I don't know if this is the right forum but i wasn't sure which other group i could post this to. Does anyone know of a program that you can use to boot from cd into a file manager or something like that so if windows wouldn't boot i could still gain access to my files and copy them over my network to another pc?
I need to boot into drive D, the HP recovery partition, so I can restore the HP laptop to it's original state, since it's all hopelessly messed up, but I installed EasyBCD and told it to "Reinstall the Vista bootloader". And now when I boot I no longer get the option to boot into drive D.
I run vista 32 bit. I'm pretty sure it's Vista personal (PC didn't actually come with a Vista disk). I only use it for music and games,basic stuff. It's a Compaq....It shat itself recently, it wouldn't boot, so i borrowed the Vista Business disk from my dad to repair it/disk boot, and it worked fine, that was a couple days ago. Today it happened again, except it won't repair the same way. I start it up, it goes to the Compaq startup screen with 4 options; [Esc] Boot menu, [F9] Diagnostics, [F10] Setup, [F11] System recovery. Except I can never go to the diagnostics or system recovery menus, i press the keys and nothing happens. Then when i don't press anything it goes to a black screen with "Disk boot failure, insert system disk and press enter", so i do. Then it says "Windows is loading files" with a white bar below, once that's done it goes to the Microsoft Coporation green load bar that scrolls across over and over. Then it suddenly stops for a few minutes and a blue screen appears saying
"A problem has been detected and Windows has shut down to prevent damage to your computer DRIVER_IRQL_NOT_LESS_OR_EQUAL If this is the first time you've seen this stop error screen, restart your computer. If this screen appears again follow these steps: Check to see if any new hardware or software is properly installed. If this is a new installation ask your hardware or software manufacturer for any windows updates you might need. If problems continue disable or remove any newly installed hardware or software. Disable BIOS memory options such as caching or shadowing. If you need to use safe mode to disable or remove coponents, restart your computer, press F8 to select advanced startup options, then select safe mode. (pressing F8 does nothing for me) TECHNICAL INFORMATION *** STOP: 0x000000D1 (0x00000000, 0x00000002, 0x00000000, 0x87995395) *** nvstor.sys - Adress 87995395 base at 87991000, Datestamp 46671a61".....
I've read just about every thread about vista not booting and am completely at a loss. I am running Windows VISTA Ultimate x64, do not have the original disk with me as i brought this computer to work on to my vacation spot to do some work. After running a botched program, I got a msg saying the computer would restart automaticly. Having extensive windows knowledge I know this is never a good situation to be in. I am using a windows x64 boot disk that i found from neosmart as I do not have access to the original disk.
Download: Windows Vista x64 Recovery Disc — The NeoSmart Files
I have tried every option in recovery options. Just to clarify, after everything posts, without errors, I get a black screen with a white cursor that moves down a few lines and doesn't do anything after that.......
A customer asked if he created the recovery disc would he still have a complete working recovery partition. He is in fear of creating the disc then losing them.
4JHA.3676@TK2MSFTNGP06.phx.gbl> A customer asked if he created the recovery disc would he still have a complete working recovery partition. He is in fear of creating the disc then losing them.
I want to create a recovery partition on my windows Vista laptop. Pretty much i want to be pompted when the pc boots to hit f10 and have a count down of 10 seconds. I know this would be done through boot.ini however i have no idea how to do so. Also id make a seperate partition on my hd of ten gigs just for the backup image.
When I had XP, I had a startup problem so I rebooted with a Windows XP CD that came with the computer. It fixed it.
I'm not sure if this is called a boot or recovery disk, or both.
I was hoping to make a similar disk for my new Vista (Gateway)computer but I'm not sure how to do it. I read something about an emergency thing that takes up 3 DVDs!
I went to turn it on this morning, I just had a black screen showing the following words;
Press F2 to run Press F11 to boot menu Auto detecting PRI Master Atapai CDROM.
It then went to reboot and select proper boot device or insert boot media in selected boot device and press a key. I went into the BIOS to change the boot order and inserted my Vista home premium 32bit. I then got windows is loading in files. After a short while I got the black start up screen with Microsoft Corporation but after a few seconds it just froze. Moments later it went to a blue screen with white writing part of which said the following; A PROBLEM HAS BEEN DETECTED AND WINDOWS HAS BEEN SHUT DOWN TO PREVENT DAMAGE TI YOUR COMPUTER.
i can no longer boot up my computer as the boot/bcd file is miising or corrupt i found a windows artical on how to fix it and it didnt work ive also tryedd googleing the problem and got many results but none that seem to fit the problem or are helpful what can i do to solve this
I have a Dell Inspiron 530 Desktop and every now and then it won't boot up. I get a black screen with 'Windows Boot Manager' ," Windows failed to start. A recent hardware or software change might be the cause."
File: BootBCD Status: 0xc000000f Info: An error occurred while attemping to read the boot config data.
When I boot the PC with the Installation disc, it repairs it and it works until the next time. When I click on the details to see what is to be repaired, this come up:.......
I have windows xp installed right now and I dual booted with vista by re-partitioning my hard drive. After encountering problems with vista I delted the vista partition and resized the xp partition back to it's original size. I am now stuck with the windows vista boot loader which persistantly telling me that the windows vista files are not present etc. etc. Is there any way that I can delted the vista bootloader and go back to using the xp bootloader?
Vista used to boot up very quickly. Now it spends ages on the page with the "loading" bar. Is it performing some sort of CHKDSK during this time? I only have sidebar and rocket dock starting up, and it's fast again when it gets to the desktop, it's just that loading bit takes quite an ages, and it didn't used to. Virus/spyware/malware free. How do i find out if it's doing some sort of chkdsk at boot?
I have more or less completed all the driver upgrades and windows updates but I keep getting repeated boot failures of Vista. I can always get into Safe mode but in Normal mode the boot fails just after the first spash screen at the point when the screen goes blank to be replaced by the small circular Vista logo. After 2 or 3 attempts it succeeds to load but then the problem seems to reoccur, particularly when I have been back to XP for a while.
I had a similar problem with XP but that seems to have sorted itself out. I have tired looking in the logs for faults and failures but no clues there. I am running an ASUS P5E MB with Intel Quad 6600, 4Gig RAM, GeForce 8800GT and 2x250Gig HDs.
This is the best install I have ever done (or was)…I did a fresh install and followed a tweak which was to very enlightening, to say the least. From there I have been to a few other sites and moved on to fully customizing my desktop/login and……well…this is where I stuffed up…My BOOT screen no longer works properly, even with the original “winload.exe.mui” file replaced.
I downloaded and used “Vista Boot Logo Generator” I loved the results on my last install…It worked well. Upon deciding to do a fresh install with Tweaking in mind, I simply coppied over a Boot logo I made previously after allowing permissions and all that as well as changing the NO GUI in msconfig…ect….BUT......
i am new to this forum but i have problem with my system bootup. my system takes too long to boot and it started 3days ago. it takes about 120secs at bootscreen alone. i believe it is not my start up programs as it takes about 3 secs to start up from login page. i donot use any third party bootscreen. normally, my system boots in 30 secs but now i am facing a lot of problem which i do not understand. i have tried all the tutorials in this forum relating to bootup problems but found no luck.
XP is on 1st primary partition [active] and is old. Vista is on 2nd Primary partition and is new. Dual boot info, I believe, is all on the XP partition. Soon I will want to go to Vista only. Do I just delete the XP partition (after imaging it, of course!) and set Vista partition to active? (Paragon Partition Manager). Will it then automatically boot into Vista (which has no boot.ini)?
I've had Vista x64 installed for about 2 full months now and I've recently begun having a lot of problems. One being: 187 seconds. What the hell? Before you ask, here are my specs. Lots of fast memory, a fast processor, 7200RPM boot drive (not listed), and ****ing awful performance. What gets me is that the delayed boot time is before I even see the "Welcome" screen.
My current boot time distribution: 1. BIOS does all its fancy stuff very quickly (about 6-7 seconds or so) 2. I get to my boot loader and it defaults to Vista after 5 seconds (dual-booting Vista/Ubuntu). 3. I then see the Vista loading screen (black screen with green loading bar) for about 4-5 seconds................
hp tool ask to do this "Then please go to “using DOS system files” column and add the link to where you stored the unzipped DOS boot up files. "so my question is , where can i get the "dos boot up files" for vista64? with the hp tool i need to locate the dos boot file address . so how do i do that? do i have to download vista64 boot files? every google links explains how to do this with xp. couldnt find any for vista. makes me feel like im the only person on the planet using vista.
I have installed Vista on my C: disk. After that I installed XP on D: disk. Now I can't boot Vista anymore. I tried with boot.ini. I've read that there's a program called bcdedit.exe. I tried to make that one work on XP, but I failed. I don't have Vista's DVD, and I'm trying to avoid installing XP again. If there's any way around...I would be gratefull! (Is there any way I can edit bcdedit.exe in XP?)
I was running dual boot fine between XP and Vista now im running both Vista it only reads my newly installed drive on boot and i have no boot options as you do in XP/Vista installs, im a newbie to dual drives and was wondering how to set it to have boot options now!
I searched all over the internet for this simple (I think) problem, but I couldn't find any solutions. I have installed Vista on my C: disk. After that I installed XP on D: disk. Now I can't boot Vista anymore. I tried with boot.ini. I've read that there's a program called bcdedit.exe. I tried to make that one work on XP, but I failed.
I once read a post about a boot menu reappearing on every boot. Did a seach on google and found as the 10th result the post I needed (i recognised the text in the preview shown). Search on google 'site:www.microsoft.com boot menu'Found:But......that thread no longer exists. Also I cannot find that post again.With this post result? With a boot menu reappearing?
I have a HP pavilion laptop which came with 64 bit vista ultimate pre-installed. I shrinked the OS partition (160 GB), created new partition (40 GB) for 64 bit windows 7 ultimate. After installation of Windows 7, I cannot see the vista ultimate boot option when I boot my PC. When I boot into Windows 7, I still can see the vista partition. But instead of C: it is now displayed as E: I used the HP Recovery Disc to repair windows vista but I can only see a blank blue screen with the mouse pointer. How can I recover the vista?
The other night I was in a rush and I held down the power button until it shut off. the next day I tryed turning it on and after the MB homepage came up for 3 secs on the top left hand corner of the screen it said "Disk boot failure, please insert boot disk and press enter" so i fooled around with the priority settings a little bit and nothing worked. I then inserted the windows vista CD and it would say "Loading windows files" then the loading bar came up and it would always freeze at the same point and after about a minute a blue screen came up saying a problem occured and is shutting off the computer to prevent further damage. Iv tryed everything. could my hard drive be damaged or something? Please someone help me. I cant work with much because i cant even get into windows! :-( All i can work with is the Setup menu
I bought a new pc for my work which has all the bells and whistles. Of course the kids want access to the pc so that they can play the latest games. I prefer not to install any games on the pc. I have a couple of licenses for both Vista Ultimate and XP Pro. Is there any way to install either Vista or XP on a USB drive and install their games on that. When they want to play, they can just boot their drive off USB, making use of the hardware on my pc?
We just bought 2 Toshiba Satellites A200, both run Vista Home Premium. Now one does not boot. Some of the screen messages read:
"Windows Error Recovery" "Windows failed to start." "Launch repair (recommended)"
When we click Launch repair the screen goes to Windows Boot Manager and it reads: "Windows has encountered a problem communicating with a device connected to your computer.
This error can be caused by unplugging a removable storage device such as an external usb drive while the device is in use, or by faulty hardware such as a hard drive or cd-rom drive that is failing. Make sure any removable storage is properly connected and then restart your computer. If you continue to receive this error message, contact the hardware manufacturer.......
After my PC was burned out by lightening through my Broadband connection I received a new PC from my insurers with Win.Vista Business, but I did not received (and will not) the Windows Installation CD.
Whilst setting up the new PC with various matters an invitation appeared for me to make a Windows Recovery disc, but I was too busy with other matters to do it there and then, so thinking that this invitation will appear again I cancelled it.
It is now some weeks and the invitation has not reappeared. Which way can I make the Recovery Disc in case of a crash?