Hardware Drivers :: Easiest Method To Update BIOS?
Dec 16, 2013This is my motherboard: Motherboards - MAXIMUS VI FORMULA
I am trying to update the BIOS, but don't know how. What is the easiest method to update the BIOS?
This is my motherboard: Motherboards - MAXIMUS VI FORMULA
I am trying to update the BIOS, but don't know how. What is the easiest method to update the BIOS?
When startup pc (black screen) massage displayed" Please insert correct disk" message exact forgot. Next a few second this is massage displayed:"Please floppy disk insert to drive A" again massage exact forgot.
Will be updated via USB BIOS . What should I do to prepare a USB?
This issue has been an ongoing one about close to a year after i purchased my PC. It is an ASUS PC when i go to the support site for updates in the past and now for my model i see BIOS updates.
Lately they have been all CAP Bios's,any time i try to use these type of BIOS's it is not recognized in the BIOS utility in the BIOS screen.
My last BIOS update was a ROM BIOS it worked fine, now all the future BIOS updates on ASUS's site are CAP.
If I try to rename the BIOS to a ROM i get an error "image integrity check failed". Of course i have spoken to ASUS Support in the past and now over the phone also, but no luck.
I do know it can be risky updating a BIOS if anything goes wrong the PC will become unstable or unusable.
Most will say unless there is not something in the BIOS update that will make improvements to the PC.
It has been 4 or so BIOS updates since one i have on this PC so far on ASUS's site.
I believe my motherboard is not compatible with a CAP BIOS, but why ASUS lists them for my PC.
I have lenovo g580 cori7 and installing windows8 64bit. I tried to update the bios but i got this just like the screen shot.
Now my labtop working on legacy mode and I am not comfort with this mode.
After updating the BIOS to A09 Windows 8 won't boot anymore.
The BSOD reports an issue with winload.efi and error code 0XC0000001.
How to find and run this file with DOS.
The file is burned to a cd-r like this folder: drivers/bios dos/ then the files are inside that folder called flash.
But it is a bios update file so what I would need to type to run it.
I have Samsung slate xe700t1a and recently downloaded and installed the lates bios from Samsung. After the installation the machine rebooted and all I get is black screen. Not even the Samsung logo, just the blue power led light comes on. I have tried all the button combo boot up power windows key, vol up and down and nothing can't even access the bios. I contacted support and that was a waste of time. Maybe removing ssd drive and connecting using mini sata to sata cable on my pc.
View 2 Replies View RelatedIt has an ASUS M2N-E motherboard with an old single core AMD Athlon 64 (I cannot remember which model specifically).
Last week, I provided him with a couple of old HDDs and 8GB worth PC-5300 DDR2 667 MHz RAM. We also installed Windows 8.1 64-bit, and other than the CPU being a single core and a bit slow, things were proceeding relatively smoothly.
He has an NVIDIA Geforce 8500 on the board, and he's ordered a PNY-made Geforce GTX 650 that's on it's way at present.
He's wanting to upgrade the CPU to the AMD PHENOM X4 9950, so we've been periodically meeting over the past couple of weeks to perform surgery on this old machine.
At any rate, we found that to update the CPU, we needed to update his BIOS from the one that was installed, which was at revision 0502. The needed BIOS revision for the CPU was 1504, but would also work with revision 1701.
After jumping through several hoops to update the BIOS, we updated it to 1701. However, since then the machine will not boot into Windows 8.1. He gets an instant BSOD. I did not see the error code, so I cannot say what it was. He told me that he's attempted to do a repair install to no avail. The repair attempt results in a constant loop of the machine rebooting and BSODing.
At any rate, here are some URLs that detail the board specs and the list of BIOS revisions for that board.
Motherboard Specs: Motherboards - M2N-E - ASUS
CPU Compatibility list: ASUSTeK Computer Inc. -Support- CPU Support M2N-E
the " toshiba service station " recommended an update called " bios update version 1.50 for qosmio x70/75 " and they said it is recommended so i did download and he said dont remove the cord or anything so i did that and installed it and everything was going smoothly but when he finished the update and was restarting it shut down and didnt boot up again. whenever i click the power button the keyboards and power button lits up for a second and then the laptop shuts down it is windows 8 and it does not boot up for me to go into the bios menu
View 8 Replies View RelatedTrying to address a different problem, Gigabyte suggested that I update the BIOS on my GA-F2A88X-D3H mb from F1 to F3. In addition to not solving the problem, after I updated the image displayed on my monitor--Dell 2209 WA--doesn't fill the screen. Everything's there, but the image stops about 3.5" short of the right bezel.
Using AMD's Catalyst Control Center hasn't worked. I've read some posts about a similar--the same?--issue that suggest changing a setting in "My Flat Panel Display." But I see only "My VGA Display," with no option for over- or under-scanning.
The image does display fully on rebooting--I see the Gigabyte UltraDurable logo, and on entering BIOS instead of going into Windows 8.1 (64-bit).
Since first writing this, I've tried the monitor's menu and other buttons without success.
Is it worth getting a DVI-D to DVI-D cable to connect digitally, in place of the current VGA connection?
Does it signify that the monitor reports a screen resolution exceeding its supposed maximum of 1680 x 1050, namely, 1920 x 1080? In both Windows screen resolution and AMD CCC, I'm unable to set a resolution above 1680 x 1050, and setting lower resolutions doesn't work.
I am willing to update ram of my laptop.I have a question after latest bios update i.e A13 can i upgrade my notebook's ram upto 16 GB?
View 3 Replies View RelatedI am on my laptop at the moment and am trying to make a BIOS update stick for flashing my main desktop at home that has an Asus P8Z77-V board.
Now I have downloaded and saved both the BIOS utility - renamer and the BIOS version itself and both are zipped files.
I have tried using 7-zip to rename that BIOS file which the manual tells me I have to do but to get it to work when I use the 7-zip it goes to choose an app from the store. Now I have never fully understood zipping and unzipping files to be able to use the application and now this message has got me even more perplexed as to what to do!
I did try this at home on the main machine but I did go round in circles on that (7) machine and until I get the BIOS ready on the stick I cannot flash the BIOS on that main machine.
I tried updating to Windows 8.1 Update 1 and in didn't go through properly (it hard froze and crashed) and now won't boot past the BIOS. I cannot get into Windows and I cannot get into the Recovery Menu.
I tried recovery USB's and any I create either from a 3rd party or Windows itself results in loading to a black screen with a mouse cursor. Only one worked, Acronis (probably because its Linux) and it showed all the drives ruling out a hardware issue but sadly it cannot repair Windows.
So it seems I might be a victim of the black screen issue some had when moving to Update 1.... BUT the difference is I cannot boot into the recovery menu at all and any recovery media boots to a black screen.
How to get out of this screen and actually boot into anything which will allow me to try to fix the MBR or go back to a restore point.
I thought the point of recovery software was that it loads no matter how corrupted Windows is... obviously not! Something is stopping all of them booting properly.
A while ago I tried to put a new HDD in my laptop and got a message saying something a long the lines that the disk wasn't recognised (forgot exact message)
I took the computer to my computer repair shop and they installed the HDD I asked them if it would be easy for me to do it and they said yes it was just a case of resetting the BIOS.
how to reset the BIOS so I can install a new HDD?
I've installed HDD's in windows 7 machines and it was just a case of inserting the disk- I didn't have to mess with the BIOS!
I have a Lenovo G510 i7(which does not seem fantastically faster than my celeron Samsung R530!). I have replaced the DVD with a SSD. I have cloned the HDD to the SSD, made changes in the BIOS(changed to ACHI,switched to Legacy, put the SSD first in boot) but get the message "no bootable device insert disc and press any key". If I use UEFI I do not see the SSD. I have googled this until my finders are sore to no avail. How to boot from the SSD and once I can do this can I reformat the HDD? The SSD is called A:, the HDD C:. I cannot change the drive letters.
View 9 Replies View RelatedI have a Samsung DP700A3D All-In-One. It came preinstalled with Windows 8. I remember it being version 6.2 (?). I always seem to try things above and beyond my skill set (Current Computer Science student). I installed Ubuntu 13.04 64 bit alongside Windows 8 with no problems. I aloud the Ubuntu to do the partioning. It used Grub2 for bootloader. I wasn't happy with that wanting to use Windows Boot Manager. After changing this and reloading that, somehow the windows 8 partition did a recovery. I can now not boot anything. I'm currently on Ubuntu live CD. I can see the drives from here. There are partitions labeled SAMSUNG_REC, SAMSUNG_REC2, 487 GB Volume(Windows files inside), Windows RE tools, and 481 GB Volume(Ubuntu files inside). When I boot the machine, I get the Install Boot Media ?? comment at attempted start-up. When I was setting up the Ubuntu alongside Windows I could access BIOS(?) with an F2 press at initial flash screen. Now I cannot. I can do nothing but run the Ubuntu Live CD. I don't want to try Fresh install of Ubuntu because there are files on Ubuntu partition because there are files that are too large for me to back-up else where that are very important. I KNOW .... BACK-UP BACK-UP BACK-UP!! It however is too late for that..
View 4 Replies View RelatedI have been trouble with a few bsod problems and i was instructed to change my ram timings to 9-9-9-24 so i did and i also changed my frquency to 1333 but hen when i go into cpu-z i get different results or is this the same.
View 8 Replies View RelatedI have bought me a new computer with a ASUS Sabertooth V2.0 GEN 3 motherboard with UEDI BIOS utility.
I want it to start at 9 in the morning.
Some time ago I replaced an IDE hard drive with Windows 8 installed for an SSD drive onto which I installed Windows 7. I would like to know if I can temporarily swap back to the IDE drive (Windows 8) while I obtain the Windows Product Key (embedded in BIOS apparently) and then replace the SSD drive (Windows 7), or boot from an external docking station and if so how do I do that?I am totally confused about the BIOS. Does a different OS change the BIOS details?
View 5 Replies View Relatedhow to change my BIOS into UEFI. I tried to flash a UEFI BIOS file attached on Acer website but it wont start flashing. The latest version of UEFI installer is not responding when I want to flash it, the older version said I need to have the same type of BIOS installed. how to install UEFI on my system?
View 9 Replies View RelatedI have recently built a new computer and installed Windows 8. All was running fine (including USB devices such as iPhone, flash drive etc), however since upgrading to Windows 8.1, none of my USB devices are showing up at all. Oddly, the mouse and keyboard still work.
When I go into the BIOS, all my devices (iPhone, Flash drive, keyboard and mouse etc) all show up in there, so I'm guessing it's a driver/Windows 8.1 issue that I'm missing?
I have been to the ASUS website and downloaded all the drivers I can find, but still no luck.
My motherboard is an "Asus Z97 Pro". I have tried contacting Asus support, but they are completely useless!
Ever since switching to AHCI mode, I've noticed that my keyboard has issues with the volume wheel not working properly. Also after setting up the LED lighting on the keyboard and a few restarts later, I've notice that when restarting my system the keyboard LED, blue in this case, will automatically show up and when it does, and I use the del key to get into BIOS doesn't work. I have to move the the usb connection to a different port, restart and keyboard LED will be white. This time using the del key, I can get into my BIOS no problem. This never happened when I was using native IDE mode.
View 1 Replies View RelatedEvery few weeks, I have to get my old graphics card and change the BIOS settings because the CSM mode just resets out of nowhere. The new graphics card isn't compatible with windows 8 so I have to go back and enable the CSM settings to get it to work. Is there a reason why my BIOS keeps resetting the next morning I wake up?
View 3 Replies View RelatedI have a CM6730 Asus PC with a P8H61-M PRO/CM6630 motherboard.
I was having problems getting good Graphics performance and the topic of Integrated vs discrete GPU came up, the options in the BIOS were set to use iGPU, since then I do not get the option on boot to enter the BIOS.
I have tried ASUS but they want me to send the unit in for repair.
My rig has Windows 8.1 fully updated.
I can't enter my BIOS/UEFI after activating "MSI Fast Boot" in the BIOS/UEFI.
I read somewhere about "GO2BIOS",but my installation disk didn't came with that software.
MB: H81M-E34 (MSI Global H81M-E34)
Went to boot up my Acer this evening to no avail. I can see it start to cycle through searching the DVD drive and see the read/right red LED light for the hard drive go on for about 5 seconds, then nothing. No BIOS test pass beep. I know that it beeps once for passing, then continues to boot.
I took the side panel off and reseated all the connections including the Mem strips. At one time I left a strip out intentionally for a continuous beep, which is what it's suppose to do.
My PC specs: Asus P8Z77-V with a SATA2 WD Caviar Black 500GB. The HDD has four partitions, and I've had Windows 7 32 bit installed on C:/ for three years. Windows 8 was just installed four months ago.
Before this, I had my Windows 8 and BIOS ahci-enabled C:/Windows 7 <> D:/Stuffs <> E:/Windows 8 <> F:/Stuffs
Yesterday, I needed some space on my F:, so I started Partition Wizard (I used this program a lot before with no problems) and cut 9gb from C, after that queue it to extend F: that much space.
Because C: is located first, but F: is located last, PW created 4 queue, which is cut -> move D: -> move E: -> extend F. The two first actions were performed fine, however when I restart as PW promoted, I was stuck at the BIOS, unable to access BIOS, with the red led lit on the P8z77-v, which means there was a problem with a boot device. If I unplug the HDD, the system goes into BIOS just fine, but obviously can't boot anymore.
There is a lot of important data on that disk which I can't afford to lose. My problem sounds almost like the same as this one: [URL] ....., however when he changes his BIOS to IDE mode, his HDD booted into Windows 7. However, mine doesn't. I've disabled Secure Boot, but that doesn't work either. It just stucks at the BIOS splash screen.
Currently I am considering to burn a PW CD and hotswap the HDD in order to fix the MBR and stuffs.
I was reading that your Intel motherboard drivers should be updated. I watched the video and it seemed so easy. It said you can run it even if your mobo is not Intel with no harm done. The target to do so is below.
I am only an average pc user. Is updating the mobo drivers as important as was being stressed and is it a rather fool proof procedure.
|MG| Intel Chipset Device Software (Formerly Chipset Software Installation Utility) 9.3.0.1026 Download
I found several windows 8.1 activation methods in forum but which one is the best and most safe?
(I need something like Daz windows 7 loader that was clean and great)
KMspico
or
kms vl all
or
slmgr.vbs -ipk <KEY>
slmgr /skms <KMS SERVER>
slmgr.vbs -ato
or ...
PS : KMSpico create some processes, and would load my cpu?
Over the last couple days, I built a new PC and installed windows 8.1. Initially I had some issues installing windows, so I unplugged all my drives except the SSD and DVD. I installed windows to my SSD.
Everything works great!
Now I started adding my drives back in 1 at a time. When I plugged my 2nd SSD in, it showed up in BIOS, but not in Disk Management or Device Manager. So I booted back into the install CD, it showed up in the disk manager there. Since this was also a blank SSD, I partitioned and formated the drive from the install CD, then exited the installer and booted back to my windows drive.
I have 2 SSD drives working great!
Now to add my 2TB HDD... Same issue, it shows up in BIOS and the install disc, but not in Disk Management or Device Manager. This drive does not have a boot partition on it, however, it does have two existing data partitions. They were made from my previous windows 7 system and the option to delete these partitions is grayed out in the install disc menu. I also have some data that I would like to keep on it. I have a USB dock that I can use to read the contents of the disk just fine. Everything is there and in working order.
What is different about Windows 8.1 that is preventing my hard drives from showing up in windows proper? I am reading things about UEFI online, but nothing seems to fit my exact scenario. I will try and post some screen shots when I get back at it.
System:
Mobo- Asrock Fatal1ty Killer z87
CPU- i3 4330
GPU- Gigabyte 660 OC
SSDs - Kingston V300 120GB
Windows 8.1 64bit
Windows 8 has suddenly stopped to recognise my friends keyboard. Mashing Shift-F8 seems to let the keyboard work (for several minutes). All drivers are up to date, works perfectly in Safemode and BIOS. I have reinstalled windows 8 (its only used for web browsing) and nothing has worked. It is a Toshiba Satellite.
View 1 Replies View Related