Raid Boot Error After Bios Update

Feb 6, 2010

After flashing the bios, my computer could not find the OS. The options displayed recommended that I try to repair the OS, so I made that selection with no joy. I went into the bios setup and found that it was no longer setup for my raid 1 drives, so reconfigured. When I did this, I missed setting the SATA 4/5 to IDE and went through the process again of trying to repair the OS. Once again, that did not work.

I went back into the bios and discovered my oversight, fixed it, but the computer still does not recognize my raid drives. The raid bios setup utility still shows a valid array. At this point, my assumption is that it doesn't recognize the array drive because the driver isn't loading, so I've tried to reload the drivers. The motherboard manual only describes how to do this when installing a new operating system and I do not want to lose my programs. Do you have any suggestions?

View 1 Replies


ADVERTISEMENT

RAID 1 Not Recognized In OS After BIOS Update

Feb 1, 2013

First off I am running Win 7 on a primary SSD, and have 2 1TB HDD in RAID 1 for storage. I have been running this setup fine for a while now. I recently updated my BIOS (P8P67) using the EZ Flash utility from USB per the following steps:

-Restore defaults
-Flash new BIOS
-Restore defaults
-Reset SATA mode to RAID

Everything went fine, and I verified that my BIOS was seeing the 2 HDD as 1 volume. The Intel RAID controller shows the mirrored volume and 2 drives on bootup, all fine. However, when I get into windows, the RAID volume is not listed in the Intel RST software, device manager or disk management.

View 1 Replies View Related

BIOS Update RAID Windows Reinstall?

Feb 10, 2012

Before I begin my overclocking project, I'd like to update my BIOS. I'm currently using an ASUS P8Z68-V/GEN3 with a BIOS of 0301. According to their website there is a new BIOS 0402. One of the two components of the update states "increased stability". So I'm thinking updating the BIOS would be groovy before I begin my overclocking project.After my week old build, I've done two things to the 0301 BIOS. I've used the ASUS OC for dummies button and overclocked it to "Fast" (not Extreme). I've also configured it to RAID.

1) Should I "un-overclock" to its original settings it before updating?

2) When I update it, will the update put the BIOS back to default settings, including the RAID setting reverting to AHCI?

If the answer to #2 is yes, then it will default to AHCI rather than RAID when the update is complete.....so is it just a matter of resetting it to RAID before attempting to boot Windows again? I ask this because of the pain I experienced when I had to reinstall Windows after going from AHCI to RAID the first time.

View 5 Replies View Related

[BIOS] Really Bad , Wont Boot After Bios Update?

Aug 25, 2012

so i did a bios update, and it wont boot after the update.its a asus m4a79xtd evo (rev 1.01g)i dont have a backup of the bios

View 3 Replies View Related

Bios Change From Raid To Non Raid On Dell Xps435

Jan 1, 2013

I had one hard drive failed(640gb). I bought replacement and tried to restore image but it failed. Then I wanted to convert to non raid system. I changed both drives(640gb) to non raid and bios change in advance setup. I am getting error when I try to reinstall win 7, "setup was unable to create a new system partition or locate an existing system partition. See the setup log files for more information". I have deleted old partition many times but win 7 setup on this dell xps435 desktop won't install windows.

View 4 Replies View Related

Windows 7 Won't Boot After BIOS Update?

Oct 25, 2012

I updated the Bios from toshiba site after that my windows won't start and I can't even get to Bios setup (F2) or Boot sequence (F12). and windows get stuck as soon it starts. I can't even access to Factory Restore. I have no image. For information I am using Toshiba Qosmio X770-107

View 11 Replies View Related

BIOS Update BSOD No Display On Boot

Oct 19, 2012

Earlier I was trying to fix a DCP latency issue and latencymon suggested I update my BIOS. I got the BIOS from Asrock directly. During the update I was given a BSoD and memory dump. The dump froze at 15 and I eventually turned off the computer. Upon rebooting I was unable to get a display.

So far I have reset the cmos, switched between gpu and integrated graphics, removed the gpu and other adaptors, let the computer stay off for 30min; all of which has not worked. When resting the cmos I used both the jumper switch, quick clear, and battery removal.

Dr. Debug shows no errors when starting the computer and it appears to continue cycling boots, despite the lack of error.

O.S - Windows 7 home premium x64
CPU - i5 3750k 4.2gz
Motherboard - Asrock Z77 Extreme 4
Gpu - MSI 550ti
SSD - Corsair Neutron Gtx 128gb
Ram - 2x 4gb 1600 9-9-9-24 patriots.

View 4 Replies View Related

Boot Manager Missing After BIOS Update?

Apr 28, 2011

I updated my BIOS as I was having a problem mentioned in one of the updates. I was using the Easyflash2 by Asus and the update succeeded but when it re-booted I got the awful news..boot mgr missing. Would my best bet be to just re-image?

View 7 Replies View Related

Windows 7 Ultimate Won't Boot After Bios Update

Oct 28, 2012

I have a desktop using a Gigabyte GA-Z68X-UD3H-B3 (revision 1) motherboard. Using the Gigabyte @Bios utility, I updated the Bios to F12. After rebooting as @Bios suggested, I can no longer get Windows to boot. I've noted the following:

1) I have issue accesing the Bios setup. Sometimes I can access it, sometimes I cannot;

2) When I am able to access the Bios, I can confirm the disk Boot Priority, however it's is now showing the drives as SCSI (I only have SATA drives);

3) There is a new setup screen displayed after the Gigabyte logo screen shows. This screen now shows 'Serial ATA AHCI, Version iSrc 1.20E.

Copyright (c) 2003-2008. Intel Corporation.
**This version supports only Hard Disk and CDROM drives. **
Please wait. This will take a few seconds.

Then shows Controller/Bus/Function/Port/Device and lists all harddrives. At the end of the drive list it shows 'AHCI Bios installed'

4. After step 3, it shows the prompt 'Loading Operating System' - the boot hangs at this point.I DID backup the existing Bios before updating it. I have not gone in and copied that file to a floppy to try and flash the Bios using the backup (don't know if this is possible).

View 3 Replies View Related

Samsung Bios Software Update For Bios / Update Fails

Dec 1, 2012

My Samsung series 3 laptop has been sending out popup messages telling me I need a bios update, I go to the Samsung software update site and this bios update has been failing, I have made several calls and chats to techs at Samsung who tell me to do what I have already done, they tell to ask for tier 2 tech, who can go in my computer and fix it , When I finally got a tier 2 tech, they told me the same thing, I told him what I had been told about him and what he could do, He said, is it working , I said yes, but settings on computer change on their own,like wifi turns itself on and that concerns me. Anyway, He said that it didn't need a bios update,even the Samsung website said this computer needed a bios update. I posted this on hardware,firmware concerns, and they told me to post here, I was going to go to a site ,that had a download that checked drivers,

View 3 Replies View Related

Failed BIOS Update, HP PavilionG6 Won't Boot Up And Only Black Screen

Jun 2, 2012

I have an HP Pavilion G6-1d40ca. It crashed the other day while I was using it, and when I restarted it, it went to BIOS update. It froze while updating, and died in itself (I think the battery died, it wasn't plugged in. I never knew about BIOS update, so I wasn't expecting for the battery to die during the update, so I didn't plug it in.) Second time, booted it up (it was plugged in this time), and went into BIOS update once again. All's good, was able to use the laptop for about five minutes, then it crashed once again. Now, when I boot it up, nothing comes up on the screen. No nothing. The power button is on, the wi-fi is on, the LED light is blinking non-stop, more than 6 times than what is referred to the HP website.

I tried doing the remove battery and adapter, press power button for 30 seconds, plug it in without the battery, but to no avail. I also did the whole win+B, but doesn't work either. I tried pressing f11, but nothing comes up on the screen. I don't remember where I put the recovery discs that came with the laptop. I thought I put it on the box together with recovery discs for our other computers at home, but I guess I didn't. The thing is, I don't know where to begin, since I don't have anything on the screen itself. Not even a start-up logo or something.

View 4 Replies View Related

Flashing BIOS Firmware Update Has Lost Windows 7 Boot Record?

Nov 30, 2012

I wanted to install more RAM, but Supermicro support told me I needed to update BIOS (flash it) to enable it to accept higher RAM.After I did this, the BIOS seems to have lost the record that boots my Windows 7 installation. After going through the checks, it just comes up with "Operating System not found."So I thought that, since I have two SATA drives, I could try installing Windows on my redundant disk to see if that might generate a dual boot menu.I was able to successfully install a fresh copy of Windows on the 2nd disk, but it will only boot into that one. It seems my system has completely forgotten about my other, working, installation.Is there a process for recovering the boot information and setting it up such that I can go back to using my other installation?

View 2 Replies View Related

Error 1234F: Would Not Boot Or Load BIOS

Dec 30, 2011

This morning I powered up my PC and got this error, 1234F:

Tried pressing 1 and nothing happened. Restarted and tried to get into the BIOS by pressing DEL, but the BIOS wouldn't load. Opened up the computer and unplugged all my hard drives and unneeded USB devices. Got into the BIOS fine after that. Powered down and reconnected the boot drive and everything booted up fine. Ran a quick test on the hard rive using the Seagate Seatools utility and it passed. Reconnected the other drives and again, everything checked out fine. I hope to run longer tests on my drives later this morning just to make sure.

I did have a Ubuntu live usb stick plugged in, but I have this plugged in often and have never had a problem. Tried recreating the problem by reconnecting everything and restarting but everything booted up fine.

The only things I have done to the PC is swap out two internal hard drives two days ago. I also have been having problems with my USB ports which I haven't figured out yet, this will probably be the subject of another thread!

So everything seems to be running fine now but I am a little worried about what might have caused my problem and if it is an indication of another problem? Is there anything I need to check?

Windows 7 SP1
Intel Core i7 930
12gb Ram
Asus p6t deluxe v2 motherboard
Nvidia GTX-260
XFX 650w PSU

View 2 Replies View Related

BIOS Boot Loop, Error When Try To Re-install

Feb 21, 2012

I have a laptop with Windows 7 x64, I re-partitioned my drive in Disk Management (shrink) and now my system won't boot.

Here is what happens:

1. Acer Splash Screen
2. Small blinking cursor.
3. Rinse, repeat (Acer screen again!)

When I try to boot from Windows 7 DVD, I get CDBOOT: Could not find BOOTMGR.

View 1 Replies View Related

BIOS Disk Error - Resetting Boot Priority To Correct Drive?

Jan 27, 2012

When there is a Restart required after a software upgrade, the BIOS on my system (Win 7/64) will go to an external HDD (I have three for storage and backup). If I force it off and go into the BIOS on startup, it will show any of the other three HDD's in the boot priority. I reset the priority to the correct drive, save and start (repeat this process several times) and finally it will start from the correct HDD. I thought it might be the CMOS battery but with a new battery in place I still ran into this. This system (HP desktop) is less than a year old.

View 2 Replies View Related

RAID Array Setup - How To Get Into BIOS And Change Settings

Jun 21, 2012

I am getting ready to set up a RAID Array but this is my first time doing anything with RAID. I know how to get into the BIOS and change settings and I know with two hard drives, I should do RAID 1. However, I just have a few questions before I do this. First off, I am an idiot and did not notice that my first hard drive I got when I built the computer has a 32 MB Cache:

Caviar Blue 1TB 7,200 RPM SATA 6.0Gb/s 3.5" Internal Hard Drive WD10EALX - OEM

I noticed it only had a 32 MB CACHE when I went to get another one. I then asked for the version with a 64 MB CACHE (WD1002FAEX), paid for it and left. Will these two hard drives work together in RAID if they have different sized caches?

View 3 Replies View Related

Missing Operating System - RAID Drive - Show Up In BIOS

Nov 14, 2011

I'm working on a computer with a RAID setup. It is 2 hard drives 500gb each showing up as 1tb in windows. Both drives show up in the bios but all of a sudden when trying ot start the computer I get a "Operating system is missing" error.

I'm trying to run a chkdsk form a win 7 64 bit disk and telling it to run on H; (system drive) but it says 'cannot open volume for direct access'.

The other drive, C: is just a recovery drive built into dell computer systems. I tried using a boot cd and running mbrfix to no avail.

View 3 Replies View Related

SB600 ATI RAID AHCI Drivers? (BSOD On Boot If In RAID/AHCI Mode.)

Jan 6, 2009

anyways, my main drive is a RAID 0 with Vista x64, but I have a second HD that is a SATA 250GB, which I installed Windows 7 on. The only way I could get install to work was to switch my BIOS to IDE mode rather than RAID. I would of course though, like to be able to access my Vista drive from Windows 7 (and more importantly, not have to switch between IDE/RAID mode at all in the BIOS, it's a pain).

Now, the one odd this about this all is that the drivers I have for Vista (x86/x64 drivers) for this mobo's RAID controller WORK when loaded on installation to identify and install to the drive, but seem to not load or not work in any way once the first reboot on install occurs. Maybe this is because I installed from within Vista x64, though.

(Incedentally, my motherboard is an M3A Asus, using ATI's SB600 for a RAID controller)

I've tried loading the drivers from within Windows 7 while in IDE mode, but the install program won't let me. At first it didn't allow because of version restrictions, but then I altered the ini file to get around that, but it encounters some sort of error when installing and quits.

Any help that can be offered, would be grateful. I realise it's a beta and not a real release, so I can get past the BSOD from my odd setup, and I really am enjoying playing around with it so far. Very very impressed.

Edit: Just in case anyone thinks of suggesting me to right-click the inf file and install that way, already tried, won't allow for it.

View 0 Replies View Related

Windows Didn't Boot Up After Update.error 0xc0000225

Apr 24, 2012

windows didnt boot up after update. error 0xc0000225 info: The boot selection failed because a required device is inaccessible.

View 1 Replies View Related

Switching BIOS SATA RAID/AHCI Setting Causes BSOD At Windows Start

Mar 30, 2012

I just changed my disk setup from:

1 SATA HDD Primary OS Disk
2x SATA HDD Backup Disks in RAID 1

TO:

1 SATA SSD Primary OS Disk
1 SATA HDD Backup Disk
[No RAID]

Everything worked great, no problem. So, since I don't have a RAID array anymore, I decided that I could change my BIOS setting to AHCI instead of RAID. I have a Gigabyte GA-P35-DS3R v1.0 mobo.


These are my steps:Settings > Integrated Peripherals > "SATA RAID/AHCI Mode" = RAID
--> Changed this setting to AHCI Reboot Windows Start screen shows up, but as the color orbs are spinning into focus, BSOD and immediate restart Repeated reboot several times, same outcome
Next Step:Launch BIOS settings Integrated Peripherals > "Onboard SATA/IDE Ctrl Mode" = RAID
--> Changed this setting to AHCI Reboot Windows Start screen shows up, but as the color orbs are spinning into focus, BSOD and immediate restart Repeated reboot several times, same outcome
Switch both settings back to RAID, reboot, and Windows starts up just fine, no issues.

What am I missing? Why can't I set it to AHCI mode without BSODs?

View 8 Replies View Related

HP BIOS Update Stuck At "Verifying New Bios Image 100%"

Jan 19, 2011

I have a five-month old HP Compaq Presario Laptop, which has been working fairly decently (I've had a few virus scares, and my Norton quarrentined something a twenty days ago). On HP's advice, I just updated the BIOS on my laptop. It's currently stuck at Verifying New Bios Image, and it's at 100% - It's been stuck that way for a half-hour plus.

View 14 Replies View Related

Created Boot Partition Manually / Service Pack Update Error 0x800F0A12

Jul 28, 2012

I reinstalled Windows recently, but it used the same boot partition from my old installation. I got rid of the old partition (it was on the wrong hard drive) and created a new one with the repair disc. Windows boots, but won't install updates. Bcdedit outputs The boot configuration data store could not be opened. The system cannot find the file specified.

View 6 Replies View Related

How To Update BIOS

May 11, 2012

As I mentioned how can I update my BIOS version I download the latest BIOS files from the manufacturing site but cant be able to update it.I have HP Compaq dc5850 Small Form Factor PC and My Current version of BIOS is 2.1 and update is 3.3

View 9 Replies View Related

BIOS Update Fail?

Apr 8, 2011

Everytime I try to update my BIOS on my laptop I get this error: BIOS update failed!New Bios is not compatible with the current system BIOS. New BIOS part number doesn't match system BIOS part number. Error Code: -120See the for troubleshooting

View 5 Replies View Related

Bios Update Now No Desktop

Jul 16, 2011

So I updated my bios today from 1.7 to 1.A. When the system restarted it goes to Windows 7 with a black screen that says "C: windows system 32configsystemprofiledesktop Refers to a location that is unavailable". From here I have all of the basic buttons but I cannot access anything. I get an error even trying to run regedit. My system ran fine before the bios update. The system setup is as follows: 50GB SSD with Windows 7 installed only..4x 500GB HDD in Raid0 with all user profiles and default save locations set to it.
2x External drives (not to important here just run Ubuntu and a spare drive)When I set the system up I changed all of the registry settings so that windows automatically saved everything to the Raid0 drive. Everything is still on the drive as it has been unchanged but Windows fails to find the desktop settings now.When I looked in the system profile folder there was no "desktop" folder there. I manually created one and got some of my shortcuts on the desktop back but everything is still missing. At system launch I edited all registry settings to point to drive D: as the primary. Maybe something changed there?

View 5 Replies View Related

How To Update Both Bios And Windows 7

Jul 8, 2010

i wanted to know i can update my win 7 and also my bios

View 7 Replies View Related

Emulate A BIOS Update?

Oct 1, 2012

I have an .ROM file I would like to "try before I buy" so to speak. Is there anyway to safely emulate a BIOS update?

View 9 Replies View Related

BIOS Update For P5Q Motherboard?

Apr 14, 2011

I'm trying to find an update for the P5Q motherboard and I'm having a hard time trying.

View 1 Replies View Related

How To Update The Dell Bios

Jun 17, 2011

I have a 435mt mobo in a custom rig. Anyway, my problem is that I need to update the bios. I download the executable to "flash" update my bios from Dell.com but it crashes.

View 7 Replies View Related

How To Update Gigabyte Bios

Oct 8, 2012

How to update gigabyte bios

View 2 Replies View Related

Toshiba Sent Out A Bios Update

Dec 25, 2012

Toshiba sent out a bios update. upon download and install I started getting conflicts. I discovered that this manufacturer update installed 32 bit bios into a 64 bit. Where can I get a download to correct this bio fail?

View 1 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved