Windows 7 Ultra64 + 4TB RAID0 = Failed Installation
Sep 14, 2010
The BIOS is currently set mostly for defaults/auto except for where I needed to specify RAID for the respective SATA ports connected to the two drives I want to stripe and to boot from CD for Windows 7 installation so I adjusted these settings accordingly.The motherboard has an onboard AMD 890FX based RAID controller. I have two 2TB SATA3 drives configured for RAID0 using the onboard RAID controller software. The RAID controller software reports slightly over 4TB as logical drive #1. Everything seems fine at this point.Next step: Boot from the DVD to install Windows 7 Ultra 64. This attempt is a clean install, full (non-upgrade) version, to be installed onto a 4TB RAID0 array using two brand new HDDs.During the installation I supply the device drivers as specified by the mobo's owner's manual. Windows7 installation accepts them no problem. Suddenly, there is a problem... Instead of showing the available drivespace as just under 4TB, after the RAID hardware driver is supplied the list will then show two partitions, one barely over 3TB and another one roughly 1 TB. It does not show one 4TB drive after the driver has been provided from the mobo's driver CD.If I continue to install on the 3+TB drive anyway, the installation routine seems to go through the usual motions... But then comes up with an error... Something about not being able to prepare the drive for booting and to try to re-run the installation program again. It always ends at the same point with the same errror. I will post the exact error message after I give it another try. I should've written it down already, but it's no problem for me to re-create it.So... If someone posts that Windows 7 cannot be installed on a 4TB partition for whatever reason, like it cannot address over 3+TB of drivespace or other reason, then I can just forget about using the two drives in a RAID0 array and use them as 2 single drives.
View 3 Replies
ADVERTISEMENT
Nov 18, 2011
Whenever I try to install Windows 7 SP1 it fails. I've searched all over the web to find a fix and nothing has worked. I thought I'd come here since you guys always helped me with other issues.
View 4 Replies
View Related
Jan 10, 2011
I was trying to install Widows 7 ultimate (32 bit) on Sony VAIO CS-14G laptop. But the installation was a failure. Error occured during process of expansion of packages during setup. Then i restarted and in the boot menu it was showing windows setup. when i entered, it messeged starting windows (like normally it says during starting of windows 7), and then it showed the messege "Setup cannot be completed" and the system restarted. I have following queries (Note: i was not using the dvd during above installation process and i was doing it from setup files copied on a different partition of hard drive. Now,
1. When I inserted the disc, clicked on Install . I got the following error:When i try to use dvd it gives messege "Load Driver: A required CD/DVD drive device driver is missing....."
2. Setup has created a drive called as X:
How do i remove the windows setup files and also from boot menu.
View 5 Replies
View Related
Oct 9, 2012
i have only usb joystick for my pc. i dont have any drivers.
View 1 Replies
View Related
Apr 4, 2011
Windows says device driver installation failed for hp laserjet 1012. This despite printer working correctly. Every time on reboot I get this message. How do I stop windows from trying to install driver for a working device???
View 2 Replies
View Related
Apr 19, 2012
My Windows 7 Ultimate upgrade($220) from Windows Vista Ultimate was 3/4 done judging from the progress bar. Received a command prompt stating that the upgrade failed due to corrupt installation files.On reboot I get a disc read error ctrl alt delete.I receive the same error everytime I ctrl alt delete. Is the disc corrupted by the upgrade?
View 4 Replies
View Related
Nov 24, 2012
A new hard drive has been installed on my laptop. I tried to install windows 7 and it failed. I am missing the master boot manager. is there free software to fix this problem that I can burn to a dvd or usb flash drive?
View 2 Replies
View Related
Sep 4, 2011
I bought my computer from best buy a couple of days ago and I recently got a message saying that my version of windows is not genuine. When I try to run the windows activation update it gives me "Update installation failed. Error information - 0x800B0001" and I still get the message that my windows is not genuine.
View 12 Replies
View Related
Sep 14, 2009
I am trying to install DirectX, but it keeps saying installation failed !
View 9 Replies
View Related
Feb 10, 2013
I just bought a new Lenovo T430s and a Samsung 840 Pro SSD. Cloned the system by using Norton Ghost (First cloned the hidden disk, then Windows 7 disk) as the manual (Samsung 830 manual) said. Then put the HDD out and put the SSD in. However, the windows failed to bootWindows failed to start. A recent hardware or software change might be the cause. To fix... Status: 0xc000000e Info: The boot selection failed because a required device is inaccessible. I checked the internet and just could understand some basic operations. For example, I entered into bios and saw SATA Controller Mode option [AHCI] Did not find any "Storage config" option... in the main menu. Also, I pressed F12 to the boot menu and selected Samsung 840 Pro but still no work.
View 2 Replies
View Related
Jan 14, 2009
I have tried installing Windows 7 in Virtual PC and on my HP 2133 netbook. Both halt when in the copy file stage with this error message:
Windows cannot copy files required for installation. The files may be corrupt or missing. Make sure all files required for installation are available, and restart the installation. Error code: 0x80070241 I have downloaded the iso's again (from the Microsoft partner site) in case there was a corrupt download, but I get the same error.
The VPC image was using the ISO directly, and I copied the files from the iso to a usb drive for the netbook install. Anyone else see this?
View 9 Replies
View Related
Jan 15, 2009
Trying to install on an Emachines laptop. I get the following error:
Specs: 1.6ghz AMD Athlon XP-M, 512mb RAM, Integrated Graphics Card.
Also, I know for a FACT that the DVD works and is perfectly fine. I've used it on other machines before.
View 9 Replies
View Related
Mar 27, 2012
I'm having trouble installing Silverlight and Office 10 Pro on my computer. I just reinstalled Win 7 on my HD and had trouble with my drivers updating, aka getting BSOD's. When I try to install these two programs, the installation windows say that the programs as failed to install.
View 5 Replies
View Related
Mar 4, 2010
My pc consist of a 200GB drive partition, one side has Win7 x86 and the other Windows Xp, Xp recently failed on me so i had to reinstall it, So i figure I'd installed Win7 X64 Since i use this Partition to run 3D and design Software, figure i could use the memory upgrade. Setup went fine, But now it boots right into win7 x64. Please tell me i can still boot into my other win7 x86 ? I never backed up some stuff on that side.
View 4 Replies
View Related
Dec 20, 2011
am failed with installation of visual studio 2008......m using window 7...
View 1 Replies
View Related
Dec 3, 2009
Motherboard: GA-MA790X-DS4
I set up the raid and everything bios related but windows 7 (64-bit) cant detect the hard drives even after i got the most recent drivers from gigabyte's website?
View 9 Replies
View Related
Mar 4, 2012
So i wanted to do a fresh W7 install on a new partition today. My setup uses two 500gb drives in raid0 with Windows 7 64bit installed. Using the windows 7 disk management tool i resized the main partition to give space to the new partition. I didn't reformat thinking i could do it before installation.So I used the microsoft tool to create a bootable usb drive. restarted, went into boot menu and set it to boot from usb first and booted into windows 7 installation from the usb drive.The computer was set up in raid0 when i got it and i did a fresh install of W7 and that time i remember it picked up the raid drivers and used those. this time however it didn't pickup any drives. I went to install and did custom install but there was no drives to choose from and after a scan it didn't find any either. i went back and booted into my main OS and used the disk management tool to format the unallocated partition. formatted as NTFS and set it to drive D. booted up from the USB drive again and there was still no drives in the list that i could install too.
View 1 Replies
View Related
Mar 1, 2011
I downloaded the VMware software to my C: drive, and when I clicked the file to open it, it opened to about 90% at which point I got the following error: Setup cannot continue. The Microsoft Runtime DLL installer failed to complete installation.I have Windows 7 and plenty of HD space. I've never had this installation problem before. It seems that Windows 7 has been a lot of trouble since I've bought this laptop; I've encountered numerous problems with software using it, though I don't know if this problem is related to it.
View 14 Replies
View Related
Sep 10, 2012
Okay, I'm trying to hook this thing up to my new Dell Inspiron 15R. The thing is, when I plug it in, it keeps failing the driver installation. Ok now here is other part. I have used this controller perfectly fine on my previous HP Mini 210. As you know, that's a pretty weak computer compared to the one I just bought.w, after about 2 hours of researching, I've downloaded the current drivers from M$, and that didn't help at all. Next I came across someone who said check the device manager. Okay, so I did a cross examination with both computers and found the netbook had something called "universal serial bus usb controller" drivers with several others branching off while my Dell did not. Also the fact that the Mini uses USB2.0 while the Dell is 3.0.So I've come to the conclusion that my Dell is lacking(and it is) these "Controller" drivers. Now the annoying part is when I use the device manager to search for updates, it says it can't find anything. I've googled around(and used the driver disk that came with my Dell) to no avail.I would greatly appreciate it if anyone could help with my problem. I'm just using the controller for gaming. It works fine in the netbook, so I don't think power to the controller is an issue. My M$ drivers are up to date so I don't think it's those either.
View 1 Replies
View Related
Jan 8, 2013
My former hard drive with my MBR on it failed. This hard drive was/is 750GB and when I purchased my 'main' 2TB hard drive I made another fresh install of Windows. In other words, I had two installations of Windows on two separate hard drives. However, the MBR is located on the now-failed 750GB hard drive, and so my 2TB install of Windows won't work. I have tried (and failed) at repairing or otherwise installing a new MBR on the 2TB hard drive.
View 10 Replies
View Related
Dec 30, 2010
I have been running Windows Vista 64 for about 3 years off of 2 HDD's in RAID0 and I just got a 60GB SSD which I wanted to install Windows 7 on it and still be able to dual boot my Vista 64 from my RAIDED drives. And then shrink the partition on my RAIDED drives to roughly 50% and create a new partition on them for my Windows 7 install to also be able to use to install programs and files. Which I was told elsewhere is totally possible. Windows 7 Install
When installing Windows 7 on my SSD I couldn't get it to install with the SATA MODE in the BIOS set to RAID, it would say "cannot install to this disc, check if its enabled in BIOS". So I had to set it to AHCI MODE, which worked, so I unplugged every drive in my system and installed Windows 7 on the SSD like this.
So the problem is when I plug my RAIDED drives back in they will only boot when the MODE in the BIOS is set to RAID but then the Windows 7 on the SSD doesn't boot as that only boots when the MODE is set to AHCI. In my BIOS the SSD is only visible in AHCI MODE, my RAID drives are visible in both MODES but as Intel_Array in RAID MODE and as 2 seperate drives in AHCI mode.
So I am in a bit of a pickle and not sure what to do... I don't mind have to change the SATA MODE settings in the BIOS to dual boot back and forth, but will I be able to shrink and re-partition the RAID drive so Windows 7 can use them? With the MODE set to AHCI I can boot to Windows 7 from the SSD, and after installing the Intel Rapid Maxtrix Storage Controller I can access most files on the RAID array so it does detect the RAID array even when its set to AHCI but will not boot the RAID array in this MODE.
I fear the problem may be with my BIOS, Motherboard or the Storage Drivers as the RAID mode should be able to support a RAID array aswell as a stand alone drives using AHCI. But for me it seems when I enable RAID MODE, AHCI fails to work on the SSD. This could be because I installed it on the AHCI MODE but thats all I could do.
My system:
Abit IP-35 motherboard
Intel Core 2 Duo E2160
4GB DDR2
2x 250GB Western Digital in RAID0 booting with VISTA 64 (for about 3 years).
1x 60GB NEW Corsair SSD with Windows 7 (64) on it.
1x 640GB Western Digital Storage drive (currently unplugged).
View 6 Replies
View Related
Jan 1, 2012
I am trying to install Microsoft Network Framework v.4 (x64) and I keep getting error "Final Result: Installation failed with error code: (0x80070643), "Fatal error during installation" (Elapsed time: 0 00:01:01)." The exact log file is attached: Code: OS Version Information:
OS Version = 6.1.7601, Platform 2, Service Pack 1
OS Description = Windows 7 - x64 Ultimate Edition Service Pack 1
OS Version Information
[code].....
View 3 Replies
View Related
Jun 19, 2012
Built a "super computer" with all the bells and whistles, did raid0 array OK installed Windows 7 ultimate on ssd 120GB drive.went to drive management found raid array, partitionnedit as 1 18TB drive without problem BUT when i tried to format it (quick since i suspect it may take days) and iwin sais failled to format drive.i will try to make a Loooong format and see what happens.
View 2 Replies
View Related
Mar 15, 2012
I've got 2 2TB hdd running in a raid0 volume setup with Intel RST. I made a flash disk for the raid drivers. Then I go ahead and start the install of Windows 7, load the raid drivers, create a 1TB partition to install Windows 7 on and have a 3TB partition for storage and such. Installs windows no problem. When i restart the system windows boot manager appears with "0xc0000225 - The boot selection failed because the device is inaccessible"If i then restart the computer, i get windows error recovery screen, if i choose Start windows normally, it boots fine. If i choose repair, it just goes back to the 0xc0000225 screen. This happens every time i restart the computer.I've tried everything i can think of, such as changing the boot order in the bios and such.
View 1 Replies
View Related
Dec 4, 2010
Looking to set up a Raid0 with 2 x 1 TB drives. Only problem is the drives are from 2 different companies. 1 is a HITACHI Deskstar 1TB 7200 RPM SATA 3.0gb/s, the other is SAMSUNG Spinpoint F3 HD103SJ 1TB 7200 RPM SATA 3.0Gb/s. Am i able still able to combine these 2 drives to make Raid0 array?
View 7 Replies
View Related
Apr 7, 2011
I have a set up with one SSD for windows 7 x64 and two Seagate Barracuda Green ST1500DL003 1.5TB HDD 3.5"
Without raid0 all is going well, when I raid0 the two Barracuda I have better performance but I have a huge unallocated space of 746.53 GB On Windows 7 disk management the I do not have any option for the unallocated space, as all options are grey out when I right click.
When I log off windows and delete the raid0, I can see all 2795 MB of the space, if I raid them again I end up with 746 GB space which I cannot add as a simple volume nor expand the other volume.
View 7 Replies
View Related
Sep 18, 2012
I must be missing a step somehow, and I'm not so tech savvy anyways, but.. I have an '08 dell xps 420, recently installed win7 ultimate x64, have 6GB ram, backed up oem internal to 2tb external, also did windows easy transfer copy to ext, now replacing oem hitachi 750mb internal w 2 1tb seagate barracuda hd's...booting from cd-rom drive works fine, but cannot seem to get raid0 config worked out nor load drivers for drives.
View 2 Replies
View Related
Dec 16, 2012
I'm showing an error in my Raid0 configuration, although windows is working properly, and from what i see, i can access all my data. But I think its time to move the install to a normal drive, and i used a ghosting tool to clone the 2 partitions to a new drive. All went fine.
I rebooted, and had to run windows repair from the original DVD, to fix the bootmgr.exe missing file. Again all went well and got all working on the new disk.
However now the clone requires 'activation' within 3 days, and when i try, it tells me i can't, because its and 'upgrade' (which it is), and that i need a new key (which i don't, at hefty price tag!!). Is there a way to fix this, without buying a new 'stand alone version' of windows 7.? (i have the original disk including the key, and its windows 7 ultimate upgrade 64bit).
View 8 Replies
View Related
Mar 18, 2012
I'm trying to create RAID0 with two drives. The first is 320GB and second 1TB. I know it won't be 1,32TB. The summary capacity should be 1229,5 GB (298.0 + 931.5). It asks for RAID name, RAID level, Strip Size and Capacity. Capacity is by default 596.2 GB and below is "The default value indicates the maximum capacity using the selected disks....". I hope the maximum size could be at least 1100GB. How is it possible to have available only a half of the smaller drive? I have:
GIGABYTE GA-Z68A-D3-B3 (BIOS version F10)
Drives Samsung (320GB) and Western Digital (1.0TB)
CPU: Intel Core i3-2100
View 3 Replies
View Related
Aug 18, 2012
i have taken off the two HHD from my 6 Tera External ( WD ),put them to my computer but they didn't work, then immediately i returned them back to the external unit, but the RAID0 was corrupted & it's didn't work, i don't care about it but the DATA inside it.I used Data Recovery program it recovered the data tree, but when i recovered the data mostly videos with their right size, but one i opened more than 10 files none of them worked.
View 9 Replies
View Related
Dec 10, 2012
I always thought that RAID 0 configuration is possible using two identical physical drives. I bought this Sony Laptop. If you go down to the Hard Drive Storage section you see you can customize it with four different options. I chose the 1st one (750GB mechanical drive). However you can see that the last two options involve RAID 0 (128x2 or 256x2). I was wondering where to install the 2nd drive as there is only a single drive compartment with a single SATA ribbon connector when you remove the back cover. I called Sony Tech Support and this is what they said: "You can only physically install a single SSD. The RAID 0 options involve a single physical SSD that inside has two chipsets in RAID 0, in other words, it's a single physical SSD that acts as two drives". Of course I never heard of this, does this exist?
View 1 Replies
View Related
