST sees the hard drive, but its not detected in bios. I don't know whether this is a hard drive problem, a mobo problem, a configuration problem, or completely normal for my gear. In any case, windows setup lists all the partitions.

View 5 Replies View Related

Dual Boot Setup - Unable To Identify Network Error

Mar 3, 2012

Just today I decided to download the Windows 8 consumer preview and setup my PC to dual boot with it.I am running Windows 7 home premium 64bit and the 64 bit windows 8 on my other partition. After setting up a separate partition on my hard drive and loading windows8 to this partition, I was all up and running. I had no problems setting up or running windows 8, the problem came when I booted back to windows 7 for the first time. When I booted into windows 7, I was getting the "unable to identify network" error, and no network connectivity.

First thing I tried was simply disable/enabling my network adapter thinking it was just some hiccup. No luck there. Next I pulled the power from my router, and let it completely reboot. Still no luck. I then shut down my pc and booted back into windows 8 and sure enough I am able to get internet connectivity when I am running windows 8. This got me to thinking that when I loaded windows 8 there may be some new drivers installed for my network card that are somehow causing issues when I load into windows 7 again. Not sure how this is possible.

I was under the understanding that when I loaded Win8 to the separate partition that it would keep all it's drivers and settings there and not effect anything when I was loaded back on windows 7 (This logic could be completely wrong, I don't know). So I rebooted and loaded back into windows 7, went into device manager and uninstalled both network adapters and drivers, and rebooted into windows 7 again so it could re-discover and setup the network cards with default windows 7 drivers. This did not work either and I am still getting the same error.

View 5 Replies View Related

Install Error Setup Was Unable To Create A New System Partition

Nov 5, 2011

I am having a problem with doing a fresh install of Windows 7. It is on a Dell Inspiron 1546 with a 150 GB hard drive. There was an original install but the computer was having issues as some files were corrupted. I used the Windows 7 disc to format the hard drive and booted from CD after restarting.

However when I try to install the new Windows 7 it sits at the part where it says: Expanding files. Then after a while an error pops up that says: Setup was unable to create a new system partition or locate an existing system partition. See the Setup log files for more information

View 3 Replies View Related

Setup Was Unable To Create A New System Partition / Installation Error

Dec 28, 2011

I have my HP Laptop which came with Windows Vista as the OS. I want to upgrade to Windows 7 so I bought Windows 7 from my local store.I entered the disc and did boot from CD. It reached to the page where it shows the disk partition. I deleted the partitions and created new one. However, whenever I create the partition, it creates a primary one and gives me saying Setup was unable to create a new system partition or locate an existing system partition.The stupidity that I did was deleted the partition which had the Recovery Drive in it. So, now I am stuck and not able to install Vista as well as Windows 7. I am not able to boot Windows as there is no OS in my laptop now.

View 9 Replies View Related

System Fails To Boot Setup DVD - STOP ERROR 0x000000A5

Feb 26, 2010

run windows 7 on an old laptop, an hp pavilion zt1250 (1ghz, 1gb ram, 20gb hdd, dvd/cd, external wlan, xga screen, that sort of old). it isn't like a serious installation, it is more like a "post on Internet to a "windows 7 running on a nine year old laptop" or "wow your friends with your old computer running a newer os than their new one (possibly)"", and because it looks pretty darn cool. anyway, i pop in the install dvd and we get past the gray progress bar and onto "starting windows", until all of the sudden out of nowhere, just a second before the cutesy windows logo animation appears, i am instantly greeted with a blue screen saying nothing more than:

stop: 0x000000a5 (0x0001000b, 0x50434146, 0xffd0ac0, 0x00000000)

it does it on all install discs that i've tried, and it gives me the same error consistently every time. i even tried starting the installer within xp, and that starts okay, but after the first reboot where it boots the partially installed os from the hard drive, it does the same thing before it can continue. everything that is not essential has been unplugged, tried removing ram modules, on battery or plugged in, checked the extremely simple bios settings menu (you can change like three things, none of which pertain to the situation), and most other items that could possibly be covered here. this leads me to the conclusion, that since it my disc is fine and my hardware is fine (did a bios update), that the installation disc must be first modified in some way, perhaps to skip a certain unnecessary check?

View 9 Replies View Related

Unable To Execute File In Temporary Directory Setup Aborted Error 5

Dec 12, 2012

i just downloaded dishonored pc game but it comes that unable to execute file in temporary directory setup aborted error 5

View 2 Replies View Related

Setup Can't Continue, Restart The Computer And Restart Setup

Oct 28, 2009

I am trying to upgrade Vista to Windows7 Home Premium and I got this message after the installer copied ~2GB of files on my PC:

"setup can't continue. restart the computer and restart setup. when prompted try getting the latest updates."

I restarted the PC and restarted the setup and I got the same message. I updated the Mother Board Bios and restarted the setup I got the same message. I have tried both options (get update and no update during the setup). And it didn't work.

I do not want to do custom install (fresh install) on my computer.

View 1 Replies View Related

Windows 7 Startup Error Failure To Initial Environment (MFC)?

May 18, 2012

When I start Windows 7 about 30 seconds after the login, I see an error message popping up that says: "Failed to initial environment". In the task bar I see the an icon that writes MFC, which is the program that gives the error message. I looked in my task manager under processes if I see MFC, but there is nothing like this. I am using Windows 7 64 bit.Does anyone have an idea what that would be?Here are 3 screen shots, which show the error and all processes running in my task manager.

View 5 Replies View Related

Windows 7 Startup Error Failure To Initial Environment (MFC)

May 18, 2012

When I start Windows 7 about 30 seconds after the login, I see an error message popping up that says: "Failed to initial environment". In the task bar I see the an icon that writes MFC, which is the program that gives the error message. I looked in my task manager under processes if I see MFC, but there is nothing like this. I am using Windows 7 64 bit.

Here are 3 screen shots, which show the error and all processes running in my task manager. [URL]

View 2 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved