where it boots up to the loading screen is fine, slows down and stops, then it will bring me to blue screen and restart to the point where it has black screen telling me boot up was unsuccessful, and i can go into all 3 safe modes or boot normally, have tried all of them and non of them even boot
View 6 RepliesFirst after doing an ordinary restart, my vista (ultimate) gets stuck for a LONG time at the loading screen and does not move, with the green loading bars. this happens every time i try to restart. i pop in my original vista disk and start the repair process...it says it found something wrong with my startup and it found what was wrong and that it was repaired. after this i get the message NTLDR, which is a whole nother problem. i ran the below to fix the NTLDR...
1. Put the Windows Vista installation disc in the disc drive, and then start the computer.
2. Press a key when you are prompted.
3. Select a language, a time, a currency, a keyboard or an input method, and then click Next.
4. Click Repair your computer............
I have scheduled a chkdsk to take place the next time I restart my computer and when I restarted it, the problem started! After the Boot Screen finished booting nothing happens, the screen stays blank. I have left it for hours and still nothing happens. How can I solve this problem? I also wanted to mention that I have changed my boot screen using this tutorial. I didn't really have any problem after following that tutorial but I only wanted to mention that...
View 4 Replies View Relatedall day I've been trying to sort this out but to no avail. I've searched Google like crazy, and whilst I've found that others have had this issue there's been no real resolution. My system boots all the way up to the point of the loading bar, then it goes blue screen and restarts. I've found that it loads up in safe mode, and I can access all my drives (I've tried unplugging external devices), and I'm 99% certain that running a system restore would fix the issue. HOWEVER, safe mode revokes me of all rights to perform any system based tasks, so obviously it won't allow me to run system restore, regedit, pretty much anything. Here's what I've tried so far:
-Running system repair through a boot disk, it didn't find anything wrong
-I tried running system restore through the boot disk but apparently there weren't any restore files (which isn't true)
I have a Toshiba Satellite L300D -01Q (PSLC0C-01Q08C) that is running Vista Home Premium (SP unknown). The kernel completely loads to a black screen (active / backlit black) with only a moveable mouse pointer. None of the Recovery Options have helped and I can't do an Upgrade Install because I can't get to the GUI.
My priority and objective is to save this system and preserve files, programs and settings. I read Brink's How to Repair and Verify the Integrity of Vista System Files with System File Checker and I'd like to try sfc /scannow, however, I get the following:........
I guess you can't call it the Blue Screen of Death anymore as at least it collects data and reports the problem and boots back up (or does it?). I've had a total of 3 of these screens and am wondering how I can view what took place and possibly find out if there are any steps I can take to prevent the same thing from happening? Is anyone else experiencing this? I couldn't find anything in search function on several bases.
View 9 Replies View Relatedthe PC boots up very slowly and I began to occasionally receive Blue Screen Errors. I think I have most up to date drivers for my hardware and applied most of the tutorials in the Speed Up the Performance of Vista Tutorial on my PC. However I have a RAID 0 setup and 3 partitions on my HDs and couldn not apply the #6. Enable Advanced Performance for the Hard Drive tutorial.
At system startup up Windows Explorer crashes sometimes and while playing Adobe Flash Movies from a CD I got an Blue Screen Error after I restarted the computer in Safe Mode with Net Support and now I am writing this post; the computer booted faster in safe mode without Kaspersky AV and ATI CCC.
After boot the windows reported that the cause of unexpected error was Intel Matrix Storage Manager(iaStor.sys)? I have used Uniblue Driver Scanner 2009 to scan the drivers and update them as necessary recently. How can I find out if there is any driver conflicts or cluster on the main drive? I have SP1 installed with 4GB physical RAM whose only 3070 MB can be used and have the latest drivers avaible for my GPU and the latest BIOS for my MOBO. I also experience lack of performance while displaying desktop, executing a program. Furthermore I want to know how can I access Boot logs manually.
I used a friends computer to download and burn an image file to disk. In the course of doing so i had to download and install a img burner(i think it was called ISOBURN) which i then uninstalled. Sometime later that day the system was rebooted and now the system no longer boots normally, it boots to a WINDOWS98 startup selection.
If i try and select any of the options from this menu it returns that it "cannot find himem.sys...blahblah...please enter the path to command.com. I have already restored the registry to an earlier backup and rolled back the entire system 2 weeks using the OEM restore disk niether of which corrected the issue.
after my computer boots it gets stuck on a black screen with a mouse cursor in the middle. I have been researching and reading for a solution but have not found one that works for me. I can't boot into safe mode or even safe mode with command prompt so i cant do any registry fixes which some people suggest. Iv also tried last known good configuration but that didnt work either. ctrl + alt + delete doesn't work either. iv tried doing a clean install and using the windows diagnostics and recovery toolset version 6. but they havnt worked either after the loading files bar the KSOD comes back again, it is like the computer cannot read the discs or it wont boot from them.
View 4 Replies View RelatedOnce vista boots from the cd it goes to a windows is setting up files,then goes to a black screen where there is a lilttle green bar moving. Now right after that it goes to a blueish screen where there is just the mouse cursor on the screen and just stays there? This is on all new hardware. Also this is a sata hard drive,
View 9 Replies View RelatedI was hoping that some of you guys could help me with a problem. As the title says, my screen goes completely black after the loading screen with the green loading bar, but before the usual windows vista circle is supposed to appear. I have also tried to use a vista x64 recovery disk. Here I only get the blue background a mouse I can move around on the screen, meaning I have no options to choose from. Does anyone know what the problem might be? And if so, how to possibly fix it?
View 9 Replies View RelatedList of Parts:G. Skill 4x2gb DDR2 PC2-8000 ram Intel Quad Core 2.4Ghz cpu Gigabyte GA-X38-DS4 motherboard BFG Tech 8800 GTS (G92) gpu thermaltech toughpower 700w psu Western Digital Caviar WD2500 hd Chi Mei 22" LCD Sound Blaster Audigy SE sound card LiteOn optical drive Problems started today when i tried to turn on my computer, im running Vista Home Premium x64. The loading bar screen would show up and then after that it would go black like usual, but then my monitor would show that there was no input available and the computer would hang in this state forever. Any suggestions? I know a new HD would probably fix it all but im not sure i really want to spend all the money, literally just built this baby 2 weeks ago!
View 7 Replies View RelatedA few days ago my display settings would not save and each time I restarted my computer they were different. I thought it would not get any worse however now when i start my computer the screen goes black just after the green loading bar. The computer is still on because it makes hard drive noises and my quickplay buttons are blue but the computer does not respond. It starts in safemode but it won't start normally. I have Vista Home Premium 32 Bit with Service Pack 1. Any help would be greatly appreciated to get rid of this black screen.
View 4 Replies View RelatedMy computer is freaking out and i cant figure out why. I try to start it normally and it posts and I see the green loading bar for windows at the bottom of the screen and then the screen goes black. I can load into safemode but that is all. I can not restore sucessfully.
View 9 Replies View RelatedI have a problem with Vista. When I start my computer, it displays a black screen for a couple of minutes before starting to load Vista. I don't really know what to say more, since I'm totally clueless with this one. What I've tried to do, is to update my drivers. I've also updated my BIOS. What should I try next?
View 9 Replies View RelatedIt boots on the F2 setup screen does several seconds of the loading bar, then my screen says 'no signal' and it goes back to the F2 setup screen and freezes. Then I have to turn of my computer by holding down the power button and start it again the second time where it boots fine.
View 5 Replies View RelatedRIght now im on the same computer on my BItdefender 2009/Iceweasel.So after i get a black sceen with a cursor that i can move where i want but it just stays like that.I tryed all the safe modes and they dont work at all.Plus i dont have a VistaDVD to make it worse.(My Original OS was Windows Vista Home Premium x32)I really dont know where the command prompt is on iceweasel but i know how to use it in vista.
View 7 Replies View RelatedFor about 1-2 years my computer ran fine until recently. Now, whenever I start up my computer it boots all the way to the Vista loading screen, seems as if it loads all the way, then shuts down with no warning. This happens at the same point every time. I tried putting in the Vista DVD and starting that up in an attempt to reinstall or repair Vista, but I get the same results on the same loading screen. The computer is custom built by myself.
Specs:
AMD 64 X2 4800+ 2.4GHZ
ECS GeFORCE 6100SM-M mobo
BFG Nvidia 8800 GTX
OCZ PC6400 2GB 800MHZ (Dual Channel)
Maxtor 160GB 7200 RPM HDD
Coolmax 600W CXI-600B PSU
(Everything is using stock settings)
The next time it started, the graphics were all screwed up and when it gets to thebit after the Windows Loading Bar it goes to a Blue Screen of Death. The computer then restarts and the same thing keeps happening. I tried running the computer in Safe Mode but it doesnt work either :/ neither do any of the other Advanced Options.
View 9 Replies View RelatedI've recently got attacked by some sort of virus malware and my AVG instantly asked me to reboot. After I rebooted and loaded the green loading bar, my entire screen turned black without the windows badge.When I clicked on the restart button, I'm able to get inside safe mode, network and command prompt but not start windows normally.. I've also tried chkdsk command but it showed 0 bad file.
View 4 Replies View RelatedI reboot the computer, boot from DVD.
I get the screen that says "Windows is loading files", and then I get the screen with the loading bar at the bottom (the one that looks a bit like the standard Windows XP loading bar) and then the screen goes black and nothing happens. I've tried leaving it for a good half hour, still to no avail.
Last night my pc was running fine and just before I went for some shut eye put my pc into sleep mode today I woke my pc only for it not to allow me to log on, mouse movement only nothing was clickable so after a short while I decided to reset upon boot I got the green loading bar but then a black screen after about 20 mins I gave up and tried a restore last good config.... Yeah nice one it bsod on me At 55% chkdsk and now I get a windows boot manager error file: ootcd
I tried Bootrec /RebuildBcd but it brings back an error that it can not create the new file as the file already exists. I'm not having much luck with the recovery disk for repair options as it can't seem to find the OS and brings back errors of can not recover everything seems on a go slow and ubuntu can't find my c drive even tried spin right and that can't recover a bad sector I'm at a loss as to what to do befor the fresh install option I'm on my last option to try use a back up store disk
New computer. Vista Home Premium. FSX continually stops loading and have to restart the loading process. Six times to get it loaded, but all sytems not functioning. Loaded Accelerator crashed whole system had to do repair of FSX and start over again with continual stoppage. Don't know where to go from here. It worked fine with XP
View 9 Replies View RelatedIv just bought a new PC, I put the vista CD in the drive and power up the computer. A screen appears saying "windows is loading files" and a bar that slowly fills up.Once the bar is full (suggesting all the files have been loaded), a new bar appears with microsoft corporation written underneath it.From looking at online install guides it appears that there should be a moving green block within this new bar however, it is completely empty and nothing happens. I have tried to install several times and left it for 40 mins or so each time, but i keep getting the same problem - i get to that stage and it seems the install freezes.
View 7 Replies View RelatedMy windows xp that I have had for about 2 years suddenly started to shut down and restart on its own. Out of the blue, over and over. Boots up shuts down, Boots up shuts down. I use it for my business payroll and bill paying. When I do get it to stay on for a couple minutes I have to restart my active desk top. I have tried defrag and cleaning it up. Checked all my plugs and tried everything I can think of.
View 9 Replies View Relatedonline backup installed an update on my extremely stable Vista Home Premium. It asked me to reboot and when I clicked reboot, the system froze up. Every time I boot, it will freeze within seconds of loading the desktop.
I would seriously love to get this fixed as I have reinstalled Vista 4x, the last being 18-months ago
How may I resolve OR troubleshoot this issue? I have done a restore point back 2 weeks, but thats as far as I can go without getting an error.
Quote: Microsoft's new Windows 7 operating system boots slower than its unloved predecessor, Windows Vista, a PC tune-up developer said today. The claims by iolo Technologies, a Los Angeles maker of PC software, contradict Microsoft's boasts that Windows 7 starts up faster than Vista. More - Windows 7 boots slower than Vista, says study
View 6 Replies View RelatedI have a problem where the machine automatically boots up when hibernated. this happens approximately 2 mins after hibernating.. it's not always 2 mins. the time differs.
View 6 Replies View RelatedI have a Vista computer that always boots into the recovery options and trys to repair the operating system. How can I stop this from happening? Even after repairing it does not try to boot normally! Safe mode does the same thing. Using bcdedit the RECOVERYENABLED is set to YES, how do I set this to NO? The computer failed to boot in the first place because of a thrid party service, normally I disable the service in safe mode but now the recovery options seem to be getting in the way.
View 8 Replies View RelatedI just built a brand new computer, it consists of the following: Q6600 quad core, EVGA 780i mobo, 8 gigs Corsair XMS2-6400 800MHz mem at 5.5.5.18 (of which only 2 gig during install), 2 150gig Raptors in RAID 0, and a Maxtor 300gig for additional storage. I am going to be putting in a 9800GX2 GPU in aprox 2 weeks(waiting for availability at my fav shop). For now I have an ATI X800 GTO GPU in it. Now all of these items are compatible with Vista(as far as I have found). After 4 installs that would not complete, I finally get to Vista desktop, the automatic update does its thing, reboots, and reboots...etc. I found a hard start from off it boots?!? So I turn off and put in 1 more stick of RAM(now at 4 gigs). Same prob, reboot snags over and over, but a hard start is good. I have a TON of components to install and hard start is not going to cut it.
View 4 Replies View Relatedi was using vista 32 bit vista cracked demo version since mar '08 with 160 gb hdd i didnt face any prob. But now i added 5oo gb hdd driver with 32 bit vista now my sys boots late and with 64x vista im getting differnt boot screen. my hdd is wd caviar green. i mainly use pinnacle studio and maya which one is better for me 32 or 64
View 4 Replies View Related