Recover Windows 7 From Hp Recovery System?
Aug 1, 2012
I decided to recover the windows and I haven't made the recovery disc yet, so I will recover from from windows directly from hp recovery systemI just want to know how many times can I use this option for later?
View 3 Replies
ADVERTISEMENT
Apr 18, 2012
my 5 month old computer would no longer boot, it automatically ran start up repair, after about 6 hours said could not repair, took me to restore, but then said couldn't restore due to I/O error, tried recovery option with data back up with disks but get fail due to I/O error, tried again on the complete factory restore and got error of not enough memory to complete. can I recover my system?
View 9 Replies
View Related
Jan 31, 2013
I do not know how or why but some files that I have been using were just gone when I went to find them. The files where in a word document with other files which are still there.
View 3 Replies
View Related
Apr 14, 2011
I have my netbook dual-boot WinXP and Windows 7. (I used EasyBCD for the dual-boot setup.)In booting into Windows 7, I used to have the option of the "repair your computer", which brought one several useful tools, if there is problem booting.Of course, the exact same tools are on the Windows 7 setup DVD, which I have. However, with a netbook, I don't always have the USB DVD drive with me, or the DVD, and that recovery stuff boots up much faster from the HDD partition, than from the DVD. So I think it is good to have.(Not at all like the notebook manufacturers recovery partitions. I wouldn't want to use those at all, wiping out all my data.)Recently I upgraded to a larger HDD. I used Acronis to clone my old HDD (at that time in the notebook) to the new HDD (attached via USB enclosure). (It was an older Acronis version, long predating Windows 7. I don't know if I would have had better results with a new version.)Well, at first I could not boot at all, with the new HDD installed. I was able to fix that though. (I forget the details of it at the moment.)Also, my drive letters (I have four partitions-drives) were messed up, so somehow the Acronis cloning did not keep that information, and I had to fix that in both XP and 7, with Disk Management.For the most part though, my partitions were all intact in the new drive. Being a larger HDD, I increased the size of a couple, in the Acronis interface.I realize now though, that I do not have the recovery boot-up option any more. That can show up while booting into Windows 7 and pressing a key, but if one chooses it, it just tells one to put in the Windows 7 DVD. Therefore, that option of booting from the recovery partition seems to be gone.Looking in Disk Management from Win 7, I see an unallocated partition, I think about 8.98 GB, I think. Is that the Windows 7 recovery partition? Did Acronis copy it correctly, but somehow the boot sector on the new drive cannot access it?
View 9 Replies
View Related
Aug 9, 2012
I'm trying to restore my computer to computer factory settings?I've made the 4 discs, but every time it tells me to insert the next disc (not even the number). I've inserted in all 4 of them and none of them seem to get the recovery to continue.Is there a way to recover from the partition?
View 14 Replies
View Related
Nov 3, 2011
I have a Gateway T-1625 laptop. it has 2 gb of ram, 500 gb hdd, and an amd turion 64x2 processor. It came with win vista and am trying to upgrade to win7. I ran the disk, everything seemed to go fine, all the way up to setting the time and date. After the restart, it goes to "System Recovery Options" and asks for language. Next screen says "select an operating system to repair and click next. Only win vista operating systems are listed and can be repaired". My problem now is only win7 is listed. My options are to load drivers or next. I have read in a few places to load drivers, but i read them after trying to install win 7. I don't know where to look for drivers if that might be the case. If i click next, i get the "choose a recovery tool" and it states the operating system is win7 located on (C Local Disk. I have tried the startup recovery several times to no avail. When i look at the details, there are 10 problem signatures. The ones that look odd to me are the "Signature 1 SystemDisk" and "Signature 6 OsVersionMismatch". Like most idiots, i thought i could handle a simple installation and didn't bother to look for tips before hand, and now it's costing me.
View 14 Replies
View Related
Feb 25, 2011
I am attempting to run a complete system recovery (factory restore) on Windows 7 using a recovery partition. Last time I ran the recovery, I ended up having a lot of problems with system programs not being installed correctly, and with the system administrator account. Now, when I reboot and use the F8 option to bring up the boot options, I do not have an option to "Repair your computer" as I had before. I also tried rstrui.exe through the command prompt, but it only tells me that "No restore points have been created on your computer's drive. To create a restore point open System Protection."
I also checked my drives through DISKPART to make sure there were no problems with the recovery partition, but it is showing up normal. On the Windows knowledge database it said that if the system recovery options are missing, then the system is not installed with the options or they were disabled by the network administrator. Given that I had no problems accessing these the last time I ran the recovery, I'm assuming something happened with the account. I am set up with 1 user in the system, which is the administrator.
1) Re-enabling the options so that I can access the "Repair your computer" options on the boot menu.
2) Run the system recovery options without having to get into the bootup menu.
View 14 Replies
View Related
Dec 28, 2012
I can not start windows 7, and i try to restore to an earlier point in time, and it says i've not enough free space in C:. I tried using command Prompt to delete files from C, but it looks stuck in X:. I entered x:>cd "C:" and it says C: and after X:>
View 2 Replies
View Related
Sep 10, 2011
Recently I was attacked with malware and I had no internet security. It messed up some programs, changed the description of processes etc. I read up on how to get rid of malware and such, and I got Malwarebytes, SpyBot - search&destroy, and finally Avast! computer antivirus. After running scans with malwarebytes and Spybot, removing all the trojans and programs that were affected, I used ccleaner to clean the registry. Although I did all that, it seems like there is still something in my computer because spybot keeps scanning the same files over and over, and both Malwarebytes and Avast! keep saying that a malware threat had been stopped, while showing a URL that I never even connected to. Sometimes it even happends when internet explorer is off. what I really want to do is to restore my PC to the factory settings and start with a fresh NEW system. I'll make sure to get AVAST right away to insure security. As for backing up files, I'm afraid that the virus would somehow be in certain files and infect my computer again. Nothing really important that I'd lose. So I don't really mind so much to do a full factory reset.
View 9 Replies
View Related
Mar 21, 2011
I want to have a Factory Reset of my computer. In order to launch a System Recovery, I need to create Restore Discs. When I launch the Recovery Disc Creation, it says:"This computer does not have a burning drive, which is required to make DVDs. Please contact HP Support for asistance."My computer did not come with a build in CD Drive. Even plugging in a USB CD Drive will not make creating the discs possible. So. I ask you. How can I reset my computer to Factory Condition?
Computer Specs:
Windows 7 Home Premium (64-Bit)
Model: HP Pavillion dm3 Notebook PC
edit: This notebook came with a Recovery Partition built in.
View 4 Replies
View Related
Jul 4, 2010
My HP Pavilion DV7 laptop will not do a system recovery after I hit F11 when I boot the PC.The recovery drive on my computer says it's just about full.It's running windows 7 64-bit
View 9 Replies
View Related
Aug 11, 2012
if my operating system like xp or win 7 is corrupted/damaged which it can't be started to get/recover my files what software should i use
View 4 Replies
View Related
Oct 17, 2012
I attempt to do a system restore from several dates, keep getting recoveryunsuccessfull, what do I try next ?
View 2 Replies
View Related
Jun 13, 2012
Honestly don't know y I deleted it but, I was cleaning files from my drives while in Linux and I deleted the system volume folder from one of my hdds and now all my data is inaccessible. Haven't touched the drive since, would like a surefire way to get it back. Here is my set up64gb ssd Windows 7 1tb hdd internal (deleted system volume folder) 1tb external hdd 50gb Linux partition 950gb ntfs partition
View 2 Replies
View Related
Oct 8, 2012
my son wiped out my operating system on my gatewaylaptop, can u help to get it back
View 2 Replies
View Related
Feb 22, 2013
I have a Dell XPS 17 laptop that has dual drives - c & d.The c drive crashed and was replaced by dell.We are now trying to do a system image recovery from the d drive.We are following How to do a System Image Recovery in Window7 from seven forums.com.url...After Selecting the System Image from the D Drive (STEP TWO, # 5 and 6), the computer prompts to create a repair disk.The only way to move forward is to create or not create the disk.In either case, it then has you restart the machine, takes you through the process again.. Step 5/6.Never gets to Step 7 to actually DO the System Recover.
View 4 Replies
View Related
Jan 5, 2012
i have vaio laptop when i get it ,it was contain only local disk(C) so i made shrink to create another logical derive (D)so, when i recovered my laptop after that i lost (D)?
View 1 Replies
View Related
Jul 23, 2012
My neighbor was having issues with their laptop and since I'm a bit more tech savvy I'm attempting to fix it for them. The laptop is a Toshiba Satellite L505d-S5983. Its about 3 years old. They had an issue with the laptop and now whenever it starts up windows it shows an error screen that gives error f3-f200-0002. Apparently this can happen to Toshiba laptops. Seems there is a corrupt Windows 7 file and I need to do a system restore. There are no system partitions to do a back up of. I burned a disc on another laptop of the Windows 7 System Recovery Environment and changed the boot drive to the disk drive in the BIOS. Now it loads the disc and loads up the Windows 7 System Recovery Environment. The problem now is it doesn't detect a Windows installation. It gives me an option to load a driver from c:WindowsSystem32 to detect the Windows installation, but I don't know which file has information about the Windows install.
View 5 Replies
View Related
Oct 27, 2011
I am familiar with System Restore, selecting earlier times, and the often-available option of undoing a System Restore. But I found out (too late) that according to Microsoft, System Restore done in Safe Mode is not able to be undone.I lost 1,000's of photos doing the system restore, now the only restore point option visible is what I believe to be the new one after I did the restore. Prior to me doing the System Restore, there were a number of times from me to choose from, I just chose one that was 10 days ago. Is there any software, method, or hack that I can use or do to recover the thousands of photos that were on my desktop and that were in folders on my desktop? It's a 1 TB HD?
View 1 Replies
View Related
Feb 10, 2012
my issue is with windows 7 giving me an error message on boot up. I started having a google redirect issue on my dell laptop the other day. I though I had taken care of it with malwarebites, but suddenly while I am surfing the net the screen goes completley black and I am faced with a blue screen of death. Can't start anything. Safe mode, system repair, and system restore either freeze or get the same blue screen of death.I finally end up using the Dell system local backup that is a preloaded recovery tool on their computers, and the two burned recovery discs I made with it when I first got the pc. Using this I restore the PC to its factory setting wiping out my old files and partitions. It works! and I go through setting up windows like the first time. It loads up and is working fine. I load on some anti spyware programs scan my computer, set up the internet, and start updating windows.Once I dowload my updates and restart my computer the computer will not boot windows. I get a error that goes something like this Windows failed to start. A Recent hardware or software change might be the cause. To fix the problem:
1. Insert your windows installation disc and restart your computer.
2. Choose your langugae settings, and then click next
3. Click "repair your computer."
Status: 0xc000000e Info: The boot selection failed because a required device is inaccessible.I cant get safe mode to work. Basically my only option is to stick my recovery disk back in and repeat a factory fresh recovery and that gets my computer back working, but every time I turn it off I get the boot error. It is frustrating because I can get it to work fine otherwise. Right now I am just putting my laptop to sleep mode but I would like to be able to turn it it off without recovering windows each time!If you have any ideas that could help me that would be great. I am thinking there is some sort of lingering software/hardware incompatibility or the virus/malware altered something to make the boot up process change. I feel like there is something I could probably do or run in windows to fix this. For awhile I was thinking my hard drive was messed up, but if that was the case I would assume I would not be able to recover windows and load anti virus software on it and have everything be normal, only to not have windows restart.
View 6 Replies
View Related
Sep 18, 2011
I have a hp g62-231nr laptop and it broke before sent it out, got it fixed and everything was great. about four or five months go by and one night i was playing games on the laptop, the laptop died plugged it in and went to sleep. woke up in the morning to a black screen says media cable something something no bootable device please insert bootable disc and press any key. I downloaded the windows 7 system repair disc and popped it in it loads up says there is no operating system and load drivers cant find any drivers but there is a hard drive disk named Boot (x and two removable devices, the system repair disc in the dvd drive and removable device C. I cancel and press next and be brought into system recovery menu I click on startup repair or system repair. It tries to find problems than says cannot repair windows automatically I click details and this is in the white box.
Problem Signature:
Problem Event Name: StartupRepairOffline
Problem Signature 01: 0.0.0.0
Problem Signature 02: 0.0.0.0
Problem Signature 03: unknown
Problem Signature 04: 0
Problem Signature 05: unknown
Problem Signature 06: 1
Problem Signature 07: unknown
OS Version: 6.1.7600.2.0.0.256.1
Locale ID: 1033
I exit out and cannot do system restore memory test is 100% ok. BIOS system diagnoic says error code 03f0 Hard Drive Not Exist the main BIOS menu says the BIOS system is idle. Version for BIOS system F.17 i tried the recovery disks but it says that windows does not support the media on this device. I also have an .iso file of windows 7 home premium dvd but it doesn't do anything so im thinking its a bad .iso copy of windows somehow or I burned it wrong maybe? If there's any other information needed i will gladly post it just ask. also I cannot get to logon screen on startup. The hard drive makes the same soft spinning sound not beeping or anything. I need this computer for work its a business laptop. also i cannot access system recovery from F11 the words show up in bottom left corner on startup but even if you repeated hit f11 or hold it down it brings screen to black screen media cable failure check cable exiting pxe-rom..no operating system etc.
View 2 Replies
View Related
Jan 4, 2013
Replaced my HD and used my Win Image BU, but Win will not start. I get the Dell screen that says Windows is loading, but then it is a blank screen.I did a second restore with same outcome. I followed System Image Recovery exactly, but cannot get that last screen to restore files I have booted from USB and from the boot disc - same results.
View 1 Replies
View Related
Sep 18, 2010
I bought a new computer where Windows 7 is already pre-installed on partition C:. In addition I want now to install a second "test" Windows 7 system on new primary partition. And a logical "data" partition. At startup I want to choose later between the 2 Windows 7 systems which one I want to boot.
When I inspect now the current partition table (before changing it) it looks like:
1.) "Recovery" 10 GB Primary MBR NTFS
2.) "System Reserved" 100 MB Primary NTFS, Active, System
3.) "Local Volume" 30 GB Primary MBR NTFS Boot
4.) Unallocated
As you can I have a problem: If I create a new, 4 th primary, bootable partition with 30 GB into the "unallocated" space, then all maximum 4 primary partitions are filled. I cannot create a 5 th primary partition which contains the logical "data" partition. So I guess I must either destroy "Recovery" or "System Reserved" primary partition to have one more primary partition slot available.
Now what for are the "Recovery" and the "System reserved" partition? I don't know them from WinXP. Are they Windows 7 specific? Or are they "inventions" from the computer manufacturer (Sony)? Is "Recovery" absolutely necessary? Why is "System Reserved" active? From I WinXP I know only partitions as active which hold the OS and not some kind of "pre-boot-partitions"
View 2 Replies
View Related
Dec 16, 2009
Yesterday I installed Windows 7 on my computer and everything worked perfect the internet, music, etc... The problem is that when i resterted some screen said: System Recovery Options and I couldn't use the computer so installed W-7 again but now I'm afraid to shut down my computer because I don't want to re-install it again and again. What can I do to no get the System recovery options screen. My computer is a Gateway.
This is what the System Recovery Options screen says:
1. Select language
2. Select an [COLOR=#0072bc !important][COLOR=#0072bc !important]operating [COLOR=#0072bc !important]system[/COLOR][/COLOR][/COLOR] to repair and click Next. (I clicked Windows 7)
3. Password
4. (Then the screen) SYSTEM RECOVERY OPTIONS which includes the options of doing Startup Repair, System Restore, Windows Complete PC Restore, Windows Memory Diagnostic Tool, [COLOR=#0072bc !important][COLOR=#0072bc !important]Command [COLOR=#0072bc !important]Prompt[/COLOR][/COLOR][/COLOR], Recovery Manager.
I've done it 3 times and it doesn't work. and I'm getting tired of re-installing.
View 5 Replies
View Related
Oct 13, 2012
I have a Toshiba laptop in which I installed my copy of Windows 7. Recently, it has not been able to boot: it just restarts when trying to. I tried the typical things:booting to safe mode, etc. but they all do the same. So I tried to sin the System Recovery Options, first from the Advanced Boot Options menu and then directly from my Windows 7 disk. In all these cases, the program gets stuck after selecting the "Repair Your Computer" option, as in this picture:The mouse keeps working fine, but all I can see is the background image, and no window pops up. I know that it is supposed to prompt me to select my windows installation, but that window never comes up. A similar thing happens when I try to install windows instead. It just never gets to the next step.Is there anything that anyone can think of that I could do to solve this problem?
View 1 Replies
View Related
Aug 3, 2011
I have an Asus G73 laptop that I am wanting to do a system recovery on. It works but it's very qwirky and has occasional lock ups. Somehow, one of the automatic Windows updates that was installed deleted all of my old restore points, all the way back to when I first bought the thing. Anyway, I can't get it to burn a full set of recovery disks which is apparently not that uncommon with these machine. Asus actualy responded to an inquiry I sent them (although it takes like, two weeks to get each reply. The dialog has been going on for weeks). They told me to go ahead and do the F9 on start up and tell it to restore the OS partition.
- Asus recommended that I just do the "restore Windows to first partition only". This will leave the other partitions as is. I have a second partition that is for data, games, etc. There is also a third partition that is for MS Office 2010 if I ever decided to purchase the program and activate it. I have all the Office software I need from work so I don't need this third partition. Actualy what I would like to do is just have one large partition with everything on it, including the recovery directory and the OS, restored back to exactly like it was the day I got it. Can this be done with the F9 on start up method?
View 5 Replies
View Related
Nov 21, 2012
Can i still use the CD that came with the motherboard to install Windows 7 if i change my ssd and CPU?
View 6 Replies
View Related
Dec 23, 2012
Windows 7 will not start, System recovery has not worked
View 15 Replies
View Related
Jul 7, 2012
I decided to do a system recovery for my laptop. I've already done a couple of experiments before and from what I remember the first time I done a system recovery, the partition where my personal files where saved did not get deleted.The only thing that was "system recovered" was the partition where the OS was located. Yesterday, I again decided to do a recovery but this time, the partition where I have my files got deleted and the space it had "returned" to the OS partition. Orignally, I shrunk the OS partition so that I can have space for my partition for my personal files.If it helps, I've done a "system recovery" but saw one of it has a "mini system recovery" option. What is the difference?
View 1 Replies
View Related
Dec 17, 2011
I recently created a new partition with 200GB of space on my Windows 7 64bit (HP Elite) PC system. I installed Windows XP Professional on that new partition (trying to create dual OS). After Windows XP was installed, I was unable to find "Windows 7" as a boot option under "Startup and Recovery"... I could only see Windows XP Professional. I went to Disk Management and right clicked on the partition where my Windows 7 OS was under, and chose "Make partition active"... I got a warning system MAY not be able to boot, but I chose to proceed anyways. I tried restarting and got an error "BOOTMGR is missing / Press Ctrl+Alt+Del to restart" ... I tried pressing F11 after restarting to get into "System Recovery" but it would go directly to the error message. I was still be able to access everything else during boot except "System Recovery" such as BIOS, etc.
I re-installed Windows XP Professional on the same partition... and was now able to get into the Windows XP Pro OS again. I'm still unable to access "System Recovery" when booting. F11 option is being bypassed and going directly into XP OS. This is my first concern, how do I get "System Recovery" to get working again? It used to work before as I re-installed Windows 7 couple of months ago. I can still see "FACTORY IMAGE" drive in My Computer (could be on a different drive letter than before). And second, how do I boot to my original Windows 7 OS (C-drive seems intact and all Win-7 system files are there)?
View 2 Replies
View Related
Aug 26, 2011
I just partitioned my C drive and now have an I: drive that I use for data, music and movies and such. My question is this: if I have to do a system recovery. Will I lose that partition? Or will Windows 7 re-install on the C: drive without touching that partition?
View 6 Replies
View Related