Netgear DG834v3 Router Fails To Connect To Internet
Sep 11, 2012
Not my week so far yet another problem. Been trying all day to connect to the internet with the above router.Happened accross a screen saying Firewall settings.It says for the inbound services "BLOCK always" is this my problem?I have tried to amend this to " ALLOW always" to which the outbound services are already set.My next problem is it is asking for the inbound services to be adjusted so I have setthe service parameter to ALL, action ALLOW always but now is the problem it wants an address putting into the 4 boxes for the Send to LAN Server parameter,I have tried various setting but to no avail. Exactly where can I get this information from?
I have a netgear wireless router upstairs. My dell laptop, my iMac (which is downstairs) and my iPad/iPhones all connect anywhere in the house. My Toshiba laptop and my work dell will not connect or it connects very intermittently. I can stay connected for days on other wifi networks, just not at home. Any ideas?
I have an Asus laptop with Windows 7 and a netgear N600 router and I can't connect to it or any Netgear networks. I can connect to other networks and others can connect to my network and all other devices work except my laptop.
But I cannot get my NEW Netgear N600 router to communicate with a NEW Netgear WN 3000 RP extender.The instructions say to press the WPS button on the extender then the WPS button on the router. No WPS button exists on the router!The instructions also I can use any wireless network manager utility to set this up. Can't find where this is in Windows 7.The I pad has found the NETGEAR_EXT address but won't connect. And the light on the extender does no indicate teh router is communicating with it.
I have tried connecting to my router with both wireless and lan cable but they both fail. What is strange is that my vista laptop (currently using) has no problems connecting either wirelessly or using the same lan cable as my desktop failed with. My windows 7 desktop was working fine earlier today but after I went out it installed the updates and since then no amount of rebooting or restarting of the router has fixed the problem.
Just did a clean windows 7 x64 installation on a build a box computer with a new hard drive. Install went fine. Plugged it in to my 3 month old Linksys Wireless G Broadband Router (WRT54GL) and it doesn't recognize that there is any connection at all. Windows says "No connections are available" and troubleshooting can't identify the problem. The light on the router and on the computer comes on. I am running a wired connected XP computer and 2 Win 7 x32 wireless connected computers just fine. Ran ipconfig /all and it came up as follows:
Host Name.................... : Bottomdweller-PC Primary DNS suffix.......... : Node Type ....................: Hybrid
[Code]....
All wires are connected. I've tried booting in Safe mode with networking. I've even connected the computer directly to the cablevision modem. I've installed a USB Linksys wireless adapter and although it installs fine, it doesn't see the router at all. I've also tried reinstalling the router directly on this computer but it doesn't see the router at all.
I've tried setting up a new connection or network, Connecting to a network and choosing a homegroup and sharing option but since you need a network to connect to first I couldn't do it.
I am running windows 7, 64 bit and have been having an issue with my Linksys E1500 router recently that has my ISP
My router will respond to pings from my laptop both wirelessly and when connected via ethernet cable, and will respond to pings from my ISP, but it won't allow my laptop to connect to the internet. I have rest and reconfigured the router a bunch of times, leaving the MAC address alone, cloning it to my laptop's ethernet port, and cloning it to my wireless cards MAC addresses, respectively. None of that allows it to connect. Linksys (Cisco) has been useless in helping both via their site and when contacted, encouraging me to pay $40 to talk to someone who MAY be able to help.
Note: The router worked fine for about 4 months, then one morning, couldn't connect to the internet through it. Have to connect directly from the modem via ethernet cable.
I just installed the Windows 7 upgrade. My printer would not print so I called Dell. I was on the phone with them for 3 hours trying to get it to print. They eventually told me that my wireless router, (Netgear WNR2000) had a wrong IP address of 168. something. They told me I had to change it to a 192. number. They further told me to change to WEP. I went to the wireless site and typed in 192.168.1.1 and logged in. I changed it to WEP but then the internet would not work. I do not know what to do. Can someone please help me?
I am trying to set up WPA security on my new Dell Inspiron Laptop,When I go to "Help and Support" for instructions it says:"The Set Up a Network wizard will guide you through setting up a security key.Click to open Set Up a Network."My problem is when I "Click to open Set up a Network" it only shows my neighbor's router [A Linksys WRT110]. My Netgear WGR614v6 does not show up as an option to connect to.
My Netgear Wireless-G WGR61v10 router has suddenly stopped doing its thing. No changes were made to it, and it's not that old - maybe a year and a half. Short enough to not think its gone bad and long enough to stop getting free Netgear support.I rebooted everything after pulling the power, first from the cable modem, then the router, then the computer, but no change. Neither my laptop or desktop will get online through the router, even when directly connected. I can ping the router, however.
I have a Netgear DGNB2100 Wireless N router. It is connected to an old PC via Ethernet cable. That connection works.
While downloading a 64 bit driver to use for the USB adapter for my PC, I connected my laptop to the wireless network with the laptops WiFi card (Intel PRO/Wireless 3945ABG), and used the internet for about ten minutes.
I then configured the USB adapter for my PC, after disconnecting the laptop.
My laptop will detect the network, but when I put in the password, I get a message saying Network Security Key Mismatch, and am prompted to type the key in again.
I have also tried pressing the WPS button on the router instead of typing in the password with no luck.
The laptop is an Acer Aspire 5920, with the aforementioned Intel PRO/Wireless 3945ABG network card, and it is running Windows 7 Professional 32 bit.
I am using a netgear DG834GT router however having just bought a computer running on windows 7 I am having real connectivity problems, other laptops in the household are on XP and have no problem, is there an answer out there?
For some reason my router and modem will not show correctly on my dell inspirion one desktop. Im running windows 7 and here are the net work connection deatils
Connection -specific DNS Belkin Description Realtek PCIe GBE Family Controller Physical Address 00-00-00-00-00-00 DCHP Enabled Yes Ipv4 Address 192.168.2.2 Ipv4 Subnet Mask 255.255.255.0 Lease obtained Wednesday, November 10, 2010 9:45 PM Lease Expires Sunday, December 18, 2146 4:17 AM IPv4 Default Gateway 192.168.2.1 Ipv4 DHCP Server 192.168.2.1 Ipv4 DNS Server 192.168.2.1 IPv4 WINS Server NetBIOS over Tcpip enabled Yes
The Connection was working about ten days ago and then suddenly stopped and read as an unidentified network no internet access. at one point is was not receiving packets but now it is but it still says no internet access on the IPv4 Connectivity. Media state is also enabled and the speed is 100.0 Mbps when i troubleshoot it says windows cant identify problem but in the details it says default gateway is available. when i use the cmd prompt ipconfig/all my local ethernet adapter has a physical address of all zeros.
I am trying to configure a Netgear WNR3500 router to be used as an access point.My AT&T U-Verse Gateway router is in the basement of my house and the WNR3500 is in my office on the second floor of my house. I am using the Netgear Knowledge Base article ID 19852 titled "Set Up a Wireless Router as an Access Point on a Network".In Step 5 is says in Advanced tab Setup > LAN "In the IP Address field, change the LAN IP address of the router (WNR3500) to 192.168.1.100 (same IP segment of the main (AT&T) router (192.168.1.1) and uncheck the DHCP server box.I did that and the wireless access point doesn't work.The AT&T Gateway wireless router IP address is 192.168.1.254. I also tried changing the WNR3500 LAN IP address to 192.168.1.200 and the access point still doesn't work.
i have a samsung laptop running windows 7. i have a netgear modem and router. all of my other devices connect with no problems but my laptop wont stay connected. it will connect for a while and then it will disconnect.
I have Windows 7 64 bit. I bought a Netgear DGN2000 approximately two years ago. It is working well. Currently, there is good connectivity between my laptop and the modem/router (wired and wireless).
I worked on my desktop this morning, uninstalled some programmes, but must have uninstalled a driver or something. I inserted the Resource CD, which installs the modem (although it is installed). Then it stalls at some point. If I troubleshoot, it states Windows do not detect a properly installed network adaptor.
I just bought a Netgear WNA3100 wireless usb adapter for my HP Win 7 64 bit laptop. I have been trying for 2 and half days to figure out why my speed is slow, why i don't have a good signal, and/ or if I do have a bit of a signal to my luck, why my signal comes and goes. I don't have internet at home at the moment because I am trying to save up to go to school. I am picking up a public business signal from a block away (which I have asked for permission to use), but I only am receiving not much of a signal with the Netgear usb wireless adapter.
Last Friday my main desktop crashed (lost power to the machine) and on restarting the PC was unable to "identify" the network. By identify, I mean, when using "Network and Sharing Centre" on the basic network information page, the PC shows "Identifying" under "active networks" - no matter how long I leave the PC.
PC details Model: Packard Bell Power x-30 Processor i7 870 @2.93GHz RAM: 8GB O/S: Windows 7 Home Premium (64-bit)
The main desktop is connected to the modem router (via Ethernet). The modem router is showing no sign of any problems itself, all the dashboard lights look ok (i.e. power is on, port 1 shows the Ethernet connection in place, both wireless bands are lit, the DSL is lit and so is the internet). The household contains a number of laptops which continue to work ok wirelessly and/or wired through Ethernet. Even mobile phones are accessing the wi-fi ok.
The DNS Server address looks ok, as that is the address of the web page to the router. I cannot access that web page (address) via the main desktop, but I can from other devices ok. Having gone through Device Manager the Realtek PCIe GBE Family Controller is showing as "working properly". I have tried pinging the DNS Server address, and that fail. I have gone through a system restore to a previous point (before the day of the crash) but that seems to have made no difference either.
I have attempted to set the IP addresses (for TCP/IPv4) directly IP address 192.168.0.3 Subnet mask: 255.255.255.0 Default Gateway: 192.168.0.1 And therefore forced to set the DNS Server address too Preferred DNS server: 192.68.0.1
But I don't know what to set for the alternate DNS Server, so left blank. This seems to step me forward, in that the device/network is now identified. However the internet access is still not work, as the "DNS Server is not responding".
My netbook shows signals from others in the area but shows a red X next to my router connection. I can't seem to get connected to my own wireless router
My Windows 7 laptop works Fine at home on my broadband with a wired connection, When I take my laptop downtown and try to connect to a company network, via a wire, windows 7 fails to find the connection.
