Win 7 Installation Could Not Detect Any Hdd
Nov 9, 2009
I currently have a computer running Vista 32bit Ultimate and purchased the Windows 7 Home Premium Upgrade.
When I used both the 64bit or the 32bit DVD to boot, I would get stuck at the STARTING WINDOWS screen for around 30min. After I will then be able to get to the install windows screen. Since I want to Upgrade from 32bit to 64bit, my option is only the CUSTOME/Clean install.
HOWEVER, when it ask me where I want to install the windows to, windows 7 installation could not detect any hdd. I am guessing this is why the STARTING WINDOWS screen took 30min load, as it was looking for a hdd.
In the same screen, it does have an option to load a driver.
So, I went to Asus to d/l the vista 64bit sata driver and also tryed the WD sata driver for the Raptor hdd.
The WD driver would not even show up on the floppy, and the Asus did.
Loaded the Asus sata driver, and still no hdd detected.
The computer is currently running with this HDD in Vista32bit and is seen on the bios. This is the only hdd in this computer, I really don't want to waste money to buy a slower hdd for my computer as the Raptor is 10k rpm.]
Note: I do not care about any data or problem in this hdd, I just formated teh hdd and did a clean
P.S. Windows 7 Upgrade Advisor tested and all hardware are ok.
MB: Asus Striker Extreme
Hdd: WD Raptors 150gb
View 4 Replies
ADVERTISEMENT
Jun 2, 2012
I'm having some problems with my win7 installation.
As mentioned in the title the main installation will not detect the SSD and is asking for drivers, however, it is detected in diskpart.
The SSD is detected in BIOS, by ubuntu setup, linux mint setup, win7 setup's diskpart. I've ran the diskpart cleaning and reformatting and just cleaning to no avail.
The SSD works perfectly fine and I previously installed Linux Mint on it since win7 setup would not detect it besides in diskpart. I've tried adding the SATA drivers to the installation but that doesn't give me any result either, everywhere I check it's either "do the diskpart thing" or "drive's broken".
Setup:
Asus Sabertooth Z77
i5-2500k
Patriot Pyro SE 250GB
View 5 Replies
View Related
Apr 12, 2012
Just built a moderate spec gaming PC from scratch, and all has went according to plan except when I try to install Windows 7, my hard drive won't show up. My new motherboard doesn't have any IDE slots, but I only have an IDE hard drive. I am using a 'Pluscom Serial ATA PCI Adapter' to connect my hard drive to the computer as it has 1 IDE slot on it. I don't have a disc for drivers and don't know where to start. I am running Ubuntu on it at the moment so I can download any drivers I may need.
View 9 Replies
View Related
May 14, 2009
Install everything, the bios detect the hard drive (it's a new hard drive, never been use) but when installing the Windows 7 64, the hard drive list is empty.
Here my spec
Phenom II 940BE | Gigabyte 790X-UD4P | Seagate Barracuda 7200.12 500GB | XFX HD4770 512MB | OCZ StealthXStream 600W | NZXT Tempest
View 2 Replies
View Related
Jun 19, 2010
I have a 2.8 Ghz, P4 processor with 768 (512 + 256) MB ram and an Asus p5rd1-vm motherboard with a 128 MB ATI-Radeon Graphics Card. I have been running Windows XP for years. I have decided to upgrade to Windows 7 finally after reading all the reviews. However, During installation, my hard disk is not being detected (There is no drive on screen which I can format or set up on.) Can anyone help? Do I need to update my BIOS?Also, I recently changed my hard disk (upgraded it) and XP has been installed and is running fine.
View 3 Replies
View Related
Sep 13, 2009
I am installing Windows 7 (Custom installation initiated from Windows XP) but I get the following error message when the installation is on the "Installing updates" step of the installation:
"Setup cannot continue due to a corrupted installation file. Contact the vendor of your Windows installation disc or your system administrator for assistance."
Do you have any idea what the problem may be with the installation? Is there a way to see what file that may be corrupted?
I have tried to burn the DVD in low speed, but the error appears anyway. I have a MSI K8T Neo2-Fir mainboard and the Windows 7 upgrade advisor application says that my hardware is okay for upgrading.
View 9 Replies
View Related
Jun 2, 2011
I have just got Windows 7 Ultimate.I accept the Licence Agreement, set my partitions as i want them but when it gets to the expanding files part it will hang at 0%. This happens on both the 32 & 64 bit disc.This is a brand new purchase which I opened it about an hour ago.The laptop has a 400GB HD and 2GB of ram. It came with Home Prem x64 pre-installed, So the hardware meets the requirements.What seems to be the problem?
View 9 Replies
View Related
Jun 29, 2011
I just bought a new hard drive and a brand new Windows 7 Home Premium 64bit disc and I am doing a clean install on the new hard drive. it seems that everything is going normal, but at a random time during the installation, the computer just shuts off.sometimes it doesn't even get to the installation when it shuts off. sometimes it shuts off in the middle of the "windows is loading files..." black screen. there are no beeps when it shuts off or when I turn it back on. there are also no error codes.whenever i turn it back on it simply acts as if it never tried to install windows and starts the boot all over from the disc
View 9 Replies
View Related
May 16, 2012
So i have a new SSD Corsair Force 3 240 gig and all I want to do is install Windows 7 Pro on it. This board does not support parted magic (cannot wake from sleep and there are no onboard video to wake up to) so ive resorted to clean all.I have not been able to successfully boot the OS on the SSD. I never intended on setting up raid but apparently all the literature i see is on raid. I created a USB install disk as reccomended onto a 8gig ntfs primary active did the bootsect /nt60 X: and it successfully worked copied the cd over to the flash drive and copied the rste drivers in a folder called drivers My SSD is installed on port 1 6gig sata intel (as this board doesnt have marvel apparrently) My DVD is installed on 3gig Sata port 6 I set up Raid in the bios as reccomended by others (as this is the only way to install ssd?).
Nothing UEFI is enabled There are no other drives hooked up to the computer. Just SSD, USB cordless mouse, keyboard and no network cord or WIFI i started with a clean ssd as reccomended my bios recognized the ssd on post i booted into the win 7 install (MBR not uefi) i loaded the 64 bit rste drivers from asus as reccomended by others i left the machine to install the usb then booted into windows install (for whatever reason) i pushed f8 to boot my corsair windows brings up an error on a black screen File: windows/system32/drivers/adpahci.sys driver did not load Status: oxc0000221 Info: Windows Failed to load because of a critical system driver is missing or corrupt
View 2 Replies
View Related
Nov 25, 2011
Can you help me with the instruction to detect if my os is x64 or x84.
View 3 Replies
View Related
Jan 11, 2012
my computer can't detect any of my usb. I follow the instruction by erasing the USB devices and it turn out that even my mouse can't detect by the computer,,now i'm using my keyboard to search the net because even if i use other mouse it can't be detected..please help me,,really need your help tnx. I'm using a WINDOW 7 64bit.
View 2 Replies
View Related
Jan 17, 2013
i have a toshiba satellite c660 with windows 7 installed , cannot detect wifi
View 4 Replies
View Related
Dec 31, 2012
Just upgraded my laptop (Samsung NPC300E4C) from windows 7 starter to windows 7 ultimate.But problem is that it cannot detect SM BUS CONTROLLER on windows device manager.
check Farbar Service Scanner.
Farbar Service Scanner Version: 23-12-2012
Ran by Mike (administrator) on 31-12-2012 at 21:50:03
Running from "C:UsersMikeAppDataLocalMicrosoftWindowsTemporary Internet FilesContent.IE51G9GP7W0"
Windows 7 Ultimate (X64)
Boot Mode: Normal
[code]....
View 3 Replies
View Related
Jan 10, 2009
I am running the beta on a Dell M1530 (laptop) and it just won't recognize the second monitor at all. I was running dual-monitors just fine on Vista.
View 9 Replies
View Related
Mar 7, 2010
I've had a second monitor set up for a while now, but havn't been using it much, i tried to use my second display tonight and its displaying no signal, the second monitor isn't even detecting in windows at all now, nvidia control panal will not detect it even when you try force it, its not in the devices, won't detect through the right click > screen resolutions thing either, its just like its not even connected.
Only changes i have made to computer lately was updating to the latest drivers as i got bad company 2, i tried going back to the old drivers i had and still same problem.
Im using x64 win 7 genuine version, geforce 9800gtx+, 24" acer and 32" LG screens, have had this setup working before, i plugged in the new screen and it worked straight away i didn't have to do anything, now its like its no longer detecting its plugged in, i've tried many restarts, i've tried swapping the plugs around and still can't get it to detect.
View 8 Replies
View Related
Jul 3, 2010
I have just recently decided to upgrade all my pc's at home to Windows 7 Home Premium. I have purchased a Windows Home 7 Premium Family pack that allows 3 installations on the one license. I have tried installing it on my pc running a legal copy of Windows XP Media Centre Edition and it cannot detect my hdd.The PC itself is an Acer Aspire E500. I believe the motherboard running it is an ECS RC410-Mr (V1.0), has a Seagate Barracuda 250gb Sata Hdd and everything else is pretty much standard.So here's what is happening. I have put the installation disk into the DVd-rom and booted up my pc. It loads all of the default files etc and goes into the standard process to select the install location.It doesn't detect a hdd. So I figure at this point that i must have to load drivers for any on-board sata raid or something. Weird thing is i don't remember it having this option. I have looked into the bios to find if there is any low level Raid settings and there is no mention of it.I have gone onto the ECS website to find drivers for such a thing and they do exist. I have put them onto a thumb drive and re-ran the installation. It detects the driver, I click load and it says it is not compatible. I have tried multiple sources of this driver and none of them work.
I have heard stories about having to do a bios update but I worry about this on 2 levels 1) the pc works fine and I dont want to risk killing it, 2) the bios updates dont say anything about a fix for Windows 7 or the raid controller.Am I going about this the right way or is there something I have overlooked?
View 3 Replies
View Related
Jan 9, 2012
one of my user's laptop wireless is working properly until the laptop can't see any wireless. i already checked the settings of the laptop, even if the wireless is set to broadcast, i cant see or connect to any wireless..under control panel > network and internet > network and sharing center, on the left side of the screen i can't see the option "manage wireless settings". that's why i cant add any SSID of the router. i already checked the drivers and update it but still theres no wireless detected. when i run the windows troubleshoot i got this error saying "windows could'nt automatically bind the ip protocol stack to the network adapter".
View 2 Replies
View Related
Dec 27, 2011
my laptop cant detect any usb.
View 1 Replies
View Related
Mar 24, 2012
I recently bought a game called Tales of Monkey Island. It can be played in PC and Mac. I put the dvd game in but it won't even play the cd as it keep popping out saying please insert a disk which i already have. I tested it out on my friends Mac and it seems perfectly fine
View 3 Replies
View Related
Feb 17, 2010
Windows has stopped this device because it has reported problems. (Code 43)
View 1 Replies
View Related
Aug 22, 2012
can,t detect the DVD ROM in win7 OS IN Toshiba C660 173 model
View 1 Replies
View Related
Oct 28, 2009
I just built my PC (first one, sounded like a good idea at the time) and was told that getting the latest drivers would "fix" this issue. Problem is, I haven't had a PC or really been on the net since 2001, (don't laugh) so.....I don't know how to get the "right" ones. I realize that i've built something waaaayyy over my head/experience level, so now I just want to learn all that I can.
View 6 Replies
View Related
Jun 4, 2011
For some unknown reason realtek drivers can't detect my mic and thinks that I am using speakers (I'm using headset) no idea how to fixed this , google whole day couldn't find anything , tried uninstalling , installing new drivers , tried windows drivers no luck, here's a screenshot maybe someone could help me out , I tried out Game booster software and defragmented my c:/ hard then I noticed the problem with my mic. I am running windows 7 64x ,also I've tested my mic on my laptop it works fine with windows 7(x32) default drivers...
View 7 Replies
View Related
Mar 25, 2011
I have posted in other forums with no luck.I bought a Samsung SH-D162D DVD Drive in a USB enclosure to connect to my Toshiba laptop via USB.I cannot get windows 7 to find it! When I plug in the USB cable the balloon comes up to say it has been installed (sometimes), I can see it on for about 1 or 2 minutes then it drops off. It isnt listed in my hardware or anything.Its not found in Disk Management or My Devices so it isnt a case of changing the drive letter - i cant find the drive to change it.I have also tried to find the upper and lower settings in regedit....couldnt find them so couldnt delete them as advised in other posts of this nature.It is set to master, the IDE connector and power connectors are fine. Its gotta be a windows 7 problem cause it does show up very breifly. In the minute or 2 its there I cant do anything with it...it just hangs although it will open and close. Ive googled it and cant find anything.Ive also connected it up to another laptop with XP and had no problems so I know the DVD Rom works fine and all the cables are ok.Ive tried in all 4 USB ports on my laptop and also turned off all energy settings...all with no luck. And I also have EVERY windows 7 update.
Heres exactly what happens from power off on the enclosure.
1 - I plug in the USB lead then turn on power to the enclosure.
2 - I quickly go to Start, and I can see the DVD Rom drive E next to my laptops dvd rom.
3 - The green bar at the top starts filling up from left to right and gets about half way then suddenly the DVD Rom icon disappears and so does the green bar.
4 - It then flashes up under the laptops DVD Rom icon with a Local Disk drive E but only for a split second.
5 - Sometimes a balloon comes up saying installing device, then device successfully installed...but not every time.
View 1 Replies
View Related
Oct 26, 2011
Just formatted my system after it was invaded with some trojans. But now, AVG doesn't detect any viruses or malware at all, yet when I open Task Manager, my system CPU usage is hovering from 77-100 percent. Computer is running really slowly too.
View 6 Replies
View Related
Aug 10, 2009
I just purchased a dv7-1261wm and installed Windows 7. But in Device Manager, it shows 5 drivers that didn't install. There are 4 listed as "Base System Device" and 1 as "Unknown Device". I've installed all the drivers from HP's site, but that didn't help.
The main issue though is the CD/DVD/Blu-Ray Rom drive doesn't detect in any burning programs. It shows as installed fine, but burning programs can't access it.
View 1 Replies
View Related
Jul 20, 2009
So, I upgraded from 32-bit Vista to Windows 7 RC. All went well, except for my computer now only detects (under Display Adapters) a Standard VGA Adapter. I have a Dell XPS M1530 notebook, and it came with a nVidia GeForce card, I believe it was a GeForce 8600M GT. I right-clicked and told it to check for hardware changes, but it will not detect the graphics card.
Because of this, it is not displaying any of the Aero effects, etc, and my second monitor is not receiving any signal although it is properly connected.
Does anyone know how I would be able to fix this?
View 5 Replies
View Related
May 12, 2009
I just installed the RC and have been trying everything I can to get it to detect my second monitor. Both monitors are identical and worked in the pre RC version of Windows 7 with absolutely no issues.
I used the Nvidia drivers from Windows update as well as the ones from the Nvidia site. Both will not show my second monitor.
If I switch the cables it works on the other monitor no problem.. It just will NOT detect it when they are both plugged in.
View 1 Replies
View Related
Jun 15, 2011
I have recently installed Windows 7 Ultimate 32bit, but when i inserted my Compaq Wireless adapter (network receiver or whatever it's called), USB, to connect my computer to my wireless network, windows doesn't detect it. It has worked fine on Windows XP on the very same computer, but now - nothing.
View 1 Replies
View Related
Jul 14, 2011
I recently bought a TP-LINK TL-WN350GD wireless network card, inserted it into a PCI-E slot and installed the drivers, but can't seem to get it to work. It appears in Device Manager as 'Atheros AR5007G Wireless Network Adapter' and apparently 'this device is working properly', but infuriatingly it won't detect any wireless networks. I've tried using the drivers that Windows 7 installed automatically and also the drivers that came on the disk with it, but all to no avail. When I troubleshoot the card, I get the message that 'there might be a problem with the driver for the Wireless Network Connection 2 adapter', but this is all I can find. It's especially irritating as I picked the (admittedly lower-end) card because it's definitely compatible with Windows 7 (I already tried one which wasn't).My PC has Windows 7 64-bit, has an AMD Athlon 4600 dual core CPU and 2 gigs of RAM.
View 9 Replies
View Related
May 18, 2012
Is there a way we can detect a person has used his pen drive in our PC Windows 7 without our permission? Can a person deletes the traces also after using his pen drive?
View 9 Replies
View Related