Setup Installation :: Windows 8 Installer Create Three Partitions On ASRock System?
Jan 8, 2014
I installed Windows 8/8.1 on a system with a Gigabyte GA-Z77X-UD5H MB. When I look at the SSD where Windows is installed I have one partition. I also installed Windows 8/8.1 on an ASRock Z77 OC Formula MB. When I look at the SSD where Windows is installed I have three partitions - 300MB (Recovery Partition), 100MB (EFI System Partition) and 111.27GB (Boot,....Partition). Why did the Windows 8 installer create three partitions on the ASRock system? I think I understand the EFI partition since the ASRock BIOS has a "Load UEFI Defaults" option. The Gigabyte MB does not have this option in the BIOS? Is that because the ASRock MB has truly implemented EFI and uses the EFI System Partition to store boot information?
Why was the Recovery Partition created? I built this system from scratch so there is not any third party involvement. If I reinstall Windows 8 using a new - never used SSD will I get the three partitions? If I format the SSD with one partition prior to Installing Windows 8 what will I get?
I not concerned about the loss of 300MB,why I got different partition configurations on fresh installs of Windows 8 on two different MB's/Systems?
View 9 Replies
ADVERTISEMENT
Feb 1, 2014
Why windows 7 and windows 8 introduced a limitation when using Disk Management, and is NOT possible to create more than 3 Primary Partitions? However, using DiskPart from command line it is VERY possible, no warnings or notices.
Code: C:Windowssystem32>diskpartMicrosoft DiskPart version 6.3.9600Copyright (C) 1999-2013 Microsoft Corporation.On computer: PAINKILLERDISKPART> listMicrosoft DiskPart version 6.3.9600DISK [code]....
As far as I know, there is a maximum of 4 Primary partitions on a hardisk, or 3 primary and one extended, and IN the extended partitions more that 4 logical drivers.However, from any disk utility like the old, deprecated, and buggy Partition Magic, acronis disk partition utility, gparted Linux, parted, cfdisk, fdisk, or even on the older Windows like Xp, nt, 2000, 98, me, ms-dos, freedos, I WAS ALWAYS BEEN ABLE TO CREATE 4 PRIMARY PARTITIONS, but with the new WINDOWS 7 and the new WINDOWS 8, it appears this limitation of only 3 PRIMARY PARTITIONS instead of 4. Don't know about Vista as I have skipped that version of windows on every PC that I have build or worked.
Or is working like this because of some hidden reason which I can't figure out by myself what could It be, and the only thing that I can observe is that while technology is evolving (hardware and software), we have limitations like this, to create only 3 primary instead of 4 primary while using Disk Management from administrative tools or right clicking on the computer and "manage" console.
Personally I am a little irritated/annoyed that now the disk management is having "handicap" and I can NOT find a serious reason for this idiocratic limitation. As we are "evolving" the normal path It would be more normal to be able to use more that 4 primary on a hardisk, from my point of view, not limiting to ONLY 3 Primary.
View 9 Replies
View Related
Sep 15, 2014
I am having problems installing UEFI & a Error 0x80004005 with Windows 8.1 OEM saying it can't create partitions for UEFI then creating 2 partitions for MBR installation instead. This using a 400 TB, hard drive, setup with a GPT system & nothing else & ready for Windows 8.1 to create the partitions.
The first time it happened I used MiniTool Partition Wizard Professional, to delete the partitions created by Windows 8.1 & convert the MBR to GPT, then used Wipe Disk function to erase all data and set all the bits to a 1.
The only thing that I can think is upsetting the installation is that I have left the other drives in the system including 1x3 TB drive, 1x2 TB drive and a second 4 TB drive.
The 2 TB drive has "Win 7 Ultimate" installed using MBR, the 3 TB drive is empty but ready to install Windows 8.1 setup with GPT, and the other 4 TB drive has a UEFI Windows 8.1 installed but broken.
I have also tried to install UEFI Win 8.1 on the 3 TB drive but it failed with the same error code as above.
This UEFI takes a lot to get ones head around dose't it, and me being much older than I once was makes it even harder. I have tried this installation at least 3 to 4 times now and doing these "Wipe Disk Functions" every time has so far lost me 3 whole days just in wasted time.
View 1 Replies
View Related
Mar 3, 2012
Ok so i am trying to install windows 8 X64 onto a different hard drive as windows 7 so i can switch between the two at startup.Ok so my problems started yesterday when trying to install windows 8 onto the Hard Drive i was getting"Windows cannot be installed to this disk. The selected disk has an MBR partition table. On EFI systems, Windows can only be installed to GPT disks."To fix this i converted the disk to a GPT disk in Disk ManagerNow im getting the Error "Setup was unable to create a new system partition or locate an existing system partition. See the setup log files for more Information." Here is a screenshot of disk manager at the moment.I am trying to install Windows 8 to Disk 2.
View 9 Replies
View Related
Jun 15, 2014
I'm trying to recreate win 8.1 pro system reserved partition on my ssd. Initially I installed windows on my ssd (c: ) and windows created the sysres partition on my unformatted hd (without telling me anything). After some trouble I managed to be able to boot from ssd directly without going through the sysres partition on the hd. Now if possible I'd like to recreate the sysres on the ssd (by disconnecting my hd so that windows has no other options than creating this on the ssd). If a try a system refresh it tells me it would wipe away all my user installed apps.
View 4 Replies
View Related
May 17, 2014
After entering a valid retail key into the installer located here I get the following error:
I have tried running the installer on another computer with the same results. I have also tried the netsh command and deleting the Panther folder. The problem arised after doing the trick to download 8.1 with a 8 product key and cancelling the 8.1 installer. It was working yesterday and this morning.
View 9 Replies
View Related
Apr 27, 2014
When I get to the part in the Windows 8 installer that it tells me what needs to come to my attention, instead of opening a little browser inside of the program as I guess it's trying to do, it opens up 2 tabs in whatever browser is my default. This would be fine if the buttons in the web pages still modified the actual installer, but they don't and therefore the installer is effectively stopped.
I'm trying to upgrade from Windows 7 to Windows 8. Key word: Upgrade. I would like to avoid re-installing the OS altogether, but I can do that by myself if it comes to that.
Here's what it looks like:
I read on another thread that making IE the default would fix it, but I tried that and it did not work.
View 3 Replies
View Related
Feb 28, 2014
For some reason, Windows 8.1. downloader package refuses to see my 8GB SanDisk flash drive as a target for creating bootable Windows 8.1 installer USB media. A 16GB Patriot drive is detected and processed properly, but 8GB SanDisk is ignored. The same is true for the Windows 7 USB/DVD tool.
What could be causing this?
When I create the media on the 16GB drive, only 3+GB is used, which means that 8GB drive should be sufficiently large.
UPDATE: It appears that the SanDisk drive is not detected as "removable", so neither Windows 8 downloader nor Windows 7 USB/DVD tool see it as a valid target. There are quite a few reports of that issue on the Net. So, how do I create a bootable Windows 8.1 install media from that SanDisk drive?
View 6 Replies
View Related
Mar 7, 2014
I have download all update related with windows 8.1 but all of them in .cab file format
Can I customize windows 8.1 installer and add this update into them?
So I can re-install windows 8.1 with all update file?
View 9 Replies
View Related
Oct 18, 2013
I run 3 HDS. 1 SSD, and 2 normal drives.
I just clean formatted my SSD and installed Windows 8 on it, which I always put on that drive.
However I am seeing a bunch of partitions, 4 recovery partitions. Are these normal? If not, how would I get rid of them?
View 4 Replies
View Related
Aug 3, 2013
I have 2 partitions: System Reserved (100mb) and Windows 8 (465gb). Windows 8 is marked as the system partition while system reserved is marked as Active & Boot. Is there any way I can like split windows 8, copy the files onto the new bit of unallocated space and make that partition the system partition instead of the "old" windows 8 partition?
View 1 Replies
View Related
Oct 8, 2013
I am using the guide to install Windows 8 over two partitions and I get the error:
Windows cannot be installed to this hard disk space. The partition contains one or more dynamic volumes that are not supported for installation. I followed all the steps 100%
Found this Get the paid version of EaseUS Partition Master at discount. Magic Partition Manager Freeware for PC/Server users. Upgrade EaseUS Partition Master Free can I use this to copy partitions?
Worked it all out, the software linked above was able to convert my Dynamic drive to a Basic drive for free!
View 2 Replies
View Related
Aug 6, 2013
I have an pre-installed Windows 8 in my notebook. When I first got the PC, I got only C:/ partition so I needed D:/ and for doing this I used EaseUS Partition Manager. This is just a guess but I guess Windows can't find those recover partitions that are in my HDD. I haven't deleted those partitions just created D:/ and here is a screenshot I just take to show you the partitions I have.
I have already tried copying the Install.wim from my BIOS_RVY partition which was about 9GB and I moved it to C:/WinRec and used this command as I saw it from internet : reagentc.exe /setosimage /path C:WinRec /target c:Windows /Index 1 But i still get the error:
"Insert media some files are missing. Your Windows installation or recovery medial will provide these files."
This method didn't worked so any other too. I wonder how can I refresh or some sort of return my notebook to the factory settings from the recovery parts I have.
View 9 Replies
View Related
Jan 27, 2014
I recently decided to buy an ultrabook and I got me this one: LG Z360-7416, with a ssd and windows 8 (x64). As usual, it came with a lot of garbage installed which was using almost half of the ssd storage (128GB), so I decided to do a clean install. I got me a msdnaa copy of the windows 8.1 pro (x64). So, i used a pendrive to boot up on UEFI mode and selected custom install and when i get to the select partition, it shows everything fine, i select a partition and when a click on install, it returns an error saying it cannot install on my partition (i dont remember exactly what it says), and when i click on refresh, all my partitions vanishes, even going into the prompt and using diskpart doesnt show my partitions anymore. I tried to load some drivers, but it didnt work.
I was only able to install windows 7(x64), where nothing of these things happens, it installs realy easy. I tried to install windows 8 from windows 7, like an upgrade, but after it restarts, it gets stuck also. My disk is formatted on GPT, as im using EUFI on my windows 7 installation.
Tried almost a hundred times using all solutions i found online, but always the same result. And to get even more weird, some rare times it gets to the installation part, where it says the progress, but stays on 0% of unpacking files...
Its seens to be missing some especific driver to windows 8 be able to work with my ssd, but i cant get it right, but if it came installed with windows 8, it must be a way to make then work together.
Unfortunately i deleted the recovery partitions, so im stuck on windows 7.
View 1 Replies
View Related
Jan 6, 2013
I have Windows 8,W7,Wxp working well in multiboot. But i have Windows 8 instaled in C:but it is the 2nd partition.How can i move it to first partition ?W7 and wxp are probably on the 1st D: partition.
View 2 Replies
View Related
Jul 17, 2013
I'm mostly a Linux user, but I recently bought a laptop with Windows 8 on it. After a few days dual booting I decided it wasn't for me, so I decided to delete the windows partitions and usa just Linux. I would like, however, to keep the recovery partition, so to be able to easily reinstall Windows again if I felt like I needed to, but I'm not sure what partitions should I keep. Here's a picture of my hard drive partitions as of now:
Do I need more than the restore partition? Can I get rid of the boot one? What about the recovery one? And the one flagged msftres?
View 1 Replies
View Related
Feb 10, 2013
I dual booted win 7 n 8. now i am running out of space in the drive which contains Windows 8.
Win 7 is installed on C drive and Windows 8 on D drive. How can i interchange the OS on the drive. I want to install win7 on Drive D and Windows 8 on Drive C.
View 2 Replies
View Related
Sep 2, 2013
I've got a HDD currently using MBR that has 2 partitions.
Code: DISK 1:Partition 1 - C: (System)Partition 2 - D: (Data)
At the moment I'm using Win 8 on the MBR HDD and I would like to convert to GPT without losing data stored on partition 2. I'll be reinstalling Win 8 on partition 1 so I can take advantage of UEFI.
View 3 Replies
View Related
Sep 15, 2014
I had a 17 GB unallocated partition. I changed it to a Primary partition. It is empty. Can I merge it with the C: partition ? Picture--- edit--- A picture---
View 9 Replies
View Related
Jan 14, 2014
using the UEFI install instructions from this forum. I do meet all of the requirements (Windows 8 64-bit iso, ASRock Z87 Extreme4 mobo, blank SSD). When I get to Step 7 in the UEFI guide, I only get 2 partitions instead of the 4 shown(Recovery, System, MSR, Primary). I only get System and Primary. I decided to delete all partitions and just run the setup on the unallocated drive...everything worked fine. I am just wondering what the consequences are of not having those 4 partitions. I still have the UEFI interface when I boot up so it appear that is working.
View 3 Replies
View Related
May 29, 2014
Protecting partitions from factory reset?
View 1 Replies
View Related
May 15, 2014
I have a very peculiar issue; after using various disk imaging tools such as Macrium and Paragon, my boot partitions seem to be strangely corrupted. The effects of this corruption are:
1) Plain-text boot menu instead of the new graphical boot menu,
2) Long delays before the boot menu is shown,
3) Even longer delays when doing native VHD boot, after choosing the boot entry from the menu.
I have done a lot of testing and experimentation, and on a virgin fresh installed system from the Windows 8.1 setup ISO, these symptoms do not appear. Only after I have imaged the system using the imaging tools above, do these symptoms start appearing. Unfortunately, just copying my main Windows C: partition using the same imaging tools re-creates the same issue. So I cannot rely on these partitioning tools.
I need a way - a set of commands - to re-create the boot partitions, re-initialize their BCD stores, etc. so that I can normally boot from my C: partition, as well as native VHD boot.
Needless to say, I want to avoid having to completely reinstall Windows on my C: partition, as that would be extremely time and effort prohibitive, if I only knew how to re-create and/or re-initialize just the boot partitions in question.
View 9 Replies
View Related
Oct 27, 2013
Recently I got my new laptop running under Windows 8.1 and was surprised with how the partitions were sized.
Here is the screenshot from the DiskManagement:
So I shrank the size of C: disk as you can see and got unallocated space. I want to attach that space to D: disk. I thought that is possible to extend recovery partition to unallocated space, then shrank recovery partition, and newly appeared unallocated then attach to D:/ disk. But failed with that.
I don't think that I really need those 900Mb and 350Mb recovery partitions and that they are useful, but it would be unwise to delete them while I don't know what are they for. Latter 20Gb recovery partition at the picture at least has the significant size to store something
View 9 Replies
View Related
Jan 13, 2013
How to hid all the partitions in the factory installed HDD for Lenovo Y580.
This is the scenario.
Firstly, i successfully migrated all of the following partitions:
OEM/Hidden partition,
C partition: boot drive/ program files and data drive &
D partition: containing drivers
from my Lenovo factory installed HDD to the SSD and to use the SSD as the primary boot drive . Now, i plan to use the factory installed HDD as my data drive. (I am using a caddy tray for this whereby i plan to swap out the optical drive and pluck in the Lenovo factory installed HDD). However, for "safety reasons" i do not plan to re-format the entire factory installed HDD but rather to keep those partitions just in case if my SSD fails.
Hence, how do i turn all the three partitions above (in the Lenovo factory installed HDD) to become dormant? I want the computer to boot up from the existing SSD but then to treat the factory installed HDD as the data drive and not to read from any of the three partitions in the factory installed HDD.
I am planning to use EASUS as my disk partition freeware.
View 1 Replies
View Related
Dec 4, 2013
Purchased a new laptop . It has one large C 1T drive . I would like to create 4 primary partitions , one for programs, one for data , another for media , and the rest unallocated.
How to use built in disk manager ? Can I create several partitions at one go?
Is it easier to use a 3rd party partition software?
View 3 Replies
View Related
Sep 15, 2014
I have a Windows 8 pro oem copy and I want to create a bootable Windows 8.1 pro Usb stick in uefi format to do a clean install.
Now I built my machine myself so I am sure there is no embedded windows key in the bios? But I cant seem to download anything that will create the media, it says it my key wont work in a retail copy of windows 8.
View 3 Replies
View Related
Jul 16, 2013
I don't know what Windows 8.1 has done to my system but after getting rid of it and re-installing Windows 8 ENTERPRISE again I cannot create Windows to GO any more
It doesn't matter if I plug in an SSD, a standard USB stick or a standard external USB HDD - I get No suitable devices found when launching the application from the control panel.
(I can do it manually the old fashioned way but I don't know why the standard method is broken when it was working perfectly before).
View 2 Replies
View Related
Sep 15, 2014
I'm trying to get my existing installation of windows to boot as an external hard drive. I had it installed on an internal drive, then removed the hard drive and put it in an external enclosure. Then trying to boot off the drive results in windows loading the recovery screen and giving me a bunch of options. The only thing I can do is restart the computer with all the other options (refresh, reinstall) saying that the drive is locked. Putting the drive back into the computer will allow me to boot normally from it, but I want to be able to boot from it via USB 3.
What can I do to either create a fresh install of windows on this drive that can be booted by usb or migrate/modify my existing installation to work.
View 3 Replies
View Related
Dec 22, 2013
I need the steps for create partitions aligned in 1024.
View 5 Replies
View Related
Aug 5, 2014
Brand new laptop. HP. 17e UEFI +GPT etc. Upgraded to 8.1 from 8, first thing. Then clicked on the MS, create recovery. (in blind hope of a clean 8.1 restore). Inserted (32gb stick) (later found out is illegal windows 8 version, that is not removable.) SD-extreme, 32gb. list on toms HW, as winner of all, (and is useless for this app).
So I pull out my very old SD cruiser glide, 32gb (old , slow and not win 8 cert (a good thing). Yes all 32gb extremes are mapped as HDD not removable media and is doomed. (known on all forums) but same error.
The cruiser shows up i device manager under removable media....btw i want to find out why the missing files error. I have a HDD and SSD, with latter mirrored. both the orig, HDD fails and SSD fails. same way. I parked the HDD , and run only SSD. but both fail... (my guess is , upgrades 8.0 to windows 8.1 is cause).
now the screen,
attached
How can i find the log of these errors, it's not in event viewer.. oddly. sfc/ scannow works. as does chkdsk, and restore (create) works,. and system is Fast a lightning. All HP apps works, cept there version of create disk for same reasons.
My HP create recovery now works on the GLIDE. (old very old 32gb stick i had laying about). So now I am thinking HP? blocks the MS create so you will use theirs? But I'd lilke to know this, what files are missing....
View 9 Replies
View Related
May 16, 2014
Trying to create an ISO of the windows 8.1 dvd. I want to make a bootable USB stick when I go to install it to speed things up and make a backup copy. I can create the ISO using Alcohol 120 but when I use the Windows 7 USB/DVD tool to open the ISO it says it is not a valid ISO file.
Every other bit of software can read it okay so it is an ISO file as far as I can tell.
View 9 Replies
View Related
