Setup Installation :: Want To Add Second Sata As Data Drive?
Sep 27, 2013
I had one sata drive wanted to add second sata as data drive.i disconnected older hard drive connected new one,installed windows 8 on it,everything went fine.I did not format older drive yet,reconnected it afterwards,changed boot order in BIOS but the second sata drive reads bus number 0,one with operating system reads bus number 1.Is this O.K.?Usually bus number 0 should be the operating system is on.How can I change this?
When I go to Computer Management my main (OS) drive shows as "Disk 1" and my 2nd internal data drive shows as "Disk 0". Should I switch the SATA cables so that the main drive will show as "Disk 0 and the 2nd internal drive as "Disk 1"?
I am planning on building a new computer, and I want to put a 250GB SSD (Samsung 840 EVO) in it to use with 8.1 Pro. However, most of the programs and data I need are still on the old computer's boot drive, specifically all of my STEAM games (none of which I have the DVDs for.)
My question is if I can create symlinks to the old boot drive without losing data on it. This will most likely be a temporary measure, as the drive's a fairly slow 5900RPM Barracuda, and I want something faster, but I can't afford a better one just yet...
After 5 years of use, my college laptop (Windows Vista) finally gave up on me a couple of months ago. Each time at start up, it would automatically go to the blue screen of death and never get past that point. I wound up getting a new laptop (ASUS S500CA) operating on windows 8, and now I'm attempting to recover some of my files from the old hard drive. After a little reading, I discovered that you can pull the old drive, connect it to another computer via a USB cable, and attempt to recover the data on the drive. So I ran down to the local best buy and picked up an Apricorn SATA Wire. Here's the problem. Every time I hook the hard drive up to the computer via the USB wire, my computer instantly goes to a blue screen and goes into a cycle of restarting itself over and over. Does this mean that my old hard drive is just too far gone to recover, or is there another method that I can try?
After 5 years of use, my college laptop (Windows Vista) finally gave up on me a couple of months ago. Each time at start up, it would automatically go to the blue screen of death and never get past that point. I wound up getting a new laptop operating on windows 8, and now I'm attempting to recover some of my files from the old hard drive. After a little reading, I discovered that you can pull the old drive, connect it to another computer via a USB cable, and attempt to recover the data on the drive. So I ran down to the local best buy and picked up an Apricorn SATA Wire. Here's the problem. Every time I hook the hard drive up to the computer via the USB wire, my computer instantly goes to a blue screen and goes into a cycle of restarting itself over and over. Does this mean that my old hard drive is just too far gone to recover, or is there another method that I can try?
I was wondering is there any way to increase the data transfer rate on SATA drives. My MB has SATA 3 and I have a Samsung HD 154UI drive on SATA /300 where I have Windows 8 x64 installed. The performance under Windows is 5.9. This is the lowest on the list. CPU 7.4, Memory 7.4, Graphics 7.9, Gaming graphics 7.9, Hard disk 5.9...Is there a way to get it higher without replacing the drive. The drive is new (only 3 months old) I have two of these drives and two Seagate drives that are 2 tera which are 1 year old.
I am trying to get my external hard drives setup from a freshly rebooted installed computer. I recently placed an external hard drive with all my back up files on my computer, but this drive is not going to be my main drive. I have two others I will be using as a main hdd and a backup drive that are brand new.
So, the question is, if I were to use a utility like the Windows 8.1 disk management feature to either delete the drive letter or even change it to another one, will that mess up the external hard drive or even lose data? Because until I transfer my files to my backup disk I am afraid of losing my only copy of my files.
I have brought a Dell Inspiron 17R SE. It came with a 1.5TB HDD With a rotating speed of 5400 RPM. As the day is passing the Laptop is becoming slow and slower. So I have thought to buy a Samsung 840 Pro 128GB SSD and install it along with my HDD. So my question is that is there any way to move all the files from my C: drive to that SSD and make that SSD as boot drive without losing all my files. Then my 1.5 TB HDD would be my data storing drive.
Samsung 840 Pro 128GB Specs - Solid State Drives MZ-7PD128 | Samsung Memory & Storage
I want to move all my data from my MacBook to a laptop with Windows 8. I have everything backed up on an external HD; when I plug the HD into the laptop, it's not recognized. I've tried transferring via WiFi, but the MacBook is not allowing that to happen. Is there anything I can do with my backup HD so that it is recognized by my new Windows 8 laptop?
I have 3 disks in my computer, of which 2 are SSDs.
I swapped the SATA ports between one SSD and the HDD so as to give the SSD a SATA port with maximum 6gb/s transfer speed, and now the access to the HDD is denied. The drive letters are correct, as they should be.
The user (myself, admin) did not change.
What can be done about it? I already tried to check the ownership of the drive and says STEVECOMPUTER/Administrators, which looks good, as my user account is an admin. Still, I have no access.
How do I slave a hard drive on my Windows 8 Computer?
I had the hard drive slaved to my xp and it was fine, I plug it in to Windows 8 and it doesn't recognize it. Plug it back into the XP and it shows up fine. I'm not really experienced with this, I'm used to just hooking the hard drive up and booting up with XPs and it knows there's another HD available for storage, is the process different with windows 8? is there something specific I need to do to get it to recognize the HD?
The computer is an ACER Aspire 3. 4Gb RAM. 500Gb memory.
I've been using the computer for a month and a half more or less and everything went OK only few small problems but 2 days ago. It did not Boot.When starting the PC the following appeared:
Recovery Your PC needs to be repaired
The boot configuration data file is missing some required information. File:BCD Error code: 0x000000d You'll need to use the recovery tools on your.....
The first thing I did was creating a bootable USB with Windows 8 software, it did not work. SO i used Rufus, it worked and launched the Windows 8 installation and recovery but when I tried to recover, refresh, anything it told me the disk was locked... or anything the only thing I'm able to access is Command Prompt.
I've been trying some commands that I've seen online but no luck so far. Some commands tell me "OK, successfully something" But when reboot and I change to default the boot order and UEFI then the same error appears.
My computer has the BSOD that says inaccessible boot drive and i think its because of the sata mode selection. But there is only one selection AHCI when I think I need ata. I don't know if I do need it be there hard drives serial ports say ata.
Thought this was problem - Microsoft writes "When you resume a computer from sleep or from hibernation, the SATA hard disk drivers require the SATA hard disks to be ready within 10 seconds. However, a large SATA hard disk may take longer than 10 seconds to be ready. In this situation, the resume operation times out." in their fix for W7 - You receive various Stop error messages in Windows 7 or in Windows Server 2008 R2 when you try to resume a computer that has a large SATA hard disk
Have tried a variety of things like checking all current drivers, turning off hybrid sleep, power troubleshooter, windows update and the like on instruction but my ASUS p7p55d-e doesn't seem to have any Windows 8 specific drivers.
boot drive C: (partitioned into two logical drives)
So I had this recovery error that said my winload.efi was missing so I ran the recovery from boot up and decided to recover. I read that this will delete the files from C: so I turned on the "Maintain User Data" option and selected all including the local disk c from advanced selection. But when the process was finished, my laptop was empty and no data was restored. What happened ? did I just misunderstand how it works and now it's gone ? or is it just somewhere I can't find ?
I'm not sure what I did, miss be when I was installing activclient but now I have a boot error asking for the windows installation disk. Also says
File: BootBCD Status: 0xc000000f Info: The Boot Configuration Data for your PC is missing or contains errors
I booted in recovery mode but I can't make a system recovery drive on a USB because it says the boot files are missing. And I don't have a recovery disk because SAMSUNG ATIV 6 doesn't have a disc drive. I've been searching the web for a recovery disc download to no avail.
I am trying to install a graphics card in my desktop pc. The heat sink on the card blocks the SATA port that the DVD drive is plugged into (SATA1) so I've switched the DVD drive to SATA2. The drive is now showing as connected to port2 in the BIOS, but in windows (Windows 8 64-bit) it isn't detecting the DVD drive at all? I've seen other posts about this on the internet suggesting to add a line to the registry, but I've done that and it doesn't solve the problem.
I got this msg tryng to refresh my pc . because my vaio gate app wasnt working right . so after the restar i just got the blue screen with this error the boot configutating data file dosent have valid infomation of an operating system.
I have just bought an AIO Asus desktop with 1 Tb of storage. The c: (Windows)drive is allocated 100gb and the d: drive 931gb. I just want to transfer all the data from my old computer. This was pretty much all in the folder c:>Users>Myname, but when I try to transfer it all into the same folder on the new computer, obviously with 100gb there is not enough space.
I just purchased an Asus R510CC notebook with windows 8 and I bought a SSD drive to replace the current one.
I used Recovery Drive in Windows to create an USB boot drive with the recovery partition on it. I then installed the SSD and booted from the USB. When I get to the option to reset my computer I encounter an error with the following message: "Unable to reset PC. A required drive partition is missing". I already did a bit of research and BIOS tweaking but I can't install Windows onto my SSD.
I have a HP Envy 4 Ultrabook and I want to install Windows 8 from scratch, I put the installation files on a flash drive from a DVD of Win 8 I had, but when I go to install it, it says the "We couldn't find any drives". I have tried using DiskPart within the CMD as well, but it only finds my flash drive when I run list disk. Also, my drives are completely formatted, and I accidentally wiped the recovery partition. I tried with a USB of Win 8 Pro, and it was fine, showing all of my drives correctly, but that version is linked to another PC, so I can't install it. Also, I booted into a Linux Mint live CD and tried to install it, it sees my hard drive correctly, but the Windows install does not, I can't figure this out, never encountered it before. Is Linux my only option at this point?
I am trying to upgrade from windows 8 pro to windows 8.1 on a samsung laptop. The download completes and installation starts.
After a while the following message appears "you cant install windows on a usb flash drive with setup"
I am not actually trying to install to a flash drive. I contacted Microsoft and after 5 hours they said that I should connect to the internet with a cable and not by wireless in order to solve the problem (this didn't work of course and I had told them that it was an install problem and not a download problem).
I have a windows 8 laptop and wanted to re install a whole new windows 8 on it. I'm going to use the generic product key than once installed use the one that i found with magic belly bean key finder. I am just worried that it might say something went wrong than have to buy windows 8 so could i partition the hard drive and than once i know the new windows 8 is good than delete the other?
Just purchased a new win 8.1 computer. As you know it only has the system, recovery partitions and a very large C drive containing the OS and whatever programs that came with the computer.
After cleaning up any unneeded programs, I would like to create 2 more partitions besides drive C:
Total HDD Capacity is 1TB
Is the free space on drive C: indicted in disk management an accurate reading?
Is 80G enough for OS and programs plus some spare space ?
I base the 80G on my older win7 computer where I allocated 78G and only used 44G after 4 years . I am sure I can get away with only 60G but I prefer some wiggle room .
Alright, I just installed my Windows 8 Pro from a USB drive as I was installing it I was installing Windows 8 on the W:/ drive but once it was installed I came to found out that that My C:/ drive which was originally Windows 7's drive letter now belongs to Windows 8, and now the drive that is now Windows 7's is D:/ is is possible to change it back a W: drive or something? and yes, Windows 7 is the main partition on the system, I'm not sure why it changed but it's actually the first time this has happened.
