I seriously don't know what happened to my computer recently. Yesterday I was trying to boot my computer in safe mode and when I turn on computer in normal mode, it showed a black border around the screen. I tried to check my setting(resolution and graphic card setting but still, the problem exists) My resolution is 1366 by 768 which is the native resolution and my graphic card is NVIDIA GeForce GT 525M. The border is about 1cm think, it is around the whole screen and my screen size is 14.1inch.
I tried Linux yesterday, and wrote over my previous Windows bootloader files with GRUB.
I later that day (as I could not boot into Windows 7), I deleted the Linux partitions with Windows 7 DVD. Now, after BIOS I just get a white blinking border on a black screen.
for the past month i have had an issue where before the log in screen would show, it would be a blank screen with a cursor, that i could move. (It worked normal in safe mode) I normally would just ignore this problem and it seemed to go back to normal after a little while. Well yesterday it didn't go away, so i went online looking for a solution, in safe mode. I've read to disable/enable drivers, re-install drivers, just plenty of things. And the result of all this is that my screen resolution wont go back to normal, and there is a black border around my screen, around a half inch. Also, my computer has been running EXTREME slow lately.
I have been encountering a problem with a small netbook which has a 1024 x 600 screen resolution. The problem is that the window of some application is un-resizable ( I've also tried to download a small registery hack which makes it possible to resize un-resizable windows, but it seems like it won't work with that one)So, as you know, it is possible to partially hide a window on the left, right and bottom borders of the screen, but it is impossible on the top border, where the window would just go down again (while it can't be maximized though ).Is there any way to make it possible to hide a part of the windows over the top border so I can see the bottom of the window ?
My wife did something on her PC (she doesn't know exactly for sure what & can't explain it completely me), and now she can't boot up her PC. She says it had something to do with changing the security settings for a program she uses a lot so it wouldn't keep asking her if she wanted to launch it, and that's when it told her to restart the PC, then it wouldn't boot up anymore.When you reboot, the screen eventually goes to a black screen saying "Windows failed to start. A software or hardware error may be the cause" or something to that effect. It offers me the option to "Launch Startup Repair" or "Start Windows Normally".If I Launch Startup Repair, nothing much happens --- it says it's adding files, then it looks like Windows is about to boot up, then it goes to a black screen for a long time & nothing happens.
If I choose Start Windows Normally, it simply reboots & eventually brings me back to the same screen again.I've tried using rebooting and selecting ESC to get to the boot menu, then installing the Win 7 installation disc & selecting the DVD drive, then I select thelanguage, then I click Repair, but it sits there forever with nothing happening.I also tried an outside boot disc I found on the web & it doesn't launch.
i have a Dell Vostro 1520 and im running Windows 7 with a 32bit. It is only 2 years only. It started about a month ago. I was on my laptop viewing and deleting some unwanted photos i had. A few minutes later i realized that i deleted a photo that i wanted. So i went to the recycling bin and restored that photo. When i went back to my photos and went into the album, it said something like i do no have permission to access this folder. Please press continue to get full permission. I clicked continue and i got the access i should have. Now i tried many more random folders and the same thing happened. Also when i came out of the folders, the folders had a big pad lock sign on the front of it. After that i shut down the laptop and went to turn it back on. The laptop will power on like normal. I can press f12 for the boot options. which i have already tried many times. I also tried it in safe mode and what-not, but still nothing. I can hear the fan and stuff spinning up like normal. I have also put and CD into the CD ROM and that spins up fine. So after the Dell logo on the screen, it goes black and stays that way with the cursor. You can move the cursor around no problem. I should also add that the battery light is and has been flashing for a good wile. Its flashing orange and blue. I'm wondering if this has anything to do with the battery. Because my laptop will not charge with the AC adapter in it for many months now. It will only stay powered on with the AC adapter plugged in. One more thing. The LED lights over the buttons. None of the are flashing, besides one, on the far left. And i cant find out anywhere what this LED light stands for.
My son has a Toshiba Satelite P205 that he just upgraded from Windows XP Home Premium to Windows 7 32-bit. After the upgrade completed the computer booted fine. The within 20 minutes he got the BSOD and the system rebooted. Now he can't get Windows to fully start. We've tried all of the options from F8 with no success. We have the Toshiba System Recovery Disk but it won't launch. (The Boot sequence has been changed to boot from CD/DVD and then the Hard Drive.)The Memory Diagnostic from the Windows 7 disk ran fine with no errors. I'm thinking I might need to re-format/wipe the drive to start fresh but don't know where to obtain a boot CD(no floppy drive on this laptop). Does anyone recommend a software that I can purchase to clear everything without destroying the CD/DVD accessibility so I can then use the System Recovery Disk to put it back to the original factory Settings?
My computer has a problem with crashing while playing a video in full screen. When it crashes the screen turns black while the speakers give out a buzzing noise. Everything is unresposive the only solution is to turn it off with the power button. It happens in any full screen video online or offline and even visualizations from windows media player and iTunes, but only in full screen. I don't think it's overheating either because sometimes it takes 30 mins to crash and other times it will crash immediately when put in full screen. *I've tried setting it back to factory settings thus reinstalling windows. *All the directx features are working with no reported problem there.* I don't think it's a memory issue in the computer, as my specs are:
Windows 7 64-bit Processor: intel core i5 3.20 GHz Ram: 8 GB Graphics card: NVIDIA GeForce GT 220 Graphics card memory: 0.5 GB Any other ideas?
I have an Acer aspire 5732Z. I turn my laptop on and it shows the starting windows screen then just goes to a black screen with a cursor. I tried to do systems restore but it said that I did not have a system restore point. I cannot start in any safe mode. I have all my pictures, uni work etc., and I am terrified I've lost it all. I've only had the laptop a year.
I'm using I have a DELL4500S desktop, on startup it will not go to the login screen, the screen is just black with the cursor showing. I've tried restarting the computer, unplugging everything and restarting it. Nothing is working. When it first starts a pop up shows and says "This Application has failed to start because SAMLIB.dll was not found. Re-installing the application may fix the problem."I'm not sure what it's talking about and what to re install and I can't reinstall whatever it is because I can't get to the start menu.
I just upgraded to Windows 7 on my Toshiba Satellite Special Edition laptop that came with Vista 64bit and the other night i downloaded iTunes 10 and told me to restart my machine so I clicked ok and then my laptop shut off and when it came back on the Toshiba screen came up as usual but seemed to stay on longer than normal then it goes to a black screen with a underscore that blinks for a few moments then becomes solid. Ive tried to use the "F" keys to get different boot options because i have the windows 7 ISO disc and a ubuntu disc that I could use but whatever i try my laptop wont process it just does the same thing over and over again and bever proceeds to the actually boot up windows.
I have a Toshiba laptop running windows 7. It has been running like a well oiled machine since the day I got it.I turned it off to watch TV, then when I turned it back on, the screen shows the Toshiba screen for about 1/4th of a second and then goes black.If I hit F8, F10, or F12 nothing shows up.
I have recently bought a computer and I have found that when I turn it on it runs normally until after the "Resuming Windows" screen, where everything turns off and the screen goes black. It had been running well for the last few days, so this came out of nowhere.I have searched this problem and I come up with a bunch of different solutions but no one agrees. The most common reason (apparently) is my version of Windows 7 Home Premium (x64) and I need to install something or other. But I can't even get to the desktop, and no one really explains it simply. [code]
While attempting to restore a previous backup of my system (with Norton Ghost 15), I got an error, and the system rebooted. Upon reboot, I get the black screen of death with just the cursor instead of the usual login screen. I have tried the following thus far: These all give me the black screen of death with movable cursor:boot in safe mode boot in safe mode with networking boot in safe mode with command prompt last known good configuration I did an initial system startup repair which went through and said it repaired it, rebooted, but no change. I did a pre-boot diagnostic test - nothing memory test - nothing tried restoring from restore point, but it says I don't have any (LIES! BLASPHEMY!) tried restoring from restore point on external disk - seemed okay, then failed. chkdsk - found some stuff, fixed it, no change. tried ctrl+alt+del on black screen of death - nothing
Now, I know that the hard drive itself is alright, that is, the information is still all there still. While I can't give you exact specs, I can tell you that I am on a Dell Studio XPS running Windows 7 home premium 64 bit. I'm at a loss as to what else to do. Despite being a black screen, with just a movable cursor, the system still appears to be running, as every few minutes, it will show the "thinking" cursor, where it shows the little circle next to the arrow.
Recently, my computer starts up windows and after the loading screen it just sits at a black screen forever with a cursor and it doesn't even make it to the log in screen. I have tried safe mode with the same results. What I've Done So FarTried to Repair Startup with Windows DVD Tried to use sfc /scannow at boot (Says pending changes and needs to restart) Tried logging into my Ubuntu partition and virus scanning (None found) Tried copying Reg Files from Regback into config while I was in Linux Tried to Repair Install (But I can't log into Windows ) Tried to bootrec /fixmbr /fixbot /RebuildBcd (Which destroyed my dual boot linux grub, but I was desperate. And still nothing) Interestingly though, after I do /RebuildBcd command it says something like "Found Windows Installations: 0" Tried to System Restore (Gave me an Error, wouldn't you know) At this point I'm not to confident that this can be fixed. If anyone has any ideas I'm willing to try. Or if you have any snazzy suggestions on how I could fix it using another computer, I have a different Windows Pro x64 computer that I can put the HD in if there's someway I can save my data/fix it/repair install from there. I just don't know how.
Edit: I finished the chkdsk and there were no bad sectors, though it did give me a message "Failed to transfer logged messages to the event log with status 50."I did a Windows Defender Offline scan with no viruses and I'm currently scanning with Kaspersky Rescue disk. I don't believe it is a virus, I think it's a corruptregistry at this point. I had just cleaned my registry with CCleaner before the shutdown that led to this >.<
i recently just installed a clean install of windows 7(instead of a upgrade from my vista.i got the free upgrade),now everything works fine expect when after the windows 7 splash occurs there is about a 10 second delay were the screen is just black with a cursor.
i have an HP Pavillion dv7 with windows7. It is less then 3 months old. Problem- Yesterday the screen went black while i was watching a video, but the sound kept going. so i restarted the computer, and the screen works until you get to the login screen it goes black again. SO i called customer service at hp, and we worked on it for an hour.THe one thing that seems to work is when i go to the device manager, uninstall the display adapters, and restsart in normal mode, then i go and reinstall the ATI device thing in the recovery manager, but everytime after i reinstall the ATI display device thing, it ends up going black a little while later again. lol
I'm trying to paste an MS Word Document in Windows 7 with a Page Border into Outlook and the Border disappears. I've tried Googling and nobody seems to have this problem. I've tried Control A to Copy Text Control C to Copy All & Control V to Paste & the Border disappears. The recipient is requesting a Word Document as opposed to putting it in Notepad.
is there any way to change the invisible border when selecting a file to just the size of the folder or what Xp Was also is there any .dll i can copy from Xp to make it possible to arrange them in the order i want
Just wondering if its possible to have the border effect on each side of the screen with dual monitors. Mine are only on the far right and far left, no middle as it seems logical if you have 2 monitors you might want to have 50% coved with one window and have the 2nd 50% with another window, then you could full screen a 3rd window or just have 2 more halves. but the current way it works is 2 halves then a big empty space in the middle or 2 full screens.
I love the easy and quick way to organize/resize the windows but its very inconvenient to do this manually for half of the screen.
yesterday when i was making log out from my computer, there is no log out screen!! just black screen and mouse cursor, and when i did restart again , no logon screen appears or no any thing in screen , just black screen and mouse cursor too.I was tried every thing and no difference :safe modestartup repairrestore to some point (i dont have a point)upgrade windows or reinstall iti think the things maybe was made this poblem are :i was edited userinit.exe value from registry by deleting the comma from the end of its value. i used Windows 7 manager to make some clean and fixes some things on computer.
I'm running Windows 7 Home Premium.As I brought my computer out of sleep mode the computer had crashed with the screen showing vertical, multicolored lines that vaguely resembled gray.I had to hard restart my computer and after the splash screen, the login screen with all the users never appears, nor does my cursor.Nothing is on my screen except a faint glow indicating that it's active.
Whenever the Windows loadscreen passes the screen goes black and I can move a cursor around the screen. I have had this happen before and fixed it with bootrec.exe but I can't seem to get that to work this time. Safe mode has the exact same black screen problem.I have done chkdsk and sfc scannow - Didn't fix it.When I boot into Kaspersky Rescue from a USB drive it mentions that I need to shut down windows properly before continuing. I would like to do this but I can't.I have tried changing the active partition on information in some of these other threads - It didn't seem to work.All disks are healthy according to the DISKPART and Partition Wizard. I have done the HP hardware diagnostic scans and everything comes up fine.
Just purchased 2 new (refurb) PC's for my wife and I. It's all I could find with Windows 7 still available. They are both HP Pavilion p7-1233w 64 bit Desktops running Win 7 Home Premium SP1.During Windows setup of PC #1, it asked for a restart. When the PC powered back up, it had a black screen from the start (before the Post screen). I power cycled it several times with no luck. Even switched monitors and video cables. The next morning it started normally with perfect video.I assumed the Refurb PC had a problem and set it aside for return.Been setting up PC #2 for a few days now with lots of restarts. All was well, until I did a restart just now. There was the identical problem. Power cycled the unit twice, and still had the black screen.Then I unplugged the PC, and pressed the power button to discharge the capacitors (fans ran for a few seconds). When I returned power and started the PC again, it functioned normally. I've done 10 quick restarts since to try and replicate the problem, but it only happened that once.
I love these PC's, and I love Win 7, so I hate to give them up. But I don't want the video freezing up on me every time I do a restart. I assume now, that PC #1 is not necessarily defective.Since this is occurring before the post screen, I wasn't sure if it could be windows related.
I got a bad virus on my computer about a week ago. I decided to use my windows 7 installation disc to reformat my disk drives and reinstall windows 7. The installation goes smoothly and I am able to login to windows. But after I install drivers and updates, then restart the computer, I get the "starting windows" screen with the swirling logo. I can hear the chimes that sound when I get to the login screen, but the screen is black. I can make the cursor appear by moving the mouse, but I cant do anything else. I never created a system restore disc, so I dont have that to help me.I have done some tinkering and will tell you what did not work so far.First, like I said, I used the windows 7 install disc to reformat my disk drives. Then, I reinstalled windows. I installed the updates for my graphics card and motherboard. When I restarted, I got the black screen. I restarted the computer and used F8 to do a system repair. This detects no problems. I tried to use the "startup repair" on the windows installation disc. This does not recognize a problem. I have tried it several times. Same result. Next, I tried to use the repair options on the windows install disc. I went to command prompt and typed in: bootrec.exe /fixmbr, bootrec.exe /fixboot, and bootrec.exe /RebuildBcd. (An interesing note: When I used the RebuildBcd command, it said that it detected 0 windows installations.) After the first time I did that, I tried the startup repair and got my first and only error message: "Startup repair cannot repair this computer automaticaly". I checked the details and it said "Problem event name: StartupRepairOffline". If you need the rest of the details, I can provide them. But I tried the repair again, and there was apparently no problem. Yet, still got the black screen.I then reformatted again, deleted both drives, and made new ones. I tried to install windows again, and I can get to my desktop.(One thing I noticed is that before I install updates, the computer is saying that my monitor is a "Generic PnP monitor on standard VGA graphics adapter". I dont know much about computers so this may be normal before installing the graphics card updates.)This time, I was connected to the internet and tried to install the system updates first. After all 120+ updates installed, I restarted and got the black screen again.I decided to use the install disc again to reformat, delete, and recreate the hard drives. This time I tried to install windows on the second hard drive (Disk 1) Again, the install went smoothly. I started installing the graphics card and motherboard drivers, but this time it told me that my disk drive D needed to be formatted before use. I reformatted it (this took MUCH longer than the format option on the install disc), installed the drivers, and restarted. I still cant get into the login screen. Finally, I used the install disc to reformat, delete, and recreate the disk drives. This time I installed windows on the first hard drive (drive 0) again and got to the desktop. Now I tried to install the motherboard drivers first, then restart. I did this and was able to restart and get back to the desktop. Next, I installed the graphics card dirvers, and then restarted. Black screen again.
his problem started with XP and I decided to upgrade to win 7 pro.
My PC has a black screen on wake up more times than not. Wake up is set for a login screen normally. My settings are screen saver after 10 mins then send screen to sleep in 20 mins, no hibernation mode, rest machine remains alive, runs 24/7 normally.
I have swapped the power supply and graphics card with ones that work in the same model PC and no joy.
When I click and drag on the title-bar of a window the window border moves to the new location then when I release the mouse the window springs into the re-located border.This has only started to happen after I changed the partition size of my c: drive. Obviously, some setting has been changed and I have no idea as to how to reset it.
Suddenly I have a yellow border around windows live photo gallery, and the photos have a yellow tint to them. This has happened in the last week and I have done a search, but not come up with any solution.
I'm just wondering if there is a way to make the desktop icons not show trough the transparent top border of an application? I like my wallpaper to show through it, but not my icons.
