Extended Display Identification Data Vs Monitor's Native Res
Oct 15, 2012
This has happened to me around some months ago, when i was trying to install some games, and now, whenever i reboot my PC, the screen resolution changes.My native monitor res is: 1680x1050.But on Catalyst Control Center, whenever i reboot, the EDID would show that my max. res is 1600x1200, so i have to manually uncheck the "use extended display identification data or driver defaults" box and set the res to 1680 again.
I don't know whether this is a Windows 7 problem or a Catalyst problem, but here goes...
I have installed Windows 7 (clean) and the latest Catalyst drivers for my ATI HD4850 card. My monitor is a Samsung SyncMaster 2243NW, a 22" panel with a native res of 1680 x 1050. I have installed the monitor driver from Samsung's website and the monitor is now showing correctly in device manager.
When I right click on the desktop and choose "screen resolution", the "change the appearance of your display" screen offers only "display device on DVI" ion the drop down menu, not the Samsung monitor, and does not offer me the native resolution. The nearest is 1440 x 900. If I click "advanced" I'm taken to the catalyst driver screen which correctly identifies the monitor, but bizarrely still offers only the same choices of resolution as the Windows 7 screen. 1680 x 1050 just isn't there.
Can anyone help me get my monitor to run at native res in Windows 7?
I'm having trouble getting my monitor to display at its maximum resolution and I cannot for the life of me figure out what's wrong.
I have an ASUS VH242H 23.6" Monitor which has a native resolution of 1920 x 1080. I originally had windows xp and it could display this resolution just fine. Now, after installing windows 7, when I hook the monitor up to my laptop, I can only get it to display up 1400x1200. Going past this point causes the monitor to flas an out of range message. Furthermore, my computer won't let me designate the refresh rate as far as I can tell. I updated the driver for my graphics card and that didn't seem to make a difference.
I have an HP nw8440 Mobile Workstation with a ATI FireGL v5200 GPU.
I have an HP proBook 4440s and a external HP S2031 monitor. I can get the extended monitor feature to work outside of the VPN. Once I go into the VPN the only thing I can do is move the entire VPN to either screen. I can't share anything within the VPN such as word, excel, or outlook. how I can move items within the VPN from screen to screen?
When I open my Windsor program I can see it is open but it won't show anywhere. I have an extended screen and I can see when the program opens that the screen flashes and it looks like the program is hidden. I have tried all the options I know of including re-installing software.
Some more details. The program I run had four charts open and when I last closed the program I had one of the charts expanded.
I have a Genius GPen 4500 USB graphics tablet (using the built-in Windows 7 driver), and would like to use it on my secondary monitor (which is 4:3, unlike my primary which is 16:9)However, windows seems to have decided that the tablet is integrated into my primary monitor (according to "Tablet PC Settings" in the control panel - it shows "Pen Input Avaliable" for the "1. BENQ E2220HD" item and "No Pen or Touch...." for the "2. SyncMaster" item)Running "Setup" from that window does not work, as the tablet still maps to the primary screen, and can't be used to click on the second screen.
My daughter is a teacher and just got a new smart board installed. She has a Epson projector hooked up and can only get duplicate as an option in Windows 7. It will not let her use the projector as an extended display. She need to be able to change resolutions on each desktop as her laptop is wide screen at 16:10 and her smart screen is 4:3 ratio. She is a math teacher and needs to be able to make correct circles and graphs on both, one has circle while the other displays an oval. I have changed the resolution and can get one or the other to work right, but not both. As far as I know the only way to have different resolutions on each is with extended display.
the display/monitor uses the generic driver for display and it is 1024×768 or 800x600 but it looks very odd it should be bigger because my screen is bigger. I have a acer monitor but is there something I can download to fix the display size?
I am very curious to know how to connect a laptop display to another laptop display. I have an old laptop and a new laptop with windows 7. I did some extended displays to other monitors. But any one have any idea about extending to a Laptop display from another Laptop.
I have 2 displays, 1 is a TV 3 meters away hooked up to my graphics card via HDMI and the other other is obviously my PC monitor. I was hoping there would be a way to have sound exclusively on the TV while I have seperate audio on my monitor?Sorry it's a bit hard to explain. Basically I want to play a game on my PC with my headphones on while a film is playing on the TV, but if I try it atm the game shows on my monitor while the film is playing, but the sound of both is coming out of the TV.Graphics card is a HD6870, using Windows 7 x64.
I just got a new 9800gtx+ . i have a 22" AOC lcd screen. whenever i start my pc , the motherboard screen appears but when the windows loading screen comes my monitor shows the message input not supported I have updated my drivers and checked fastpccheck.weebly.com. but no help. After that screen the user login screen comes to display and then everything is normal. i cant figure out what is making the problem.
I have a ATI Radeon 7500 and i can't let windows 7 Build 7600 find it. It says under display monitor its a Standard VGA graphics adapter. I'm getting really annoyed because i can't play counter-strike...and i installed many different drivers for it but it just doesn't work. and i also wanted the Control Center but idk how as well. I upgraded today to windows 7 from XP...and dumb me didnt backup ANYTHING after a full clean wipe. So im getting really agitated and not patient about it. please help!!
and as well with my monitor display says Generic pnp Monitor and i can't find the drivers for my monitor anywhere! even on the gateway site. I have a 19" Gateway LE HD widescreen.
The only way I could shut acer down was unpluging my computer. The moniter said "no something, I'm sorry but I forget. Is there a way with the keyboard to shut it down? I called my provider and they said it was a moniter or card problem, but it works good since i plugged it back in. I have window 7.
So, I got a Benq G2400WD and a 32 inch LCD TV connected to my computer, to my ati 4890 graphic card, and i wonder if i could set a different font size/dpi on my LCD TV than whats on the Benq?
In Windows CP Display Settings (and in Nvidia CP) my left/main display is 1 and right is 2. In Windows CP Color Management the left is 2 and the right is 1. I would ignore this except that at least a couple applications now open on opposite displays. One is a monitor color calibration program (which also identifies them reversed) and the other a Raw Image Converter. And I don't trust that the calibration program loads the profiles separately.This happened after I reinstalled Nvidia video drivers trying to fix random bsod from firefox and IE8 - which seems to have worked.
I have an external monitor, actually a TV connected via S-Video cable coming out of the back of my video card. My TV is my second desktop. All of that is fine. The problem comes in when I log off or "switch users" (there are no other user profiles on my computer - I only log off or switch user to make sure the kids can't get on without my permission - they don't know my logon code), the TV loses the picture and goes grainy, but when I log back in, the TV does not "kick in" again. The only way to get the TV to display the second desktop after logging out or switching users seems to be to restart the computer entirely. If it reboots, it picks up the TV as second monitor again.
If you simply log in again, it does not pick up the TV as second monitor. Is this related to some setting that says the TV should only be the second monitor on the admin's account and not for "all users" or something? It is annoying to always be restarting my computer to watch a video on my TV. By the way, in all cases, the "Display" settings in control panel show the TV as the second monitor. But looking at the actual TV, all you see is a grainy screen that obviously is not being fed any clear signal.
i have a Sapphire hd 7850 graphics card and two monitors connected to it one hdmi one dvi-d. both screens are showing the same image and when i go into screen resolution it shows only one "generic PnP montitor". this was a fresh install of windows seven and it did work before that. the driver for the graphics card is saying "standard VGA adaptor" is this normal
Can't get monitor to display same resolution between 2 workspaces - Microsoft Community Copy/paste of text in OP (posted Nov 21, 2012): Ok, so here's my setup:HP EliteBook 6930p with ATI Radeon HD 3450 graphics card. Win 7 Pro 32 bit installed.I have 2 workspaces, both with docking stations.Workspace 1 (primary work site) had 24" wide (primary monitor) and 19" wide monitors.Resolutions that Windows let me set were 1920x1080 and 1440x900, respectively. These monitors were also hooked to the docking station via DVI and VGA cables, respectively.Workspace 2 had a 19" standard monitor (1280x1024, VGA, set as primary) and then I would open the laptop beside it for the dual monitor (1280x800).Today I have pulled the 19" wide from workspace 1 to replace the 19" standard at workspace 2. Windows, however, will only let me set the resolution to 1280x720 (still using VGA). Even taking off the "hide modes" option or going into the ATI Catalyst Control center to try and force it does not work. I've also tried switching between which one is primary or even making it single monitor display (on the 19" wide). 1440x900 is simply not available.
Windows 7 installed without any problems, and found all the hardware devices, but the only problem I have is that the monitor will only dislplay at 1920x1080. If you lower it , the monitor will not display a full screen. Tried all resolutions, and have the latest 191 drivers. Any ideas..
Windows 7 Home Premium - Fully updated as of today NVIDIA GeForce 9200 - Fully updated driver to the newest one released
When I look under windows display settings or NVIDEA settings there is not an option for a second monitor any more. There used to be. Now that I got a VGA spliter, there is not. I have tried a combination of everything from direct computer to 3 different monitors, all work perfectly, but when I attached 2 monitors with the spliter, all I get is the same image on each monitor.
When I hit detect, nothing happens, both monitors are identified as #1. Have rebooted, have updated, have done just about anything I can think of. Why would windows not show a second monitor option now?? Spliter and monitors work perfectly with the laptop and second older/slower computer. But on this better computer, faster and just should be a hell of a lot better computer, I am not getting the option for a second monitor.
I recently for the first time went over my monthly data cap for broadband and looking it to it a bit more it looks like a lot of the programs my kids are using are hogging the bandwidth. I don't really want to pay for more bandwidth (as I already pay way above average as I live in a small rural village) but I don't want to restrict too much what my kids are doing. The solution to me seems to be to see if I can monitor and if possible control to some extent the data on each of the IP connected to the router if that is at all possible. I have looked at my router settings and unfortunately they do not permit anything more than traffic monitoring and there are no custom firmwares to allows additional features of any use. Is there any software that I could use to do this?
I access my Internet via a wireless USB Modem Stick. Living in South Africa, Internet usage is sky high. I would like to know how to monitor my Internet usage. I.ow, which precise programs are running stealthily and eating up my data. I can actually see from my Modem Interface how the data is consumed.I would also like to know How do I use Wireshark to capture wireless traffic? Do I require an add-on card to do this?
I have a quick question about the USB ports on my computer. I have a screenshot hosted here on Flikr: USB | Flickr - Photo Sharing! Of the 5 USB's that are listed, one is a USB2. Is the USB2 Enhanced Host Controller a USB2.0 port? I am looking because I am going to buy an audio interface and if I have a 2.0 in there then I will get something a little better 'cos I want as little latency as possible when recording vocals.
There is one other thing also, if it turns out that there is a 2.0 port, is there a way to physically differentiate which port is the 2.0? I have 3 USB's on the back and 2 on the front of my tower. At the moment I don't know which is which and do not know what to physically look for when I look in or out of the case.
The computer I'm using is older (3+ years) and has frustrated me a few times, most notably in the past 2 months.
That said, this is a new problem. My second (DVI) monitor is detected by Windows but doesn't display anything. In both the display settings and the NVIDIA control panel, I can see a second (Impression) monitor, but it's blank and I can't get it to show anything. In fact, the monitor doesn't seem to recognize that it's connected, because the orange "power but no input" light is on rather than the green "power and input" light.
This is a Windows 7 64-bit installation on a Dell Dimension E520.
I use a lap top with an external monitor.In the Display Control Panel, there are THREE monitors listed:
-The lap top -The external monitor I use -Another monitor called "No Monitor", (excellent name!).
I've configured the No Monitor to the pull down option "Disconnect This Display", but it's still there. It's not a big deal, but I was just wondering if there's a way to remove it altogether.
Well, running Windows 7 ultimate on a Dell xps m1330 laptop. Everything looks good, but at work I am connected to a matrox triple-head-to-go device which is connected to (3) 22' monitors (3840x1280 resolution). Now when I connected it, ran the nvidia app, it found it and worked great.
Problem is I get home, no external connected, so running off the laptop with the basic resolution, I am trying to start apps (firefox, stickies, etc.) and I guess they were in other spots at work as I don't see them.
I forced a close on FF, then re-started, rt clicking and maximizing which worked, but then other apps like stickies don't have that option. An alt-tab shows it running in the lower right (see screenshot), but there is absolutely no way of getting to the app! I did close the app completely and restarted, but it does restart in a location not on the screen.
my problem is without using this tutorial when i add the dvi leads to the monitor and connect on back of pc it loads up but when playing music videos it tends to refresh continously and can never watch a video clip properly. the correct drivers are in there as well..
So now i have a 22inch lcd monitor screen that wont display properly when using the dvi leads..
I have horizontal lines that scan my monitor whenever i play a game. I can see the horizontal lines only on darker colors like grey, dark-green etc. I have a Samsung E2220 display that runs at 1080p on 60hz on a vga cable (no hdmi/dvi support on it). I tried another vga cable, i tried another power cable but with the same result.I have all drivers updated (monitor and other hardware). My current PC specs are: AsRock N68-C S UCC, Phenom II x4, 4Gb DDR3, Radeon HD7770, 500gb HDD Sata3 and a power supply Sirtec 500W 80+.If I open Far Cry 3, for example, i get those horizontal lines. If i minimize the game i still get the horizontal lines if i have something dark on my display (a grey/dark-green/dark-blue website).Before the HD7770 i had a GTS 450 and had the same problems. Could it be the PSU, or the motherboard or what? I also tried a different display monitor (on the VGA) and had the same horizontal lines scaning my display monitor.
Im having a really tough to TS problem with the reliability monitor. For the last week, it no longer displays any data and the graph dosent render.
It just display as blank with no data. Some things to note...
1. The RAC published and State data are being updated and published each day as they shouold. So the data does exist.
2. I have tried the "Resetting RAC" methods that worked for Vista. But the fix dosent work for Windows 7.
3. I cant think of anything that may have changed. I havent deleted any folders or log files.
4. I've used Process Monitor to trace the events when the reliability monitor executes and everything looks fine.
5. There are no errors or warnings in the event viewer.
6. I havent installed any Windows Updates.
So Im hoping that someone can think of something I am missing here. Oddly it used to work for some time and i ran it each day. Then all of a sudden one day it just stopped.
Could this be a permission issue possibly? I do recall changing permissions for C:UsersMeAppData. Are there any folders or logs within that path that might affect RAC? Are there any services that are required for RAC to collect and render data?
