Dell Precision 670 Running Windows 7 Won't Boot After Memory Upgrade?
Jan 22, 2010
My Dell Precision 670 will not boot Windows 7 after upgrading the memory to 8GB.Configuration follows:*BIOS A06*2 x 4GB SIMMS in slots 1 and 2. These are correct WS670/4GB PC3200 EEC registered modules as recommended.*memory fan is installed*3 SCSI drives with Adaptec 7901 RAID controller.I've got a dual boot setup, and the system boots and runs fine from the alternate OS (Win XP x64) just fine. The BIOS lists the memory as installed and shows no errors or problems. A memory test indicates that the memory is okay. When I try to do a boot repair from Win7, the Win7 OS is not listed and installing the correct RAID and SCSI drivers from the repair window does not make it visible. The partition is not, in fact, visible from the repair tool. When I put the old memory back in (4 x 512mb SIMMS in slots 1,2,3,4) the system boots and runs fine with Windows 7. What's up with this?
run Windows 7 on a Dell Precision 370? I have seen ppl say it is running. I had 32bit Windows 7 Ultimate working on my 370 for a few minutes. Then I installed Win 7 SP1 and it crashed. Now, I cannot get it to start or even freshly install again. I get Blue Screen Of Death ...F4 error, and it reboots. Does anyone have it running at all on a 370 or after SP1 it failed like mine? And which version of Win 7?
I have a Dell Dimension 9200 and have upgraded to Window 7 32bit. When I had Vista install, 4 GB of ram was the max the system would recognise. Now that I am Windows 7 can I up grade my ram over 4 GB?
Was just wondering if any of you guys are using the Dell Precision M2400. There's a slot at the battery compartment which fits a SIM card, plus it shows that it's got HSDPA capabilities on their site;
Dell Precision Mobile Workstations | Dell Malaysia
However,
I am unable to find the driver which is workable with Win 7 64 bit. It doesn't show much on their driver download page as well;
Drivers & Downloads
Would appreciate some idea on how to go about this!
I've just tried to upgrade my PC's memory from 8GB to 16GB and have hit a rather worrying problem in that the PC now refuses to boot. Initially, once I'd replaced the old memory modules with the new ones, I got three beeps on power-up, which I quickly established was the result of my not properly seating the modules. Once I'd made sure they were firmly inserted I tried again, and this time all I get is the computer powering up - so all the lights come on and the fans kick into life - but then it powers down again without even attempting to boot: I don't even get to the BIOS. After a few tries I decided that it might be an issue with one or more of the new modules, so I swapped them back to the original 8GB kit and I still get the same problem. My PC is essentially DOA. Whilst I was inserting/re-inserting modules I did try to avoid and issues with static discharge. I wonder if perhaps I've disturbed a connector somewhere, although I couldn't see any signs of this when I re-opened the case to check.
The new modules are a 16GB Corsair Vengence DDR3 dual-channel 4-module kit (4x4GB). They were replacing a 4 module 8GB DDR3 dual-channel kit (4x2GB), so in both cases all four slots were in use. Motherboard is an Intel DP55WG, which is listed by Corsair as being compatable (16GB is the max for this motherboard). I've been running this system for two years prior to my upgrade attempt this evening, and it's been rock solid with no issues.
Maybe I should reset the CMOS for instance? Note that I'm not a hardware guy, and messing around inside the case isn't something I normally even consider trying... But I thought that this would be a very simple, trouble-free upgrade!
I have tried F8 for the advanced boot option, but the screen I get does not offer advanced boot as an option. I get a screen with six line that all have vista in them and am unable to do anything in that screen. It will not boot when b or enter keys are hit it won't do anything when I try select enter the command line and I am unable to exit this screen using esc button, I have to manually turn off computer. How do I find the advanced boot screen for dell inspiron E1505 with windows 7 professional?
I assembled a PC a year ago based around the Asus M4A87TDUSB3.0, with it was bundled a Phenon II X6 1090T and 2 x 2 GB fast DDR3. I have a 750W PSU, running a Radeon HD5570. I have a dual boot config, with Windows 7 64bit as default but also XP as other OS because there are some old games I really like that only work in XP (I tried emulation but software rendering isn't up to it). 90% of the time I'm in Windows 7. I've set up the system to that the Windows 7 partition isn't visible to XP, so that my Windows 7 restore points don't get wiped out when I boot into XP.Anyway, to cut a long story short, system has been working well, reliable and without issues for the last 10 months. However, a couple of months ago I decided to install a second drive of the same size but faster. I migrated the entire contents from the old drive to the new faster one without problems. I then reformatted the old drive and made it a dedicated backup drive for Genie Timeline. All worked well.
A couple of weeks later, I decided to upgrade the RAM from 4GB to 16GB and used Crucial's system scanner to find suitable upgrade. I took out the old modules, installed the 16GB new ones as a complete kit (with same latencies etc). First boot didn't seem to go well, system hanged before Windows Logo. I rebooted, went into BIOS and set the memory timings to Auto and set up Memory Counter to show on screen. I rebooted and it showed 16GB and it then booted into Windows normally. All fine, I did a Windows system rating and got 7.4's and 7.5's on everything apart from the HDD which comes in at 5.9Problem is, I now randomly get slow boots. It probably happens once in about 5 times, the entire boot sequence will take around 14 minutes whereas normally things are fine after about 3 minutes. I've pared down startup programs in MSconfig to really just the stuff I need to get by, so I know it's not that. If I shut down and restart, the chances are it boots fine again. It's not Windows Updates causing this, I can see those when that happens. I've taken out the memory modules and have cleaned the contacts with Servisol, unplugged and plugged the HDD connections back in. For a few days, the problem seemed to go away but it then came back.
When it's in its slow mode, everything is a bit sluggish, it's almost like I would imagine it would be with a minimum amount of memory or if it was running some heavy process in the background. I also notice when it's like this, that rather than the drive light being solidly on when booting, it's more of a fast flicker, with periods of inactivity lasting a few seconds.I'm not a technical expert, my guess is that it's either the hard drive or the memory. However, I'm also wondering if there is something in the BIOS that I need to do. Also, I've noticed that when shutting down, sometimes it doesn't quite feel like it's shutting down right, by this I mean that usually, in the last second before power off, the chassis fan runs to max as FanXpert hands control of the fans back to BIOS I guess
To start, I have Windows 7, on Sony Vaio laptop. I have been working on the issues with the malware removal team, but now machine looks clean, I am still having issues. When starting the computer and going to the task manager, I can watch explorer.exe start at about 18K memory usage and then grow constantly until it is running with almost all of the computer's physical memory after about seven min. I cannot get the context menu to show up after a few min by right clicking on anything. I had been experiencing "freezing" while playing Eden Eternal (an online role playing game) before that, which made me consider malware and seek help here at BleepingComputer. The freezing has ended, last time I played on that machine at least, but now there seems to be some issue with the explorer.exe taking all of the memory. I haven't been using the machine since I don't trust that there's not something running in the background that shouldn't be. In resource monitor there were "connections" that had "-" for both the name and the PID, but I don't know if that was the malware of if that's normal somehow? Issue with explorer.exe seems to be limited to only one user account, and not the other one. That is to say that if I log on one of the other accounts explorer.exe behaves normally, as far as memory usage.
I own a Dell XPS M1710 running Windows7 (5 years old). The graphics card has already been replaced once (after 1 year) due to a well know heating problem (made tolerable by cooling pad). I get Blue screen and Memory Parity Error some of the times I start up but mostly it freezes at the black screen point. Memory check gives all clear and I have tried swapping out all of the RAM with (working) modules but still get the same error message. Tried updating the graphics driver, no change. Tried disabling the Graphics device in Device manager and this had a slightly different blue screen but the same basic result.I suspect the graphics card Nvidia Go 7950 GTX because the fault first happened while playing an MP4 file.
I am trying to format my hard drive and reinstall windows 7 as my hard drive is running out of memory tried removing some programs but is not doing much my hard drive is 232GB I only have 28GB left, how to format my hard drive.
A few days ago, I get this little Windows pop-up on my taskbar saying that my computer is unprotected and has been infected with a trojan (couldn't remember if it said which one exactly but I believe it said Alureon?). Afterward, my computer has been running very slow and the CPU/Memory widget I have pinned on my desktop shows they are pretty much maxed out, all the time, even while not having Internet Explorer or programs open (none that I have knowingly opened myself, anyway). I went out and bought McAfee Anti-Virus 2013 yesterday hoping this would resolve the problem. It did find 10 trojans and removed/quarantined them, but nothing has changed as far as system performance goes; everything still runs slowly, and opening even the smallest of programs like a calculator takes at least a few seconds.
In trying to install my Sidewinder Precision 2 joystick in my new Windows 7 computer, I get a message that in order to install it, I need a 64 bit version.Does Microsoft provide upgrades for this?
I have Windows 7 Ultimate 64-bit.Ok, so heres my problem. Maybe 3 or 4 days ago my physical memory started running at around 30%-40% (around 1.5gb), and this is at idle and starts happening right at start-up. Normally in past it runs at around 10% (600mb or so). I have noticed it mainly when plaing SW: Force Unleashed and Dawn of War 2. Gameplay runs fine for maybe 3 or 4 seconds then freezes for 10 seconds then is fine again for 3 or 4 seconds and so on. I have tried disabling services, clean boots, virus scans, searched every forum maybe in existance and have found no soloution. I have 4gd DDR3 Ram (2x2gb sticks) and a 3.2ghz Quad Core AMD processor. Also i have noticed that my CPU usage is around 1 or 2% which is rather small isnt it? In my event log, i have been getting multiple errors relating to a bad block in my hard disk. This error repeats about every minute or so.
Brand new Dell Precision M4700. You can restart or shutdown the laptop at numerous times and on occassion the laptop gets stuck at the splash screen (where the windows come together), and will sit there for hours on end. Sometimes a single hard reset will allow it to boot, and be on it's merry way. System runs great once it boots into Windows.I'm not running any external drives on it. I've encountered issue on and off docking station, or running on power and or battery.M4700 with core i7, 16 GB Ram, Quadro K2000M, 256 GB Seagate OEM SSD.I checked hard drive with HDTune, and it checked out okay, except for 1 communication error, so to be on the safe side, I had the drive replaced. Still did it.Did a repair installation of Windows 7, still doing it. There's nothing different installed on this machine that isn't the exact same as the M4600s at the office.Is there a log that can be looked at, and or turned on to see what's causing it to hang at the splash screen? A few times it will go past the splash screen, but never displays the welcome screen (displays just a black screen).
when running memory certain intensive applications like VLC (when watching videos) or uTorrent, I intermitentley get BSOD crashes (screen shot below), which can happen every 10 minutes to several hours apart.
I have this HP HDX18 laptop for almost 2.5 years now. It came with Vista 64 bit installed which was later upgraded to 7 Home premium. It worked fine until Jan 2012 when it started slowing down to nothing. I got it checked and cleaned by the tech support for HP(pccare247) and also updated the drivers for sound, display and BIOS. Now the system runs fine until any media played whether offline or online. After that it slows down to nothing and the sound becomes crackling and also with a delay and distortion. The system slow down and the crackling sound does not come at the beginning and when it happens the CPU usage reaches 100% and stays above 90% until that multimedia is turned off. Also, the memory usage reaches 2.7 GB out of 8 GB and never comes below 2.16GB. What I noticed is as soon as I turn the WMPlayer off the CPU usage comes down all of a sudden to 15-20% and after sometime stays between 1-5% but the memory usage never comes down from 2.16, that is the minimum.
Sometime I do somewhat intensive processing that causes 85% of my 6GB ram to be used. But when 85% is being used, my machine completely slows down for all other tasks including very basic tasks like opening Windows Explorer. Surely the remaining 15% should be more than enough to open Windows Explorer without any latency. I'm using 64-bit Windows 7 Ultimate. Also, I should state that the CPU usage is very low at these times.
my computer is running real slowy cpu usage is at 100% and phycail memory is at 82% can someone help me plz? it is a compaq windows 7 intel cerlon updates all up for windows and computer
I just purchased Windows 7 Home Premium to upgrade it from Windows Vista Home Premium, and when I popped in the disc, it does not show up! I tried a different disk, and yes it worked. I also tried putting the Windows 7 disk into my friends computer, and it showed up. I have tried many different things, and nothing works. I've tried re installing the driver, updating it, and several different fixing programs.
Running Windows 7 Home on a Dell Inspiron. My account was setup as an administrator account and shows as such under account management. But upon boot up I get a message about not being able to run a startup program because I'm not logged in as an administrator. Also, when going to DOS prompt, I can't run chkdsk /f because I don't have the level of permission required.
I run a Dell M6500 laptop with Win7.When connecting to the internet it starts downloading "stuff', sometimes after 5 or 10 minutes, which I have no control over or find out where it is coming from. I have disabled auto update and my anti virus etc. If I go to explorer for internet history the files in doc and settings are locked. I have wiped the hard drive twice and started again from scratch, no luck.I tried to load Win XP but it will not load it, is that because it is a Dell? All my software is legal, and my anti virus is updated after notifying me it is doing so. When starting from fresh without any extra programs it does it also.
I have a Dell 8400 and a few questions about upgrading to Win 7 64 bit. (I am a complete NoOb when it comes to installing an OS).
First my specs are...
CPU Type Intel Pentium 4 HT 630, 3000 MHz (15 x 200) Instruction Setx86, x86-64, MMX, SSE, SSE2, SSE3 L1 Trace Cache12K Instructions
[Code]....
I will have 2GB of this RAM Thursday with another 2GB of the same RAM the following week or the week after that. Corsair Dominator DDR2 Ram Memory PC-6400 800 MHZ [URL] After the RAM I will be getting a new Graphics Card. Also I have a spare 650 watt PSU if needed.
I ran the Window upgrade advisor and the only things it flagged was (of course) that I only had 512MB of RAM and outlook express. It did say custom installation required, whatever that means.
1. My first question to everyone is, can my Dell even run Windows 7 64-bit? I googled around and it seems possible.
2. My second question is can I install it with the 512MB of RAM I have now?
3. My last question is can I install this along side XP on my HD?
4. My third question is does anyone know of a good very detailed step by step Noob guide for installing it next to XP?
I have never installed an OS before and if it does not work I am screwed!
I do know it is better to do a fresh install and no I cannot by another HD right now, I know they are cheap but I will be scraping together all I have just for the RAM and Graphics card.
My problem is that, I really only have the time to do this over the long weekend and cannot wait for the RAM to get here. The guy on e-bay is a clown and did not ship it when he was supposed to and it will not be here in time.
I just need it up and running and can add the RAM as it comes but I am under a serious time constraint and if I don't get this done now over the Memorial day weekend it will be a long time before I have enough time to do this.
I have a Dell M1330 laptop purchased some years ago which is currently running Windows 7. Despite my latest attempts to correct the audio problem, it still persists. My internal speakers are the only ones affected by this problem. When I plug external speakers into my computer they work just fine. The problem doesn't change depending on what type of audio or video I am running. I have run the windows 7 integrated driver updating software and it has said that all of my audio drivers are up to date.