I just replaced my old DVD ROM with a new DVD-RW drive. The system writes to the new drive fine (I have burned a couple of Video DVDs) but when I boot the system the Bios says it doesn't see the D: (CD) or E: (DVD) drive. Once I am into Windows XP I can also play CDs from the CR-RW drive but I can't use it to copy new software onto the system.
View 4 RepliesI have an old T1090 eMachine that doesn't recognize the new larger hard drives. I purchased a 200 GB PATA (IDE) drive and it shows up as a 75 GB drive using GParted and under Windows Disk Management. I expected that it would only be recognized as 137 GB, but I can't explain why it only sees 75 GB. I suspect that the BIOS needs to be updated, but I've never done this before so I was looking for a procedure and ideas for trying to find the latest BIOS online.
View 8 Replies View RelatedI don't really understand it.I initially used G-parted to partition my 250gb drive into a 100, 75, and 55.Then I tried installing Windows XP SP3 and it says it doesn't recognize them, so I deleted those partitions and made new ones (the same size though) and it asked me to reboot. After I rebooted it prompted me again with Press Enter to install Windows, so I do and it says some crap about how it doesn't recognize any hard drive plugged in.BIOS recognizes the drive and its size.
View 14 Replies View RelatedMy brother went to My Computer one day and saw that there was no disc drive there, it was working in the past, but now it doesn't show up, I don't think he did anything unusual. But it shows up under Safely Remove Hardware Wizard with "Samsung CD Drive" or something like that.
View 14 Replies View RelatedI'm struggling to connect my Sony Handycam DCR-SR42 to my Compaq Laptop, Windows XP.It works on other computers without a problem that's why I think it must be some setting in XP. I plug it in when prompted by installation software and the camera goes to :'preparing' Then immediately the windows found new hardware creen pops up. On the other computers that screen didn't come up and the camera would go straight into connecting' mode.I tried switching the 'found new hardware' off by disabling the plug and play in'services' with no luck.When I connect the camera while I'm starting up the laptop, it goes straight into 'connecting' mode but unfortunately that stops as soon as windows is started.I would like windows to detect my camera as a drive and not 'other devices
View 1 Replies View RelatedI am running XP Pro on my computer. On another drive I have windows 7. My computer stopped booting to my XP drive all of a sudden, but it would let me boot to my Windows 7 drive. That lasted for about 3 days. Now I can't boot to either drive. When I start the computer it says there is no HDD. I tried to use the XP disk to repair, that didn't work., so I thought I'd do an XP install. But my hard drive doesn't show up all the time. Or it will show the HDD but upon trying to pick a partition to set up XP in, it then tell me there is no HDD. I get the blue screen of death, and have to manually force a shut down. Other times it tell me that the HDD is RAW, and it needs to be formatted. How can I get the HDD to format? Is there a way to do it through DOS. Sometimes I can't even get to the DOS prompt. The bootup section is corrupt. I need to repair it, but can't if the system doesn't see my HDD.
View 8 Replies View RelatedI'm trying to copy some files from my PC, but it doesn't recognize that I've got a dvd burner, it sees it only as a cd burner, it will play dvds, but wont let me erase or burn.My pc has started getting some bugs recently, and I need to hurry to backup my files, before it takes the big crash.
View 6 Replies View RelatedPreviously, my laptop did recognize the drive but for some reason it is now not finding it. I have plugged the drive into another computer and it is recognized. The laptop will recognize other devices which I plug into it. I have checked for viruses and have also tried restoring to an earlier time but no luck recognizing it
View 2 Replies View RelatedWell I have an hard drive into a external enclousure but the windows XP of a new CPU do not finish detect it when I connect it. But the same external hard drive work fine in my laptop. I formated my CPU 2 times, but i got the same error of Windows. My CPU has a new motherboard Foxconn M7VMX-K.
The USB ports work fine with my pendrive.
In my computer i can see a new hard drive with a letter (K, whithout data.
The Windows XP Administrator Disk doesn't show nothing about the external hard drive.
- Taskbar has reverted back to the 98 style
- When I go to Start >> Search nothing happens
- Doesn't recognize the printer that's been installed for over a year
- Won't let me install another one
- System restore gives the error "System restore is not able to protect your computer. Please restart your computer, and then run System Restore again." and restarting does nothing.
I have an old Compaq Presario 5360 with Sis 7001 PCI to USB controller. This machine was working GOOD, I could work with my USB web cam, USB drive, USB digicam and others MP3 players.I have reinstalled my WinXP with Service Pack 2.0 and now I CAN'T use any USB device, when I connect my USB drive this device is not powered, XP doesn't notify me for anything. simply this PC looks not to have any USB controller.I have an DELL Notebook, I can use my USB devices on it.I just reinstalled the OS in the same way how I did it before. I think is something about drivers, the control panel (System devices) tells me everything is good and my USB controllers are working correctly.
View 12 Replies View RelatedMy operating system, Windows XP, comes up with several error messages when I try to open up system files or programs that concern the "Computer Administrator". I then checked in the Control Panel to make sure that my name is in fact the admininstrator, and it is, to no suprise. But whenever I try to open these programs it either says this has been disabled by the administrator. The administrator has turned off this feature.
I don't know why this happens. I find out a way to fix it and then when I close it, it won't let me reopen it without fixing it again. Some programs that I have tried that don't work and give me this or a similar error message are, System Restore, Task Manager, Regedit, and Windows Update.
I have a multi-boot system set up and it Includes 3 OS's, Windows 7, XP, and a flavor of Linux. My XP installation does not recognize hardly any of the drivers for the hardware on my HP pavilion dv2941se laptop. Beings it doesn't have the driver for my network card i cant get online to search for other drivers.
View 2 Replies View RelatedI have a Windows XP home SP2 computer that has a Sony DVD RW DW-D22A that supposedly supports both -R and +R. Well I bought a stack of 100 Blank DVD-R and less than 1/2 way through the stack they turned into lousy DVD's. Both for DVD movies and data storage they wouldn't work. I would get this CRC check sum error message. I contacted the manufacturer and sent in a few samples and they replaced them - sent me two stacks of 50 - nice company. Well I just burned a data disc and my computer doesn't recognize anything being on the disc - I even get the "You have inserted a blank cd/dvd window" thing on my screen. I then tried to burn a dvd movie using a different program and that program doesn't even recognize a disc being in the drive (yes I did put in a fresh dvd before I started the program).
View 6 Replies View RelatedJust upgraded a old pc running win 98 to xp.Before I reformatted and installed the new os I made a backup of my 98 os and files using ms backup on a DVD. The file was about 3 gb and was verified by the backup program. It has the file extension .qic.The XP ms backup doesn't recognize the .qic format.Anyone know if I can install the 98 backup on XP or a freeware backup program to read my file?
View 8 Replies View RelatedI'm running XP SP2 home addition 32 running on AMD64 processor with 1G ram. Most times XP doesn't recognize my Canon i350 printer even though the PC beeps to acknowledge that the printer is on-line through a USB connector. I've reinstalled drivers more than once and even used Plug&Play. Also I don't have any other printer drivers installed. Canon i350 is set as my default printer. Each time the problem occures I can get XP to recognize the printer by either turning the printer off and on again (to easy) and if that fails re-booting sometimes more than once.
View 5 Replies View RelatedI have a USB MICR Reader (It is used for reading checks and credit cards) and i use the accessibilitiy option in control panel to enable serial key devices since the program has to go thru a virtual keyboard in order for the MICR Reader to communicate with the program and in the accessibility options you can only use com 1-4 since MS doesn't reconize anything above 4 for use as a serial device. Nedless to say i need to know how to change com ports in XP the device will take up to com port 18 but the serial devices above 4
View 1 Replies View RelatedI had my wedding pics placed on a CD by the photographer. When I place the CD in a pc running Vista, it pulls up all the pics just fine. When I place it in my home pc though, running XP, my pc acts like there isnt even a CD in the drive, like it doesnt recognize the CD is there at all
View 6 Replies View Relatedmy XP SP2 doesn't recognize my Olympus FE-100. It installs it as "Unknown device". I have no problems this kind with my printer, mp3 player, but i had the same problem when trying to connect my friends watch which has usb memory in it (it works fine on his computer- XP). I tried to connect my camera on Win ME and it works properly. I know this has to do something with my XP, i just don't know what. I tried to uninstall- reinstall the camera, stop-restart the WIA but nothing helped. There is no driver for it because xp should recognize it at least as a storage device.
View 6 Replies View RelatedTried opening a video file that was changed from MSWMM in Movie Make towmv.Previous files opened when I changed them to WMV. This iswhat I get when I try to open file: "Unrecognized format for 'D:Documents and Settings(name of file).wmv'".
View 4 Replies View RelatedI recently was forced to do a re-install of XP to clean up a few bugs.The system has 3 hard drives, but since the reinstall, only the C: drive appears. The other two are nowhere to be found.I've tried mapping to them, but they just don't show up there as a mapping option.Anyone have any advice? When I added the extra hard drives I didn't have an available slot and did have to create a partition. I no longer have the software I had originally used though. Do I need it to make the 2 other drives visable?
View 1 Replies View RelatedI keep getting this error "One of the USB devices attached to this computer has malfunctioned, and Windows does not recognize it". And if I leave my PC on to long the keyboard, mouse, and sometimes even the monitor stop working. I've tried unplugging the keyboard and mouse (which are not USB) and plugging them back in, but to no avail.
View 8 Replies View RelatedEvery music folder in My Music after C (cameo!) has disapeared although I know they are still there - i can still play them in itunes and even open the song folder but if I copy it and drop it back into My Music it vanishes. Windows doesn't even recognise the memory that the missing files use and thinks the folder holds 3 gigs when its more like 30. Just wondering if there is anything I can try before going through the hassle of reformating.
View 9 Replies View RelatedSince XP Pro original doesn't recognize SATA HDs, is it workable to create a install CD using Original XP Pro CD and add in SP1a and slip-stream them together on a new machine having SATA HD?Will this allow XP to recognize the HD and use it well?Similarly, same idea regarding XP HD size limit of 127 Gigs pre SP1a?
Current HDs are so large.How to create such disk ((Tutorial link)?
I'm building a new computer here, and i'm using a previously owned mobo. I'm having an issue getting pass the BIOS spalsh screen and into the boot menu so i could bootup and install windows. I have no beeps at all. every component of this computer is brand new except for the motherboard. I try to go into the setup and i get the dialogue, "Entering Setup..." but it just stays frozen like that.
I know i have to Clear CMOS and i removed the CMOS battery for almost 3 days and nothing at all. i cannot find the CMOS jumper. i see a jumper near the CMOS battery but it isnt labeled clr cmos. i removed it and put it on the 2nd and 3rd pin and the machine doesnt even turn on, but when i locate it back to the 1st and 2nd pin, it turns on perfectly fine, but i still cannot get past the startup screen
the screen i cannot get past looks similar to the image below.
I'm Currently Dual-booting between Windows XP and Fedora Core 5 on my laptop. I no longer want FC5 so I thought I would format that partition to regain my hard drive space. I thought the easiest way to do that would be to boot from my windows CD, but discovered that my System won't do that anymore (I know it used to, because thats how I installed FC5 in the first place). It won't boot from my FC5 cd's either.So I tried to access the BIOS to see what's going on, but for some reason I can't. The startup screen tells me to push F2 but that doesn't work.
View 9 Replies View RelatedWhen I finally finished creating a new Access Database from scratch on my 1 1/2 yr old Acer machine and went to save it to my thumb drive (G drive on the new machine) to transfer it to my wife's machine, I get the message "G is not accessable, access is denied". I had transferred a preliminary version just the day before to my wife's machine using the thumb drive which still works well in her machine.
View 2 Replies View RelatedI have a primary drive (maxtor) whice xp is running on and a second hard drive (maxtor also) which i have been using for some time for storing files. i had windows xp home and everything worked fine for a long while. recently since i upgraded to xp pro, the hard drive icon for the secondary drive disappears from my computer. i even tried saving stuff to the drive from ms word or something and it is not recognized. usually a restart will solve the problem, but after i let the computer run, (till like the next day) it will happen again. i dont know yet what event causes it to dissapear. i sometimes use standby, but i dont think that is consistent with the problem
View 4 Replies View RelatedRunning XP Professional SP3. I am curious why Windows does not recognize an internal DVD ROM as a DVD? It sees it under My Computer as a CD Drive. But, if you put a DVD disc in the drive, then it sees it as a DVD..... THE DVD ROM is an LG Model GH22NP20.
View 3 Replies View RelatedWhen i plug in my pen drive into my computer, i open My computer where i can see it, but when i try to open it, a message pops up saying "insert a disk in unit H:" or something like this. This message usually appears when there is no disk in that drive and you try to open it. but the pen drive is plugged in! not even mac os read the pen drive.
View 2 Replies View RelatedI had to do a reinstall of XP on a brand new HD I just bought and I can't remember how to get XP to utilize my seperate HD I use for storage. It keeps asking me to format it. I have all my data on it so I definatley can't do that. I did something a year ago to get this to work, but I can't remember what I did. I installed XP service pack 2. Anyone know what to do? I remember I did something in disk managment. The drive I can't get to work is used for my backups. It is formatted and partitioned using XP and the same NTFS system as the new HD with XP on it. Even my bios detects the 320gb HD at 136gb max capacity. So its not showing that the drive is a 320gb HD. I am pretty sure my bios specified that it was 320 gigs before.
When I go into disk managment the drive I am having problems says it has 128gb as a primary partition(in blue), but then in the black highlighted box to the right says 170 gb unallocated. Shouldn't all the drive be in blue as being partitioned like it was before I did an install?