For some reason my PC doesn't seem to want to load windows 7. I've had no problems until today, the only things i have changed is that I installed Bioshock 2, after I installed it my PC stopped reading DVDs yesterday (until I reset it, then continued to work normally). For some reason when I turned it on this morning it went into startup repair and said the Event Name: StartupRepairOffline.I have tried using system restore to 3 different points (2 of them before Bioshock 2 was installed and 1 being system restore point from yesterday). After I do any of them the computer restarts then does exactly the same thing again saying that I have don't system restore at all (as the 3 restore options are still available)
My laptop keeps running Startup Repair during every startup and I can't boot my computer normally. I tried running Startup Repair multiples times but I'm still getting the same problem. Also, System Recovery did not work.What happens is Windows just starts to boot up for a few seconds, it says "Windows Starting", then the screen goes black for a second and it says "Windows is loading files..." and a loading bar fills up, then it goes black for a while and then the startup repair starts. The Startup Repair then says it cannot repair this computer automatically so I have to shutdown the computer. Problem signature:Problem Event Name: StartupRepairOfflineProblem Signature.
When I start up my computer, It shows the DELL logo. Then, it shows a grey bar that spans the screen saying "Windows is loading files..." Next a green bar that says: "Microsoft Corporation" Startup repair automatically starts. It runs for a little while and then it says:
"Startup Repair cannot repair cannot repair this computer automatically ->Send information about this problem (recommended) ->Dont Send [V] View problem details"
The problem details are:
"Problem signature: Problem Event Name: StartupRepairOffline Problem Signature 01: 6.1.7600.16385 Problem Signature 02: 6.1.7600.16385 Problem Signature 03: unknown Problem Signature 04: 21200906 Problem Signature 05: AutoFailover Problem Signature 06: 14 Problem Signature 07: CorruptFile OS Version: 6.1.7600.2.0.0.256.1 Locale ID: 1033"
If I click advanced View advanced options for system recovery and support, I get a list of things to do.System Restore and System Image Recovery have no restore points. The Windows Memory Diagnostic comes up with nothing. I do have access to the Command Prompt.
I am pretty sure that a virus cause this, right before my computer shut down on it's own my anti virus popped up and said that a Trojan was found but I didn't have to do anything. Then the computer shut down and when it restartrd started to load files and then go into startup repair, only it couldn't fix it. I tried a restore, but again it said that the startup files wern't there. I just quickly scanned the diagnostic details and noticed something that said "boot critical file C:CI.dll is corrupt".
Ever since I bought my new computer and installed Windows 7 64 bit Pro I have noticed that sometimes when I start my computer the startup locks up or crashes, requiring me to restart or it takes me to the system repair screen and running this process does nothing.
I cannot get my computer to restart. It tries to restart but keeps saying that startup repair cannot repair computer automatically. I try to do a system restore but it won't let me do that either
On start up a black and white gateway screen flashes followed by a startup Repair window.This gives me a pop up that says Startup Repair cannot repair this computer automatically.There is the option of sending the information to microsoft or viewing problem details.When looking at the details, Problem Signature:Problem Event Name:StartupRepairOfflineProblem Signature 01:6.1.7600.16385Problem Signature 02:6.1.7600.16385Problem Signature 03:unknownProblem Signature 04: 21200290Problem Signature 05:AutoFailoverProblem Signature 06:11Problem Signature 07: CorruptFileOS Version:6.1.7601.2.1.0.256.1Locale ID:1033Underneath the pop up box, The startup Repair window says WIndows cannot repair this computer automaticallywith the option of viewing diagmostic repair details or viewing advanced options for system recovery and support Under the advanced options, I have tried the startup repair, the system restore, the command promptchkdsk/f/rNone of which have worked Prior to this the notebook was working fine last night, I did not install anythingI ran the Farbar Recovery Scan ToolMod Edit: Removed FRST data, this is a malware tool not permitted in this forum and you have made no indication that this is a malware situation ~ Hamluis.
Start up repair cannot repair this computer automatically , I am getting this all of the time now when starting the PC ,i am sure it started when a new video card got put in but not sure?
I have no idea what was the last thing done on this computer (it is my wifes), but I do know that every now and then there has been a disc failure, checking disc startup, but it has always had a positive outcome.[CODE]
i use ubuntu OS and windows7 professional on an HP dv5 notebook, last week i made a mistake in that i removed the battery while the machine was on as i was using windows7. the time i tried to restart it again it recommended startup repair which ran but 'could not repair it automatically' i tried the f8 options but to no avail. when i run scan and memory diagnostics all are successful but the system can still boot. am able to view my data on windows through ubuntu but ubuntu can't execute windows programs. what should i do to restore windows without loosing data?
I have a Dell Inspiron and a while ago I shut down my PC and the next morning I was faced with options to repair my computer. It hung on the screen for ages before it actually came up with startup repair and supposedly fixed the problem. A few days later, everything got very slow and started to freeze a lot and before long, booting the computer got very slow as well as it hung for about ten minutes on a black screen after the 'welcome' screen before finally starting up. I decided to reinstall the operating system (I did NOT reformat the C drive), so I borrowed my Grandma's external hard drive and copied my files. After reinstalling using a Dell Windows 7 64-bit Home Premium Re-Installation DVD, I copied and deleted the files off the external hard drive onto my PC (I didn't know it would create a Windows.old folder) and started installing programs. Then I left it overnight to install quite a big program. This morning, somehow it had turned off. I turned it on and it gave me the safe mode options and a 'start windows normally' option. I chose the latter and after typing my password it hung on the welcome screen again. I left it for ages and it just went back to the user login screen again. I pressed the red button in the corner to shut it down but it just hung once again on an empty screen so I did a hard shutdown (held down the power button). I turned it on again...startup repair. It gave me the option for system restore, which I did (then realising when it finished that I hadn't made a backup). I booted it, and again it wouldn't start properly. At this time, safe mode booted fine. After trying various things (even using a compressed air can to get rid of dust) and a few hard shutdowns, suddenly every option from the advanced boot menu took me to startup repair except 'Repair your Computer' which gave the normal options for repair (although now it only gives me 2, Startup Repair and DataSafe Restore and Emergency Backup. Now when I do startup repair, some times it says it has fixed the problem, and sometimes it says it cannot be fixed automatically and gives me information on the problem (a few things it said were: 'StartupRepairOffline', 'AutoFailover' and 'CorruptRegistry').
I can't reinstall my computer because then I would lose my precious files.
Is there some way I can save my files and reinstall or even just save my files somehow or am I screwed?
the Startup screen. So I went to the Startup repair tool as was recommended, but after few tries nothing has changed. So I tried to recover to previous recovery point, but also nothing. Then I tried booting to Safe mode, and I saw that during the loading process there was no file shown as succesfully loaded. I might also know what could be the cause of this problem, because yesterday when I was shutting Win down, there was a blackout so obviusly some files are corrupted.
I hate it when this happens and so far, the startup repair has always been able to fix the problem. Today, I'm not so lucky. I'm using my other built right now coz I have to work. I don't remember what updates I did last night but I do remember the dvd drive firmware was updated.I popped in the system restore disc, start it up and the same page appears: Start with windows start up or Start windows normally. Tried both and neither one of them would bring up system restore. This built was only a month old and was hardly used so far so no system restore point was created at this point. I have files in it that I would like to keep but I can't get to them right now so a clean fresh install is needed but I can't get it up.
I have a Toshiba Satellite C655-S5132 that just shut down & now will not boot Windows 7. Just goes to black screen w/blinking cursor then goes to 'startup repair' (which I'm postiive this is a virus of somekind) & will not allow me to do anything. Just repeats itself. I downloaded Windows 7 repair to a CD-R, chgd BIOS settings to CD/DVD to boot first, saved changes, and will NOT pull/boot up from disc. I've tried 2diff repair discs, both do not work. 'F8' does not do anything for me, not able to get to 'safe mode'. Computer is only 2yrs old.
I have a Toshiba Satalite p205 which came with Vista pre-installed. I installed full version of Win Ultimate and everything was fine for awhile. Later on after numerous updates it started to want to do a startup repair 3 out of 5 times. My last resort was formatting and re-install.
I really need some help with something and I'm at wit's end with this thing. My Windows 7 Dell laptop refuses to boot up past startup repair. When startup repair finishes, it says it can't fix the problem automatically. Upon reading the logs of startup repair, it says file d: ci.dll is corrupt
It started automatically in the middle of the night and nearly 24 hrs later it's still going. I tried to stop it and a window pops up saying it can't be stopped. Every 5 min or so the computer restarts and the Startup Repair continues. I've tried to stop it during the startup with alt F2 but I don't get any choices such as Safe Start, only Start Windows Normally.
I was on my computer when out of nowhere it shutdown and restarted with the satrt up repair. It says it can not fix the computer automatically and says this in the details window
problem event name: startup repair offline problem signature01: 6.1.7600.16385 problem signature02: 6.1.7600.16385
[Code].....
I tried to run a scan in the command promt window but it said that another repair was running and the computer needs to be restated which i did and the whole thing just starts over again. I dont want to lose any of my pics so i dont want to have to reinstall anything
Whilst looking for a keygen for Microsoft Office 2010, I must have got a bad file.. yay. When I clicked on the app, my computer immediately went to the Startup Repair window and has been relentless. I've tried opening in SafeMode thru F8 for a system restore, no good. And attempted to start windows normally through F12.
Finally, the Startup mode is over and I'm attempting to turn it back on ... and we're right back into Startup Repair.
I have a Sony Vaio laptop which is only a few months old. Here is the problem: i was trying to uninstall the trial version of office 2010 (after failing to activate it properly) and after going into control panel and clicking on "uninstall" to remove the office 2010 software, the computer automatically shut down and restarted and went into startup repair. after running this a couple of times, it said it was unable to fix the problems and asked to send the report to microsoft. then it just shut off by itself. i turned it back on and chose to "start windows normally." even then it went into startup repair and was again unable to fix the problems. then it just became stuck with a blank screen so i had to force power off. now i am not sure what to do. i don't want to keep restarting it only to go into startup repair and burn something out by turning it on and off so frequently.
Windows 7 (32 bit) will not start.All I see is the 0X0000007b message."Starup repair" is no good either. When you run startup repair it goes in cirkles: It begins the start up, but you get 0x000007b. Computer rebootes. You can choose "startup Repair" og "start windows normally".You then choose "startup repair". It begins the start up, but you get 0x000007b. Computer rebootes. Etc., etc.. And you can not start windows normally either. It all began when Norton found something that needed to be taken care off. What can be done to fix the boot?Shal I use the "Farbar recovery Scan tool"?I'm not quite sure how it works... Are there other things that can be done?Anything that demands you to use windows one way or another is not possible for the time being as you see.
I left the computer on for the evening and returned to it this morning only to find the Startup Repair Tool. I have attempt a number of different reboot attempts to no avail. Using F8 during start-up is not being recognized so I cannot boot up in Safe ModeHere is the Startup Up Repair Tools Readout:[CODE]
My boys PC is running windows & and is stuck at Startup Repair, it runs, then comes up with "Sratup repair cannot repair this computor automatically" He did have that wonderful AV suite virus on there which i managed to get rid of, then this happened. A few people have said do a fresh install of W7 but he has loads of pics and music on there that i dont want to lose. Can i do an reinstall without losing data? ah, but, plum of the day award could go to me as the problem could be hidden in one of those files??OR do i take his HDD out and back up only the necessary files he wants to keep, then put it back and do a custom install from there?
I was surfing the net today when my laptop suddenly reboots and i was required to launch Startup Repair. However, after the loading files bar, it does nothing but shows the blue bg with the cursor - there's no indication (like 'Attempting Repair' or etc) that it is doing anything in the background. It is supposed to be like this?Ive tried restarting the laptop in safe mode but it auto reboots to the screen where i only have two options of either launching the Startup Repair or launch normally (which i can't). Ive pressed F8, tried launching launching repair but it still ends up to the blue bg screen, doing nothing.I haven't installed any new software or Hardware though i hvae been leaving my laptop on for days on end to download stuff
I am using an older Microsoft Bluetooth keyboard and mouse on my Windows 7 HTPC. This usually works wonderfully, except when the new startup repair screens are shown. These screens REQUIRE you to click a button (or press Enter) to continue, and will sit there for all etenerty until you do.
The problem is, they are shown before the drivers for the bluetooth keyboard and mouse are loaded, so I can not click them with out stealing a wired keyboard or mouse from my other pc. This seems like a pretty stupid choice to me, as every other such option has some kind of time-limit on it so that it will automatically continue.
Is there a way to either have the startup repair screens default to some option after a short time, or to completely disable them?
My baby likes to press the pretty blue power button on the machine, and therefore I see that screen often, and am getting tired of running for the keyboard every other time I want to sit and watch a DVD.
I was using my computer to update my ipod and it suddenly restarted. I figured it was restarting because of the ipod and I left it. When it turned back on, it was doing a startup repair, which I've never seen before and didn't ask it to do. When it finished, it said that it couldn't fix the errors. It restarted my computer and opened the startup repair again. I've tried the system restore too and it still opens to the startup repair everytime I turn it on. I don't know what to do and why it's doing this but I'm getting nervous about it. How can I fix it, or at least get past the startup repair so I can back up everything and restore the computer to the factory settings?
I've read other posts about start up repair and tried what the others are told to fox their problem but nothing works for me. When I turn my computer on I can choose start up repair or start normally. Both options go to the start up repair. I have left it on for hours and nothing happens. I've tried pressing f8 and other buttons but nothing comes up. What now?
