Maintenance :: Power Saver Settings Option Windows 8?
Aug 30, 2013
Use of the Power Saver Setting in Windows 8 lowers my pc temperature (at idle) by at least 6 degrees. Using this setting, my pc now idles at 27 degrees C. When I use High Performance, my idle temp is usually at least 33 degrees, or more. For those who have problems with their pc's running warm, this is just one of the things I've found which works for temperature lowering. My biggest impact on lowering temp was air cleaning the pc case interior - getting all the fuzzy balls out...... At one point, my idle temp was in the 50 to 60 degree range and I figured my disk was failing. After checking for a possible problem, I found much of the problem was my own maintenance procedure failure. So, if your pc seems to be running rather high, look around for the simple solutions - clean pc, use power settings, etc.
My windows 8 laptop no longer allows me to select an option out of Power Saver, Balanced, High Performance, Power4Gear Battery Saving, and Power4Gear High Performance. It is set to High Performance, and any time I try to click another option it immediately returns to High Performance.
I've been trying to change my power options. I go into Power Saver, "change plan settings," and try to change the "On battery" setting from "Put the computer to sleep: 3 minutes" to "Put the computer to sleep: Never." (I want to make this change because I have a Dell XPS, and it can have difficulties waking up from sleep.)
I've made this change a number of times, but after a while my computer simply reverts back to the 3 minute setting on its own. So, I leave the machine alone for a few minutes, I come back, and it's asleep...even though I thought I had changed the setting to 30 minutes. And in fact, I *had* changed the setting to 30 minutes; the computer is somehow reverting to 3 minutes on its own.
I'm currently experiencing this issue and it's really annoying. I just bought this laptop for 2 months and it's been working fine. Then suddenly this problem started yesterday. Generally every time I open up a game my laptop will automatically switch to Power saver mode and it causes some lags in the game. At this point I would Alt+Tab to desktop and switch it to "High Performance". Here's the annoying part, even though I have set it back to "High Performance", the laptop still works as it in "Power saver" mode, I can tell because the game is still laggy and slow. I tried to restart the laptop and experienced the same issue. I ran a Full scan by using Avast Internet Security 2014 and didn't detect any problem at all. What should I do?
I recently upgraded to Windows 8 (64-bit) and noticed I don't have power options available. I own an HP Pavilion DV7, usually when I leave the laptop to do something over night, I go into "Choose what closing the lid does" and I get the error saying my power plan info is not available. Whenever I try to create a powerplan it tells me the same thing, but when I hit next, it tells me it can't find the file specified. I have no power options at the moment. I tried resetting to defaults using cmd, rebooted, and the only power option I had (Razer Gamebooster) was gone, and had nothing after.
I build out tons of machines of all makes and models for demo scenarios. One of the things that is the same on all devices is our custom power settings.
Is there a way to copy the power settings and apply them to any new laptop we build out?
Example:
Laptop 1: Power settings are set to never go to sleep, not require passwords on wake up, brightness set to max, disable adaptive brightness.
I am hoping to be able to run a batch file or something to accomplish this on every machine I build out.
I just had my laptop install Windows 8.1 tonight. It's a clean install, by the way. Now the problem is I noticed that every time I restart my laptop it's power plan reverts back to "power saver", I had it set on "high performance" before. I own a Samsung laptop, model is NP535U3C-A01, Series 5.
I was wondering how Power Plans work. Say, I have my Power Plan set on Balanced. Now it'll adapt to the Balanced settings for plugged and unplugged respectively.
my computer needs more power for a task I'm performing while I'm not plugged in. Will it be able to push itself to it's capabilities, or would it stay restricted? How about when it's plugged in?
If I would rather have "High Performance" settings when I'm plugged in, and "Balanced" when I'm not, is there a way to do that? It's clear that Power Plans work even while being plugged in, but I see no need to limit the PC while you aren't on battery.
I have hp notebook with windows 8 OS. When I plugged in the charger the display totally disappears and the screen has black for only 1, 2 seconds. And the same situation is when i removed the charger. But this is not happened when i was using windows 7. Is this a problem or a feature of windows 8.
The Troubleshoot icon that should be under the 'Advanced Startup' Option is missing. System is a new Dell Latitude 10 ST2 Tablet running Windows 8. Have access to 9 other identical tablets, all configured the same and they all have the Troubleshoot Option. Have tried multiple methods of getting to "Advanced Startup" display (including Safe mode, 'shutdown /r /o', etc.), but all result in only having the 'Continue', 'Use a Device', and 'Turn Off your PC' options - No Troubleshoot. Other than missing this icon, system is working fine. Shy of wiping the disk and starting over.
I recently purchased a DVP8 and I love this thing. Problem is, it suffers from wifi issues in that once it goes to sleep, the wifi automatically goes to "limited" and I need to retoggle the wifi setting to get it connected. I've tried all kinds of fixes - uninstall windows updates and reinstalling drivers, but to no avail.
So I basically said screw it, and set "sleep mode" to never on the power management option, and no more wifi issues. Seems like the wifi doesn't reactive properly when coming out to sleep mode. My question is - will this damage the tablet in the long run? In terms of battery life, I would think the main factor is the screen on time. I can just turn the screen off with a tap of the power button. Is there really that big of a difference?
My PC ignores all power settings and hibernates after approx 5 minutes of user inactivity. It is a Dell Vostro 200, which I had been running successfully on Windows 8 Pro. The problem appears to have been the result of upgrading to Windows 8.1.
Regardless of the power scheme settings, the PC goes into hibernation after 5 minutes of "inactivity"; i.e. if there is no user keyboard or mouse input. The hibernation also ignores most background processes, so it will go into hibernation even if I am streaming internet radio. I use Windows Home Server, and the daily backup process is currently failing because the PC wakes up to start the backup, but hibernates after 5 minutes, in the middle of the backup process.
The only exception I can find is YouTube - hibernation does not occur if I watch a video longer than 5 minutes, even if there is no user input.
I have tried various suggestions from other forums, without success:
The video drivers up to date.
BIOS is up to date, and ACPI is set to S3.
I have run power settings troubleshooter which reset power settings to "Balanced".
I have tried setting power to "Always on"
I have tried a clean boot process, disabling all start ups and other services, but the problem still occurs As noted above, the PC was previously working fine, and the only change I can identify is applying the Windows 8.1 upgrade.
I cannot seem to access the bios at all with windows 8.1 and my gtx 780 ti. When I connect the hdmi to my gtx 670, I can see the bios screen and can change the config but with the hdmi in my 780 ti I get a black screen until the dual boot windows selection. I've disable fast boot and what else to do.
My screensaver and power setting to turn off the display has stopped working, and these were working the other day. The only thing I have changed is I updated iTunes. I have tried a system restore to before this and this did not fix this.
Among other things I have tried a clean boot, sfc, and checking the energy report. Clean boot did nothing and sfc gave no errors. I uploaded my energy report if any one thinks it could be useful.
I also tried to put the PC into sleep, which I don't normally do and it woke up a little while later. That gave me the following error in event viewer:
The system firmware has changed the processor's memory type range registers (MTRRs) across a sleep state transition (S4). This can result in reduced resume performance.
I have turned sleep mode off in power settings and turned off requirement for password yet after no activity within a very short space of time I am required to log back in. How do I disable these functions for good ??
I have a number of different drives that I use for different purposes but I only use two of them frequently.I would like for the others to enter sleep mode when not in use, but never my main two. Is there any way to edit power saving settings for individual drives?
Why Plan Settings and 'Advanced Power Options' configuration differs from each other?
My plan Settings sets the time to sleep with computer plugged in to 25minutes whereas the advanced power options has it on 180 minutes. Same applies to other options of the power options.
I was wondering what this mess is all about? I restored both to default and set the advanced to 'Never' and manually configure the Plan Settings.
I am situated where I have to see my computer screen whether I am working on my computer or not, and so because the light hurts my eyes it needs to turn off the screen when I am not using it.
I used to be able to get the screen to turn off after a couple of minutes, and it would go black. But now for some reason I cannot get it to work.
These are my settings:
Control Panel/Power Options
Power Saver button is ticked.
Set on:
Turn off the display 1 minute
Put the computer to sleep 1 minute
Right click computer screen/Personalize Clicked on Screen Saver and chose BLANK and Wait 1 minute On resume display log on screen is not ticked.
When using a screensaver that is suppose to have a transparent background (be able to see what is on the desktop) it defaults to the background color chosen for the start screen theme.
An easy example is the bubbles screensaver that comes preloaded, the weird thing is when selected and you preview it, it previews with a transparent background you are able to see what is on your desktop, but when you let it run its time and it pops up on its own it replaces the background with the color theme you chose for your start screen.
How to change it to remain transparent? I've tried changing the background color of the start screen to transparent with Decor8 but the screensaver background still is not transparent.
Attached are the images of how it should look and how it actually looks.
I went into my power options to change some of the advanced settings and most of them are missing? I am on windows 8.1 with a week old Surface Pro 3. I want to say I read somewhere that hyper-v can cause options to be missing, but I honestly don't even know what that is and I don't have it installed.
In the future I'm planning to build a new computer to replace this old hunk of junk and I'm curious as to one thing as I'm not entirely sure on this. Just how safe is using the High Performance Power Plan in Windows 8.1?
You see, my current rig is running an old i5 661, normally on the Balanced Power Plan on an old ASUS P7P55D-E Deluxe Motherboard with a GTX 660 and 4GB of RAM on 32-bit Windows 8.1.
But my future plan is to use an i5 4690K with a Corsair H110 All In One Water Cooler for CPU Cooling on a Z97 Motherboard and 8GB of RAM in 64-bit Windows 8.1.
I'm hoping to get quite a bit of performance on this next computer cause hey... I'm planning on using it for gaming and such. But also web browsing and chatting with friends. I hear how High performance is suggested for 'optimising' Windows 8.1 but how much safer is it...
And how much of a performance increase could I possibly see in comparison to the old rig?
After installing 8.1, pushing the power button on my venue pro 11, no longer wakes it up. I have to hold the button several times before it finally restarts. Ive read this could be due to an update. It did not do this before 8.1.
I actually wanted a confirmation dialog box to shutdown when i press power button (physical) but I didn't got any luck so, im trying to trigger a application (shutdown apps) when a physical power button is pressed. if there is any hack or tweak which satisfies my need to prevent windows 8 directly shutting down when power button is pressed.
I am looking for registry editor or any other script to fulfill my need.
I was attempting to enable my system protection in order to allow me to restore individual files to a previous state. Unfortunately when I go to do so the option is not available at all.
I found a registry trick that is supposed to add an option to "delete on reboot" when you right click a file. To allow you to schedule files to be deleted when the computer restarts (incase they are currently in use and cant be). The registry edit looks like this:
Windows Registry Editor Version 5.00
[HKEY_CLASSES_ROOT*shellDelete on rebootcommand]@="CMD /E:OFF /C REG ADD HKEY_LOCAL_MACHINESOFTWAREMicrosoftWindowsCurrentversionRunOnce /v "Del %1 OnNextReboot" /d ^"cmd.exe /c DEL /F /Q "%1"" /f""
[Code]....
A: how to edit the registry to make this trick work in windows 8 too.or if not possible B: how to remove the registry edit and take away the broken "delete on reboot option"
I got my new ASUS laptop on Mother's Day this year, and the first event happened a week later. I've had this same event happen 6 times since then as shown by the attached image.
I'm comfortable with computers but am not an IT person so I'm not comfortable performing tasks within my system unless I know what the heck I'm doing or why.
W7 forum said overclocking (it's not), heat (this last time it had been in sleep mode while I was out and within moments of waking it up it crashed), sudden loss of power (it's plugged in AND has 100% battery left) and so on. In other words, it doesn't appear to be related to any of those things. It just randomly happens.
1) why this keeps happening and
2) how to fix it?
I've been very disappointed in my new laptop since getting it; I've NEVER had such issues with a new computer before..and I thoroughly dislike Windows 8 and I doubt I'm alone in that view.
I'm looking for a way to automatically shutdown PC at midnight and turn it back on at 16h during work days (while I'm at work). Is there a way to do that in the built-in scheduler or is there an app for that?
