Reboots At Shutdown - NO ERRORS - Phoenix Bios Have ACPI On?
Sep 24, 2006
I have just: Done a successful repair/rebuild of XP Home Did a CHKDSK /r/f on my System drive Defragmented my system drive with PerfectDisk Read and applied recommentations on changes so that I would see errors when my system re-boots Yet, When I shutdown my PC, it will shotdown, then re-boot again, without the benefit of a error messagw to help me figure out why it is re-booting instead of shutting down and powering off. Is there something wrong with my Phoenix Bios have ACPI On? What can I do to see error/warning messages on why my system re-boots when I shutdown?
Windows XP Home Edition Service Pack 2 (build 2600)
2.08 gigahertz AMD Athlon XP
128 kilobyte primary memory cache
512 kilobyte secondary memory cache
Board: ASUSTeK Computer INC. A7N8X Deluxe
Bus Clock: 166 megahertz
BIOS: Phoenix Technologies, LTD ASUS A7N8X Deluxe ACPI BIOS Rev 1009 09/27/2005
1024 Megabytes Installed Memory
Slot 'DDR1' has 512 MB
Slot 'DDR2' has 256 MB
Slot 'DDR3' has 256 MB
NVIDIA nForce2 ATA Controller (v2.6)
Graphics Card ? ATI AIW 9600- XT ? AGP
I just opened this computer I got from tigerdirect.com and I was loading windows 2000 pro onto it...It loads half way and I get this message:
ACPI Bios not fully compliant with the ACPI specification.
So I did what I read and When Setup starts again, press F7 (not F6) when you see the "Press F6 if you need to install a third-party SCSI or RAID driver" screen.
Windows automatically disables the installation of the ACPI HAL and installs the Standard PC HAL.
So win2k is installed but I cant seem to get onto the internet and update any of the drivers.
THe computer is a IBM netvista 8307 model. They had some deal on it awhile back for less than $150..so I couldnt pass it up.
Im kinda lost right now..not sure what the problem is.
I did add a new video card before I installed the OS. could that have been the problem? If so..how would I go about fixing this.
We got a hand me down gateway for daughter and we had to reformat the hard-drive. I came to find out was missing the third disk on Gateway's "System Restoration Kit" disks. They no longer provide them anymore, since out of warranty. I was going to just install full version of XP (just had Win ME, when reformatted). It's telling me "No Hard disk error". I tried going into BIOS, hitting F10 on boot up. But there's no Sata settings in my bios. It's a "Phoenix Bios" system.
I am running XP Pro on a laptop loaded with programs and files.When I recently started it up, instead of loading with the familiar Compaq logo, it started in a DOS program (Phoenix BIOS) with a warning that "it had not been shut down correctly last time." I think I did shut it down correctly last time. The BIOS offered me two options. 1) Hit F1 to Boot or 2) Hit F10 to continue. I hit F10. That took me to a screen where I had to guess what to choose. Did I want to Save and Exit? Did I want to Escape and abandon changes? etc. I didn't know what to do but it seems I had not made any changes so I said "abandon changes and boot
Formated the drive, installed XP, it re-booted to continue the installation and then it hangs on a BSOD saying that my BIOS is not fully ACPI compatible. I am using an SATA drive. Specs: ASUS A8n-SLI 16 Deluxe, AMD 4200+X2 64 Dual Core, 250GB WD SATA drive, 2GB corsair 3200c2. I am thinking of just turning acpi off and then putting it back on once xp is on.
Have two brand new Dell OptiPlex machines with WinXP Pro that reboot when you do a shutdown. They go through the normal shutdown and then start booting again. I've tried everything I can find on the web about power management settings and such, and have contacted Dell who ultimately recommended reinstalling the OS.Would anyone have any other recommendations before I take the drastic step of re installation? The machines have a ton of production software already loaded that will take hours to reinstall.
Alright so heres the issue, I had aquired a Trojan-spy.win32@mx. And i went through the process of deleting it. Which was quite long and annoying. Now however my computer randomly decides it feels like rebooting. Ive ran Chkdsk /f, and even did a non destructive restore. And nothing has helped, so im stuck here in safemode till i can get some help. Best buy wants to charge me $129 dollars to fix it, but who has that kind of money for them to run a few things? SO please guys if you could help it would be great.
When I went to start up my computer (HP Pavilion 750n, 768 MB RAM, 1.6 GHz Pentium 4 processor) yesterday, there was no power. I took it to the local repair shop. The tech said it was the power supply again (the second one I've had in 6 months). He replaced it with a non-HP power supply. It boots up and all the programs are functioning, but when I do the START>SHUT DOWN>SHUT DOWN, it just reboots. I did some investigating and found a work around for this (right click on MY COMPUTER>PROPERTIES>ADVANCED tab>STARTUP and RECOVERY SETTINGS>unchecked AUTOMATICALLY RESTART under SYSTEM FAILURE). I'm still concerned about why the icons in the SYSTRAY can't be hidden now.
I am desperate now, this problem is so annoying. Since upgrading my bios, I have not been able to shutdown my PC without it restarting automatically.I have tried so many things to correct it but to no avail.
I just purchased a new Dell Dimension 9100 (new line for Dell). I loaded Mcafee VirusScan, Firewall and Privacy Service and then downloaded updates for all of the preceeding Mcafee programs (there were many). I also downloaded all critical Windows Security downloads. Everything is working fine except when I work with wordpad/notepad/word or other Microsoft programs. At random, when I open these files, I recieve IE shutdown errors. I created a new wordpad and notepad file, saved both and re-opened them: everything seemed fine. Then I ran Windows Explorer and when I tried to open the wordpad file with explorer, I received IE shutdown errors.
while composing an email i suddenly got this " Phoenix Technology" Recover pro msg. "Operating system or hard disk partitions have been altered. The current restore point does not match either your current hard disk setup or your OS" I am unware that i have any Phoenix hardware install. I have win XP ver 5.1, i have not installed any new hardware, or partitioned the disk, and everytime i close down the system this msg appears. The main start-up screen and desktop reappears after "ok". need advice. email is hmcdoc77@comcast.net
I messed with some setting in the window for display properties>screen saver>Power Option Properties. Don't remember what I did, but the next time I restarted the comp. it loads windows then immediately after the startup screen goes away it says it's going into hibernation and does.It will stay on in Safe Mode, but the checkmark that tells hib to be on or not is not there. I've tried disabling ACPI in the BIOS but that doesn't fix it.There has to be some setting in the registry that can be changed to disable hiber, but no one seems to know how.
I have configured the powermanagement of my Windows XP clients (XP Prof. SP1 and SP2). I have setup the computers to enter standby after 1 h and hibernate after 2 h. The clients successfully wake up on LAN traffic.I would like to monitor the standby, hibernate and wake up events in any kind of event log.
Here is an easier way to do the Fresh Install with no ACPI. When setup is loading, the blue screen will ask if you have any raid devices, and to press F6. When it does that, press and hold F7, & Congratulations! No ACPI will be installed.
I accidentally formatted over my XP installation (should...have...used...gparted....not...partition...magic...) about a week ago. Fortunately I keep my files on a seperate partition. I put in the XP disk, and install as normal. Good, it reboots. XP logo shows for a split second, then..."Motherboard does not have ACPI support...blah blah blah http://hardware-update.com blah blah blah". Fine. Restart setup, in non ACPI mode. Reboot. Yay it works. Install videocard drivers, reboot. Now it just restarts after showing the XP logo for a split second. Damnit! Put in CD. Reinstall. Forgot to put on non-ACPI mode, get error again. Damnit. Restart install in non-ACPI mode....BAD_POOL bluescreen. Slam head on desk. Insert ubuntu cd. Install ubuntu. Go to techguy. Make post about XP install issues. Ask for help.
I'm going to a massive LAN party this weekend, and having XP would be nice, because I want to play Counter-strike, and not just UT and Doom. Thanks a bunch. Oh, hardware specs, right. AMD 4800+ 939, ASUS P5ND2 Platinum (or something) SLi, nVidia 7800 GTX, 1 GB 2-2-2-5 OCZ RAM, Antec NeoPower 480, 200 GB HDD, Linksys WMP54GS (stupid ubuntu not having ndiswrapper installed by default, stupid ndiswrapper refusing to install under ubuntu...), Creative xFi XtremeAudio.
I installed a fresh copy of WIN2000 on my IBM Thinkpad A21m but I am having a problem setting up a device in Device Mangager. I have no idea what is going on.
When i reboot the laptop it prompts me that it has found a new piece of hardware and it wants me to install the driver for it. The problem is that I have no idea what device it is since all the devices that should be working are working - so i don't know what to do. The clues that I have noticed that might help:
- the laptop takes a LOOOONG time to boot up (3 or 4 mins), and is sort of sluggish in operation (compared to how it ran when i bought it)
- my internet connection is super slow ( I have a DSL router that serves 3 computers incl. mine, the other two have XP and everythign runs smooth)
- the unknown device says it is located on the the "Microsoft ACPI-Compliant Embedded Controller"
Would any one know what Device this "Unknown Device" is??? I just need to know so i can install the driver so my system can run properly.
I changed the above setting in my device manager hoping to fix an annoying stutter problem caused with media player when my wireless signal would go out of range. I remembered changing the irq settings in win2k to solve conflicts on that system, but found that the options is not available in xp. A quick web search lead to a site which reproduced a knowledge base article from microsoft. Only, the article was truncated in a way such that the dangers of said action were not published. The drive boots up to the XP OS screen, hangs, blue screens, the end. With my problem drive set up as a slave, is there a way to change the settings back, or manually cut and paste Hkeys, or system folders or the like to restore the drive to it's previous state? Seems logical same computer with the same installation of xp pro sp2
once the on button was pushed, it came up with the BIOS screen asking for the password.I removed the CMOS battery, which allowed me to change the Password so I can get onto BIOS now. However, when I boot now it just comes up with the BIOS screen.I set HD to boot first, aswell as setting the clock and date. I then ask it to save and quit, after which it shut's down, and reboots, only, BIOS keeps coming up. And I need to get this sorted asap
I have had windows XP Pro installed, updated and running fine until about a week ago. I was away from home for about a week and left the machine plugged into the mains but powered down. When I returned home to boot up, it kept doing things like constantly hanging on parts of the bios POST screen, eventually booting up after thirty or so complete restarts. It finally booted into windows but after the last shutting down, it will now not boot up at all. I have replaced the bios battery and reset the bios several times.
When I start the computer, I get a screen freeze and have to press Ctrl,Alt,Del once before any programs will startup. A lot of probs with internet connection and slowness while surfing as well as a lot of pop up ads in my face.
There are system boxes coming up with registry and dll errors and the whole system seems SLOW.
When I turn on my computer, it does the bios check, then goes into the bios screen on its own. I have checked all of the bios settings, and see nothing set wrong. The only way I can get itno my xp pro system, is to use "F8" during the bios check, the select my hd from there, then it seems only half of my programs work, and it also seems to be randomly changing the programs that do not work, when I do this.
Got a bit of a problem with my housemates pc.A friend gave him some extra RAM, i checked it out and it was crucial 512mb pc2100 CL2.5, and although it didn't match his exsisting RAM it seemed to me that his mobo would only run the FSB at 200mhz anyway so i went ahead and fitted it.It worked fine I then noticed his system temp was running a little high (60-65 degrees), so i took his heatsink off and cleaned the dust and refitted it with some new thermal compound.I added too much and the temp went up. To nearly 90 degrees.I shut it dwon as i didn't want the cpu to pop, cleaned it off, reapplied less compound and figured this would work fine.Now we have the problem. Most of the time: Power on and nothing happens. No bios, no beeps. Occasionally: Power on, i jump into the bios, the temp looks fine (30-40 degrees) and then it freezes right there in the bios after about 30 seconds to a minute.This sounds like a heat issue, but the last temp reading before freeze is 33 degrees.?I've double and triple checked that the heatsink is on properly and thats fine. I followed the official guide on how much compound to use (a blob the size of an uncooked short grain of rice).
The family computer is playing up and to the best of my knowledge the computer in question just simply suddenly stopped working as it should. I am unable to get the 'default' welcome screen upon start up and am getting the logon box where you type in a username and passworld. I know how to get rid of this, user accounts>enable welcome screen - but it will not solve the problem.This is just the start of the problems. I get a whole host of errors which popup one after another.
i remote into my XP box everything is fine except when i shut down using a shutdown shortcut and other shutdown utilities no matter what after i get booted off the remote session the computer looks like its shutting down then stays on for a few seconds then a BSOD appear. I have been trying to figure out why for the past week and no solution so im hoping someone can chime in..The problem is only on remote if i shut down locally never a single BSOD and no hardware has changed. No driver issues. ive read and tried all the usual solutions. Need someone here to chime in on specifics.Ive also tried to remote in with bare minimum and no go. same thing.
Im new to PCs and since my motherboard is three years old is it a good idea to upgrade? I contacted the maker of my motherboard and they say an upgrade is available and sent it to me for { DON'T CRACKUP} $49.00. I already read that you can really mess up your PC if you do one thing wrong when upgrading. Am I a fool for buying the upgrade? Please let me know as I can send the Floppy discs back.
I have ibm thinkpad R51 2887 nq2 series .My system has been crashed as it is not starting.The whole system gets hang after showing the first ibm screen. The bios utility setup is not getting opened through access ibm button . In safe mode it shows that system BIOS and video BIOS is not working and it has been shadowed.sometimes the system gets started ,but after one minute ,it stucks and the whole system paused and nothing happens.It may be the virus attack on BIOS and it also changes the time and date configuration of BIOS. so what should i do .And how i can install BIOS driver to the system.
I just flashed/upgraded my BIOS for my motherboard, and now XP doesn't even boot up. After the BIOS load, I get a "MBR error 2" message and it just stays there. My board is an Asus P5N32-SLI SE Deluxe. I used the Asus Update Utility to flash my BIOS.
I am being shown "script error","page error, you may need to change browser settings",and "behind firewall" when I try and send files and photos. I've tried everything I know to fix this, but I still see these errors and still cannot send photos while I'm online.
This is weird. I have to go through the shutdown procedure twice, i.e., Start/Shut Down/Shut Down and click Ok, then Start/Shut Down/Shut Down and click Ok again. It will then shutdown properly. The same thing happens when I try to "Restart." After doing the first shutdown sequence, everything is normal. I can open programs, surf the web, etc. It's as if I never tried to shut it down at all. Only after the second shutdown procedure will it shutdown fully. One note: When I go through the first shutdown sequence, my taskbar pops up and the desktop is darkened. After clicking Ok, the taskbar autohides and my desktop returns to its normal color.I have only had this problem for the last month or two. Before that, all was fine. It's not critical since I can shut it down. It's just annoying to have to do it twice.I have Windows 2000 Pro, SP4, build 5.00.2195.
