Maxtor Hard Drive - Failing In Repairing Damaged Clusters And Segments
Aug 2, 2005
I have a hardrive( Maxtor 6Y200P0) wich have got corrupted and bad segments. (this seme to be a common problem with Maxtor drives) Im almmost sure this drive have psychical damaged clusters, cause i have tested alot & alots of tools that should fix this has failing in repairing this damaged clusters and segments. this includes Maxtor official PoweMax v 1.21, wich fails to complete the surface test. i have got an Error Diagnostic Code=de676679. a code with a 8 numeral should indicate that a Maxtor Drive drive is broken,and is in need of replacement. thats all i know where should i send this code for a real analyz?, cant find anything on Maxtor Website, Another question, there is allso an option to do a Low ore High level formatation of the drive. I have heard that this could fix corrupted segments, If so,this must only be possible on logical damaged hardrives, not psycial damaged drives right? i have waiting with reformatation cause im unsure what type damage the drive have, and this is my last alternative to do.? should i do a low/high level formatation anyway?
I have a Toshiba tablet PC XP2;It boots up very slowly and I have narrowed down issue to two services which when enabled cause the problem.Workstation and Network Location awareness services.When disabled, the machine boots fine. But is useless unless the services are started manually.
I've got an HP / Compaq notebook where the smart diags indicated a failing hard drive, HP shipped me a replacement drive under warranty and I removed the drive and used a couple of notebook hard drive adapters to hook them up as master and slave on the secondary channel of one of my desktops. I then used Ghost to clone the failing drive to the replacement since I really didn't want to have to reinstall all my applications again. The clone completed without any seeming problems however I haven't been able to get the new drive to boot up, the problem is that I just get a blank screen with a flashing cursor and no boot menu, end of story...
I happen to have a Win XP Pro full version CD and I am able to boot from the CD to the recovery console, I've tried the following: Chkdsk /R - Did find and fix some problem the first time around, but didn't find anything wrong on subsequent runs. Fixboot - ran with no problems but still no go. FixMbr - indicated "This computer appears to have a non-standard or invalid master boot record", no matter how many times I've run this and it says it's rewritten the MBR successfully it still says the same thing. In-place upgrade - I've run an in-place upgrade twice and both times it completes and says the system will reboot and the installation will continue but it still gets stuck on the reboot. Following the two in-place upgrades I've rerun all of the previous steps and I still can't get it to boot, nor do I get any type of error message that indicates what the problem is.
My Maxtor External Drive became corrupted and I needed to re-format the drive. Unfortunately, while Working in Windows XP I accidentally deleted the partition and the drive. Now I can't get Windows XP to recognize the Maxtor Drive. I tried re-booting the PC and plugging in the Maxtor USB Cable, but this did not work. The Maxtor Drive was my H: Drive. Can get Windows to recognize my Maxtor Drive? When I deleted the drive I was working in the "Computer Management" Screen. I navigated to this screen through the following path: Control Panel/Administrative Tools/Computer Management.
I have all of our digital photo's on this external hard drive & now I can't access it. When I try I get an I/O device error message. Can anyone tell me how to get back in even once to copy the photo's to my internal hard drive & then burn them?
Microsoft did an upgrade to my desktop automatically, called a service pack 3, after which my Maxtor 3200 external hard drive stopped being recognized by my Windows XP system. A code 10 error appeared every time I tried to access through my device manager, and I cannot find a driver to operate this hard drive, I will many songs and pictures if I cannot access this external hard drive. I went on the Maxtor site and they said, it is an internal driver that operates off of my system, what can I do to access the data on this external hard drive.
I have a Computer which operates on XP Service Pack 2 and has a Maxtor 1TB external Hard Drive hooked up. We do a lot of Video Editing (programs such as DV Storm, Vegas etc.) and up until yesterday the external came up as Local Disk E, but it became unplugged whilst the Editing programs were running.It now it comes up as Local Disk (I) but the problem is the Edit programs doesn't recognise any of the files (avi., mpg etc.) that are on the drive (comes up as 'invalid path'), and nor does it show them in their previous format.
I need to do an XP repair install on my Dell Dimension 8400 to fix several programs that no longer work (Update being the biggest problem). I had used this Forum a couple of months ago and doing the repair install was the recommended solution. I have a copy of the michaelstevenstech.com directions so I know what to do. Unfortunately, when I try to launch the "to setup Windows XP, press enter" step, the program comes back with an error message saying the hard drive is not found.
I am having an issue with a Maxtor Model Number 92739U6 hard drive. I have just finished formatting and installing windows xp home edition. Everything was going ok until I restarted the computer. First right after I restarted the computer I got an error message A Disk Read Error Occurred. Press CTRL+ALT+Del. I was unsure what caused this error message so I started to research this issue on Maxtor?s website and they advised me to use fdisk /mbr to repair the error. I did that and restarted the computer. Same Error?. The thing I can?t figure out is why I am able to boot right to windows using a boot disk.
I just installed a new hard drive then I installed windows XP SP2 on the disk and the computer keeps rebooting and I'm getting a blue screen c000221 unknown hard error. Then I re-install windows 2000 it works Ok. Then I installed windows XP SP1 it work OK, then I installed the SP2 and the computer started to reboot again. I used drive jujitsu and it was OK. So what is the issue with SP2 and the Maxtor drive anyone knows or has seeing this issue?
I have a maxtor hard drive SATA 200GB as my main drive and a second drive D. Very recently when I have noticed that my computer took longer to boot into windows. Applications seem to take a bit longer than usual to load. I have XP SP2 installed. I defragment my drive every few weeks so its not a defragment problem however when I try to defrag it now, it takes many times longer to do so. Also for a scan disk of C: (chkdsk on boot) it took 6 hours to get to about 25%. So there must be a problem. I can hear the hard drive loading sound for a few seconds and then there is a very long pause maybe about 10-20 minutes. It should only take a few hours the last time i did it maybe about 5 hours. Something is wrong.
When I transfer a large file like 1gb into my drive D it takes 15 minutes. Which is a bit long for a SATA enabled hard drive. I have had this drive for about 2 years now and it has never gone this slow before. I have downloaded the seatools from the maxtor website which diagnoses the drive. The tool ran slow but my hard drive passed the tests. Also when I ran that scan disk, it did say there was a mirror copy of something and also some other things. I think it had the word security in it so it deleted somethings. It mentioned indexes and some files. I forgot most of it.
I have checked my D drive and it is running fine and unaffected. Also I noticed during bootup that on the windows logo screen, the one with the bar moving from left to right that it freezes for about 5 seconds somewhere near the end of its loading. Then my keyboard lights come on (recognises keyboard). Later after the logo disappears, the screen is black for about 1-2 minutes and the hard drive periodically stops loading then starts loading something. This also happens when the welcome blue background screen comes on which is making boot times slow. Also happens when I shut down. There are some periods of hard disk inactivity.
I got a black screen, and the hard drive wouldn't boot. I took 3 old hard drives that I thought were still good, but after I formatted each one, I got a message that the hard drive was damaged . . . something else was wrong, like an improper connection . . . finally, I hooked up a new Hitachi Hard Drive, and formatted it . . . and lo and behold I'm getting the same message.
It's possible the 3 older hard drives could have become damaged, but when the brand new Hitachi gives me the same message
I found myself facing a black screen with this text:"We appologize for the inconvenience, but Windows did not start successfully. A recent hardware or software change might have caused this.It your computer stopped responding, restarted unexpectedly, or was automaticlly shutdown to protect your files and folder, choose last known good configuration to revet to the most recent settings that worked.If a previous start up attempt was interrupted due to a power failure or because the powe or reset button was pressed, or if you aren't sure what caused the problem choose start windows normally
I tried to reformat my hard drive. When it got to a certain point where it was checking the disk it got to 20% then hung or stopped. Did this three times. I have tried to run CHKDSK and have been unsuccessful. I get messages during the operation that say "file record segment is unreadable.
Once phase 1 is finished, I get messages that "correcting error in index" and replacing orphan files (or sometthing to tthat effect). Not long after that a message appears that says "an error has occured" and the computer continues to boot. Please note that my computer tries to run through CHKDSK everytime I boot. I want to reformat but it seems impossible.
I just recently installed a new hard drive and uploaded windows xp professional. To my surprise I continue to get this box that pops up and says" Critical error message! Registry damaged and corrupted. To fix this problem: open IE and type www.registryxp.com Once you load the web page, close this message window. After you install the cleaner program you will not recieve any more reminders or pop ups like this one". I went to that page and it wants to charge me to sign up for a registry cleaner. This box pops up every 2 minutes or so . I've tried other registry cleaners and pop up blockers, spyware removal, deleting cookies, add/ remove programs, everything I can think of but to no avail. I know that it's hiding somewhere but I'm not too computer literate to go to far into my system without the proper help.
My prob is a bit of a saga I defragged my Win XP Media PC a few days ago and then I noticed a clicking noise coming from the hard drive, I called PC servicecall managed to find a freephone number and the chap suggested I do a scandisk, he said to call back with the diagnosis later.
After the PC did two scandisks I managed to stop it when it was about to do a 3rd, I rebooted the PC and it loaded with no 'start' button or clock on the taskbar, so I rebooted. Then I got a message saying 'it can't load as a file was missing or corrupt windows/system32/configuration/system' it said to put in the original CD and type 'r' to repair.
Well the PC didn't come with any CD's and I only have one that I made after I'd had the PC for a month - a recovery disk.
So I called PC Servicecall back and told the guy what happened and I've got another harddrive arriving tomorrow - trouble is I need to get the info from my hard drive before I send it back to them.
I've looked at MS support site and there's options to do a manual repair (I'll copy and paste info here) Method 1: Replace the SYSTEM Hive Method 2: Restore the SYSTEM File from the SYSTEM.ALT Backup File Method 3: Reduce the Size of the SYSTEM File Method 4: Restore the SYSTEM Hive from Backup
Which all sound hunky dorey but I don't have any original bootable CD (the PC doesn't have a floppy drive), so I can't type 'r' to repair!!!!
In my possesion I do have an XP Pro CD, a Win2000 CD and a Win98 CD - my question is can I use these other CD's to try a 'repair' and get into the 'manual' area to try the methods above (the OS is Win Media Edition on the PC)?
After working for sometime with Maxtor One Touch II external drive, I have experienced the following problem: If the computer is left for some period of inactivity, for 1-2 or more hours (the light on the drive is on and not blinking) I cannot access the drive and the OS message is "One touch is not responding". The only remedy is to restart the computer. My System consists of: WindowsXP SP2 and 512 MB Ram The Maxtor OneTouch II drive is connected via a firewire inlet of the computer, the file system being NTFS. The drive is partitioned unto 2 logical drives (~150 GB each)
I have two computers (a PC and a Mac) and a Maxtor One Touch External Hard disk 250 GB. I would like to back up these two machines using a single external hard disk. So I have partitioned the hard disk into two and have NTFS and FAT32 as the file systems. The NTFS partition is around 163 GB and the FAT32 is around 75GB. I could successfully back up the PC into the NTFS part but have problems with the Mac.
When the hard disk is mounted on to the Mac, both the partitions appear on the desktop. The Mac OS is 10.3 and it identifies both partition correctly. It recognises the NTFS part as readonly and FAT32 part as "readable and writable". But when I tried to backup for the first time there was an error saying "insert a new disk". I tried to overwrite the contents of the FAT32 part as I didn’t need them any longer hence asked to proceed with the backup. The Mac started erasing. I thought it was erasing the files previously present in the FAT32 part but it continued erasing for some time and finally erased the FAT32 file system itself. So the icon representing the FAT32 part of the partition of the external hard disk disappeared from the Mac’s desktop......
I have a Maxtor internal 300gb drive that I've mounted in an external casing. The other day I knocked it over and ever since then when I turn it on it makes some kind of warning sound three times. The computer doesn't detect it anymore and I can't access any of the information on it
I copied/cloned my failing C: to a drive on USB. C: drive has now failed and I need the copy to become bootable. Why can't this question be a simple answer. What happened to fdisk utilities?
I installed the patch last night on my windows xp service pack one machine. Plugging in the drive causes the icon to appear in the system tray, but there is no drive letter assigned to the drive and going in to explorer shows the drive "locked".
I have video saved on a Maxtor 80GB external drive that is formated in fat32, from a Windows ME system. I need to move the video info to a newer PC w XP. I have read the forum comments on how to convert from fat 32 to NTFS. However when I connect the Maxtor firewire the PC will NOT RECOGNIZE the drive. Until recongized I can't convert. I have other larger external drives that are in NTFS and are recongized immediately.
I attached my xp drive as a slave to my 2000 pro drive and booted. It checked my xp drive and then started to truncate everything. I now cannot reboot my xp drive. I tried using xp cd to repair but it says I can't due to error on partition, drive full etc. I have tried my friends partition software but it finds no errors. When I use his xp drive to see my xp drive, it says it is unreadable. Is there something out there to repair my truncated files? Is this fixable or is formating my only option. I am desperate to retain my xp drive data. Using parition magic 8, it shows my xp drive as a type 07 and my 2000 as a FAT drive.
I have a damaged Windows XP CD and do not think its fair I pay just to request the info in getting it replaced. I saw this option and wanted to see if I could get something done about it.
I have a damaged OEM CD and the expired CDKEY that came with it from maximum activations as I was having BSOD problems which then was discovered to be bad RAM. The company I bought it from is now bankrupt and non-existant. Now I am left with a CD that makes a great coaster and a CDKEY that has expired from activation. When I first installed it 1 support request was already used? I had made one request and registered it with Microsoft so it has to be on archive even if it hasn't been used.Since I can't copy and paste.
I have a Dell computer where one of the loading .dll files came up 'missing' one day, so it won't boot. I want to get all the photos and other docs off the hard drive. I had downloaded one version of linux and was able to see the files on the internal hard drive, but was unable to copy them to a memory stick or external hard drive. Now I've downloaded ubuntu and booted off a memory stick... this time, it's telling me that the internal hard drive has all kinds of bad sectors and won't let me access any of the files on there.
My laptop died and I removed the hard drive.i hooked the hard drive up to my new laptop via a SATA/IDE cable.
I can see the old hard drive in the E drive and it appears that all the contents are there by the size of the hard drive (same as when I had it in the old laptop) but I can only see, actually view, a very small percentage of the drive.
My goal: I want to transfer all old music, word documents and photos from old laptop into new laptop.
current HD going bad, have second HD installed and using as back but now i need to make the second HD my primary, can i do this without having to reformat in order to add booting files.
