I am having problems installing UEFI & a Error 0x80004005 with Windows 8.1 OEM saying it can't create partitions for UEFI then creating 2 partitions for MBR installation instead. This using a 400 TB, hard drive, setup with a GPT system & nothing else & ready for Windows 8.1 to create the partitions.
The first time it happened I used MiniTool Partition Wizard Professional, to delete the partitions created by Windows 8.1 & convert the MBR to GPT, then used Wipe Disk function to erase all data and set all the bits to a 1.
The only thing that I can think is upsetting the installation is that I have left the other drives in the system including 1x3 TB drive, 1x2 TB drive and a second 4 TB drive.
The 2 TB drive has "Win 7 Ultimate" installed using MBR, the 3 TB drive is empty but ready to install Windows 8.1 setup with GPT, and the other 4 TB drive has a UEFI Windows 8.1 installed but broken.
I have also tried to install UEFI Win 8.1 on the 3 TB drive but it failed with the same error code as above.
This UEFI takes a lot to get ones head around dose't it, and me being much older than I once was makes it even harder. I have tried this installation at least 3 to 4 times now and doing these "Wipe Disk Functions" every time has so far lost me 3 whole days just in wasted time.
I have tried installing Win 7 in UEFI on my old Asus K56JV Laptop.
I have used a tutorial by Brink to create the bootable usb. The system can see it but after it has loaded, I get the following message:
Windows failed to start. A recent hardware or software change might be the cause. To fix problem
1. Insert your Windows installation disc and restart 2. Choose your language setting and click next 3. click "repair your computer"
status 0xc0000225
What should I do from here?
I have tried to make the usb both manually and with rufus usb software. The system does not currently run on UEFI, but it supports it, and I have changed it in BIOS. Also I run Ubuntu in dual boot. I don't know if the GRUB interface does anything here, because the recovery will not start either, though I believe it did so last time I formatted the laptop
using the UEFI install instructions from this forum. I do meet all of the requirements (Windows 8 64-bit iso, ASRock Z87 Extreme4 mobo, blank SSD). When I get to Step 7 in the UEFI guide, I only get 2 partitions instead of the 4 shown(Recovery, System, MSR, Primary). I only get System and Primary. I decided to delete all partitions and just run the setup on the unallocated drive...everything worked fine. I am just wondering what the consequences are of not having those 4 partitions. I still have the UEFI interface when I boot up so it appear that is working.
Why windows 7 and windows 8 introduced a limitation when using Disk Management, and is NOT possible to create more than 3 Primary Partitions? However, using DiskPart from command line it is VERY possible, no warnings or notices.
Code: C:Windowssystem32>diskpartMicrosoft DiskPart version 6.3.9600Copyright (C) 1999-2013 Microsoft Corporation.On computer: PAINKILLERDISKPART> listMicrosoft DiskPart version 6.3.9600DISK [code]....
As far as I know, there is a maximum of 4 Primary partitions on a hardisk, or 3 primary and one extended, and IN the extended partitions more that 4 logical drivers.However, from any disk utility like the old, deprecated, and buggy Partition Magic, acronis disk partition utility, gparted Linux, parted, cfdisk, fdisk, or even on the older Windows like Xp, nt, 2000, 98, me, ms-dos, freedos, I WAS ALWAYS BEEN ABLE TO CREATE 4 PRIMARY PARTITIONS, but with the new WINDOWS 7 and the new WINDOWS 8, it appears this limitation of only 3 PRIMARY PARTITIONS instead of 4. Don't know about Vista as I have skipped that version of windows on every PC that I have build or worked.
Or is working like this because of some hidden reason which I can't figure out by myself what could It be, and the only thing that I can observe is that while technology is evolving (hardware and software), we have limitations like this, to create only 3 primary instead of 4 primary while using Disk Management from administrative tools or right clicking on the computer and "manage" console.
Personally I am a little irritated/annoyed that now the disk management is having "handicap" and I can NOT find a serious reason for this idiocratic limitation. As we are "evolving" the normal path It would be more normal to be able to use more that 4 primary on a hardisk, from my point of view, not limiting to ONLY 3 Primary.
have Acronis 2013 Plus. What I am trying to do is image the disk of a Windows 7 machine (source) to a machine that had Windows 8 pre-installed (target - Gateway SX2110G).
I connected the Windows 7 drive to the new machine (USB data cable), disabled Secure Boot, and enabled Legacy. Booted to True Image and started the cloning of the drive. Everything seemed to go ok, but as soon as it starts to boot Windows 7, it gives a 7D BSOD. (the same BSOD it gives when I simply plug the source hard drive into the target and try to boot from it).
The source HDD (win 7) boots fine in its original machine.
*I tried the startup repair that's included with the image.. does it matter if I use the one from a disc instead?
Anyways, my machine is running win7 HP with the drive bitlockered, can i just go install Windows 8 straightaway or do i have to decrypt and disable bitlocker first?
I bought an upgrade version of 8.1 Pro from my university, so I need to have an os installed before upgrading. However, I want to install it on my new PC, which means I have to install Win7 before upgrading. I wanted to know if I can install win7 and immediately install the upgrade, or is it better to go to windows update and install all the updates before upgrading?
I installed Windows 8/8.1 on a system with a Gigabyte GA-Z77X-UD5H MB. When I look at the SSD where Windows is installed I have one partition. I also installed Windows 8/8.1 on an ASRock Z77 OC Formula MB. When I look at the SSD where Windows is installed I have three partitions - 300MB (Recovery Partition), 100MB (EFI System Partition) and 111.27GB (Boot,....Partition). Why did the Windows 8 installer create three partitions on the ASRock system? I think I understand the EFI partition since the ASRock BIOS has a "Load UEFI Defaults" option. The Gigabyte MB does not have this option in the BIOS? Is that because the ASRock MB has truly implemented EFI and uses the EFI System Partition to store boot information?
Why was the Recovery Partition created? I built this system from scratch so there is not any third party involvement. If I reinstall Windows 8 using a new - never used SSD will I get the three partitions? If I format the SSD with one partition prior to Installing Windows 8 what will I get?
I not concerned about the loss of 300MB,why I got different partition configurations on fresh installs of Windows 8 on two different MB's/Systems?
Is it possible to install Windows 8.1 as Legacy with MBR? Or only as UEFI with GPT? I'm kind of confused with all this UEFI business, I always used MBR in my Windows installations. Also, Truecrypt does not support UEFI, so if installing Windows 8.1 I should do it as legacy.
Also, how can I control during the install process if I want to set my system installation as UEFI or Legacy?
I have an Acer Aspire 5745G-644G50MNKS notebook with preinstalled OEM win 7 home premium.
Specs as following: Core i7 640M Processor (2.87GHz, 4MB L3 Cache)4 GB DDR3 RAM500 GB HDD15.6" 16:9 HD LED DisplayDVD RW1 GB VGA (NVIDIA GEFORCE GT 420M)WIFI / Bluetooth / Card Reader / Web Cam
I'm wishing to update my system into Windows 8 Pro or Enterprises. But unfortunately my model isn't appears in Acer's Windows 8 Eligible Models list or Affected Models List.
I think my system has more than enough performance to run Windows 8. But my bios don't have UEFI support. So, i just wanna know will my computer be able to run Windows 8 without any troubles without that secure boot option.
I"ve run Windows 8 Upgrade Assistant Tool in my system and it says everything is okay except Secure Boot option. also I'v checked individual hardware vendor sites for the latest drivers for windows 8. Most products has the drivers, And the current drivers also compatible with Windows 8 according to the upgrade assistant.
What should i do so? Will the win 8 upgrade useless in my system? or it will be better than the current win 7?
Have any of you successfully installed Windows 8 with UEFI on a RevoDrive X2 (PCI-E express card)?
It starts the installation just fine for the RevoDrive X2 after loading it's drivers, but on first restart it...:
No boot drive found.Manually select to boot from the RevoDrive from the boot menu (F11), and it just restarts the installation again from scratch.
It installs and runs just fine with legacy BIOS (MBR) for the RevoDrive X2.
It also installs and runs just fine with UEFI on an internal SATA2 HDD.
Things I've done:
Bootable Windows 8 USB formatted as FAT32 w/EFI folder in itEnabled wake on PCI-E/PCM in UEFIBooting from USB from boot menu (F11) and not set to always boot from USB.
I just install windows 8 using BIOS , but now i want to change it to UEFI boot. so i followed steps below
1.create and format a new FAT32 partition K:
2.my windows8 is in I: so , i use this command bcdboot i:windows /f all /s k: and succeeded.
3.i checked with the bootice about the BCD in my K: and found it indeed point to i:windows just like the picture below [URL]
4. and i restart, choose uefi boot in BIOS configuration and it showed like this: [URL]
5. i checked my k:/windows/system32/ , there is a winload.efi file... [URL]
The most strange thing is that i've copyed my winload.efi to other computer which is already in UEFI mode , and also i've copyed it in my virtual machine, it works fine! So my winload.efi should be OK.
when i try to install a driver for the serial port PCI i get this error message : " Windows found a driver for your device but encountered an error while trying to install, installation of this device is forbidden by system policy. contact your system administrator . " knowing that i am the administrator!!
I have downloaded Windows 8 Pro 64-bit through the students/partner site and burnt it on a DVD. When I boot from it though I get many types of errors....the most common is 0xc0000098 that says that my PC needs to be repaired and that one or more files are missing or contain errors...I have also tried burning 3 different dvds with different programs to make sure it's not a program's fault but still with no results..
I recently installed Windows 8.1 entreprise x64 (French), connected it to a new Microsoft Account (verified) but every time I open the Store it shows this screen.Sans titre.png... I've tried :
My system: Brand new Asus CM6870 desktop 2 TB HD 16 GB RAM Win 8 Core (originally installed by Asus) Motherboard; Asus P8H77-M Pro (AMI BIOS 0606) Asus did not supply and will not supply original Win 8 media
I also purchased an OCZ SSD with the intention of moving Win 8 to the SSD. The exisiting HD is installed as a UEFI device and I wanted to install Win 8 on the SSD as an UEFI device too.
I installed the SSD on port 1 of the SATA III (AHCI). In every win install attempt I had the HD disconnected. When reconnected, it was on SATA III port 2 (AHCI).
After MANY, MANY attempts, I have Win 8 installed on the SSD and the original Windows 8 remains on the HD. I was unable to to a UEFI install, so I gave up and did an MBR traditional install. When I boot to the SSD, Windows works but I can't see the HD. When I boot to the HD, Windows works but I can't see the SSD.
To make a VERY long saga, less long, I attempted the following.....- created a recovery drive to use to do a clean install on the SSD - didn't work - "found" original Win 8 Core media and used it to install on the SSD. (It worked but it was a MBR install. I tried this many times using both a DVD and a UEFI formatted USB drive using instructions found on this forum) Up to this point, any time that Win 8 was installed on the SSD, I could see the HD as a secondary drive. If I booted to the HD, I could see the SSD as a secondary drive.- I then tried to clone the system using Paragaon - it couldn't see the SSD - I then tried to clone the system using Mini Tool Partition Wizard (as recommended by OCZ) - it proceeded but failed and I got the "Starting Automatic Repair" message that froze the system. After unplugging the SSD, it booted to the HD. - Based on posts here and other forums, I read that you could use the Windows 8 Pro upgrade to do a clean install. I bought it and upgraded my HD. - The upgrade would not install on the SSD. It would only upgrade so I re-installed Win 8 Core on the SSD and then upgraded to Pro. (I had to add a PID.txt file with my upgrade licence to the upgrade disk.) After I did this, I could no longer see the secondary drive regardless of whether I booted to the HD or the SSD.- Then I re-installed Win 8 Core on the SSD to see if the Pro upgrade was the issue. - no change I looked in Device Manager and I don't see any errors but I don't see the secondary drive.
I'll attach jpgs of the Device Manager from both the SSD and the HD Win installation"
The SSD appears as unallocated on the HD Disk Manager even though Win 8 is working on that drive! The HD does not appear on the SSD Disk Manager.
I've worked on so many alternatives over the past week that I feel like I'm going around in circles.
I'll settle for a Win 8 MBR installation on the SSD with access to the secondard HD.
i have one 750GB hard disk with 8 partition. i installed windows 7 in first partition and windows 8 in second partition. i want to hide windows 8 drive when i boot in windows 7 and hide windows 7 drive when i boot in windows 8. with NeoGrub tools in EasyBCD can do this,
I'm mostly a Linux user, but I recently bought a laptop with Windows 8 on it. After a few days dual booting I decided it wasn't for me, so I decided to delete the windows partitions and usa just Linux. I would like, however, to keep the recovery partition, so to be able to easily reinstall Windows again if I felt like I needed to, but I'm not sure what partitions should I keep. Here's a picture of my hard drive partitions as of now:
Do I need more than the restore partition? Can I get rid of the boot one? What about the recovery one? And the one flagged msftres?
I dual booted win 7 n 8. now i am running out of space in the drive which contains Windows 8.
Win 7 is installed on C drive and Windows 8 on D drive. How can i interchange the OS on the drive. I want to install win7 on Drive D and Windows 8 on Drive C.
At the moment I'm using Win 8 on the MBR HDD and I would like to convert to GPT without losing data stored on partition 2. I'll be reinstalling Win 8 on partition 1 so I can take advantage of UEFI.
I had a 17 GB unallocated partition. I changed it to a Primary partition. It is empty. Can I merge it with the C: partition ? Picture--- edit--- A picture---
So I'm using linux on my hp laptop where was previously windows 8. I have made backup of Windows 8 with HP recovery manager on a dvd and completely formated hdd. Now I want to install windows 8 but only on external hdd. I have tried using official windows 8 iso but it says that my key cannot be used to install retail version of Windows 8.
I already bought and installed Windows 8. I have a i7 laptop with 64bit proccessor but somewhat the company decided to pull it out with win7 32 bit OS. When I upgraded to Windows 8 I wanted to switch to 64bit but didn't find the option for that during the installation proccess. Can I do it now? switching from 32 to 64 (I understand that I will need to reinstall the windows again, I just don't wanna pay again for that).
