ECS H67H2-M black
Intel i3-2100
4GB (2x2GB)DDR3 1333MHz Twinmos 9-9-9-24
2TB Samsung HD204UI HDD - OS, media and files
Thermaltake Toughpower 600W PSU
Lite-on DVD+/-RW
Windows 7 x64 Ultimate
I'm having a whole store of BSOD's but the really bugger is the part where i can't shutdpwn the rig completely. If i press shutdown via start in win7 the rig shuts down fine and dandy...but give it 3 secs and it powerback up again..
I've noticed many users are having this or a similar problem w/ shutting down or computer won't turn off completely, then restarts by itself! It has to be a hardware problem, but I haven't been able to find a definate solution to this prob which is plaguing my new computer and another one.
First let me say, I have purchased a copy of Win 7 Ultimate upgrade from my university. I am NOT, repeat NOT, asking about pirated software. I am asking about a copy of Windows Ultimate 7 Upgrade.I have had issues recently with my system. After a whole lot of BSODs and reinstallations, I have isolated the problem and subsequently relegated that computer to being a home theater PC. During the setup, I was installing Windows. When I put in the key, it rejected it. I input it about 10 times, each time verifying it, and it kept rejecting it. I have installed this copy several times before, and had no problems previously. This is a fresh install, and the installation went smoothly up until that point. I did let it sit for about an hour during the installation. It sat at the point where you put in the username/password and then the windows key.
I built a HTPC with a video card that does DVI and hdmi. The motherboard has a VGA.
But I also need either: s-video or composite What should I do? I don't want to like "downgrade" the video card and just use an old one for everything. Can I run them both? Like switch back and forth? "Simultaneous" is not required.
Also, I would already be using the PCIE 2.0x16 for the video card. I have PCIEx1 and PCI slots open. EDIT: I found this... [URL]
Would this work in letting me switch between the onboard video and the video card?
Basically I know virtually NOTHING about video cards. Last time I got one it refused to work in my computer (an Old Dell).Basically I want to be able to decode 1080p (and do re-encoding, not necessarily 1080p) without my computer bogging down. And I want to stream to my Xbox with subtitles, which my G620 simply CANNOT do (as it requires burning in subtitles on the fly before streaming it to the xbox).I don't want a super expensive GPU, but it needs to be low-profile to fit my case (info in hardware description)
I *think* I've managed to figure out that an AMD Radeon HD 6850/70 will work for playing 3D Blu-Rays with TotalMedia Theatre 5, onto a Samsung 6000 series 3D TV with Active Shutter glasses over HDMI 1.4a.
I am currently building an htpc that will be used solely for watching movies from my hard drive, blu ray discs, and online streaming. I am trying to find an hd media player that is very light and simple. I have tried KMPlayer but it seemed to open fairly slow on my current computer, which isn't slow. I have also tried splash lite which I really like, but on some of the movie files it does not play sound, so no go there. Any other suggestions about what software would be the best? It doesn't need to be powerful because I will just be watching movies, I mostly want it to open fast and and have a small footprint.
got myself a little pc that im using as a HTPC... I initially purchased a DisplayPort to HDMI cable to connect the htpc to the pioneer amp and then to the tv the video signal works perfectly, but i couldn't get any sound coming through, so then i tried adding a audio jack from the htpc to the amp, still no luck...i have test the sound from the htpc and the sound come out from there, but when connect to either the amp or tv, via the audio jack it doesnt work HP Compaq 8200 Elite Ultra-slim PC specifications - HP Small & Medium Business products?
Some time ago i put together a HTPC with a Asrock A75M-HVS mtherboard (VIA VT1705 Audio Codec) hooked up to my tv with HDMI(sound+video), installed windows and installed on the drivers from Asrocks website.Today i was thinking that I had probably installed the audio drivers over the windows drivers and i wanted to make sure i had the latests drivers from VIA, i was looking around how i could stop windows from installing audio drivers, i found a method using gpedit.msc wich seemed to work, it blocked windows from installing its own driver.So I downloaded the latest driver from VIA website (this was a newer version then from asrock's website). I think it installed correctly but the only thing that showed under playback devices was "Speakers", the digital hdmi output had dissapeared.I tought this was a problem with the driver so i download the one from Asrock thinking this one has to work, but the same problem.This had taken several hours of messing around so i tought screw it, ill take the windows drivers, so I let windows install and it seems to work and i got my sound back, under playback devices there are now 2 options again "speakers" and "digital audio hdmi". I get sound using the digital audio output, but only stereo, when i click the configure option it doesnt let me pick 5.1.I dont really care anymore what driver I have, I would just like to have my 5.1 back,
I built a tiny yet powerful HTPC with the new sandybridge Intel i3 CPU. is there some kind of software that will turn off the spinning HD when it is not needed and only turn on if say a tv recording is scheduled for a certain time, record the show, and then turn the hd off again. it runs windows 7 64 bit, 8 gigs of ram, 2tb hd, blu ray burner.
I tried searching first but I seem to have trouble finding the proper terms to narrow the search enough... So I just post this.I put together a HTPC for 24/7 usage (windows media center and iMON remote control, spotify, PowerDVD for Blu-Ray movies). Minimal amount of additional software installed. The problem is it locks up often. The whole Windows 7 goes fully unresponsive (all you can do is power off -> on). It rarely stays responsive for 48 hours. No crash dump is generated. The event log shows nothing special, mainly two error items, one related with errors on Microsoft Security Essentials and the other is Circular Kernel Context Logger session failing to start.The main question is: what is there to do, is there a program that could monitor which other program seems to halt the system? I'd hate to go through eliminating each and every software/hardware component... The second question is: just in case, does anything below ring any bells what might cause the problem?
Currently I'm using the Logitech K400 wireless keyboard with a built in trackpad, but for my next system build I won't be using it because of finicky reception. I'm currently looking for alternatives, and I want your advice. Currently I'm considering one of these: IOGEAR GKM561R Black 2.4GHz Wireless HTPC Multimedia Keyboard with Laser Trackball and Scroll Wheel IOGEAR GKM561R Black 2.4GHz Wireless HTPC Multimedia Keyboard with Laser Trackball and Scroll Wheel. (They seem to be identical but Newegg lists them separately).
I am using a very cheap receiver from Amazon with the PC Remote Control drivers provided by Eventghost. From my other readings the best way to identify the remote is the presence of [URL] in the GUID. My problem is this. When I put the computer to sleep and begin watching another source, the commands from the television remote are detected by the IR receiver and wake the PC. Is there any way to select which signals would wake the computer?I currently have the power management settings configured to not allow the IR receiver to wake the computer and use the power button to wake it?
I'm thinking about building a new main PC and hooking my current one up to my receiver and plasma tv (50" Pioneer Kuro 720p). If I put a BluRay player in the new PC, will I be able to display it on the tv over the network or does the BluRay player need to be in the HTPC? My current machine's mobo is IDE, not SATA, so I assume that would limit my options on a BD drive.
I am experiencing a unique issue with my WMC HTPC box. Anytime I watch content from either WMC7 or WMP7 I get audio and video stuttering every minute. Sometimes, the stuttering will cause the box to freeze up, forcing a restart. At no time do I receive memory warnings prior to or after each event. I've tried restarting the computer in the hopes of clearing the RAM, clearing the Temp Files, and running ChkDsk (at the time of this posting, the process has taken over 1 hour to complete - not sure if this is normal). I also installed Process Explorer to see if the issue was memory related. While it appears that WMC is hogging up to 3/4 of my RAM at some points, usage is mostly confined between 1.3-1.7 GB.
The spikes occur regardless of the RAM usage but not when WMC is running idle (meaning ON but not displaying content other than the main menu). Process Explorer appears to show that the issue is possibly related to SVCHOST - when I place my mouse over each spike, it displays SVCHOST but not the programs which that particular version of HOST is running. I am running WMC7 64-bit, with two 500GB drives (one mirrored), a third drive (2TB internal) for video and music, 4GB of RAM, an Intel i3, a Hauppauge 1850 Dual Tuner, and a ASUS P7H55-M PRO motherboard. I will update with ChkDsk info when it finishes.
I've recently started to experience a BSOD problem I cannot quite put my finger on. It does not save a log, even though I have it set to save in /Minidump. I have not changed or added any hardware, or software. I completely wiped Windows and started over from scratch, using the most up to date drivers. However they're still occurring, I've restored my BIOS settings to all default settings. I am thinking it was a Hard drive issues, I've ran CHKDSK all both drives - I know my Windows drive was clean, I was not around to see the completion of of my slave drive - I was running CHKDSK via Safemode and came back to a BSOD. I've attached a administrator Eventlog, but am unable to make much sense of it.
NTFS.SYS - Address FFFFF88001338890 base at FFFFF880012450000, Datestamp 4ce792f9 I've ran Memory test already, no errors where found. The next step I am going to try is too unplug my Slave drive and see what happens without it. I've already re-seated both drives and memory sticks.
I have just set up an HTPC and would like to partition the drive so that I have a small drive of, say 32gb for OS and the rest for storage. According to the system (after fist shrink) the c drive is 204gb free of 295gb, but I can't shrink it further. I've done a disc clean up and emptied the recycle bin. What can I do to shrink this to a minimum?
My home built HTPC is based on Asus M2n-SLI mobo and ATI Radeon HD 5450 video card with HDMI out to Onkyo 7.1 receiver which passes video and audio via HDMI to Olevia 36 inch LCD TV. PC (ATI card)-- HDMI out --> stereo receiver -- HDMI out --> TV The HTPC is never turned off. When I turn on the receiver and TV components to watch TV, Win 7 (Home Premium, 64 bit) will mute the system. I cannot just unmute. I have to go into Control Panel > Sound. There I find only one option (expected): AMD HDMI output.When I right click and choose Test option, it works just fine. I make no changes to the configuration and the sound/speaker icon in the system tray is normal. Then I open Media Center and everything works fine. When I'm done watching TV, I turn off the receiver and TV. When I start another session, the problem is back.I did not have this problem with an older receiver but using completely different component connections. PC -- HDMI out --> TV -- audio out --> old stereo receiver.
I have recently purchased all the parts for a computer from Newegg (still waiting for it), with the understanding that the HD graphics capabilities of the Sandy bridge Pentiums will be more than capable of playing back most formats flawlessly (and being able to convert some odd formats to WMC-friendly versions ahead of time), alongside beng used as a sort of download server for the house.
I am copying files from a WHS 2003 to a back-up drive on a HTPC. The WHS and the HTPC are connected physically to a router. The back-up drive is USB 3.0 and plugged into a 3.0 USB input on the HTPC.
The transfer rate is only 40MB/second. Why is this? The data is being transferred via CAT6 cables from the WHS/Router/HTPC and then USB 3.0 to the external drive
i stupidly downloaded imesh and my mcaffee detected the trojan but it doesnt detect it as a threat which is so confusing because isnt mcafee is suppost to be a security software...? anyway i downloaded other softwares like spybot, super anti spyware emisoft, avg, malwarebytes and all kinds of other ones but they dont detect anyting! i finally downloaded trojan remover 6.8.2 and it renamed the file or quarantied it or something and i shred those but how am i sure that its wiped off my pc? i shred some files named imesh and idk what else but i just want to make sure my computer is safe!
We fixed it, and although I had some photos and whatnot wiped out.. the damage wasn't too bad.The only issue is that I still have this window open up with certain things that says "I need to use one of these programs (Below is listed: iTunes, Internet, etc.) to open up the cmd file.I have tried searching for this file in the start search box, but it says..C:Windowssystem32cmd.exe Application not found It has caused my iTunes to stop downloading any of my videos or movies, too.
i built my new pc a couple of weeks ago, with mostly new parts (kept my psu and hdd). my pc keeps on completely freezing (no audio, can't move the mouse), forcing me to force shutdown and turn it back on again. sometimes after turning it off it works fine, other times it freezes again at any point during startup (once during bios, sometimes during windows setup, and sometimes minutes after it is fully started). the problem is, this freezing happens randomly. so far it's occurred while the system was idle, while watching a Internet video, and while opening google chrome. what is weird is how it rarely happens during gaming. i played 6 hours straight of bad company 2 on max settings with no problems. i've also played about 10 hours of the witcher this week and have only had it freeze once. sometimes the pc will freeze multiple times in a day, and sometimes it will only freeze a few times a week.i've run memtest 86 and memtest86+ when i initally bought the computer, and it found no problems. i ran these tests again two days ago and it still found no problems. i also ran a couple of stress tests (using prime96) and the pc never crashed when it was under full load. when i use speedfan, my system is normally 29c, my cpu is 36c, my video card is 40c, and the "core" is 35c. the only thing it has a problem with is something called "aux" which changes from anywhere between 40c and 130c. i read on the internet that it shouldn't matter, but... that's what it is.i've also checked the error logs, and so far i can't really find anything that corresponds to the times that is freezing. i've also ran my computer with all the startup items turned off, but it also froze that way too.
i've messed with ram timings, and gskill says they should be set to 9-9-9-24-2n with a voltage of 1.5. i've done that in the mobo, with the exception of "2n" which i don't really understand.at the recommendation of someone else, i've started running my pc with only one stick of ram at a time. i just tried the first stick yesterday in the first slot, and it froze at the very end of the day (after i had already played the witcher and watched a movie on it).it was suggested to me that i run memtest with one stick in it at a time (which i haven't done yet). is that really necessary? i was under the impression that memtest simply found errors on all the sticks, if there were any.finally, as just a side note, i built my brother a pc very similar to mine (everything except the case and the hdd are the same) and he has had no problems with his yet, telling me that everything is physically compatible and that the memory timings must be right.
I am using acer as 4738z(intel pentium p6200). os: windows7.my adapter name is Atheros AR5B97 Wwireless network adaptor. i want to change mac of my adaptor completely.My mac address is 1C-65-9D-C2-68-AB. I want to put the value 70-F1-A1-5C-BE-7C.
when i tried to search for something, I noticed my search bar was gone from my start menu.So I went to google, searching for an answer, and...No go.I looked in my "Windows Features", and it is completely gone.without doing a system restore, or re-installing?
I upgraded a Win7 Professional 64 bit system to Ultimate, then downloaded Language Packs in Chinese and Japanese. Now I am able to switch between Display Languages as expected. But after my last return from Japanese as Display Language to English, I find that Windows Explorer shows date information in Japanese, and IE uses Japanese as its language. Yet the Desktop icons have English legends, and the Start menu is in English. So there is a mixture of languages. Is there a way to eliminate Japanese completely? Should I uninstall the Language Packs?
One month old asus laptop just stopped working. Now won't boot up. Goes as far as choice between "launch startup repair" and "start windows normally".. Tried both options but ends with blank screen. Tried online suggestion for asus of using F9 when logo comes up. does this mean the laptop is unrepairable.
I dont konw if this is a bug or what. But I can't seem to get certain websites to load that I was frequenting in the past weeks, but now find that the site wont load completely!Yes I am unemployed, trying to find work right now.
I installed Playon on my computer. My trial has expired and I want to remove the software completely so I can reinstall it and use another trial period. Please tell me how can I remove the software completely. Right now it doesn't remove completely and when I install after reinstall it still show the trial is expired.
I've got a fairly new Dell Inspiron ONE computer with Window 7. Every since I bought it new some website home pages intermittently will not load completely. Sometimes I can refresh the page and it will open. I keep the cookies along with defragging on a regular basis. After clearing cookies I can sometime reboot and the websites will load ok. Also sometimes the page may continue to load and sometime it will stop loading and only the website header will appear. Some days I can go all day and all website will load ok.
