submits their ideas and suggestions about this problem i'm having. Well here goes. I just recently reloaded my computer with windows xp and now everytime i put a disk "just about any disk" into my cd-rom my monitor will go blank. It acts "the monitor that is" like it gets unplugged from the computer. The pc is still running.
View 14 RepliesI have a old Dell computer which I brought a 24" Dell HD monitor. I upgraded it with a new graphics card which has both VGA and HD capability hook-ups. Now we have a new tower to go with exisiting 24" monitor. My problem is I can not get a old standard VGA monitor to work with the old system listed above. When I plug in the the VGA monitor plug in the VGA outlet in the old computer I get no signal to the monitor. What do I need to do with drivers or other wise to get the old computer back to being able to be used with the old VGA monitor?
View 2 Replies View RelatedI recently did a XP reload. Now, standby is greyed out. I reloaded the graphics driver with no change.
View 2 Replies View RelatedAfter two weeks of fighting, I finally got our lap top to reformat and Reload XP Home. I have followed the steps on re-installiing XP that was posted several times, my problem is it has been "stuck" on the wallpaper screen, with the bottom task bar loaded and the recycle bin icon present. The light indicating the drive is busy has stayed on and I can hear the disk moving. Does it normally take an hour and half to get this far after pressing the " finish" button on the install?
View 6 Replies View RelatedThis is an IBM think center with XP Pro. Symptons are random shutdowns and restarts, and constant freezeups. I checked the power supply and it smelled like it was burnt so I changed it. I replaced the HD with a new 40 gig Hard Disk and when I went to load OS it got as far as "checking system configuration and then it freezes. I cant format or reload OS.
View 4 Replies View RelatedI just moved in to college and set up my computer, but due to limited space didn't bring my second monitor. Now my aim, and ventrilo windows are still on the other monitor but no way to get them to the current monitor for use.
View 2 Replies View RelatedI started out having a trojan or a virus that kept me from being able to do much on my computer, and I was running VERY slow. So I tried doing a Restore point and that did not do, because my computer could not find a restore point it could work from. I had several, but I would get an error message saying I could not use that restore point. Anyway, I then decided to reformat it. After I did that, my monitor started acting up. It has NEVER done this before... It would be on, and I would be computing right along, and all of a sudden my monitor would just go black! Then it would completely log off. I would get a message saying there was no connection. It never did completely turn the computer off (like some errors usuallly do) it was JUST the monitor, but I could not get the monitor to come back on unless I turned the computer off myself and rebooted it. I did a reboot and it worked for about 30 minutes and then started doing the same thing all over again, but this time it would only work about 10 mintues then shut down the monitor. I would reboot and the same thing would happen over and over again.
I went to microsoft online and looked for the Windows XP downloads and decided to try and update anything I needed. It did all the updates and said I had something that was damaged and needed repaired so it fixed that problem and I tried it again after the reboot. Still nothing helped the problem.My DH first thought it may be the video card. He opened it up to check and found it was very dirty and dusty around the fans etc.so he cleaned it, hoping that may have been the problem and put it back together. I tried it again and got the same thing! NOW, it will work about 2 minutes before it turns itself off! So tonight he is going to try a different video card in it and see if that helps...if not he said it may be the motherboard. Do you have any other suggestions as to what may be causing this problem? I am at a loss myself.I have also ran my ZoneAlarm Suite, nothing picked up, McAffee, found nothing, AVG found nothing, I did a disk defrag and that did not help either. I uninstalled all the antivirus and antispyware and still did not help. I now have only the McAffee running on it. (By the way I did not have all the antivirus programs running at the same time, ever.)
When Windows adds a new monitor using the standard driver, can it detect the aspect ratio? When I hooked up mine, all the resolution choice were for 4:3 monitors. There were no widescreen options. It should choose the monitor's native resolution on its own if the monitor is an LCD.
View 2 Replies View RelatedFirst time user, and at my whit's end with my computer. Bear with me as my computer knowledge is very limited. I have a Gateway 2.8 GHZ celeron with 1GB of ram. I also have a Radeon Video Card (forgot the exact model). I went to activate my computer from standby mode and it would not come up. I did a hard reboot and when windows came back up it was real slow and the computer monitor did not "turn on" until it entered windows. It seemed to be in safe mode. No icons were available on the desktop and the background I had was reduced in size and surrounded by the basic green background color. The other colors are also screwed up, the seemed very basic. I was able to get McAfees to come up and am currently running a virus scan. The start button with it's options is available but with very limited use. I tried a system restore, but the window would not appear. Whatever I open seems to open the window on the far left side of the screen beyond the reach of the mouse. Bottom line is the computer is, for the most part, inoperable.
View 14 Replies View RelatedI don't know what's going on... so Im not sure if I post this here.I was watching a video clip online, and got a instant messege and suddenly everything froze. I could move my mouse. And then My computer started Beeping like hell. it wasnt one long one, it was alot of fast beeping. I clicked my mouse a few times, and the beeping stop. Then my screen started glitching. something flashing across the middle. What the hell, this hasnt happened before. Can anyone tell me what's going on?
View 2 Replies View RelatedI dont know if this is in the right Forum as its a strange one.Just before i was playing on Counter Strike and the computer crashed.The power was still on, on the CPU, and also on the Speakers and Monitor.But the Monitor isnt picking up the Computer, ive tried a different monitor but to no avail.Ive basically just swapped all the wires over from the computer onto one of my old computers which im on now, and there was no problems what so ever.So clearly its something wrong with the other computer, but it still powers up and is running, but just nothing appears on my screen
View 7 Replies View RelatedI just had to reinstall windows xp on my computer because of viruses. Everything went ok. This morning I tried to change the display resolution apparently too high. Or maybe the driver wasn't updated or something. Anyway, the computer starts booting up but then brings up the message 'Attention Out the Range H:72.00kHz V:72.00 Hz'. I booted into safe mode and deleted the account where I tried to change the resolution but it still won't get past the bootup screen before giving the frozen up attention message.
View 6 Replies View RelatedI have a new emachnies T6528 computer hooked up to a "Balance digital technology" 17" LCD monitor.If I go to start, shutdown, and then restart, the computer will restart fine again and again. However, if I go to start, shutdown, and "turn off" and shut the computer completely down, then hit the computer power button to start the computer a few hours later or the next day, the monitor says there is no signal. I tried turning the monitor power button on and off. I also tried moving my mouse. The computer does not seem to start or do anything and the only way to turn it off is to cut the power by unpluging it or turning off the switch at the surge protector. Just pushing the computer power button will not turn off the computer when this happens.I checked the cable connections and they are good. For some reason, after cutting the power and turning on the computer again a second time, it works. I have been through the scenaro several times and it works the same way each time.
View 13 Replies View RelatedFollowing a recent change of monitor my computer now hangs at the windows logo screen. It also hangs during startup in safe mode and when trying to boot fromthe windows CD.
View 6 Replies View RelatedI am trying to go from a single monitor to a dual monitor. My present graphic card is integrated on to my motherboard. I have another old graphic card a PCI S3 Virge. The problem with this graphic card is that its driver is not supported by Windows XP.If I disable my graphic card on my motherboard.I can manage to get
this PCI graphic card to work.If I hook up both the graphic cards i.e. both of them are enabled,the computer does not manage to boot (except in safe mode.) It should also be mentioned that when my PCI card is plugged in the computer at time of booting uses it and not the monitor plugged into the graphic card attached to the motherboard. Is there a way to change this.I tried messing with i.e. all possible combinations of values in the BIOS, but nothing seems to work. I would be grateful if someone had some idea on what to try.
my darn gateway monitor screen is too wide. How do i reduce it to the regular size? I pressed Ctrl and held down on the scroll lock and nothing happens. i tried to reset it with the monitor button but nothing happens.i can not view the right side graphic on my monitor
View 8 Replies View RelatedFor the past 4 months, sometimes the computer doesnt shutdown properly. the computer power stays on but the monitor isnt detecting any signal from the pc. along with this I sometimes get a BSOD when shutting down stating that its caused by mv61xx.sys and the error code is 0x08E. I dont know why its doing this
View 14 Replies View RelatedI inadvertently disabled the monitor on my desktop. Now, of course, I can't use my monitor to get back in and enable it. I've tried to restart the computer in the safe mode by tapping the F8 key when turning it back on to no avail
View 4 Replies View RelatedThe problem that I am having is with my HP Pavilion XT983 Desktop Computer. It will not boot up when I power it on. The power light is on and the monitor is in sleep mode. The only thing that is operating is the fan. I have tried rebooting with the boot up diskette but it is not reading my A: drive. It also will not read CDs.
View 6 Replies View RelatedI replace my old LCD monitors (Dell 1905s) with new acer P223w's. I have a dual monitor display.I power off both monitors with one switch that cuts off the power. When I do this however, Windows makes the sound like a device has been disconnected and it messes up my monitor settings. This is very annoying and it didn't happen with my other monitors nor does it happen on my other Windows XP system with different monitors. It's like Windows is trying to be "smart" by thinking the monitor is gone. I do not want Windows to care if the monitor is powered off.
View 5 Replies View RelatedI wonder if it is possible to switch off the computer's monitor manually.
System Control / Energy provides the possibility to define how long the
computer must idle to disable the monitor. I want to do that "by hand". Is
that possible?
I've got an HP notebook with Windows XP. I just went out and bought an s-video cable so I can use my TV as a second desktop, but I can't get the damn thing to work and now I want to kill. Here's what's happening: when I go into display properties and screw around with the 1 and 2 monitors and try to "extend my windows desktop", my monitor turns off for a second and the TV blinks like it wants to work, but then the monitor turns back on and the TV just stays blak. Same thing happens when I do the FN+F5 thing.
View 2 Replies View RelatedIf I was to purchase a new PC, could I attach it to a old windows 98 monitor i have. If so is there some PC's that would work better then others and about how much could it cost?
View 1 Replies View RelatedI have a Gateway computer that’s about 4 years old running Windows 98. It includes a Gateway VGA monitor (model EV700). I had to reformat the hard drive and reinstall windows using their resource CD’s. Everything is fine now except the monitor will only display the lowest resolution settings. I have tried to change the resolution through the display icon in control panel, but it will not allow me to increase the resolution. I have even gone to the Gateway web site and download the latest driver for this monitor, but still have the same results.
As a result, the monitor will no longer display graphics of any kind while on the internet or while working with photo imaging software.
My PC has just a VGA port. How can I setup a dual monitor?
View 7 Replies View RelatedI cant get a monitor to install on pc winxp it said vga not compatible i dont have disc know that xp has this driver but i read that i have to trick it into using it this i got from internet dont understand it it is a tft monitor proview i have been to the sight but cant find which driver it is!
View 49 Replies View RelatedMy computer is having some trouble. When I try to boot it up I get nothing from the monitor(LCD). This happened a while back and all I did was took the power cord to the monitor out, and plugged it back in. It worked like that for 2 months or so. Today he calls me and he is having the same problem. So again I unplugged the cord and replugged it back in. I got signal but it immediately went blank again. It will only work for 1 second. What could be causing this do you think? I hooked up two other monitors to his computer also. One of them (older one not sure if it works 100%, wouldn't see why not) would BOOT up fine, then once you got to login it would go black, and do exactly what the LCD did. I could unplug it plug it back in for some video. Then I brought over my monitor. It works 100% and I didn't get any video at all with it. I tried other power cords/outlets etc. What do you guys think it could be?
I am trying to hook up an external monitor to my lap top I can get my background to show up but no icons
View 3 Replies View RelatedI have an older IBM 10in screen thinkpad running Win2000. Turned it on for the first time in a while the other day and the windows sign on screen is off the right and it is like I am on dual monitor. Can slide pointer to right and get to one side with startup menu then slide pointer back to left for icons. When put a screen saver on in tile mode, it duplicates it side by side but you have to scroll left to see both. Have gone into display and tried to change things but nothing works. When I go to settings, it shows only one monitor but says display [Multiple monitors} on silicon Motion LynxEM+.
View 3 Replies View Relatedwhen I turn on my pc, the monitor doesn't show anything at all. I have no idea what casue the problem. Even I have the video card replaced, it doesn't solve the problem.
I don't think is the monitor problem as I tested the monitor from other pc and it works perfectly.
I'm running windows Xp and i shut down my computer and restart it like your supposed to and then when i restart my monitor is blank yet i can hear all of the sounds of start up. So i shut it down again and i still come up with a blank screen and now i'm using a external monitor to view my desktop. Now when i look at my laptops monitor i can vaguely see what i'm doing at all and the external monitor is fine. Also my laptop is creating alot of heat.
View 5 Replies View Related