i have a hp windows 8 machine and it came with a recovery partition and i have since made a recovery usb drive. my big question is if i use say a windows 7 disc to wipe my entire hdd and install windows 7 could i at some point reinstall windows 8 from the usb drive or have i lost it for good?
View 9 RepliesI have a server with Windows 8 on a 360gb sata drive with 4 1.5TB drives as storage, which i had joined under Windows 8 to be seen as one drive. The system had been sluggish lately so was going to replace the 360gb with a ssd which i had used b4 on my laptop, so when i had it connected and started to install.
I seen 5.8 drive and ssd 12ogb drive and a few small partitions i deleted main partition on ssd and few other small partition which i thought was on the SSD but one was related to the storage drives and they are all screwed up now and when i connect the original Windows 8 os hard drive it doesn't boot anymore.
My question is whats the best way to proceed to save all the data on the hard drives nothing was formatted on theses drives.
Recently i purchased HP Pavilion 14-b030tu Sleekbook off eBay where the guy told me that the computer was always stuck in automatic repair.
So i ran HP diagnostics on the drive and it came back with the "Short DST failed", i know that when the short dst failed tests means that the hdd is about to die. Currently i have removed the hdd and have connected it to my computer where it still gets recognized as a hard drive.
Because i dont want to spend money buying a USB with the HP recovery image on it:
1) Any way to recover data off a GPT hard drive? Ive tried Active@ File Recovery but it doesn't allow me to do anything except super scan the drive.
2) Where the recovery image is stored in harddrives from HP ultrabooks that run Windows 8?
After 5 years of use, my college laptop (Windows Vista) finally gave up on me a couple of months ago. Each time at start up, it would automatically go to the blue screen of death and never get past that point. I wound up getting a new laptop (ASUS S500CA) operating on windows 8, and now I'm attempting to recover some of my files from the old hard drive. After a little reading, I discovered that you can pull the old drive, connect it to another computer via a USB cable, and attempt to recover the data on the drive. So I ran down to the local best buy and picked up an Apricorn SATA Wire. Here's the problem. Every time I hook the hard drive up to the computer via the USB wire, my computer instantly goes to a blue screen and goes into a cycle of restarting itself over and over. Does this mean that my old hard drive is just too far gone to recover, or is there another method that I can try?
View 2 Replies View RelatedWoke up this morning to a frozen Windows 8 screen. Only way out was to power off. On reboot, my nightmare began.
No boot device. Long story short, I went through many attempts at a reset, repair, reinstalls, off the Windows 8 DVD, all to no avail. Indeed, when I booted into Dell diagnostics, it confirmed a failed hard drive.
(Sidebar : was there an automated patch pushed last night.....like there was for Win 7?).
Keeping calm, I know I have all my data backed, up, but I am trying to avoid having to rebuild everything from scratch. I have been vigilant in doing image and file backups for years..... But I always manage to hit a brick wall somewhere along the way.
I have summarized what I have and do not have available to me here : Recovering from disk failure
I have a dell laptop with winows 8 preinstalled on it. Soon after the purchase of my laptop I created recovery disk. It had only a single partion that time (Only C drive). Later I created a new partition 'D' from the existing space in C drive. Now my question is , can I still use the windows recovery disc that I created at the time when I had just one partition (just C drive)??
View 3 Replies View RelatedAfter 5 years of use, my college laptop (Windows Vista) finally gave up on me a couple of months ago. Each time at start up, it would automatically go to the blue screen of death and never get past that point. I wound up getting a new laptop operating on windows 8, and now I'm attempting to recover some of my files from the old hard drive. After a little reading, I discovered that you can pull the old drive, connect it to another computer via a USB cable, and attempt to recover the data on the drive. So I ran down to the local best buy and picked up an Apricorn SATA Wire. Here's the problem. Every time I hook the hard drive up to the computer via the USB wire, my computer instantly goes to a blue screen and goes into a cycle of restarting itself over and over. Does this mean that my old hard drive is just too far gone to recover, or is there another method that I can try?
View 4 Replies View RelatedI'm booting off my SSD which is drive C: and I have games and programs on an extra hard drive which was origanally drive H: but after a restart it switched to I: and when I go into Disk Management to change it Drive H: isn't there.
View 3 Replies View RelatedI have a 2TB Western Digital My Book Essentials, it's filled with tons of old photos, movies, docs, games, and I'm scared to think of what else. The SATA to USB connector broke on it, so I took the drive apart and put it inside my computer. I opened up device manager because it wasn't showing up automatically and the 2TB is showing up as unallocated, I'm freaking out now because I'm scared the data was somehow deleted.What do I do?
edit: I realize also this isn't directly related to Windows 8 (besides the fact it's the OS I'm on), but I don't know where else to post it. I'd also like to say that I had a really deep feeling the drive was going to break continually for about two weeks before it happened, so if you have a similar feeling about something, don't ignore it!
When I go to Computer Management my main (OS) drive shows as "Disk 1" and my 2nd internal data drive shows as "Disk 0". Should I switch the SATA cables so that the main drive will show as "Disk 0 and the 2nd internal drive as "Disk 1"?
View 5 Replies View RelatedI have just bought an AIO Asus desktop with 1 Tb of storage. The c: (Windows)drive is allocated 100gb and the d: drive 931gb. I just want to transfer all the data from my old computer. This was pretty much all in the folder c:>Users>Myname, but when I try to transfer it all into the same folder on the new computer, obviously with 100gb there is not enough space.
View 2 Replies View RelatedCan you save to hard drive and One Drive at Same Time?
View 2 Replies View RelatedI have a laptop that has an SSD with Win 8.1 + programs, and an HDD for projects. They are both formatted GPT. When I launch Macrium, for some reason my SSD is now GPT 1 and the second drive is now GPT 2. This is confusing because I'm used to imaging the top line of partitions which is usually my OS. Now that the GPT numbers are reversed, I have to be careful when doing my backups. How to change this assignment so that the SSD will be GPT1 again?
View 9 Replies View RelatedI'm in the process of moving to an SSD and need to create a backup drive in order to repair the BIOS after transferring everything. However, when I try to create one - the create a recovery drive program won't recognize the flash drive I have connected as a flash drive.
I first tried with a SanDisk Cruzer which apparently had a quirk in that it shows up as a hard drive instead of removable flash drive. That seems to be well documented on forums all over the place and there is no fix.
So, I purchased a cheap 8 GB stick (no brand) and Windows (I'm running 8.1 x64) recognizes it as a removable disk. However, the create a backup utility still won't recognize it. I've found some random fixes that have worked for some (such as plugging it into a different USB port) but nothing has worked for me so far. I've tried doing it with the "copy the recovery partition" option both checked and unchecked.
If there's no solution to this wonderful "quirk" of Windows, then is there something else I can do to repair BIOS? Seems like there's not a fix to my problem out there...
EDIT So as of right now, I tried using HPs recovery software which seems to do the same thing as copying over your entire recovery partition. That didn't work either. However..when I had both USB sticks plugged in the Windows supplied utility recognized the SanDisk Cruzer when I checked the "copy the partition" thing
Windows 8.1
pc bought in 2013 with windows 8 bundled (so no installation DVDs, no activation key communicated).
upgraded to windows 8.1 in 2013.
I made a recovery USB (system image) on 1st April 2014.
If I need to boot on this USB, my PC will be again exactly as it was on 1st April 2014?
I know there is good software out there to clone/image my hard drive and restore it to a new SSD drive. I'm just wondering though, since my laptop is brand new, I made a full recovery to a USB drive and included the OEM recovery partition.
Couldn't I just swap out the old HDD with the new SSD and boot with the recovery stick and do a full recovery back to the new SSD?
Also, however I do this, recover or image backup/restore, do I need to do some type of SSD alignment? I can't find a clear answer on that.
I just purchased an Asus R510CC notebook with windows 8 and I bought a SSD drive to replace the current one.
I used Recovery Drive in Windows to create an USB boot drive with the recovery partition on it. I then installed the SSD and booted from the USB. When I get to the option to reset my computer I encounter an error with the following message: "Unable to reset PC. A required drive partition is missing". I already did a bit of research and BIOS tweaking but I can't install Windows onto my SSD.
I just upgraded to 8.1 update 1 officially via Technet. As expected, SkyDrive has been renamed to OneDrive. However, if I look at my OneDrive folders via Properties | Location it still points to a SkyDrive folder. Even software that I use to store backups on my OneDrive folder still point to SkyDrive even though there is no folder with that name. If I try to change it to OneDrive I get folder not found.
View 9 Replies View RelatedI am wanting to install my W8 O/S onto a 64GB SSD drive. I just want to use this for boot purposes and to fit some programs on as well. Everything else I am wanting to have stored on a 1TB WD Black drive. I want to point my libraries (Docs, Music, pictures) towards the 1TB drive. How do I do this?
View 2 Replies View RelatedMy flash drive shows some virus so i am scared that when i open it then the virus will be transmitted to the c drive and make my pc slow. so is there any method that i can open the drive virtually in my pc and remove and delete those affected files?
View 6 Replies View RelatedI have three hard drives. One is a Kingston Hyperx SSD 120GB. The other two are for internal storage and are WD 500GB Blacks. I recently upgraded my computer. My new mother board is the ASUS M5A99X. I installed Windows 8 just fine back in Dec 2012 and it worked up until April-Mayish. My USB Hub was causing my computer to halt before POST. After exchanging it with a new hub, I was able to boot just fine.
Later that same day, I cleaned out the dust in my computer and added another harddrive. I wasn't able to boot Windows 8. It would just stop with a blinking cursor right before it should show the four blue panes. I went into BIOS and it didn't have my SSD listed. I accidentally unplugged the SATA cable for my SSD and forgot to plug it back in. After I plugged it back in I set the boot priority back to my SSD first.
I still couldn't boot so inserted my Windows CD to reformat. After it says "Press any key to boot from CD...." I didn't press anything and it loaded into Windows just fine. I loaded Windows this way for a while until I was able to troubleshoot it. After reformatting, I get "Please select proper boot device.." message. If I put the CD in, that goes away and it loads into windows after saying "Press any key to boot from the CD..." Here's what I've done to troubleshoot so far:
1. Set SSD to first in boot priority order in BIOS. Forced boot to my SSD in BIOS. Changed SATA from AHCI to RAID (lol) to IDE.
I've used bootrec.exe and tried
bootrec /RebuildBcdbootrec /fixMbrbootrec /fixboot
This still didn't resolve my issue.
2. I flashed my BIOS to 1708 because it was going to fix an issue I had with a USB device.
3. I reformatted Windows 8 with all drives unplugged except my SSD.
4. I've unplugged all SATA devices except my harddrive and tried to boot.
5. I've set the 2nd partition (90+GB) to active partition on my SSD.
My next step is to RMA the motherboard.
Why cd drive not working on windows 8 pro?
View 5 Replies View RelatedMy C Drive Keeps getting full even though i hardly have anything installed there. most of my games and programs are on drive D and i also moved my "My Documents" Folder to D. Even so, C drive keeps getting full..
View 5 Replies View RelatedI have installed windows 8 64 bit on (C) and I would like to install the program files, printers, etc on another drive. I have 3 drives 1- ssd, 2- 1TB drives, 1- blu-ray player. This is the first computer that I built. Now how to finish my project.
View 1 Replies View RelatedI need a recovery drive for windows 8 so that I can boot into advance settings via USB. I can't get my computer to start up anymore past the desktop screen, unfortunately that's where it just freezes on me.
View 3 Replies View RelatedYesterday I was working on some stuff on my computer and left it when my door rang. When I came back the computer was on but no matter how many times I tried to move the mouse or press keyboard shortcuts Windows wouldn't come back on. So I manually powered down, and then it got worse. It wouldn't repair manually or from the Windows disk. I tried all kinds of stuff. I tried a refresh install but I got this
"The drive where Windows is installed is locked" Then this morning when I went back to back to turn it on and trouble shot. All I got was a black screen. No NVIDIA window or anything.
After installing the first set of Win8 updates through Win Update, my PC no longer registers its DVD/CD drive. I've found this is a relatively common problem having looked online but can find no working solution for it.
I've done the reg edit tweak which is widely published but that does not correct it, nor does d/loading the free version of Win Media Centre.
My first look at Windows 8. I got a new notebook with Windows 8, no optical drive and no recovery partition. I created the recovery file on the hard drive.The file is around 13 GB. Windows wants a USB flash drive of 16 GB capacity to make a recovery drive.
I give it a 16 GB flash drive and Windows insists on formatting it to FAT32. A 13+ GB file won't write to a FAT32 drive so the operation fails in the end leaving 228 MB of data on the flash drive. What's up with this?
I am new to Windows 8, and first time with a laptop. I have 1tb hard drive (minus a few gb) in c drive. d drive is being used as recovery
This is how it was setup. What I would like to do is to partition the amount of space i have from c drive into another drive.
Can manage to partition some hard drive space over to another driver letter, if i do a fresh install of windows, will this new drive be formatted too?
(Just asking this because when I owned a desktop computer, I had two drives. A c-drive and a d-drive. When I re-installed windows 7 on the desktop, all my files were still available on the d-drive, hence asking the above last question).
I got this new Asus Transformer which is a Windows 8.1 system.
I made a few images with Macrium Reflect and created an UEFI recovery Flash Drive (with Macrium) for the Macrium recovery program. I can set the BIOS to boot from the stick (in the temporary or permanent BIOS settings). Problem is, when I hit Enter, it ignores the stick and boots directly into 8.1.
Is there another setting in the BIOS that I have to make in order to have it boot from the stick.
I have a hp 475 homeserver with new upgrades. i'm trying to install windows home server 2011 on it. I want to put the whole sys on a bootable flash drive and install that way. I have ms dvd tool and software for iso files, now I think I need to combine all in a bootable flash drive for win 8.1
View 1 Replies View Related