I've just ordered an SSD for one of the laptops, meaning I'll have a nice 7200 RPM hard drive sitting unused.
My main desktop is a wonderful mini-ITX system with a single M4 SSD. It is currently backed up, along with all the laptops, to an Asus Windows Home Server machine, so I'm fairly confident about my data integrity in case of failure. But realizing that one can never be too safe with the primary desktop, and as the little Antec case has room for a second 2.5 inch drive, it occurs to me that the now-superfluous hard drive could be installed into the desktop and used for periodic (daily?) imaging.
The SSD has the usual mysterious 100 MB recovery partition and a single C: partition for the Windows 7 x64 Ultimate machine.
There's a lot of talk about moving from hard drive to SSD, but going the opposite direction just isn't discussed. Guess this is an odd situation.
So: would I have any alignment issues or other potential snags in imaging my SSD to a hard drive? Would the usual ideally-free software solutions such as Macrium or EaseUs be appropriate for this task?
My Windows 7 configuration is relatively bullet proof (ha ha, nervous laughter).My OS and programs are on C, which I image using RDriveImage every month after Patch Tuesday.My data is on software-mirrored D/F drives.So as long as I don't have a catastrophic event affecting my computer, a routine "drive failure" should be recoverable, with the worst-case being I'd be out a month of updates, but with a good recent image of the OS drive.Anyway, I was recently looking at my event viewer and I have "Disk errors" that occur whenever I run a full image of C.
The complete error text is:
Quote: Log Name: System Source: Disk Date: 7/13/2012 3:38:44 PM Event ID: 11 Task Category: None
[code]....
There were two errors in February (none before that), three in March, four each in May and July.In April and June I did incremental images, so the "bad" area wasn't imaged, so no error.With all the above as background, what's the safest way for me to isolate and/or repair the area(s) of the disk with the errors?The errors are always logged within 1-2 seconds of each other, so I suspect it's just one bad area.And I have never, ever, seen signs of a disk error. No BSOD, no clicking noises, no impaired performance, even for a moment.
I have a hard drive I want to backup to a 64gb flash drive and then restore it to another different hard drive than where it came from. I have windows 7 and office on my laptop and I want it on my desktop pc. There isn't close to 64gb of info on my laptop so it should be fine even though the hard drive says I have 160gb. It is all free space except for those programs.
So, I have a i7 2600K system with a solid state disk as the boot drive, and an older (c2008) Samsung Spinpoint F3 500GB drive as the data drive for programs (that I deem as not worthy of the quick load times). The hard drive has given me some errors over time, and I bought a hard disk to replace it (a Hitachi 1TB). The issue I'm having is that the fact that Windows 7 puts a small (100MB) partition on the F3, and for some reason, even though I'm running Acronis 2012, it doesn't seem to be able to clone the F3 over to the Hitachi. I've also tried Drive XML, and for my 2 hour wait, I only managed to acquire a boot error. Thankfully, I've not done anything rash to destroy the data on the F3, but given the fact that I've seen corrupted files in Steam from that drive, I'm not will to trust it long term with my data. I really need to get the data onto that Hitachi, though... Anyone have any advice for upgrading the HDD in a SSD/HDD system? I don't really feel like it should be so hard, especially if I've bought Acronis True Image, but maybe they haven't designed their product to handle this scenario quite yet?
I have a HP Touchsmart IQ500. Turning my computer PC on today, all I got was a blue HP invent screen with setup, boot menu, system recovery, and system diagnosis, and I could not get past it. I entered the BIOS and figured out that the hard drive was listed as "not installed." Pretty sure that is the main problem.I tried a system restore (with the Windows 7 install disc), but I guess the computer couldn't read the hard drive enough to enter safe mode (I tried restarting and F8ing several times). I put in an external hard drive, and the BIOS read it; however, windows does not allow you to partition an OS on a hard drive.
I have an internal hard disk not in use ,and I would like to make it as external disk !I looked on the net and I found I should have the " encelsure " butt I think I wont find it here in my city .So is there another way ? like usb -esata cable
Me and my brother built me a new computer from scratch (he did the building - i did the watching). I purchased an internal hard drive from Overclockers UK. It's a Samsung 1TB drive. I also have a 64 Solid-state drive in there as my primary hard drive that Windows was installed on and a couple of programs are installed on. My storage disk (the 1TB disk) is for all my music/films etc. Whenever I drag and drop a file into the Samsung hard-drive - it copies it rather than moves it instantly.When I had a laptop, I had 3 external hard drives and this is the way it copied files onto them.how I can get the internal drive to stop acting like an external drive?
I have a virus infected sata hard drive with windows 7 on it. It has the win 7 anti virus 2012 on it, and it's a cybercriminal virus. I have lots of files I want to transfer to the new sata drive. I already have windows 7 installed on the new drive. How do I get the files from the bad drive to the new one?
I have a USB Webcam 6.1.7601.17514 from Microsoft installed on a Fujitsu Laptop (Windows 7 ) and I want to copy and install it on another Fujitsu laptop (Windows 7).The other laptop the camera is not working and there is no webcam driver installed.
my old hard drive that has been my OS drive for years wont cut it.I have an image of my OS but i don't know how to 'image' or install it on the SSD without my cd drive.
I have a Intel 320 120GB SSD that I just installed last Tuesday. Everything went well with loading a image on it from my spinning HDD. Offset is correct and thdrive is running well.I got up the other morning to find that somehow Windows Auto Update had been turned on and the system had restarted after Win Update had downloaded & installed 18 updates without my permission.So today I re-loaded that original image I had used on Tuesday to get rid of the 18 updates (Whether I do them in the further is u to me not MS).This started me thinking about loading a image on a SSD drive.
1) Should I first run the Clean All command to wipe the drive before loading a image on it?
2) What effect does re-imaging a SSD have on the data, partitions and files that are already on the drive?
The program I use is Acronis TI 2011 that they say has full SSD support. But what does that really mean. During the re-image TI deletes all partitions and then recreates them as to what is contained in the image, even if they are the same.Reading some reports about SSDs deleting partitions & formatting the speed of the SSD was reduced by just deleting a partition and then recreating it and wasn't reduced by just formatting it. In fact formatting it seemed to improve the performance.So now I'm wondering Should I go back and format or run the Clean All command and then re-image the drive with that original image.
make a dualboot comp by adding windows XP to a new partition. I created the new partition with 20gb. (From the 500 of my actual harddrive)But before I actually installed on that, I got distracted with a second harddrive that my dad got(for no reason). It had a full copy of Windows XP backed up on it from another computer, so I figured I would just use that for the dualboot. I plugged it in (wired the same way as my old harddrive, but different data slot), restarted, checked the harddrive in explorer - all the data was there / reading correctly / etc, and I used 'easyBCD' to add the new harddrive to the boot list.(Which, of course, crashes if I try to start it. I just wanted to see what it would do). For a reason I can't remember, I unplugged the second harddrive for a bit, started the computer on accident (I don't know if anything loaded before I shut it off), and then when I plugged it back in.Windows 7 would not launch. It goes to a DOS-like window, except it's just a flashing _ and it never does anything even after a few minutes. XP didn't work still.. so I decided to reinstall XP (as I couldn't tell which harddrive was which on the list, I unplugged the main harddrive while installing onto the new).. and when I did this.. it formatted and installed fully... then restarted.. then restarted.. and restarted.. and just kept restarting, never showing any thing past the manufacturer logo/BIOS load-button-message-thing. So, I then try to use my 3-disk Windows7Recovery disk(burned myself with a program apparently included by the manufacturer.) It installed fully, appearing to work.. but when I launched it, it said "Invalid Partition Table" and wouldn't boot past that. When I insert my driver installer disk, it gives me a basic DOS window thing. dir A: shows the files in the disk. dir B: for some reason shows the same. C: says "Error reading from drive C: DOS area: general failure". All other letter:'s just say "invalid drive". (I'm doing this with both harddrives in.) I attempted connecting the harddrives to an old computer, but it gave an error for both. (It detected the harddrives, but said it had an error reading from it. Windows Explorer asked me to format it... {i'm willing to format one of the drives if anybody thinks it will help, but the old harddrive has data I'd prefer not to lose.} ) Looking on google, I saw several problems that all have similar problems (less overdescripptive than I am though) but none of the fixes suggested worked for me. Also - as I have two different with different errors, I only need to make one of them work.)Also - my other available computer has a CD burner / floppy drive if either are required. I also have several USB's. The computer can boot from USB's and CD's (tested), and I could easily take the floppy thingy and connect it to the computer.also - this computer is probably still under warranty unless unscrewing the hard drive voids it. .. does that count as modification of the computer?
Is it possible to use the disk imaging tool for Windows 7 and provided that the hardware platform is exactly the same, use that same image to restore a second machine?
I'm looking for a document scanning software (of course FREE (if available)) to scan in my monthly bills using the automatic document feeder. Once they are all scan in to be able to place them in order. For example my elect bill is 3 pages. Therefore, if I scan it in with all the other bills, and then review it, I would like to put page 3 with the elect bill and not at the bottom of the pile.
I am preparing to replace my primary hard drive. The existing drive has limited space and there are indications that it may not last much longer. I have created a system image on another storage drive and a recovery disk using the software that is built in to windows 7. Is this an effective way to replace my hard drive? Is the windows 7 software reliable?
I recently upgraded my computer with a new motherboard, processor, RAM, and video card. Before I did this, I installed a second fully functional 1 TB internal hard drive just to hold the system image and my important documents. I made a system image using the native software that was available on Windows 7.To be clear, I made a 143 GB system image from my first 1 TB internal hard drive and put it on the second 1 TB internal hard drive. I also moved my important documents over to the second hard drive. (The second drive was completely formatted and turned into a Basic drive beforehand.)After installing the new components, I wiped my first hard drive, deleting all partitions on it, but I forgot that I had one more set of folders that I forgot to move over to the second hard drive. However, since I had the system image on the second hard drive, I figured that I could use that to re-image the first hard drive, pull the files, and wipe it again.Now, since the old motherboard and CPU drivers were saved on the system image, I figured Windows wouldn't be able to load, but as long as the first hard drive contained my files, I thought it wouldn't matter since I could just install the hard drive on the family computer, pull the files, put it back into my computer, and start the installation process all over again.However, when I tried to re-image my first hard drive with the image I had on the second hard drive, I got an error saying that the recovery tools were not compatible, or something to that extent.
At this point, I figured that since the system image was SP1, if I installed Win 7 on my first hard drive and upgrade to SP1, then it would be compatible, so that's exactly what I did.After upgrading to SP1, I tried to re-image the first hard drive, but this time, I used the Win 7 disk in order to do so. I booted from the Win 7 CD, got to the system image restore, and got an image similar to this:Where it says "Intel Raid 0 Volume," I had my C: drive. I assumed that the C: drive was my first hard drive, so I didn't check anything.In the next window, I was told that my first hard drive would be formatted and re-partitioned, so I said yes. When the system was preparing for the re-imaging, I got an error saying that re-imaging failed, and the system would restart.Of course, since my first hard drive was formatted, Windows didn't load, so I tried the re-image again. I didn't get the error, and it showed that the system was "Restoring disk (C: )."However, it was taking WAY too long. 12 hours into the restore, it didn't even go halfway. I left it running while I was at work, and I just came home now and saw that my system was completely frozen. The mouse pointer didn't move, and I left it like that for a few minutes. After half an hour, I held the power button down to turn it off, and tried the re-imaging again.It was going as slowly as it did the second time around, so I canceled the restore, turned it off, registered to these forums off my family computer, and here I am right now.I'm thinking that I should replace all the old parts and try the restore again, but other than that, I'm stuck as to what I should do.
1 x Rosewill CHALLENGER Black Gaming ATX Mid Tower Computer Case, comes with Three Fans-1x Front Blue LED 120mm Fan, 1x Top 140mm Fan, 1x Rear 120mm Fan, option Fans-2x Side 120mm Fan 1 x ASUS M4A79XTD EVO AM3 AMD 790X ATX AMD Motherboard 1 x SAPPHIRE 100283-3L Radeon HD 5770 1GB 128-bit GDDR5 PCI Express 2.1 x16 HDCP Ready CrossFireX Support Video Card
I have a Samsung laptop running windows 7 64 bit. I primarily use a non-administrator account. I got some malware a few days ago. Malwarebytes and MS security essentials seem to have cleared that up, but everything is still running slow in it.Additionally, the malware deleted all the shortcuts from the start menu (S.M.A.R.T. rogue antivirus, I deleted the temporary files before reading that was where the shortcuts were moved to)The administrator account is not suffering from the slowdown, everything seems fine in it. I made a windows repair disc using it.Partitions: there are four right now, windows (100mb), C drive (100gb), D drive (350 gb), and a recovery partition (15gb)1. I'd like to restore/repair windows 7 on the non-administrator account. From what I understand, the registry is likely faulty. I have little understanding of how to fix it, and no image or backup from before the malware infected. My data files are backed up to an external hard drive. I'd prefer to keep the programs registered and installed. I'm interested in dual-booting ubuntu. As the maximum of 4 partitions are assigned, I'd need to remove one of them. I've created a disk image of the system and C partitions onto an external hard drive (using Macrium Reflect). The data files are also backed up, either on that disc or on different clouds. I'd like to confirm that having done this, and having a windows repair disc, it's safe for me to use the recovery partition for ubuntu.
m webcam is not wrking no matter what i do.... i have done everything accept pull it apart... but i have recely gotten my comp back and the harddrive is now new... now my com wont show webcam fee to anyone but i can recienve it, i can hear theother person but they cannot hear me...
I have a USB external hard drive that I keep all my documents etc on (had it for years)I upgraded from Vista Home to & Home Premium then had to upgrade recently to Professional to run my Sage. Through all these upgrades my ext. drive ran fine. Occasionally the drvie letter would change if I had something else plugged into the USB, this was always easily corected in disk management by changing the drive path.The connection on the case packed up so I had to get the drive put into a new case, now when I plug it in the drive is assigned G instead of F, I tried to change the drive letter allocation in Disk Management but it won't let me as the program still thinks I have a second ext. hard drive which is labelled F. I suspect this has happened because when the usb connection broke the drive was disconnected suddenly instead of a proper eject.How do I get Disk Management to remove the inactive drive - i can't find any obvious way - eject, delete etc are all missing when I click on tools or tasks.
I installed Ubuntu on my computer a few months ago and created another partition for it on my 1TB hard drive. I didn't really care for Ubuntu so I decided to delete the partition it was on. That might have been a mistake. Well, now there's 87.68GB of free space on my hard disk that I can't use and I don't know how to add it back to my c: partition.
There was another post about this a couple years ago, but I don't understand the instructions and am not actually sure if it worked. Can someone explain how to do this, please? I'm not completely computer illiterate, but I'm not familiar with partitioning disks. It was just the one time with Ubuntu.
My laptop is Acer with Windows 7 home premium 64 bit OS. It contain only 1 single partition disk that is c drive only.Recently, i accidentally convert the c drive which contain OS into dynamic disk.After i restart the laptop, it shows the following: BootMgr is missing Please press Alt, Ctrl +del to restart Now, i not able to enter the window. I am so worry because my important data is kept inside the hard disk, and i still not yet do any back up copy on it.I searching on this forum and learnt that i need a window 7 installation disk to repair it, but my problem is the computer dealer not give me any windows 7 installation disk when i baught this laptop as their said all the driver and windows program already kept in side the harddisk.I tried to remove the laptop hardisk which is a 500GB toshiba SATA hardisk. Then, i use the other laptop with Windows XP professional with the intention to copy yhe file inside the toshiba hard disk.However, after plugged in the hard disk to the other laptop, under the disk management, it shows that the toshiba disk as : dynamic disk, unreadable.i having problem to backup the data inside the toshiba hard disk.....
I've been noticing after re-installing Win 7 that I get random floppy drive seeks and the hard drive light flashes like crazy and then everything is fine again.I have Clamwin AV,Spyware Blaster and Spybot S&D installed,but that's it,no Windows Defender or Essentials AV.Any ideas what causes this? It's a minor annoyance,but I just want to make sure it's not damaging anything.Also would Readyboost help me? I've got 2 gigs dual channel PC3200 ram(or I could go with 2.5 gig single channel PC2700)and a P4 at 3 gig until I can afford to upgrade my comp.This is my first post in quite awhile so I hope this is in the right place
I installed Ubuntu on my computer a few months ago and created another partition for it on my 1TB hard drive.
I didn't really care for Ubuntu so I decided to delete the partition it was on. That might have been a mistake. Well, now there's 87.68GB of free space on my hard disk that I can't use and I don't know how to add it back to my c: partition.
There was another post about this a couple years ago, but I don't understand the instructions and am not actually sure if it worked.
