Is is often recommended (if defragmenting tool allows it - as JKDefrag and incoming MyDefrag ) to keep MFT and folders close together for short access time. $Logfile ( NTFS transaction circular log ) seems not to be movable by Vista defragmentation API. Does make sense to keep together all of them by placing MFT / folders toward $Logfile?
View 4 RepliesI have a new laptop with home premium on it....i'm trying to install a baseball game,but I keep getting the same message at setup "unexpected problem trying to create or write to logfile"...error #7 i've tried running the program as administrator and it has no effect. Might there be some other form of security that vista won't allow this software past?
View 7 Replies View RelatedI am trying to restore my computer and it says my ntfs is missing.
View 4 Replies View RelatedI just bought a external hard drive
But, after transfering all my data I found out it is FAT32?
Is there a way I can change this to NTFS?
Without losing the data?
it is drive G
i'm going to format an external HDD: in the mask that appears in Vista i need to choose the amount i want for the size of the allocation file. what does this mean? How this will influence later my HDD storage capability?
View 5 Replies View RelatedI have an internal IDE HDD that I have put in an USB external enclosure and connected to my Dell Vista laptop. When I attempt to format the drive in Computer Management, I assign it a letter and format with NTFS. However, the result is a Healthy Partition in RAW format. When I try to attempt to reformat using quick format, sometimes it will format it again as RAW, or it will give me an error message stating that Windows cannot format the drive. Again, the HDD shows up as a Simple, Basic, Healthy(Primary Partition) with a RAW File System. I cannot access the drive and put files on it.
View 5 Replies View RelatedI want to buy Windows Vista NTFS and I cant find it. I have a small business and I need this program for my Apple Computer. But I cant find on any website what versions of Windows vista has NTFS.
View 8 Replies View Relatedwhen I powered up my Vista I noticed that it was unusually slow and all of a sudden, it froze for no apparent reason. I rebooted [by pressing reset on case as keyboard wouldn't respond] and booted into XP and ran chkdsk on the Vista partition. Sure enough, it found two errors but in the index area. Here's the output of DOS window:
Code: C:>chkdsk /r d:
The type of the file system is NTFS.
Volume label is NEW_C.
CHKDSK is verifying files (stage 1 of 5)...
File verification completed.
CHKDSK is verifying indexes (stage 2 of 5)...
Deleting index entry SBEServer.exe in index $I30 of file 1153.
Deleting index entry SonicMCEBurnEngineIcon.png in index $I30 of file 1153.
Index verification completed..................
on my Vista Ultimate I have just create another user account, (for a friend of my) how is only members of USERS on my HDD E: the security rights are those:
Authenticated users = ~Full control
SYSTEM = ful control
Administrators = full control
Users = Read & execute, List folder contents, Read,
but with this new account I can still remove thing on E: (the security settings of the delete test file are the same as the root Disk)
I just ran the vista advisor from Microsoft and it said my 160 GB FAT 32 Hard drive was acceptable. I was under the impression that Vista required NTFS. I don't like the convert command because it loses some performance and has other issues. I can format and partition another 160 GB Hard Drive to NTFS and then use Acronis to copy partions (it will copy the files from an image without copying the FAT 32 format). The only problem is that it will take more than four hours. Does anyone know of a quicker method?
View 4 Replies View RelatedCan vista 32 pro install on an ntfs partition formated with 16k clusters. If so how can I format the drive to 16k clusters using the vista boot cd, are there any steps or commands I need to do during the boot sequence? And are there any "stable" third party programs or suggestions so I don't have to dump the current os that is on the drive? As I believe that the image file restores the cluster size.
View 9 Replies View Relatedi have linux ubuntu 8.10 and im changing to vista when i boot from dvd and get to choose partition part i click format drive and it sais error 0x8004005. partition needs to be NTFS. how do i make this partition NTFS and format it so i can have vista?
View 6 Replies View RelatedI am used to dual booting xp O/S and typically I keep one partition NTFS (everyday usage) and the other FAT32 (software testing). This is so when I boot into my FAT32, my NTFS is hidden and the primary drive is C:
I bought a new desktop with Vista intalled on it, I have successfully partitioned and dual booted with XP. Vista is NTFS and XP is FAT32, when I boot into the FAT32 XP, the primary comes up as H: and the C: is still the Vista partition which
easily browsable? Why can XP read Vista NTFS partition?
Can vista 32 pro install on an ntfs partition formated with 16k clusters. If so how can I format the drive to 16k clusters using the vista boot cd, are there any steps or commands I need to do during the boot sequence? And are there any "stable" third party programs or suggestions so I don't have to dump the current os that is on the drive? As I believe that the image file restores the cluster size.
View 6 Replies View RelatedI have an eSATA drive formatted NTFS from my XP installation. Drive works fine from either XP or Linux (multi-boot machine) I had previously tried Vista on the machine but it saw the eSATA drive as unformatted. Gave the message "Do you want to format this drive?"
Very dangerous as an unknowing person may have actually formatted the drive and lost all their data. Interestingly enough, any time I've tried to access the drive, Vista ran a chkdsk on it at the next boot up. CHKDSK from Vista saw it fine and reported no errors. but could not read the drive once booted to the desktop. I eventually gave up on Vista and just did a Win7 install yesterday.
It's a new drive with nothing on it. I started converting it from an Amin command prompt about 5 hours ago. The LED on the drive is flashing and the Task Manager shows it's running but other than that I have no indication that it is in fact actually running. Below is what the command prompt window displays. It has not changed at all in the 5 hours. Has anyone else experienced this? How long does this process usually take?
Windows is verifying files and folders...
File and folder verification is complete.
Windows has checked the file system and found no problems.
624,976,672 KB total disk space.
160 KB in 5 hidden files.
32 KB in 1 folders.
32 KB in 1 files.
624,976,416 KB are available.
32,768 bytes in each allocation unit.
19,530,521 total allocation units on disk.
19,530,513 allocation units available on disk.
Determining disk space required for file system conversion...
Total disk space: 625129272 KB
Free space on volume: 624976416 KB
Space required for conversion: 843485 KB
Converting file system
Recently, after varying times of general computer usage (internet, e-mail) ranging from 5 minutes to an hour, I'll get a BSOD, with the above title. I'll attach the dump files, and include the code from it below. I've tried some troubleshooting of my own. I've run memtest86+ on each of my 4 1-gig RAM modules, all clean. I've run Prime95, clean. I've installed new video drivers. I've run a diskcheck, and used Western Digital's diagnostic utility, clean. The culprit always is ntfs.sys. Should I try to repair my windows, or replace the ntfs.sys with a new one?. Also, I don't have any readboost of USB storage devices plugged in.
Code: PAGE_FAULT_IN_NONPAGED_AREA (50) Invalid system memory was referenced. This cannot be protected by try-except, it must be protected by a Probe. Typically the address is just plain bad or it is pointing at freed memory. Arguments:
Arg1: fffffa610b3a9ff8, memory referenced.
Arg2: 0000000000000000, value 0 = read operation, 1 = write operation.
Arg3: fffffa6001219130, If non-zero, the instruction address which referenced the bad memory address.
Arg4: 0000000000000005, (reserved) ............
I know about FAT32, but I know little about NTFS. Assuming both hard drives are not "fragmented". If a large (200MB) file is deleted, is it more likely to be overwritten (space it occupied on the hard disk is overwritten) on a FAT32 hard disk compared to a NTFS? Remove "ine" from my email address
View 4 Replies View RelatedI am runnig out of space in the C drive, but have plenty of space in D drive. How do I allocate more space from the D drive to the C drive? As you can see I have no memory in C:. What can I do to increase it? Do not want to purchase additional programs, not enough space to install them.
View 7 Replies View RelatedWhat happens when you attempt to install Windows 7 on a drive with NTFS version 1.2 (or some earlier version... like 1.3, etc)? Does it alter the file system? Any way to force Win7 to use the older file system? I'm hoping for performance improvements due to less features in older NTFS, but I know little on the topic.
View 6 Replies View RelatedIn my Event properties I getting a NTFS error that the file system structure is corrupt and unusable.
It tells me this is volume Device Hard disk Volume3
Question is, Which hard drive is that?
In disk manager I have the following
Disk 0 F: drive
Disk 1 D: drive
Disk 2 C: drive
Disk 3 H&P: drive
Disk 4 G: drive
Disk 5 M: drive
I guess that's kinda messed up..huh!
plus other removable cf card / sd card / mmc card drives
I need to Chkdsk the volume3.
I have just spent all day, literally, formatting and partitioning my 500gb SeaGate Free Agent. As of now, it is 32gb FAT32, and the rest is NTFS. My question is, can I use the Extend/Shrink Volume tools to decrease the maximum capacity of the NTFS format and therefore increase the maximum capacity of the FAT32 format, as I need more than 32gb. If not, how can I achieve this on Vista?
View 4 Replies View RelatedAwhile back I was given instructions on how to change the folder standard green folders to new pink folders. Well, my computer crashed out and I had to get a new hard drive. I tried to follow the instructions from the previously solved thread, but I can not find the "desktop.ini". When I go to the users folder inside my choices are Administrator and Public and I can not find the "desktop.ini" file. I have windows vista.
View 8 Replies View Relatedi have two folders in my startup menue that i want to delete:
Autostart
Verwaltung
i tried to delete them (right click > delete). but when i restart my computer the folders are there again: how can i get vista to stop renewing those damn folders.
I love the personal shell folders so much I would like to create extra folders
View 9 Replies View RelatedHow do I share a folder and all its sub-folders and files? When I enable sharing on a folder, I cannot access it from my XP box. I see it in the network but I cannot access it. I turned off Password Protection in Vista.
View 9 Replies View RelatedI am just configuring Windows Mail in Vista. In Outlook (on XP), I had multiple email accounts linked to different folder structures. Each account had a different set of folders. In Windows Mail, it seems everything is being downloaded into one Inbox. Can I re-create the separate folders for each email account in WinMail?
Also, my gmail accounts folder structure was synchronized with the folder structure on the web using IMAP. Can I do that in WinMail, too? If so, how (or point me to directions)?
I have just recently started having a problem where I cannot name or rename any folders in vista. When I rename or name a folder it looks like it will work, but then it just reverts back to being named 'new folder'.
I've looked all over the net, but can't seem to find a solution which works.
I've just noticed that the following folders have disappeared: sent, deleted, drafts & outbox.
View 9 Replies View RelatedHow can I get rid of the public folders for keeps. I don't use them and they are interfearing in my other programs. Well , I guess they aren't interfearing with the programs. The Kodak easyshare software I use insists on putting my pictures in the public picture folder. I don't want anything public on my pc. Any way to corect this?
View 9 Replies View RelatedAfter a month or two honeymoon with my new computer last summer, Windows Vista quit letting me create new file folders!!! This is really, really annoying, needless to say.
The other thing is that Windows Vista crashed this weekend and lost some of my files - and the start menu quit working. I think some of the indexes got screwed up or something. I don't know what brought this on except that we had a couple of power failures - and the machine doesn't seem to run chkdsk automatically on restart. If I started the machine and walked away and didn't see the prompt, then I've been using a 'dirty disk' for a week or two and it finally crashed. Or I also installed wireless networking. Also Windows Update downloads automatically and could have downloaded something incompatible with my software. So who knows what might have caused this .I couldn't restore either - now if I ask for Windows restore, it comes up
with an error message.I've been using DOS and windows machines for 20 years and I've never had this happen to me before. I've always had virus checkers and been conscientious about backing up my data.