I recently bought my new computer, and it came with two RealSSD C300 256 GB. I want to set up raid 0 to have one drive with 512 GB. I really don't mind the performance boost, i just want to have one partition with 512 GB. I already have it on RAID mode, but whenever the Marvel screen appears, i already tried pressing CTRL M, CTRL R, CTRL I, Space, none of those seem to work.
Installed a new M4 ssd today and loaded windows on it. Previously i was using 2 raptors in raid 0 for the os and programs. I re raided the 2 raptors and connected them to the jmicron ports and set them up for raid in bios, then created the raid 0 array no prob. Windows doesnt see the array when loaded up and i have the latest rst drivers installed..did this prior to the os install on the ssd. using the x58 e760a1 mobo. under device manager, the raid controller has an exclamation mark and no driver installed yet i have the latest rst 10.8.0.1003 installed..
I am on the tail end of building my system. It has been quite and experience so far. After an already successful first build, the computer is OC at 3.9 ghz stable but then I felt the urge to upgrade my sole 1TB hard drive ( 32 MB Cache /3 mbs ) into a RAID 0 configuration,using 2 brand new WD 1TB hard drive, 64 MB Cache / 6 mbs, which my Asus supports. I am assuming that this will seriously improve speed and performance.trying to figure out the RAID setup in BIOS and a clean install of Windows 7 64 bit, I finally got it to work. The computer is now operational. But there is only concern I have...
I can't tell any MAJOR improvement ! A slight improvement in speed when I change windows and programs is notice.In addition, the transfer rate when I moved files to the new RAID was quicker at around 88 MBS. Why I am concern is because my Windows system assessment's score for hard disk transfer rate is only at 5.9, which is low and the same as before. Everything else is at 7.5 or higher. Also, I was hoping the load times of my files ( the thumbnail previews ) would increase in speed, but appears to be the same. I am somewhat certain that my RAID setup in BIOS was done correctly. The system is seeing one drive with a 2 TB capacity. I use my computer to do a lot of hd video editing.
1- Is there a way or to test, monitor, or tweak my RAID 0 setup for optimum performance?
2- Am I actually getting the best out of RAID 0 and my expectations were just too high?
3- Are there specifically " one " type of RAID 0 setup? ( I just want to eliminate the possibility of setting up RAID 0 incorrectly in BIOS ).
AMD 965 125 watt ATI 5770 700 watt psu M4a87td EVO 8 gigs of ddr-3 memory Windows 7 64 bit home WD 1TB hard drive 64 mb cache/ 6 mbs ( RAID O )
my goal is to boot windows 7 x64 with raid-1. My boot drive is a SSD, which is not part of the raid array. I have 3 seagate ST2000DM001 that I want in raid-1. I have tried installing windows 7 with ahci in bios first but no luck. I was able to boot from raid1 when I started bios out in raid but my ssd drives read/write speeds significantly decreases.
I was wondering how i can enable Raid-5 in my windows X64 professional ? _The button for raid 5 is greyed out right now and i wonder why ?the motherboard i use is a GIGABYTE GA-890FXA-UD5 AM3 ATX
I have a Biostar mainboard with Sata Raid 0 enabled. I am trying to install win 7 sp1 but the install process asks for a driver. I thought the drivers are on the win 7 disk itself ? I do not have a floppy disc.
I have a smooth running Windows 7 system. I want to convert it to a Raid 1 system. I have a ASUS Rampage Formula motherboard with a Intel X48 chipset and ICH9R installed. It has 4gb memory, Core 2 Quadand a WD 640 gb drive. I have purchased another WD 640 to setup the Raid 1 array. I cannot find anyone who has installed it on a running system, they all build a new system. Can you install Rain 1 on a running system? If so how do you do it?
I've been having some issues with a computer that belongs to CEO of the company I work for. It was built by his son in law and that son in law doesn't really have time to work on it anymore so fortunately "end of sarcasm" that responsibility falls on me.Computer was running great until about two or three months ago where after shutting it down for the night and turning it back on in the morning would cause the computer to reboot three times after going through POST and during 4th time he was able to boot into OS (WIN7 64bit). I updated his bios and that seemed to fix the problem, BUT the computer was set in a Raid 1, but for some reason it is no longer set up that way. I see both HDD as separate HDD in "My Computer" C: & D:, both are 600GB with about 400GB of space free. How can I return them into their raid 1 configuration? MOBO is GA-X58A-UD7 Rev 2, Intel Core i7 970 cpu with 12GB DDR3 RAM Total. He has about $10,000 worth of programs on it (Electrical & Mechanical Engineer) and it would take me weeks if I had to start from scratch.
- build a system with 1 WD1101FALS HDD and installed Windows 7 64 bit no problem. All was good for few days until I got a bug to set up a RAID 10.
- Went out bought 3 more of the same drives. All 4 drives are WD1101FALS 1TB.
- Set up the RAID 10 array on the ASUS motherboard, got the RAID drives for Win7 64bit on a USB key.
- Start install, no problem. Win7 asks for drivers, I click browse and select the drives from USB for the RAID. Install continues, files are copied, thing are flying, it's fast.
- Then 1st re-start
- Windows continues to install (finalizing things, registry update, etc).
- I get to 4 check marks on the Windows Install screen and then it goes into the last step "Completing Installation". The progress bar goes to about 80% complete and then
BLACK SCREEN, computer re-starts. Windows comes up with a message "The computer restarted unexpectedly or encountered an unexpected error. Windows installation can not proceed. etc.." It assks to press OK and and PC re-starts and the installation re-starts from scratch. I tried about 15 times, with different RAID drives, from XP to Vista, to Win7.
I have no clue what else I can try. Usually people have problem with the RAID drives but I have no problem with that step. The drivers are selected and seem to be working fine. The install almost completes.
Here are the images on how far along the install goes. The progress bar actually goes more than that, I just took a picture before the black screen.
I am having trouble installing windows 7 (home premium) on my new raid array (2x intel 330 120GB SSD in RAID0). Basically, windows CAN see the raid volume. it recognies that there is a single 223 GB volume available. I select "Load Driver" for the volume, and plug in my trusty USB with the appropriate intel SATA RAID drivers. Win7 recognizes that there is a compatible driver on the USB, installs it, but still says: "Windows cannot be installed to this disk. This computers hardware may not support booting to this disk. Ensure that the disk's controller is enabled in the computer's BIOS menu". The format and create new partition options are grayed out for this volume.
Using the Intel Rapid Storage Technology tool, I combined the two drives into a raid0 volume. This is confirmed because when I restart, the raid volume shows up in the RST echo with the right size, and also indicates that the volume is bootable. It is also confirmed because the windows 7 setup only sees one 223GB disk. I have confirmed that in the BIOS, the SATA controller is set to RAID mode (not AHCI). I have confirmed that in the BIOS, the first boot option is "RAID intel SSD". I've tried the RAID drivers that came with the motherboard, Ive also tried the raid drivers available from intel and the latest raid drivers available from the motherboard MFR.
I bought an Asus Desktop CG5290-BP007 at best buy, when I opened it says RAMPAGE II GENE/CG5290/DP MB
Asus CG5290 motherboard: Rampage II Gene Micro Atx Processor: Intel I7 920 (2.66 Ghz) Ram: 9GB HD: Seagate 1TB 7200 RPM Windows Vista Home Premium 64
If you want to see the link here it is: http://www.bestbuy.com/site/olspage.jsp?skuId=9366642&type=product&id=1218092150864
I removed the Seagate and I put 2 WD Velociraptors 300 GB each and 10,000 RPM, I have a concern, one it is on the port 1 and the other velociraptor is on port 3.
Does it affect in order to make appear the RAID option in the bios? Because it does not appear, it just appears these options: IDE and AHCI. How come it does not appear RAID in the bios options?
What am I doing wrong? Or what do I have to do in order to setup in the bios as RAID?
I don’t know if this link below it is exactly my motherboard, it seems that my desktop came a little bit different than this motherboard or they designed specially just for best buy, I am not sure about it.
I took several pictures to show you what appears when I turn on the computer and when press <Del> to enter in the bios and when I just turn on the computer and I don’t do anything.
I went to Asus website and I downloaded the manual for Rampage II Gene Motherboard, I was reading it and It says that Intel Matrix Storage Manager option Rom utility will appear when I press CTRL + I , I tried it several times and nothing happens, is that option working in my Asus Desktop CG5290-BP007 ?
Please help me what to do, I would like to install Windows 7, my hard disks are not formatted I think so, because I just installed them and I am not able to see RAID in the bios options, Please tell what steps to follow in order to setup RAID 0 in this computer.
I am getting ready to set up a RAID Array but this is my first time doing anything with RAID. I know how to get into the BIOS and change settings and I know with two hard drives, I should do RAID 1. However, I just have a few questions before I do this. First off, I am an idiot and did not notice that my first hard drive I got when I built the computer has a 32 MB Cache:
Caviar Blue 1TB 7,200 RPM SATA 6.0Gb/s 3.5" Internal Hard Drive WD10EALX - OEM
I noticed it only had a 32 MB CACHE when I went to get another one. I then asked for the version with a 64 MB CACHE (WD1002FAEX), paid for it and left. Will these two hard drives work together in RAID if they have different sized caches?
I am in the process of putting (5) 3TB HDD's into my computer (Windows 7 Home Premium 64 bit) to rip my Blu-ray collection to for playback in my home theater room via a Popcorn Hour player. Each drive is independent and I will be systematically filling one drive before going onto the next.The problem is that the Popcorn Hour players communicate with the PC by specifying one folder via SMB that contains all of my media. Since I am doing independent drives, there will be one master folder on each drive containing all of the media for that said drive. Meaning, in terms of the Popcorn Hour/SMB setup, there are five folders I need it to *see* and catalog.
I have an ASUS Motherboard M4A87TD EVO, got two new hard drives, and changed the BIOS settings to a RAID configuration. After exiting BIOS, I loaded the WIN 7 (64 bit) installation disc, got thru the first few prompts of installation, and the pop up error menu shows up. "No signed Driver Found, Please insert CD/DVD/ Floppy", and my RAID configuration does not appear in the box as a hard drive for Windows to be installed into.
After researching on the web and contacting ASUS, I still don't understand. From what I can gather, it is a driver that will make THE INSTALLATION PROCESS RECOGNIZE MY RAID configuration. Apparently, it must be downloaded onto a thumbdrive and installed "during" the Windows installation. Is it specific to this type of installation, or manufacturer specific? Asus or Windows? A third party??
I had one hard drive failed(640gb). I bought replacement and tried to restore image but it failed. Then I wanted to convert to non raid system. I changed both drives(640gb) to non raid and bios change in advance setup. I am getting error when I try to reinstall win 7, "setup was unable to create a new system partition or locate an existing system partition. See the setup log files for more information". I have deleted old partition many times but win 7 setup on this dell xps435 desktop won't install windows.
I have tried to find the way to do this, but without success as I cannot see the wood for the trees.
I have a mature Windows 7 system, with so many applications loaded that rebuilding from scratch is just not an option. I have a 300MB Velociraptor wholly given over to the OS and another empty 300MB VR. I want to extend, that may not be the right word, my OS to use both disks in Raid 0.
Which configuration would be better using mobo sats 2 raid or using seperate rid controller via pcie card Rosewill Rc-211 wsis3132) or should I use mobo for raid and card for extra sata w/o raid I have more drives than sata slots. How do I transfer data videos/Tv shows from existing drive to raid?
I have Win 7 Pro 64 bit installed on an ASUS P7P55D LE motherboard which supports RAID 0,1,5 and 10 using Intel Matrix Storage Technology through an on board Intel P55 chip set. The system was assembled in Nov 2009 using two Western Digital Caviar Black 750Gb drives in RAID 1 as Drive C:. (I now know from Western Digital Customer Service that I shouldnt have done that, but lets move on from there). Last December, an error message informed me the RAID array was broken and identified one of the 750 Mb drives as needing replacement. I happened to have a spare 1.5Tb WD Caviar Black at the time, so I pulled the 750Mb drive and replaced it with the 1.5Tb drive. Life was once again good. Then on July 4th (wouldnt you know) there was a repeat of the December 2011 error message telling me to replace the other original 750Gb drive. Okay so I had another 1.5Tb WD Caviar Black laying around (dont ask) and did a similar swap out. Thats when I emailed WD Customer Support asking about the 750 since their diagnostic software said the drives were fine. Thats when I learned that I should be paying lots more for enterprise quality drives if I want/need RAID. Well thats not what ASUS says in their advertising, but live and learn. All thats prologue, because my real question is whether its possible to break the hardware-based RAID 1 array and set up a Windows 7-based RAID 1 with the two 1.5Tb WD Caviar Black drives without having to reinstall Windows 7.
anyways, my main drive is a RAID 0 with Vista x64, but I have a second HD that is a SATA 250GB, which I installed Windows 7 on. The only way I could get install to work was to switch my BIOS to IDE mode rather than RAID. I would of course though, like to be able to access my Vista drive from Windows 7 (and more importantly, not have to switch between IDE/RAID mode at all in the BIOS, it's a pain).
Now, the one odd this about this all is that the drivers I have for Vista (x86/x64 drivers) for this mobo's RAID controller WORK when loaded on installation to identify and install to the drive, but seem to not load or not work in any way once the first reboot on install occurs. Maybe this is because I installed from within Vista x64, though.
(Incedentally, my motherboard is an M3A Asus, using ATI's SB600 for a RAID controller)
I've tried loading the drivers from within Windows 7 while in IDE mode, but the install program won't let me. At first it didn't allow because of version restrictions, but then I altered the ini file to get around that, but it encounters some sort of error when installing and quits.
Any help that can be offered, would be grateful. I realise it's a beta and not a real release, so I can get past the BSOD from my odd setup, and I really am enjoying playing around with it so far. Very very impressed.
Edit: Just in case anyone thinks of suggesting me to right-click the inf file and install that way, already tried, won't allow for it.
one of the netbooks was plugged in to initially power it up, but then hard-shut-down before Windows could run through its initial setup.Now when I boot up the netbook, and it attempts to go through the initial windows setup "Setup is starting services", and then throws an error message: The computer restarted unexpectedly or encountered an unexpected error. Windows installation cannot proceed. To install Windows, click "OK" to restart the computer, and then restart the installation.I restart, and the cycle continues. This happens whether I try to boot normally or in safe modeI've got no CD-drive attached to it, so I'm not sure what I can do to break this error cycle.
When I try to install some programs and drivers i get error: 'Setup will only run in administrator mode. setup is aborting.'. I only have one account which has administrator rights. I have already tried to enable and disable UAC, booting in safe mode, run as administrator, enabling original administrator account, adding permissions, taking ownership, changing compability mode and other but nothig is solving my problem. I'm running windows 7 x64 build 7000.
I am trying to upgrade Vista to Windows7 Home Premium and I got this message after the installer copied ~2GB of files on my PC:
"setup can't continue. restart the computer and restart setup. when prompted try getting the latest updates."
I restarted the PC and restarted the setup and I got the same message. I updated the Mother Board Bios and restarted the setup I got the same message. I have tried both options (get update and no update during the setup). And it didn't work.
I do not want to do custom install (fresh install) on my computer.
Recently had my RAID 1 go critical, "a member of the array has failed or is not responding". This happened after getting BSOD while playing Battlefied 3 (that was loaded on the RAID (is serving as C). I replaced one of the drives, repaired the RAID and then loaded Call of Duty MW3 into a different 320 GB drive. That game has also crashed to BSOD and now RAID is listed as critical again. RAID looks like it has split the two drives. One is listed as <LD 2> and the other is listed as <single drive>. Is there a way to get them back together again? Sure would love to find harmony within my computer.
Currently I'm running the RC1. I just got two additional hard-drives to throw into a raid configuration which I set up properly within the bios (worked in XP).
The trouble is when I boot it makes it out of the BIOS and into the Starting Windows Screen. Windows bluescreens at that point. It only bluescreens when I have the RAID option enabled in my bios. I imagine that there aren't drivers for the controller?
When I go to intel's website to install their matrix controller drivers, I get this error: this computer does not meet the minimum requirements for installing this software.
This may just be an idle thought, but I'm wondering if one could setup a RAID configuration across two or more PCs? I know that one PC can have more than one RAID system in it, and even outside of it, with controller card going to an external case, but how about two totally separate PCs only connected via a Wireless adapter on a network?
I'm using a p8p67 motherboard, an OCZ ssd, and two samsung hdd's.
The raid works great, expcept the fact that its always showing empty. I just installed a bunch of stuff to it, but I think that somehow went into the SSD...
I amtryuing to reinstall windows 7 pro x64 on my desktop, but I have a raid 0 array setup. I had it installed on these before I had virus problems, now when I go to install it I cant seem to see the hdd's when in raid in bios, only when in ahci mode
I did have 2 hdds in RAID 0, and wanted to switch to a single disk (so I could swap the motherboard without issue).Cloned the 2 hdds to the single using Norton Ghost. It works fine and the PC boots no problem - but only if the bios (Asus) is set to 'configure sata as RAID'. If I change to 'configure sata as IDE' it won't boot (bsod during windows loading screen).The PC clearly thinks the new, single hdd is still a raid system - which presumably could cause problems when I upgrade the mobo. I have tried Windows 7 repair, fixmbr,fixboot, rebuild bcd... none of it makes any difference! How can I get the PC to realise it's just a single disk?